Search Documents

By María Cristina Ruiz

Enargite rich copper concentrates can not be treated by conventional smelting/converting technology and thus nonconventional methods such as leaching must be used. Since enargite (Cu3AsS4) is a hard to dissolve mineral in acidic solutions, pyrite, a common impurity in copper concentrates, could be used to increase the enargite dissolution rate. On this matter, we present in this work experimental data on the pressure leaching of a mixed enargite-pyrite concentrate in H2SO4-O2. The results show that the dissolution of enargite from the mixed concentrate is considerably faster than the dissolution of pure enargite mineral. The leaching rate increases significantly with temperature. Over 98% of enargite was dissolved in leaching 64 micron size particles at 200 ºC and 100 psi of partial pressure of oxygen in just 30 minutes. A change in the partial pressure of oxygen from 50 to 150 psi showed also a large influence in the leaching rate.

Jan 1, 2010

By Gabrielle Gaustad

For aluminum, substitution of primary with secondary resources decreases energy consumption; this energy advantage creates a strong economic incentive to recycle. Several authors have raised concerns that the current sinks for secondary materials may soon be saturated, impeding subsequent expansion of recycling. This work combines dynamic material flow analysis with optimal batch planning models to quantify the significance and drivers of these pending limits under several scenarios, and thereby explore potential opportunities to increase recycling. An aluminum recycling system case was developed that includes containers and packaging, automotive, and construction products and scraps. The impacts on aggregate scrap utilization and materials cost are explored in the context of changing alloy demand and lifetime. Insights drawn from this specific case study could be applied to multi-stakeholder, systemic models.

Jan 1, 2010

By Elsa Olivetti

Life cycle assessment (LCA) is used increasingly as a tool to provide quantitative metrics of environmental impact and inform early stage materials selection decisions. One common challenge in LCA stems from allocation of burden when multiple adjacent products share some of the same processes. A critical example of this is the partitioning of benefit or burden at product disposition in open-loop recycling scenarios. This work reviews the challenge of allocation and investigates the various methods proposed for allocating end-of-life (EOL) burden. Specifically this work examines whether these methods lead to different results and explores the trends in allocation method bias for or against particular materials classes.

Jan 1, 2010

By Daudi R. Waryoba

Keywords: Wire Drawing, OFHC Copper, Recrystallization, Orientation imaging Microscopy (OIM), Texture inhomogeneity Textural inhomogeneities have been investigated in oxygen free high conducting (OFHC) copper wire drawn at room temperature to a true strain of 2.31, and isothermally annealed at 250°C and 750°C for annealing times ranging from 10 s to 1 hr. Local orientations were mapped by means of orientation imaging microscopy (OIM). The microtexture of the drawn wires showed a strong <111> + weak <100> duplex fiber texture at the inner core, whereas the mid and surface regions had a comparatively weak texture. Annealing at 250°C resulted into a recrystallization which originated from the mid section, proceed towards the surface regions and ends in the inner core. Recrystallization resulted into a strong<100>+weak<111> duplex fiber texture. A similar textural inhomogeneity was observed during short annealing at 750°C. However, prolonged annealing gave rise to abnormal grain-growth that proceed from the inner core to the outer surfaces with a dominant <111> fiber component at the inner region and mixed components of <111>, <100>, and <112> at the outer surfaces.

Jan 1, 2005

By M. S. Borges

The need for the waste management industry to reach environmental patterns, technological innovation, and a technological demand of the productive sector is covered by this study. The environmental care and responsibility in the industrial sector and the necessary cultural changes for companies and entities is also emphasized. A collaborative tool was developed to help all partners involved in the environmental administration. This tool focuses on the interaction among residue generators in the productive chain. It was developed for a vehicle assembler company supported by entities or institutions with emphasis in the research, development and innovation, with expertise and capacity for new products creation, as well as reuse, recycling and reduction of by-products generation. The work aims to establish a tool for socio-environmental management, focusing on promotion and interaction between industrial waste generators sectors.

Jan 1, 2010

By Yoshio Nakano

Keywords: Tannin gel, Palladium, Separation, Redox We have developed the novel recovery system of palladium from wastes, which is simple and generates little secondary waste in comparison with the conventional recovery processes, using tannin gel particles synthesized from condensed-tannin molecules. Pd is adsorbed onto the tannin gel particles through inner-sphere redox reaction mechanism: two-electron transfer from tannin gel to Pd(II) species, accompanied by ligand exchange between chloropalladium(II) complexes and tannin molecules. In addition, we propose the separation system of Pd and Au from Pd-Au mixture, which is feasible due to the difference in oxidization and reduction potential between Pd and Au species: PdCl3(H2O)? and PdCl42? are less adsorbable than Pd species containing fewer Cl, such as PdCl2(H2O)2 and PdCl (H2O)3+, while such a distinct difference between Au species is not observed.

Jan 1, 2005

By Vinay Kumar

The present investigation describes R & D studies carried out for recovery of copper from the sulfate solution expected from the leaching of e-wastes in presence of minor constituents such as cadmium, zinc and nickel using solvent extraction process. In order to extract copper in continuous mode in mixer settler unit (MSU), basic studies have been made to optimize the experimental condition using 5%LIX84 in kerosene. Subsequently, the solvent extraction of copper was made in MSU maintaining leach solution flow rate 4.0 L/h and A/O ratio 1. The results showed complete extraction (~97%) of copper in three stages at A/O ratio 1 from the aqueous solution containing 1.98g/L Cu at pH 1.91 in presence of impurities. Loaded metal was completely stripped after scrubbing with 10% sulfuric acid in two stages. The stripped solution could be used for metal/ salt recovery by electrolysis/ crystallization.

Jan 1, 2010

By Geysen. Daneel

Better slag valorization is part of improving the sustainability of steel, stainless steel and non- ferrous metal production processes. Besides, it can improve the sustainability of other products and production processes as well. A sound and well established slag valorization is beneficial for the overall economics, marketing and appreciation of the metallurgical process and its products. On 6-7 April 2009, the First International Slag Valorisation Symposium was held in Leuven, Belgium. This paper gives a brief summary of the symposium, providing an overview of slag valorization opportunities. The authors believe that high temperature process slags can have interesting applications and that within the next 10 to 20 years slags will need such valorization options in order to compete with other materials and get general support for further production. On the other hand, the authors also expect a higher demand for slags for the production of various materials. High temperature processes should anticipate on the growing opportunities for valorization of slags and increase the resilience of their process by better understanding slag processing, slag quality and material requirements. More interdisciplinary research efforts are required to reach this level of knowledge for the different high temperature processes. Such an interdisciplinary research platform was recently established at KULeuven, Belgium, named SMART-PRO2 (Sustainable Materialization of Residues from Thermal Processes into Products).

Jan 1, 2010

By Jilai Xue

Industrial wastes containing 30-50 wt.% Al2O3 and 40-60 wt.% SiO2 may serve as an alternative resource for producing Al-Si alloys. Various raw materials such as used refractory materials from metallurgical furnaces, coal fly ash, andalusite residues, and so on were tested in laboratory to produce Al-Si alloys using carbon-thermal reduction process. A mixture of anthracite and petroleum coke was used as reducing agent. One of the most important operations was to prepare the briquettes made of different raw materials with varying contents of Al2O3 and SiO2. The effects of briquette property, A/S ratio (mass ratio of Al2O3 and SiO2), the amount of carbon reducing agent, on the reduction process and the resulting metals were investigated. The results are useful for development of an alternative technology for Al-Si alloy production, which has the potential application in recycling metals from industrial wastes containing Al2O3 and SiO2.

Jan 1, 2010

By Felipe Perissé Duarte Lopes

The tensile properties of DGEBA/TETA epoxy matrix composites reinforced with different amounts of curaua fibers were evaluated. Tensile specimens with up to 35% in volume of long, continuous and aligned curaua fibers were room temperature tested in an Instron machine. The fracture was analyzed by SEM. The results showed significant changes in the mechanical properties with the amount of curaua fibers. This was compared to other bend-tested composites with distinct matrices. The fracture analysis revealed a weak fiber/matrix interface, which could be responsible for the comparatively low performance of some properties.

Jan 1, 2010

By Fanke Meng

Electrolyzing oxides of titanium, aluminum and niobium could prepare high-Nb bearing TiAl alloy (Ti-45Al-9Nb) at 1500°C. The chosen electrolysis voltage is 3.5V, which is lower than reducing voltage (~4.7V) of electrolyte CaF2, but higher than that of titanium, aluminum and niobium oxides. The investigation shows that compared with traditional methods, this method for preparing high-Nb bearing TiAl alloy is of many advantages such as few steps, friendly environment, low energy consumption, low cost and high current efficiency.

Jan 1, 2009

By Ram Avtar

High tensile thick plates (>80mm, weight ~3000 Kg) of medium carbon low alloy steel, when heat treated, manifested higher percentage of crystalline area (>20%) in fractured surface. Such problem was not encountered in thinner plates. The genesis of higher crystallinity in fracture was examined. It was observed that the thicker plate undergone slower rate (Average 0.9oC/Sec.) from soaking temperature to Ms temperature) of cooling after austenising during oil quenching and thereby quenched microstructure had upper bainites. During tempering of as quenched bainite, additional precipitation took place at the lath boundaries of bainite. This led to weakening of grain boundaries and aided easy crack propagation during fracture and resulted in formation of higher percentage of crystalline area in fractured surface. Enhancement in cooling rate (Average 1.8oC/Sec. from soaking temperature to Ms temperature) of austenised plate by switching over from oil quenching to water quenching practice resulted in complete transformation of austenite into martensite and produced ductile fracture (zero Crystallinity). Plates conformed improvement in mechanical properties between 2-5%.

Jan 1, 2009

By Emma Arakelova

?2?2 (98 %) vapour passed through a reactor at 25Pa where a Zn? target was placed at 273K- 373?. Experiments were carried out on a flow- type vacuum device. ?2?2 decomposition on Zn? surface accompanied by formation of a Zn-containing volatile complex which transferred to the gas phase, and Zn? deposited on a substrate at condensation. As the substrate, five sequentially located quartz cylinders were used at 293K- 423 K (?n). Decomposition of the Zn-containing complex on quartz substrates carried out as a first- order reaction. ?The complex decomposition constant (??) increased with the substrate temperature (?n=293 K, ??=7.05 sec-1;?n = 373 K, ?? = 87 sec-1;?n = 423 K, ?? =158 sec-1). ?The complex decomposition constant did not practically vary when the target temperature increased; the complex formation rate increased slightly.

Jan 1, 2006

By W. M. Cross

Bubble attachment time measurements for the rare-earth phosphate minerals monazite and xenotime were made as a function of oleate concentration, sodium fluoride addition, and temperature. Results indicate that the rare-earth phosphates behave similarly to other phosphate minerals, notably collophanlte and fluorapatite, which have been studied previously. The addition of sodium fluoride yielded a modest decrease in bubble attachment time with fluoride additions below the apparent fluoride surface precipitation point, while at fluoride additions greater than the apparent precipitation point a significant decrease in attachment time occurs. Increasing the temperature or the system gave a slight decrease in bubble attachment time in the absence or sodium fluoride. With sodium fluoride addition and below the apparent fluoride surface precipitation point, an increase in temperature actually increased the attachment time. For sodium fluoride additions above the apparent fluoride surface precipitation point, a temperature increase significantly decreased the attachment time.

Jan 1, 1989

By Zeljka Pokrajcic

Crushing and grinding, or comminution, circuits are the most energy intensive process of a mineral processing plant. Comminution involves the physical size reduction of an orebody to a particle size sufficient for recovery of the mineral values. However, the comminution process remains inherently inefficient. The inefficiency is a result of the operating nature of comminution devices such as grinding mills, where transfer of energy between grinding media and particles in unconstrained and completely random. New comminution circuit design strategies are presented in this paper. The aim of the new strategies is to improve the overall efficiency of the comminution process and reduce the total energy consumption of a comminution circuit. The energy efficient strategies include the: ? rejection of coarse size liberated gangue from the comminution circuit and further downstream size reduction ? use of more efficient grinding and crushing equipment ? the selection of coarser particle product sizes to alleviate the increased energy intensity required to achieve finer product sizes Singularly and when combined, these energy efficient strategies can significantly decrease the overall energy consumption of a comminution circuit. This paper also explores the financial impact of certain energy efficient strategies using an analysis tool called EcoNomics?. It shows that substantial financial gains can be made by including more efficient technologies and methods in comminution circuit design.

Jan 1, 2010

By Linda Gaines

Use of vehicles with electric drive, which could reduce our oil dependence, will depend on lithium-ion batteries. But is there enough lithium? Will we need to import it from a new cartel? Are there other materials with supply constraints? We project the maximum demand for lithium and other materials if electric-drive vehicles expanded their market share rapidly, estimating material demand per vehicle for four battery chemistries. Total demand for the United States is based on market shares from an Argonne scenario that reflects high demand for electric-drive vehicles, and total demand for the rest of the world is based on a similar International Energy Agency scenario. Total material demand is then compared to estimates of production and reserves, and the quantity that could be recovered by recycling, to evaluate the adequacy of supply. We also identify producing countries to examine potential dependencies on unstable regions or future cartels.

Jan 1, 2010

By Xi Zhang

A technique for fabricating free-standing, high-aspect-ratio porous and pillar-type Ni structures has been developed using wet Si processing. A wafer of (100) Si was initially etched in HF solution to form deep pores with micron-sized diameter. The aspect ratio can exceed 200. By introducing the as-etched Si into a defined aqueous Ni2+ solution, Ni deposits grew rapidly onto the sidewalls and replaced the Si. Long-time immersion allows the Si sidewalls to be completely converted and thus form a metallic Ni structure with high-aspect-ratio pores. It is known that close-packed submicron Si pillars can be formed by oxidizing and subsequent etching of the macropore sidewalls. Treated in the same Ni solution, high-aspect-ratio Ni pillars were correspondingly emerged by replicating the original pillar-type Si structure.

Jan 1, 2006

By Helvio Pessanha Guimarães Santafé Jr.

The coir fiber extracted from the husk of the coconut has been extensively used as polymer composite reinforcement in a variety of industrial applications ranging from civil construction to automobile seat cushions. The hydrophilic coir fiber does not act as an effective reinforcement owing to its low interfacial strength with hydrophobic polymers. As a consequence, coir fiber composites display relatively low mechanical strength. The objective of this work was to investigate the effect of an acetylation treatment of the coir fiber surface on the mechanical behavior of epoxy composites with amounts of fibers up to 30% in volume. Coir fibers were immersed in an acid solution of acetic anhydride for one hour, washed and dried, before mixing with DGEBA/TETA epoxy to fabricate the composites. Flexural mechanical properties were obtained by bend tests. The results showed significant differences to similar composites with alkali treated coir fibers that have been previously investigated.

Jan 1, 2010

By Zhou Wenbin

In this paper the mechanical properties of high carbon equivalent cast iron for automobile brake discs were analyzed through thermal analysis curves. Experiment results show that the mechanical properties have a strong correlation with thermal analysis curves and an effective way to predict the mechanical properties of high carbon equivalent cast iron was proposed based on the features of thermal analysis curves.

Jan 1, 2010

By Elisa Alonso

Manufacturing firms that rely on finite resources have a stake in ensuring sustainable materials use. Higher material prices and uncertain material supply, consequences associated with scarcity, can be damaging to firms. Firms have a number of options to improve material sustainability including dematerialization, material substitution and recycling. However, these options require technological capability, capital investments and supply-chain infrastructure; firms may decide to make such investments only if material prices increase. Once decisions are made, the barriers and delays to implementing changes may harm firms. The impact of not reacting to changes in material supply on firms was examined for the case of different platinum-using industries. It was found that taking action is particularly important for firms when limited material availability leads to volatile market conditions. Industries can benefit especially if they ensure process flexibility and have options for changing their material use patterns.

Jan 1, 2010