Search Documents

By Z. C. Song

[THIS PAPER WAS TRANSLATED FROM CHINESE TO ENGLISH BY S. S. PENG, WEST VIRGINIA UNIVERSITY] Immediately after coal extraction, the pressure that causes the movement of the surrounding strata is called mine pressure. Through the strata movement, certain features such as supports taking load arise. This is called "manifestation of mine pressure". The existence of mine pressure is ab¬solute whereas its manifestation is relative and conditional. The visible movement of the surrounding strata occurs only when the applied pressure exceeds the plastic breaking strength. Me support begins to take load only when it offers resistance to the strata movement. The key to investigating mine pressure and its control hinges on understanding the rules and conditions for the manifestation of mine pressure. Since the face moves continuously, the mine pressure and its manifestations are also constantly changing. 'Therefore, it should not only emphasize to obtain its instantaneous magnitude, but more importantly the rules of development changes and their relations to the movement of overlying strata. Once this is resolved, one can estimate the movement of the overlying strata through mani¬festation of mine pressure and predict the time and magnitude of incoming roof weighting. Consequently the location and timing of rib excavation can be correctly selected and thus solve several major problems in the design of mining operation.

Jan 1, 1982

By Hanjie Chen

A mine panel collapse may occur when pillar sizes are too small or the surrounding rock strata (roof or floor) yields. After a small pillar fails, its loading is rapidly transferred to adjacent pillars that in turn fail. If the surrounding rock strata yield, the loading on pillars will redistribute. which may result in some pillars under high stress. This paper analyzes the causes of two cases of mine panels failures in two room and pillar mines. One case of massive pillar failure occurred in a phosphate mine and the other, mine panels failure, is in a coal mine. In the phosphate mine, both the roof and floor strata were a thick competent shale stratum. The finite element analysis shows that the major reason for the massive pillar failure is that the pillar sizes were too small in a panel. In addition, the high cliff topography has some influence on the failure. In the coal mine, the failed area was about 1,000 ft long by 760 ft wide (covering more than 3 panels) involving 390 pillars. The harrier pillars between the panels were punched on retreat into small chain pillars and the extraction ratio in this failed area was more than 80%. The roof remained intact, and pillars were crushed and punched into the floor. Based on the stress analysis, it is found that multiple panel collapse occurred because the barrier pillars were punched into small pillars and the loading on panel edges increased due to floor failure.

Jan 1, 1999

By Chris Haycocks

The relevant literature concerning ground control, mine planning and reserve conservation in multi- seam mining is reviewed. Factors affecting interaction, interaction mechanisms, and design guidelines are presented in detail. The impact of multi-seam mining on future mining, measures for ameliorating negative interaction effects, and future research needs are also discussed.

Jan 1, 1990

By David Newman

The Southern Appalachian coalfield has a long history of coal bumps that are attributable to a unique combination of topography, geology, and multiple seam mining. The high pillar stresses that generate a coal bump result from: i. mountainous topography where the overburden commonly exceeds 1,500 feet beneath ridges, ii. multiple seam mining, iii. thin interburden between active and abandoned mines, iv. thick beds of competent sandstone and sandy shale strata throughout the stratigraphic section, v. strong coal seams, and vi. irregular pillar and mining geometry in older room-and¬pillar mines. Coal has been intensively mined for more than 100 years in Eastern Kentucky, Southwestern Virginia, and Southern West Virginia. As a result, it is commonplace to have abandoned mines above and/or below active operations. Therefore, those conditions that generate coal bumps will be more prevalent in the future, as underground mining continues in Southern Appalachia. The focus of this paper concerns two coal bumps that occurred in the Kellioka seam where both undermining and overmining had occurred. The purpose of the investigation is to determine the magnitude and distribution of vertical stress that initiated the bumps, to identify bump-prone areas in the unmined reserve, and to recommend pillar centers and mining layouts to avoid future bumps. The state of stress in three vertically adjacent seams was examined using the LAMODEL boundary element program. Large, detailed numerical models were constructed of both bump areas and of the remaining unmined reserve block. The results of the numerical analyses were compared with those obtained using analytical equations.

Jan 1, 2002

By Asmaa Yassien

Finite element models were developed to study the effect of tensioned and fully-grouted bolts on the stability of the mine opening in a three-entry development system using a typical geological column for the Pittsburgh Coal Seam. The models were used to study the effect of each bolt type on the stress distribution in the immediate roof, yield zone development and the vertical deformations. Comparison of all of those features show that the effect of a tensioned bolt on the stress distribution in the immediate roof is restricted to limited areas, whereas the fully-grouted bolt has a much wider effect on the stress distribution. Both types of bolts can reduce the yielding and deformation in the immediate roof to different degrees. The fully-grouted bolt reduces the sliding along the bedding plane more than the tensioned bolt. Both types of bolts were able to maintain the bedding planes without separation. The induced forces in both types of bolts are analyzed. A rapid increase in the shear force and bending moment occurred in the fully¬grouted bolt due to the relative motion of bedding planes.

Jan 1, 2002

By David Oyler

Unusual circumstances may require that a longwall retreat into or through a previously driven room. The operation can be completed successfully, but there have been a number of spectacular failures which exposed miners to serious roof fall hazards. To help determine what factors contribute to such failures, the National Institute for Occupational Safety and Health (NIOSH) compiled a comprehensive international database of 130 case histories. The cases include five failures where major rock falls occurred in front of the shields, and six even more serious failures involving major overburden weighting. This suggests two room failure mechanisms. The first is a roof fall type failure caused by loading of the immediate roof at the face as the fender narrows. The second is a weighting type failure caused by the inability of the roof to bridge the recovery room and face area, and affecting rock well above the immediate roof. The data indicate that the roof fall type of failure is less likely when intensive roof reinforcement (bolts, cables, and trusses) is employed together with higher-capacity shields. The overburden weighting failures, in contrast, occurred when the roof was weak and little standing support was used.

Jan 1, 1998

By Y. P. Chugh

The paper discusses laboratory and field studies to analyze time-dependent deformation behavior of immediate weak floor strata in an Illinois coal mine. In the laboratory, core samples of the immediate floor strata were subjected to incremental creep tests under unconfined compressive stress. Both axial and lateral creep deformations were recorded. Time-dependent behavior was reasonably characterized by a Burger model with one Kelvin-Voigt unit. The elastic and viscous parameter8 of the model were found to be stress-dependent, but in the range of 40% to 80% of the failure stress, the effect of stress was relatively small. Therefore, a linear visco-elastic model was developed to represent the laboratory time-dependent behavior of immediate floor strata. Such a model may be acceptable for the design of partial extraction mining systems having extraction ratios of 40% to 60%. Field observations of roof-floor convergence (floor heave) at the mine also indicated a time-dependent behavior similar to that observed in the laboratory. Field time-dependent behavior was also characterized in terms of a Burger model with one Kelvin-Voigt unit to obtain scaling factors between the field and laboratory parameters. This approach should help in predicting likely floor heave in the mine based on laboratory creep tests. It was concluded that additional studies in the field are required to arrive at more reliable correlations between the two sets of parameters.

Jan 1, 1987

By John Ellenberger

The nature of competition in the coal market tends to deplete the most favorable coal reserves first, and forces subsequent development of mines in more extreme ground conditions such as those associated with multiple-seam mining. In fact, 70% of the United States coal reserves are in multiple-seam situations. The National Institute for Occupational Safety and Health (NIOSH) is conducting research to develop mine design algorithms that will result in safer multiple seam mines. This paper presents an overview of multiple seam issues in the central Appalachian coalfields. To date, more than 50 case histories have been analyzed from 20 operating mines in Eastern KY, Western VA, and Southern WV. Each case history is classified according to the degree of multiple-seam interaction, ranging from no apparent interaction to severe interaction with direct impacts on mine safety and resource recovery. The case histories are also examined with regard to amount and geologic characteristics of interburden and overburden, and design stability factors. The sequence of mining has also been found to be critical when the lower seam is fully-extracted. This paper compares current case histories to traditional rules of thumb. In addition two situations were modeled using LaModel software. LaModel has been upgraded to import pillar grids and topographic data from AutoCAD files. The cases presented demonstrate vertical stress capabilities of LaModel.

Jan 1, 2003

At any given lime, the tidal force subjects massive regions to a spatially uniform load. The deformation of any large structure due to these forces is proportional to the elastic properties of the structure. In this aspect, the tidal force applies a load in a manner similar to that of a large-scale testing machine. Any anomalies in the measured tidal response must reflect alterations in the average elastic response of the massive structure. In the present work, tidal tilt measurements obtained in the wall of a large dam are used to infer changes in the response of the dam to applied loads. In particular, it is found that the dam response has changed by approximately 13 percent, on average, for two monitoring periods separated by 5 years. It is possible that these changes were produced by the different volumes of water in the dam for the monitoring periods. The tidal measurement technique can also be applied to monitor changes in the average structural response of large underground and surface masses relevant to coal and metal mines.

Jan 1, 1992

By Brian Clifford

Thoresby Colliery is in the process of recovering an old roadway that was flooded following the closure of an adjacent mine. The aim is to re-use the roadway as a gate road for a longwall retreat panel and it is therefore important to establish the condition of the existing rockbolt support during the recovery operation. Two NDT methods, ultrasonics and RMT's newly developed RF (Radio Frequency) system were used in combination to interrogate the rockbolts to determine their condition. This paper describes the condition of the rockbolt supports, the NDT methods used and the problems that had to be overcome to successfully apply the two methods.

Jan 1, 2002

By André Vervoort

To learn more about the fundamental roof behaviour in South African coal mines, accurate underground measurements of roof deflection were conducted in bord and pillar panels during development and pillar extraction. To conduct these measurements a survey levelling technique was adapted. The overall system reading accuracy was established as being within 0,4 mm on a 15 m sighting distance. The underground sites were modelled and, for a roadway development, similar symmetrical curvatures were calculated by a linear elastic model, as were measured underground. In a pillar extraction panel, a significant amount of bed separation was measured and the roof underwent an a-symmetric movement due to the close presence of the mined out area at one side of the roadway.

Jan 1, 1992

By John Latilla

Following its introduction on underground collieries, the mandatory Code of Practice to Combat Rockfall Accidents (CoP) was applied to all opencast operations of lngwe Collieries (the South African division of BHP Billiton Energy Coal). The CoP includes, but is not limited to, requirements to assess hazards, manage them and monitor compliance. Information on methods to measure highwall conditions and compliance with control measures on opencast strip mines, as opposed to open pit mines, was found to be anything but freely available. However, on the Ingwe underground mines, a system of rating physical conditions in each section and how well production personnel were managing the situation, has been used with success for some time. It was decided that a similar approach would be taken, and, as with the underground rating system, the resultant rating forms should not be aimed at rock engineering specialists only but should be able to be used by production personnel as well. This paper discusses the highwall risk rating method as evolved over a couple of years and highlights that it is a flexible tool that can easily be changed to suit an individual mine's requirements. It also shows how operational aspects are being measured to determine how well the identified hazards are being managed. Allied to the method is a relatively easy, and certainly "low capex," mapping technique which allows between 500 and 1000m of highwall to be covered in a day. Features generally recorded include lithology, bench height, work still to be completed, coal losses or "toes", presence of water, dolerite intrusions, existing and potential failures, prominent joints, declared special and cautionary areas, cracks on upper benches and condition of spoil piles. Highwall mapping and photography as well as basic geological data collection, enable highwall risk and operational ratings to be determined. The same rating sheets may also be completed by production personnel, but without detailed mapping.

Jan 1, 2002

By B. T. Wells

This work concerns the stress fields encountered around mining tunnels. A critical review is undertaken of the various analytical assessments of the support requirements for mining tunnels. Comments are made regarding degree and type of support together with method and timing of installation. The results have been used to indicate the type of support required in different mining and geological conditions.

Jan 1, 1981

By D. J. Reddish

This paper illustrates how numerical modelling has been utilised to predict water and gas pathways around active longwall panels using two case studies. This information has proved invaluable m the design of methane drainage schemes and for risk assessments undertaken at the mining planning stage. The modelling approach described has now been applied successfully to several situations in UK coalmines in order to optimise the position, length and orientation of methane drainage boreholes. The first case study describes the numerical modelling of the stress and shear plane development mund a longwall panel. The simulation was used to predict potential gas pathways through regions of low stress confinrment which are conducive to fluid flow. The conclusions from the modelling were utilised to allow an increase in the volumes of gas drainage and allow the efficient mining of the panel. A detailed discussion is provided on the model construction, determination of input paramters and optimisation of the borehole positions Details are provided on how the models allow a prediction of the fracture patterns, stress distributions and zones of reduced permeability around an active longwall panel. The second case study describes the numerical modelling of a fault adjacent to a face line drivage of a panel that had just started to be retreated. An inrush of water had occurred and a concern was whether further mining would lead to more extensive inrushes or whether the water inrush was associated with more local, limited capacity water bearing features. The role of a fault that was positioned close to the locality of the mine workings was examined. Fracture patterns stresses, strata permeability and water flows were predicted using mechanical and hydro-mechanical coupled models.

Jan 1, 2003

By Maynard O. Serbousek

The mechanics of load transfer of fully-grouted roof bolts in coal mines has been investigated in laboratory and analytical studies. The purpose of this research is to increase the understanding and better interpret data from pull tests which are routinely performed in the field. Laboratory work includes variation of bolt length, hole diameter and grout type in pull tests. Four-foot bolts were tested in holes of 1- and 1-3/8-inch diameters. Both polyester resins and inorganic grouts were used as the anchorage medium. The bolts were strain gauged at six locations to observe the rate of load transfer from the bolt to the rock mass when a force was applied at the bolt end using standard Jack pull testing procedures and equipment. Analytical studies using closed form solutions and finite-element techniques were compared to experimental results. The models are for the elastic regime only but do include slip elements. A detailed analysis of the load transfer mechanisms from the bolts through the grout to the rock mass is presented.

Jan 1, 1984

By John C. Stankus

ldentifcation of potential roof problems in coal mines has long been a complex issue due to the wide variety of mining and geological conditions. It is well known that mine roof falls are related to many different factors such as roof strata properties, sandstone channels, regional and localized horizontal stress, vertical stress, and tectonic stress. Many times, a combination of these factors causes roof problems. Through years of ground control experiences, Keystone Mining Services LLC, (KMS) has developed a Roof Instability Rating (TUR) system to predict potential roof problems. The first RIR analysis was presented at the 19th Ground Control Conference (Watts, et al., 2000). The RIR system includes: quantifying each individual factor, weighting each factor, combining individual factors, finalizing the RIR, and setting the criteria for the areas where special support is needed. In this paper, the application of the Roof Instability Rating (RIR) system at Enlow Fork mine will be presented.

Jan 1, 2001

By Peter Cain

Twenty years of research into the design of permanent gateroad support (packs) in coal mines have resulted in two methods of pack design based on engineering principles. The first, the detached block concept, is based on static loading of the support system by an hypothetical detached block. The second, the roof beam tilt concept, is based on the dynamic loading of the support system as the roof beam tilts over the roadway about a pivot point located in the rib-side. The roof beam tilt concept has been used on a number of occasions to design packs in a variety of conditions. However, recent work in the Sydney Coalfield of Cape Breton Island, Nova Scotia, has shown that design criteria based on the roof beam tilt concept in its present state of development are far from universal in application. After a review of published pack performance data, including detailed studies conducted in the UK, France and Canada, it was found that consideration of the mechanical properties of the roof beam produced a design criterion that fitted the available data. Modifications to the design process using the roof beam tilt concept are suggested for use in pack design. The work also revealed that current research in other aspects of coal mine ground control, particularly the areas of powered support design and subsidence prediction, may provide valuable information leading to major advances in this field. Such developments could also extend the application of the roof beam tilt concept to the design of pillar systems.

Jan 1, 1993

By William Gray

It has been ten years since the Mine Safety and Health Administration (MSHA) promulgated a safety standard requiring the use of Automated Temporary Roof Support (ATRS) systems in underground coal mines. The use of ATRS systems with roof bolting machines and continuous miners equipped with integral bolters has all but eliminated fatal roof fall accidents associated with manually setting temporary roof support. The last ten years have seen an evolution of the ATRS systems themselves and of MSHA's policy regarding ATRS systems. These changes are a response to operational and safety issues regarding ATRS systems often brought about by the ever-changing coal mining environment. As a result, MSHA's Technical Support personnel receive numerous inquiries from all segments of the coal mining industry on various ATRS topics. These requests for technical assistance range from an interpretation of a facet of the ATRS standard to an in-depth evaluation of a prototype ATRS system. This paper will address the aforementioned evolution of ATRS systems and will also summarize the factors MSHA Technical Support uses to evaluate these systems in the field. In addition, some of the more common misconceptions regarding the design, use, and regulatory requirements regarding ATRS systems will be covered.

Jan 1, 1998

By Thomas M. Barczak

A theoretical evaluation of the impact of horizontal load on shield support capacity is made from a static rigid body analysis of the shield structure. Parameters affecting horizontal support resistance are investigated for a typical too-leg shield design. Horizontal forces acting on a roof support element are found to be both roof-generated and shield-generated. The impact of shield-generated horizontal forces on roof strata is also discussed from a theoretical viewpoint in relation to desired ground control. A technique is described whereby horizontal loading of shield supports can be measured underground. Horizontal load measurements from two different longwall faces were found to be significant, ranging from 20-35 pct of measured vertical load.

Jan 1, 1984

By Krzysztof Tajdus

In Europe, horizontal strain is a primary parameter for estimating building hazard resistance. Other measured indices, like curvature, are less important, since in most cases of European excavation depths are very large (about 1,000 m (328 ft)) and, in such circumstances, curvature influence decreases. Therefore, a proper description of horizontal displacement (and strain) in the scope of minimizing influence is essential. This article presents a development of European methods of horizontal displacement and horizontal strain calculations, as well as current solutions in this respect.

Jan 1, 2011