Search Documents

By S. K. Nicol

The results of column flotation tests conducted on a bulk sample of ultrafines discarded from the fine coal desliming cyclones at the Riverside coal preparation plant of Theiss Dampier Mitsui Coal Limited are presented. A 9% ash concentrate was obtained from a 51% ash ultrafine feed at 75-80% recovery of combustibles in a single stage of column flotation. From this result it is predicted that installation of column flotation at Riverside would lead to the annual recovery of additional coal worth $US5.1M. The operating conditions for coal and copper column flotation are compared and some differences which may result in a variation in column design are noted.

Jan 1, 1987

By Ernest E. Thurlow

The Geology Division of Northern Pacific Railway Company has adapted to its exploration efforts field procedures for geochemical sampling and semi-quantitative analysis which have been developed through research by the U. S. Geological Survey. The sampling is done in conjunction with reconnaissance geologic mapping on aerial photographs or during field checking of maps which have been prepared largely by photogeologic interpretation.. Stream sediment or soil samples are taken and readily soluble combined heavy metals are extracted with ammonium citrate followed by colorimetric titration with dithizone at the sample site. The effectiveness of this approach has been demonstrated both in positive and negative results, thereby assisting in the elimination of large areas of land from further immediate attention and in providing targets for followup exploration. An occasional sample is submitted for spectrographic analysis as a check on the possible presence of other elements of economic significance. Field laboratory procedures are also being implemented for determining molybdenum, mercury, and other metals which may be valuable in themselves or useful as pathfinder elements in outlining mineralized areas. A lead-zinc occurrence in Oregon and a copper deposit in Montana were readily detected and outlined by stream sediment and soil sampling and a heavy metal anomaly that lacks obvious interpretation has been found in northwestern Montana. Detailed mapping and additional sampling are followed by other exploration techniques if warranted.

Jan 1, 1964

By Bo Hyun Kim, Mark K. Larson

Researchers at the National Institute for Occupational Safety and Health have tested the finite element code, UT3PC, with LaModel to evaluate their results using know case studies. The purpose of the testing was to demonstrate the usefulness and limitations of these programs in evaluating mine layout design. Both of these software packages are simple to use and free for public download. Their use by mine engineers, along with other tools, such as empirical methods, can enhance the assessment of a mine layout design. LaModel can model mining layout on a mine scale or, at least, on a multiple-panel scale. However, this software has limitations in calibrating to conditions at many coal mines in the western United States. The UT3PC software models smaller parts of a mine and is used to evaluate the design of pillars, shafts, or drifts; but the software calculates all components of the stress tensor and provides stresses, displacements, and safety factors throughout the model volume. The two codes are used to evaluate design of one known case, and UT3PC is used to evaluate another case. The results and approaches demonstrated in the testing are intended to aid mine engineers in evaluating site-specific problems and to show that these tools can provide useful information to the mine engineer in evaluating mine layout design.

Jul 1, 2023

By R. M. LaDouceur, C. A. Young, W. Nicholas

"Salicyl hydroxamic acid (SHA) adsorption on two rare earth oxides, lanthanum and yttrium, was studied. Adsorption at both surfaces occurred in two stages. Initially, the monovalent anionic collector appears to adsorb significantly and instantaneously in stage one and then becomes sluggish in stage two presumably because the initial stage passivated the surface. By comparison, adsorption during the sluggish second stage with lanthanum oxide did not stop but with yttrium oxide essentially stopped. Surface monolayer formation could not be observed in either of the two cases. Both stages appear to be due to multilayer formation of a surface precipitate as proven by Raman Spectroscopy for lanthanum oxide but inferred for yttrium oxide. Unlike the use of octyl hydroxamate as stated in the literature, increasing temperatures do not increase adsorption such that flotation of rare earths with SHA may be performed at room temperature leading to improved recoveries as well as significant energy savings. INTRODUCTION Rare Earth Elements (REEs) are comprised of the 15 lanthanides along with scandium and yttrium. The REEs with lower atomic numbers are relatively more abundant and are categorized as light REEs. On the contrary, the REEs with high atomic numbers are less abundant and referred to as heavy REEs. They are not really “rare” and, in fact, some of them are quite abundant in the Earth’s crust; it’s just that they “rarely” exist in concentrated deposits but rather are found dilute and practically everywhere. REEs share very similar physico-chemical properties but, because many of these properties are unique, they have gained enormous importance in recent times making several critical and strategic pending their use. For example, REEs have found extensive application in phosphor coatings, magnetics, and automobile cracking catalysts. Early technology was not advanced enough to produce commodity level production of the REEs and can be attributed to REE-bearing ores containing many rare earth minerals (REMs), not just one. In this regard, there are numerous REMs but bastnaesite, xenotime and monazite are considered to be the most common. Bastnaesite is a fluorocarbonate whereas the other two are phosphates. The separation of the individual REE-bearing minerals from the ores is not an easy task since they also exhibit very similar properties. Consequently, when flotation is used, it is done to produce bulk REM concentrates. For REM flotation, it is well established that octyl hydroxamate is more selective than fatty acid collectors (Pradip and Fuerstenau, 1983 and 1991). Liu et al. (2006) indicated that hydroxamates are the most common collectors for REMs. Pavez et al. (1996) studied the adsorption of oleic fatty acid and octyl hydroxamate on REM surfaces. Cui et al. (2012) studied the interaction of octyl hydroxamate with various REMs surfaces using various spectroscopic techniques such as XPS, FT-IR and Raman along with electron microscopy and concluded that such techniques offer ample information to establish adsorption mechanisms. Ren et al. (1997) studied napthalenic hydroxamic acid as a unique collector for flotation of REMs from bastnaesite ore and indicated that more selective collectors were needed. From these studies, it is clear that the quest of more selective collectors is essential but understanding how they adsorb at mineral surfaces is prerequisite to improving flotation performance."

Jan 1, 2016

By J. H. Field

The sulfur dioxide emitted in low concentrations in flue gases from the combustion of sulfur-containing coals and fuel oils is a significant factor in contamination of the atmosphere with sulfur dioxide. A review of methods for treating gases containing high concentrations of sulfur dioxide shows that they are seldom satisfactory for purifying flue gases. Processes developed specifically for treating flue gases using liquid absorbents are costly and may cause localized pollution, because the cooled flue gases can settle in the vicinity of the stack. Bench-scale research is being conducted to investigate the use of dry absorbents for sulfur dioxide removal at temperature levels of about 250°- 300° F. and 600°-650° F. Alkalized alumina has been found effective for treating simulated flue gas and Is regenerable by hydrogen, carbon monoxide, or producer gas. Other metallic oxides have been tested as absorbents also. Chemically impregnated activated carbons removed sulfur dioxide from the gas at 265° F. Vanadium pentoxide is effective as a catalyst for oxidizing of sulfur dioxide in the simulated flue gas at temperatures lower than have been used commercially for gases with higher concentrations of sulfur dioxide. Conversions of sulfur dioxide to trioxide wore studied as a function of temp- erature over a range of about 570° to 750° F.

Jan 1, 1959

By N. Sahin, M. Can, Z. Ekmekçi, Y. Öztürk, Ö. Biçak, I. B. Çelik, B. Kocabiyik

"In this paper, a case study from Çayeli Bakir Isletmeleri A.S. (Rize, Turkey) about the selective flotation of copper minerals from sphalerite is discussed. Çayeli Cu-Zn Sulfide Ore contains different ore types, such as yellow ore, clastic ore, bornite-clastic ore, bornite-yellow ore, and black ore. For some of these ore types, selective flotation of copper and zinc is very difficult presumably due to presence of secondary copper minerals such as bornite, chalcocite and covellite, and also surface oxidation. These factors affect Cu-Zn selectivity due to activation of sphalerite particles in the ore during the process. The main objective of this work was to improve Cu-Zn selectivity by optimization of the pulp chemistry for different ore types of Çayeli ore. After preliminary flotation tests investigating effects of different chemical conditions, a plant survey was performed to determine the plant performance and sources of the problems when problematic bornite-clastic ore is treated in the plant. Various chemical conditions are tested in the laboratory scale test for better depression of sphalerite in copper flotation circuit. Combination of Na2S+ZnSO4+MBS was found to be the most effective depressant scheme. INTRODUCTION Ore variability is one of the most important factors affecting performance of a process plant both in short and long term planning. The geometallurgical modelling becomes a common tool to determine ore variability problems and develop the most efficient solution during life of mine (1, 2). Flowsheet design and equipment selection and sizing are usually done based on the results of ore variability test works. However, in some cases ore variability may not be foreseen during the design stage and therefore the solutions should be developed based on the existing flowsheet and equipment in the plant. In this situation, ore characterisation, problem statement and diagnostic testing should be applied step by step. The problem could be due to changing feed grade, mineralogical characteristics, grindability and surface characteristics when flotation is involved. The variability in feed grade with fixed mineralogy can be handled with relatively simple modifications (i.e. adjusting throughput or equipment capacity) in the plant. Variability in ore mineralogy is the most complex and difficult problem to tackle. Because, mineralogical variations could bring variations in mineral composition, texture and liberation. These variations can potentially lead to the variations in grindability of the ore and flotation behaviour. Variations in grindability are usually managed by optimization of operational parameters in grinding circuit, as it would be costly to replace the existing equipment in the circuit (3). The variations in flotation behaviour are mainly due to variations in mineral types and distribution, texture and surface oxidation. One or all of these factors could be observed in a flotation operation. Therefore, a comprehensive investigation both in plant and lab scale should be conducted for definition of source of the problem. The testwork to solve the problem and retrieve the performance is planned and conducted depending on the source of the problem (4, 5)."

Jan 1, 2017

By C. Bateman, F. Calizaya

"This study presents the results of three laboratory experiments on pressure balancing carried out at the University of Utah’s coal mine ventilation model. The model includes simulations of two working areas, one longwall mine gob, and a set of stoppings and seals. It also includes a pressure chamber between the longwall face and the gob. The model is ventilated by one main fan and one bleeder fan. A carbon dioxide injection system, equipped with flow control valves operated by a microprocessor, is used to pressurize the chamber and to maintain the pressure in the chamber slightly higher than that of the gob. During each experiment, fan pressures and stopping resistances were changed, the carbon dioxide injection rate was regulated, and the differential pressures across the stoppings were monitored so that the chamber pressure is always kept slightly higher than that the gob pressure. Result of these experiments are reported in this paper. INTRODUCTION Spontaneous combustion (Sponcom) is a safety hazard in underground coal mines. The history of coal mining in the US is replete with mine fires and explosions. Sponcpm accounts for approximately 17% of the total number of fires recorded in the U.S. since 1990. In the U.S., by law, worked out areas in coal mines must be either ventilated by a bleeder system or isolated by explosion proof seals. Experience has shown that seals are not airtight structures and that they allow some leakage of air into or out of the gob. In fact, seals “breathe in and breathe out” with changes in barometric pressure (Francart 1997, and Chalmers 2010). These changes in pressure affect not only the methane emission rate but also the ingress of oxygen to the gob, the lower the pressure behind seals is, the higher the ingress of oxygen. In mines ventilated by a U-tube exhaust system, the gob is often kept under negative pressure. Under these circumstances, an increase in barometric pressure may cause an influx of fresh air into the gob. This quantity may be sufficient to start self-heating of the coal, which can lead to spontaneous combustion. Depending on the coal characteristics and the ventilation conditions, self-heating of coal can start at temperatures as low as 35 ºC. If the heat is not removed it will increase the coal temperature leading to ignition and fire. The risk of Sponcom fires can be reduced by isolating the mine gob using rated seals, and implementing a suitable ventilation system. However, isolation seals are not airtight structures, thus some leakage of air is expected unless the pressure in the gob is neutralized. The alternative is to use a pressure balancing system. This requires a thorough knowledge of the ventilation system, the seal/stopping construction techniques, the airflow behavior in the gob area, and the gas build-up behind the seal line."

Jan 1, 2016

By Michael Lenz

Predictive maintenance technologies including vibration analysis, tribology, infrared thermography, ultrasonic detection, and electrical measurements have been applied to large electric mining shovels. The predictive program was initiated on the P&H Model 2300 and 4100 electric shovels. The utilization of these technologies has shown the potential for improving electric mining shovel availability and minimizing maintenance costs. Predictive technologies provide the tools to assess machinery condition. Availability is enhanced by the condition based planning of component replacement. Maintenance costs are minimized by focusing resources through condition based prioritization.

Jan 1, 1997

By D. M. Urich

This paper is a follow-up on a previous paper presented at the A.I.M.E. Meeting in Chicago, Illinois, on February 17, 1965, by Mr. D. Kelly Campbell. Mr. Campbell's paper was presented prior to the operation of the Eveleth Taconite-Company's Plant, and this paper outlines and reports on the operation and performance of the Plant after the first nineteen months of operation.

Jan 1, 1967

By S. Yerel

Block cutter machines have been extensively used in natural stone industry, which is a sub-section of mining industry. In this study, the costs occurring in plate losses cut from Bilecik beige marble with a circular saw block cutter machine have been predicted using Statistical Process Control (SPC) techniques. One of SPC techniques is Shewhart control charts such as mean control chart. These charts have been efficiently at determining the plate losses. The costs occurring in plate losses have been calculated by using the result of Shewhart control chart. Finally, this study presents the necessity and usefulness of SPC techniques in assessment of natural stone industry.

Jan 1, 2010

By Y. Akin

The floatability of a typical boron mineral, colemanite (Ca2B6O11.5H2O), is shown to be hindered by the presence of montmorillonite type clay minerals. The clay is found to act in the form of slime coating. The mechanism of slime coating is investigated using pure colemanite and clay and their mixtures with an anionic reagent in a microflotation cell. Adsorption, flotation, solubility, zeta potential and scanning electron microscope studies reveal that slime coating occurs through electrostatic attraction. It is possible to minimize the effect of slime coating either at high surfactant concentration or at high pH values.

Jan 1, 1997

By John C. Cook

There is pressing need for better means of exploring ground conditions ahead of mining. Exploration drilling has the drawbacks of high cost and a seriously restricted sampling zone. Traditional geophysical exploration methods including gravity, magnetic and resistivity techniques have been used with some success underground, but all give poor target delineation relative to range, since they depend upon minor distortions of a potential force field. Much greater ratios of resolution to range can, in principle, be obtained by employing electromagnetic or seismic radiation as the exploring agent. This is because propagation time delays can be used to measure range accurately, and to separate the small effect of a distant target from the much larger effects of nearer targets and of the transmitter. Seismic waves have long been used with great success in exploration for petroleum, and recent research on their application underground is promising. Electromagnetic (radar) waves have been very successfully used for detection and location through the air and outer space, and have also explored through polar icecaps more than a mile thick.l It is not generally realized that below the soil many rocks are also somewhat radar-transparent, and that radar can be used for exploring such rocks, once a quarry, a mine, a borehole, or other means of access has been opened. Radar waves are reflected by any boundary or object where they encounter a large change in electrical properties.2 The usual cause of such a change is a difference in moisture content. Radar waves passing

Jan 1, 1972

By Madan M. Singh

Although roof bolting has been a major means of strata support for nearly two decades, little attention has been directed towards the design of bolt Installations. The variables involved are interdependent and their study complex. However, some simple tests may be employed to serve as guides to the efficient design of roof bolt systems. Local conditions are continually varying and are important to pattern design. This paper discusses such considerations and suggests techniques which may be employed to effect improved roof control with bolts.

Jan 1, 1967

Coal-derived flue gases contain CO2/SO2 and these contaminants preferably have to be captured by cheap sorbents. This remediation approach is from the standpoint of addressing issues such as global warming, acid rain and development of Advanced Power Generation Systems and to realize the economic gain as well. Conventional and existing dry scrubbing technologies use regenerable sorbents which are pollutant specific and require expensive stabilizers in order to attain versatility. This paper discusses the use a novel class of sorbents prepared from the heavy metal contaminated Berkeley Pit water (Butte, Montana) by a proprietary process developed at The University of Nevada, Reno. These sorbents are activated mixed spinel ferrite (MxFe,_X04)' Preliminary experimental results show that the sorbents have good desulfurization and CO2 decomposition capacities. The decomposition effectiveness of these mixed spinel ferrites was studied at 300°C and compared against the synthetic magnetite obtained from ferrous sulfate solution in our laboratory. The results indicated that the mixed spinel ferrite had good affinity for the adsorption and decomposition. The CO2 decomposition data of both sorbents fitted the first order reaction kinetics. Even though the surface area of the magnetite was higher than that of mixed spinel ferrite, the CO2 decomposition rate of the mixed spinel ferrite was estimated to be 2.5 times higher than that of magnetite under identical conditions. The carbon analysis deposited on the sample indicated that the CO2 was 100% decomposed into carbon and other carbon! hydrogen compounds by the mixed spinel ferrite whereas the conversion was 43% by the magnetite. In terms of specific adsorption of carbon, ferrite was 3-5 times more efficient than magnetite.

Jan 1, 1996

By R. D. Lopez

The concept of "heat recuperation" for the grate-kiln pelletizing system was first implemented at the Sydvaranger plant in Norway in 1974. Essentially, heat recuperation involves bringing hot air from the second stage of the pellet cooler to the drying zone to increase drying-air temperature to the maximum limit. 'Burner-fuel savings result from a lower kiln secondary-air mass flow at a higher temperature. Because of the fuel benefits achieved at Sydvaranger, heat recuperation has been included innumerous new grate-kiln plants built since then, and some older plants have been retrofitted for heat recuperation. In recent years there has been much confusion about the fuel benefits of heat recuperation. To answer some of the questions, a mathematical model was developed and plant tests were conducted at Minntac Phase 111. Minntac is a magnetite taconite concentrating and pelletizing plant, and Phase III has two indurating lines. This paper presents the results of the studies and plant tests.

Jan 1, 1980

By T. D. Wheelock

The effect of various flotation depressants and surface treatments on the floatability of coal derived pyrites in the presence of XIBC was investigated with a modified Hallimond tube microflotation cell. The floatability of pyrite particles which had been cleaned with hot dilute (5%) hydrochloric acid was relatively large. However, the floatability of such particles was reduced greatly by the addition of specific depressants such as calcium hydroxide and also by treating the pyrite with an aerated warm alkaline solution. Although this treatment and these depressants also had some effect on the floatability of coal particles, the effect was much less than on the pyrite particles.

Jan 1, 1979

By V. Rajaram

The Parachute Creek Member of the Green River Formation in the Piceance Basin, Colorado, contains vast reserves of oil shale, nahcolite, dawsonite, and other accessory minerals. The dry alkali process of sulfur dioxide removal using nahcolite (naturally occurring sodium bicarbonate) has great potential. A room and pillar mining scheme has been designed to extract a nahcolite zone occurring at a depth of 472 m, from the lease application area of the Yankee Gulch Joint Venture. Geotechnical parameters affecting mine design will be discussed. A preliminary development plan for mining at the rate of 1000 t/d will be described in detail.

Jan 1, 1977

By Robert M. Becker

The evaluation of in situ rock stresses from measurements of the change in diameter of a borehole that is stress-relieved by overcoring has become a common practice. Generally the stress evaluation has been based on isotropic relations whereas rock in varying degrees is anisotropic. A plane elasticity solution for a circular hole along one axis of an orthotropic medium has been adapted to evaluation of in situ stress. The necessary elastic parameters for this evaluation may conveniently be obtained from static tests on the overcore in conjunction with a consistent orthotropic thick-wall cylinder solution. The method and equations for the laboratory and field evaluations are summarized and illustrated.

Jan 1, 1968

By Kevin Hegerle

The Henderson Mill has operated over a wide range of production rates, feed grades, manpower levels and recovery targets since start-up in 1976. Henderson Mill personnel, both management and hourly, have successfully responded to these changes by not only maintaining unit costs, but by actually decreasing unit costs. Methods of cost reduction have included conventional austerity programs, innovative technological improvements and creative work schedules. This paper addresses both maintenance and operating cost reductions and efficiency improvements.

Jan 1, 1986

By C. E. Capes

The continuous balling? operation whereby a moist particulate mass is tumbled in a horizontal revolving drum with recirculation of the undersize product can be extremely unstable. Product and recycle rates are subject to wide fluctuations. Although the problem seems to be well-recognized, there is little published information or quantitative data readily available, especially in relation to industrial-scale circuits. Probably the best available published results are in the Russian literature, an illustration of which is given in Figure 1. These data, taken from a study') of some of the factors which influence the stabilization of the pelletizing process, illustrate the wide variations in circulating load and circuit productivity which may be encountered over a period of operation. The problems of balling circuit stability may be traced to random seed or nuclei generation and uncontrolled agglomerate growth. The situation is analogous to that in crystallization processes where (4 considerable attention is given to nucleation control. Traditionally attempts have been made to optimize system and operating variables to stabilize the balling process. A supplemental approach which is taken here is to build on the considerable

Jan 1, 1975