Search Documents

By N. Edmonson

Introduction An examination of statistics for the world phosphate fertilizer industry since 1980 reveals that there is an increasing tendency for fertilizer-manufacturing activity to concentrate in the areas of phosphate-rock mining. The economic justification for this resource-oriented strategy is clear. The choice between shipping phosphate rock, a comparatively low-value product, and shipping a more valuable finished fertilizer product will always, as long as cost considerations control the decision, be resolved in favor of the latter. The historical existence of substantial phosphate fertilizer-manufacturing capacity, which is oriented toward fertilizer-consuming activities and dependent on imported phosphate rock, shows that narrow cost considerations have not always determined the industry's location. One is entitled to ask what conditions have changed to precipitate the observed relocations, and how permanent are these changes. These questions are the subject of this investigation. Recent trends in world phosphate trade Since 1980, the changing pattern of world trade in phosphate materials reflects an increased interest in manufacturing phosphate fertilizer in rock-producing areas. This is shown by the decline in the total tonnage of phosphate rock being traded worldwide compared to world consumption of phosphate fertilizers (Fig. 1). This relative decline has continued since 1984, which is a longer period of time than could be explained by temporary cyclical market factors. Other evidence corroborates this conclusion. The world's phosphate-rock production is relatively concentrated geographically. In 1992, the top ten producing countries accounted for 92% of world production. Figure 2 shows that the share of world fertilizer production in the top ten rock producers has increased. Yet, further evidence of the direction of trade changes can be had by looking at the pattern of the world's sulfur trade. The first step in the manufacture of any of the widely used phosphate fertilizer products is the acidulation of phosphate rock with sulfuric acid. In most instances, phosphate fertilizer producers have found it economical to produce their own sulfuric acid by burning elemental sulfur, and such operations account for over 60% of all sulfur consumption in the world. 1 Therefore, a concentration of phosphate fertilizer production in rock-producing countries should produce a similar concentration of sulfur imports in the same countries. Figure 3 suggests that there has been a tendency since 1989 for sulfur exports to go increasingly to the rockproducing countries. World phosphate-location strategy is not limited to the alternatives of shipping rock and shipping finished fertilizers. A third alternative consists of producing phosphoric acid, the principal phosphate fertilizer intermediate, at the rock deposit, and then exporting it to market-oriented ammonium phosphate plants. This arrangement offers the importing country the advantages of shipping a more concentrated product while retaining the economic multiplier benefits of a domestic high-analysis fertilizer industry. India, and several other countries, imports merchant-grade phosphoric acid to use as input for the domestic value-added fertilizer industries. For various reasons, the trade in phosphoric acid has never quite lived up to the promise suggested by the foregoing discussion. Figure 4 shows no growth in this trade in the last ten years, either in absolute terms or in relation to the world's consumption of phosphoric acid. Most of the decline in the trade in phosphorous in rock form has been replaced with trade in finished fertilizers. The trade in superphosphoric acid was a growth activity in the late 1970s with the growth in US exports to the USSR, and this trade survived the Carter-era embargoes of US-Soviet trade. However, no additional sizable markets for superphosphoric acid developed, and other suppliers sought out the Soviet market. The problem with superphosphoric acid is that the cost of its incremental concentration is as great as the savings from shipping the more concentrated product. The Soviet market was a special case. The political breakup of the Soviet Union disrupted the superphosphoric acid trade after 1991 and led to a shutdown of the US export capacity.

Jan 1, 1996

By Nomuqhele N. Nkosi, Yasuo Yabe, Musa D. Manzi, Raymond J. Durrheim, Siyanda B. Mngadi

This study examined rock failure in brittle rocks hosting the deep gold-bearing ore bodies on scales between millimeters and kilometres. This research study is part of the International Continental scientific Drilling Program (ICDP) project, “Drilling into Seismogenic Zones of M2.0-M5.5 earthquakes in deep South African gold mines” (DSeis). The broader ICDP-DSeis project aims include the examination of the extent of damage, the stress state around the fringes of the earthquake, and the potential existence of living organisms associated with deep-level earthquakes. Nevertheless, this study focused on two seismogenic zones – the Cooke 4 mine and Moab Khotsong mine. At Cooke 4 mine, the study examined the evolution of mining-induced fractures (M1-4) occurring ahead of the stope face during the extraction of the remnant shaft pillar. These fractures were monitored and delineated by a dense array of acoustic emission sensors that allowed hypocentres to be located with decimeter accuracy. Using this acoustic emission data, the DSeis team drilled and recovered the fractures, rock breccia and gouge using a sophisticated triple-tube drilling rig.

Apr 26, 2022

By Z. Rogovin

A Knowledge of the amount of time the material spends in a continuous mill in a closed-grinding-circuit is essential for circuit performance analysis and scale-up design. A convenient method for acquiring this information involves the use of tracers in residence-time-distribution (RTD) experiments. In a typical wet process the RTD measurements are usually done by injecting a pulse tracer into the mill inlet and detecting it in the circuit exit. In this article a simple to use mathematical method for the calculation of the closed circuit material residence time in the mill is developed. Using this method there are no restrictions on the location of the tracer injection or detection points. Any convenient location in the closed circuit can be chosen without affecting the simplicity of the method. This method also enables the calculation of the degree of mixing in the mill. The use of this method for the analysis of impulse response data obtained from several commercial grinding circuits is presented.

Jan 1, 1986

By M. Gunter, M. Buzon

"Talc formed by hydrothermal alteration of preexisting carbonate rocks is known to be nearly monomineralic, and lacking in amphiboles. In southwest Montana, talc formed from hydrothermally altered dolomitic marbles, and is still actively mined. These talc deposits are typically in contact with quartzofeldspathic gneiss and marble. Accessory minerals vary between these rocks and the ore producing body; the identification and characterization of such minerals requires carefully selected analytical methods. Recent litigation and ensuing confusion over the petrology and asbestos content of these deposits challenges the talc mining industry in Montana, and elsewhere in the world. INTRODUCTION Commercial talc has been mined from the deposits in southwest Montana since the 1940s, and by 1956 the region had output 200,000 tons of talc ore (Chidester et al., 1964). Commercial talc refers to rocks containing more than 20% of the mineral talc (McCarthy et al., 2006); the ores from Montana typically contain upwards of 90% talc. This region remains the leading domestic source of talc in the U.S. partly due to the reserves in the area, and partly due to the diagnostic purity of the ore compared to that of other regions, some of which are no longer actively mined. The mineral talc, a sheet silicate, is expressed by the formula Mg3Si4O10(OH)2, and therefore can form in geologic environments that are rich in Mg, Si, O and water. The protolith for the talc deposits in southwest Montana is a dolomitic marble, but other common protoliths include ultramafic igneous, mafic igneous, and siliceous dolomites (McCarthy et al., 2006). Physical properties such as hardness of 1 on Mohs hardness scale, white streak and slippery feel are among some of the reasons why talc is so widely used as fillers in a number of industries. In decreasing order, ceramics, paper, paint, roofing, plastics, rubber, and cosmetics are the leading domestic industries that use talc despite the decreasing trend in U.S. talc use and production since 1994 (Virta, 2015). The purpose of this paper is to describe the mechanism of talc formation in southwest Montana by focusing on talc deposits and surrounding rocks in the Ruby, Greenhorn, and the Gravelly Ranges, and to relate the mechanism of formation to the composition of talc ores. The compositional data show mineral content of selected ores, and the major and trace element content of those minerals, specifically talc. Our electron microprobe (EPMA), powder x-ray diffraction (XRD) and x-ray fluorescence data for samples from five mines in these three ranges provide continued evidence of the purity of these ores despite claims made during recent litigation that these ores contain asbestos. The five mines that we discuss include the Beaverhead, Treasure, Regal, Willow Creek, and Yellowstone Mines (Figure 1.)"

Jan 1, 2016

By W. M. Luff

The Brunswick No. 12 Deposit is a large polymetallic massive sulphide deposit, occurring in Ordovician age rocks of the Tetagouche Group. Silver is contained within the sulphide zones and economically it is the second most important commodity produced. Brunswick is one of the largest silver producers in Canada. The distribution of silver within the mine is presented, with examples from various levels. The concentration of silver can be shown to be related to both stratigraphy and structure. The mineralogy of silver in mill products is also presented.

Jan 1, 1986

By Harry G. Hedgepeth

Exploration of the Big Island trona beds by Stauffer Chemical Company started early in 1959. During the intervening time, Stauffer Chemical Company of Wyoming has developed a Large trona mine in this southwestern Wyoming area and has increased the over-all production of soda ash from natural sources by nearly one-half million tons per year. The trona, which is a hydrated sodium bicarbonate mineral, lies some 800 feet into the sedimentary rocks of the Green River formation. Present production is approximately 850,000 tons per year being extracted by means of a room-and-pillar mining system. Conventional coal mining equipment is used with some modification to accommodate local conditions. The mined and crushed ore is hoisted to the surface and processed in an on-site refinery. Refined soda ash is shipped to widely separated locations in covered hopper railraod cars. Construction in progress at Stauffer's plant will double the present capacity.

Jan 1, 1966

By N. R. Sainath

This paper discusses a laboratory investigation that studied the microscale flow characteristics of copper ores and the variation in flow behavior resulting from flow of leach solution. Fractures in 40- and 100-mm-diam (1.5- and 4-in.-diam) cores were first mapped by visual inspection. The permeability of cores to water-stressed in a triaxial stress field representative of in situ conditions - was estimated. The samples were then exposed to 20g/L (2.7 oz/gal) sulfuric acid and the experiment was repeated. The porosity and the rate of recovery of copper from the specimen during leaching were also studied. The measured permeability of unleached samples with no visible fractures ranged from 10-16 to 10-19 m2 and it increased as leaching progressed. The porosity increased significantly with leaching, while the rate of copper recovery decreased.

Jan 1, 1994

By Stephen C. Tadolini, Colton Cook, Cody Hildreth, Frederick Cybulski

"Broken and jointed ground is extremely hazardous and requires unique stabilization techniques to protect worker and critical entries. Bolting techniques, even the most advanced with pre-load to create roof compression, can leave large gaps of unconfined and separated roof. This roof can also be susceptible to water inflows which only exacerbate the support problem. These types of conditions existed on long term development main entry accessing several future longwall panels. The geotechnical assessment identified well-defined jointing systems that also permitted water to flow between the roof separations, which “lubricated” the roof material and minimized any frictional advantages. Chemical injection of a Polyurethane material, Minova Carbopur WS, was placed beyond the bolted horizon to move the water to the rib lines and reinforce the fractured and broken roof. The injection material permitted the effective use of bolting patterns and helped ensure long-term stability of these critical entries. The paper describes the evaluation techniques, design patterns, basis for chemical selection and application, and results and recommendations.BACKGROUNDThe injection of mine and underground civil structures using polyurethane (PUR) has been ongoing for over 50 years. The applications in mining have included gate road stabilizations, longwall set-up and tear-down entries, and simple consolidation of coal mine roofs. PURs have also been used for roof stabilization during longwall shield recoveries. Polyurethane injection was initially developed by the Bergbau-Forshung GmbH, a German coal mine research institute, in the early 1960s (Jankowski, 1972). The product became a standard stabilization method in Germany after its commercial introduction in 1971 (Knoblauch, 1994), and was successfully manufactured at the Minova Essen, Germany location for over 50 years. With the recent closing of the German underground mines, that manufacturing facility has been closed and moved to Katowice, Poland, where production continues today Injection products are also being successfully manufactured by Minova in Australia and the United States.Polyurethane injection in underground coal mines is used in difficult ground conditions in fractured immediate and main roofs. It is also common as a rock stabilization remedy to prevent longwall face caving during shield removal. As presented in the case study, polyurethane was applied to minimize the inflow of water from beneath a stream channel while providing reinforcement and consolidation of the fractured roof that had lost confinement. Polyurethane is a two-component system (Part A and Part B) that is injected into a borehole and can chemically bond to the rock, not relying on friction or mechanical interlock to provide support. The material is injected under pressure, coupled with a low viscosity and small particle size; it flows into roof fractures and separations, which are the paths of least resistance. New developments in low viscosity PUR materials allows penetration of cracks as tight as 0.002 inch (0.05 mm) wide. This also allows for the closures of extremely small cracks to minimize the inflow of water, even if the water is under pressure. Combinations of designed expansion properties and low viscosities make the materials ideal for minimizing and stopping flows of water from underground structures."

Jan 1, 2019

By Kenneth Denton, Michael Cutts, Andrew Bursey, Eric Eisold

Phase III of the Orme Street Combined Trunk Relief Sewer project connects two existing 2.13 m diameter combined sewers to a new 3.66 m diameter relief sewer at 7locations along a 970 m alignment in downtown Atlanta. The alignment was enveloped by adjacent structures and utilities. The project was constructed below the groundwater table through compressible residual soil, rock and mixed face using a myriad of construction techniques, including compressed air NATM and jet grouting. Numerous design and alignment changes and accommodations for existing utilities and conditions were made during construction. The authors believe this to be the ?rst NATM project in North America utilizing compressed air tunneling.

Jan 1, 2003

By R. R. Fernández

Newmont Mining Corporation has been processing refractory gold ores by roasting since January 1995. The ores are refractory due to the association of the gold with iron sulfides, namely pyrite and marcasite, and the presence of carbonaceous components and is oxidized in an oxygen-enriched gaseous atmosphere. The structural characteristics of the calcine have a strong influence on the eventual recovery of gold by cyanidation. These characteristics are strongly dependent upon the roasting conditions, mainly the roasting temperature. Originally, the sulfides and carbonaceous matter were oxidized at a temperature that typically ranged between 535 and 560 °C. Controlling the roasting temperature within the lower and narrower range of 510 to 515 °C produced a calcine with a larger surface area(e.g. higher porosity), which resulted in a gold recovery increase of3.3 percent in 2001 equivalent to 5.1 million dollars of additional gross revenue. The new strategies of operating at temperatures never tested before are discussed. It constituted a great challenge to the control room operators for the lower operating temperature falls much closer to the ignition temperature of the sulfide ore and smaller and more frequent adjustments in operating parameters were needed to improve and maintain high gold recoveries. Based on the encouraging results that were achieved in 2001, a decision was made to install a “smart” process control system because the roaster temperature control was performed by manual inputs from the control room operators. The development and implementation of the control system to reduce or eliminate the temperature variability between the different control room operators commenced in June of 2002 and was fully operational by the end of October. Lower roaster temperatures were achieved (500 to 505 °C), which resulted in further increase of gold recovery by about two percent. The overall recovery increase equated to 8.0 million dollars of additional revenue for the first 10 months of 2002.

Jan 1, 2003

By T. McCallum, C. Cooper, B. Hutzler

"In copper solvent extraction, managing the quality of the organic phase is a key parameter to ensure optimal physical and metallurgical performance in the plant. Increased throughput as a result of declining ore grades coupled with advances in plant design and practice, resulting in reduced organic losses, has pushed the limits of the status quo with respect to organic quality. Clay treatment of plant and recovered organic at the optimal dosage is critical in maintaining quality, however, achieving the optimal dosage through existing filtration capacity and practice can be difficult. Cytec has developed a process aid that increases efficiency of existing filtration equipment that has been successfully implemented at two commercial SX operations. ACORGA® CB1000 enables higher dosages of clay while allowing for more efficient use of existing filtration capacity. This study analyzes results from commercial trials and demonstrates that improved organic quality and clarity is achievable through optimization of current treatment practices. INTRODUCTION Decreasing ore grades have prompted copper solvent extraction operations to raise PLS flow rates, increasing plant throughput to maintain production1. The ability to process higher flow rates through existing mixer-settlers historically came at the expense of increased entrainments2. However, advances in mixer-settler design, practices and improvements in organic recovery processes have enabled operations to maintain, and in some cases reduce organic losses while achieving higher flow rates through existing equipment. Based on the increased demand on the SX equipment and reduced losses (or more efficient recovery) maintenance of the circuit organic quality through efficient clay treatment is now more important than ever. This paper discusses common industry practices and related issues in organic clay treatment, and presents benefits achieved in commercial operations through the use of ACORGA® CB1000 Clay Binder. IMPROVEMENTS IN DESIGN AND PLANT PRACTICE Mixer-settler design has improved since the first commercial copper SX operation in the late 1960s. Advanced designs in mixer, settler, and settler internals have contributed to reductions in entrainments. For example, improved impeller designs have been reported to decrease organic in aqueous entrainment from the ‘old designs’ of 50-200 ppm3 to as low as 4 – 10 ppm confirmed via diluent and reagent consumptions . Similarly, operations are reporting a 20-50% decrease in reagent consumption when compared to the original design criteria3. Operations have optimized settler internals to increase coalescence and have improved settler operating practices which have been shown to reduce entrainments7. Comparison of the SX world operating data from 1999 and 2007 shows reductions in organic entrainment losses with increases in flow rates."

Jan 1, 2015

By James M. Barker

Marketing is the linchpin of the industrial-mineral (IM) industry. Without markets and consumers for IM products, all other associated IM activities are superfluous. The simple existence of an IM deposit does not mean that it can be exploited. A dynamic interaction between exploration (geology), mining, processing, transport, marketing, sales, and consumers is required for profits. Geology dictates the existence of a deposit, but markets dictate its development, and transportation provides the connection. This is true to such an extent that marketing commonly is called the exploration phase of IMs. Marketing is strategic and includes long-range market-development and planning activities, whereas selling is tactical and more focused on day-to-day consumer interactions. Each will help the other when properly done. Many producers of IMs have failed because of inadequate marketing skill, information, and practice. Over many years at the Montana Bureau of Mines, the many developers seeking technical assistance to find an IM deposit, but who had no marketing plan, always failed. In contrast, the few who sought assistance first on marketing, with the IM deposit to be found later, always succeeded (Richard Berg, personal communication, 1998). Marketing has many facets helped by geologists who must be aware of what marketing is attempting to do. A geologist needs to understand many aspects of IMs: location (deposits, plants, consumers), processing (specifications), transportation (truck, rail, barge, ship), competition (local, regional, national, international), substitutes, pricing, and new developments and market forces of all kinds. Some needed skills are not taught formally to geologists, so well-rounded self-education and on-the-job training are the way a geologist normally enters into IM marketing. The IM geologist generally is associated with marketing either by helping to prepare a market study or by acting on the results of one. Preparing a market study is a two-part process. The first part is relatively simple but requires a time-consuming collation of data into an IM survey (mostly past-and present-oriented). The more difficult and much more important second part entails expanding the IM survey into a market evaluation (mainly future-oriented) that emphasizes forecasting, timing, location, and specific products. A market evaluation generally boils down to formulating the right questions to ask of the right persons. One very good question to ask is, "What could be the market for this specific IM?" while thinking for yourself without excessive recourse to gossip, rumors, promoters, developers, or (at times) IM experts. The evaluation must prove that market potential exists and suggests a marketing plan. Effective marketing is an ongoing process, with the initial marketing plan modified over time, using wide and continuous input to avoid tunnel vision. Industrial-mineral markets are based either on commodity (lower-priced, basic-processing) minerals or specialty (higher-priced, value-added) minerals. IM marketing methods are either product-driven (commodity minerals), a more traditional approach, or market-driven (specialty minerals), but these are neither mutually exclusive nor is one always better than the other. Focusing too much on specialty minerals can lead to problems. A blend of commodity products with specialty products commonly lowers risk and enhances long-term profits. The highest profits occur in specialty minerals at the cost of higher risk and complexity and require intelligent marketing, versatile technical services, and creative research and development. Industrial minerals are best served by an industrial-marketing approach rather than a consumer approach. Modern industrial marketing emphasizes the consumer using the "marketing concept." The marketing concept focuses all management and operational activities on total consumer management and satisfaction similar to the total quality management approaches to excellence.

Jan 1, 1999

By Richard L. Ash

Usually stresses generated by explosive charges during blasting are considered to propagate through materials in a spherical manner. Although conical stress-waves had been suggested by a few investigators they have never been clearly defined or critically observed. An experimental technique using models and lengths of Mild Detonating Fuse was developed to produce conical stress-waves and study their effects. Several materials with different properties were tested to compare the influence of those properties on wave shape and crater formation. The investigations showed that whenever column charges were end-initiated, conical stress-forms were produced if the explosive's velocity exceeded the energy propagation velocity of the surrounding material. The stress-cone angle significantly affected fragment size and shape as well as the geometry of craters produced.

Jan 1, 1967

By D. M. S. Bhatia

The intimate association of iron formation and massive sulfide deposits has been documented by many investigators (McAllister, 1960; Hutchinson, 1972). In a classic example of such an association four distinct facies (oxide, carbonate, silicate, and sulfide) were identified in an Algoma type iron formation occurring in Paleozoic rocks, but exhibiting physical features (banding) and chemical composition (SiO2 + A1203 + Fe2O3) typical of Precambrian iron formations. The geochemical variation of the iron formation was studied by analyzing 62 samples for Si, Al, Fe, P, S, and CO2. Following a model proposed by James (1954), the geochemical and mineralogical variation of the iron formation can be used as an excellent tool for the exploration of massive sulfide deposits.

Jan 1, 1981

By J. E. Urosek

The Mine safety and Health Administration (MSHA) formed the Mine Ventilation Bleeder and Gob Training Committee in 1993. This committee was charged with developing a training course designed to enhance the knowledge and understanding of practical bleeder ventilation systems. The course will probably include a discussion on the theory behind bleeder system design, an in-depth look at the strengths and weaknesses of the basic bleeder system types, case studies, and a review of the systems currently in use. A database on active underground bituminous coal mines, gob areas, and the bleeder systems presently used was developed from questionnaires distributed to nine Coal Mine Safety and Health (CMS&H) districts. Representative systems were selected for thorough investigation to develop case studies. This paper introduces some of the material to be included in the course, including a description of basic bleeder system designs, a review of a portion of the database, and facts about the gob areas and bleeder systems investigated for the development of case studies.

Jan 1, 1995

By William E. Horst

Ore grindability data based on various techniques to measure comminution characteristics are used to evaluate the crushing and grinding efficiency in mineral processing operations. The importance of achieving improved comminution efficiency, in terms of energy consumption, has been emphasized by recent increases in the cost of electricity. From a theoretical standpoint, the objective of a grinding operation might be expressed as maximizing the production rate at a given grind size while minimizing the energy consumption per ton of material ground. To achieve this objective in an industrial operation presents a challenge especially in view of changes in the raw material which are normally encountered. Various procedures1-5 used to determine energy-size parameters and grindability measurements have been reported. The proposed relationships between particle size and energy consumed have much in common between many of the techniques for measuring grindability. Probably the most widely used parameter to measure ore grindability in recent years is the Bond work index6, Wi, which is defined as the kw-hr per ton required to break from infinite size to a product size of 80 percent passing 100 microns. If the breakage characteristics of a material remain constant over all size ranges, then the calculated work index would be expected to remain-constant since it expresses the resistance of material to breakage. However for most naturally occurring raw materials differences exist in the breakage characteristics depending on particle size, which can result in variations in the work index depending on grind size. Consequently work index values are generally obtained for some specified grind size which typifies the comminution operation being designed or evaluated.

Jan 1, 1975

By Steven J. Schatzel, Kayode M. Ajayi, Zoheir Khademian

The integrity of unconventional shale gas well casings positioned in the abutment pillar of a longwall mine could be jeopardized by longwall-induced deformations. Under such scenarios, the surrounding fracture networks could provide pathways for gas flow into the mine creating safety concerns. To provide recommendations for developing guidelines that ensure a safe co-existence of longwall mining and unconventional shale gas production, this study evaluates the impact of parameters that could affect potential shale gas flow into the mine in the event of a casing breach using a discrete fracture network (DFN) model. These parameters are evaluated using a conceptualized DFN realization that is representative of the fractured zone in the overburden, and the range of parameter variations is within values validated with field measurements. The results show that a decrease in fracture aperture (potentially due to longwall-induced stress in the likely vicinity of the breach location) reduces the potential gas flow to the mine by a significantly higher proportion. A 50% decrease in the aperture of the fracture that directly transports the gas from the casing breach location reduces the gas flow to the mine by over 70%. Similarly, changes in the fracture water saturation level significantly affect the gas flow. In all cases, the potential gas flow to the mine is higher if the casing breach occurs at an increased gas well pressure. These findings provide critical information regarding the impact of each of the parameters associated with gas flow in the event of a shale gas casing breach near a longwall mine and could help towards the development of guidelines to ensure a safe coexistence of both industries.

Sep 28, 2022

By Simon W. Houlding

This paper summarizes recent developments in computer modelling and estimation technology. Significant improvements in computational and modelling efficiencies have advanced technical computing to the stage where, for the first time, it can be realistically applied to short-term mine planning and production control. Real-time interactive grade estimation of complex shapes, volumes and grade distributions, based on immediate turn-around of production sample grades, is now possible. An added benefit is the ability to produce complete geostatistical estimates which include confidence limits. These can be incorporated into the decision making and risk assessment processes of production control. Why the need for new technology? What is wrong with the conventional methods which have sufficed for the last thirty years? The response is manyfold. They suffer from inefficient computational processes and conflicts with geostatistical theory. They are responsible for constricting the flow of information between the disciplines involved in the mine production process. Finally, it is illogical to approximate irregular geological and mining volumes with orthogonal sets of rectangular blocks. Geological materials do not occur in block formation; and mining methods which excavate rectangular blocks have yet to be developed. Other computer based technologies have evolved out of the dark ages of rectangular approximations and have successfully dealt with irregular three-dimensional geometries. It is time for computing in the mining industry to follow this example and take full advantage of available technology. To provide the necessary background, consider the basic requirements for successful implementation of technical computing within the mine production process.

Jan 1, 1992

By S. J. Schatzel, K. M. Ajayi, Z. Khademian

The integrity of unconventional shale gas well casings positioned in the abutment pillar of a longwall mine could be jeopardized by longwall-induced deformations. Under such scenarios, the surrounding fracture networks could provide pathways for gas flow into the mine creating safety concerns. To provide recommendations for developing guidelines that ensure a safe co-existence of longwall mining and unconventional shale gas production, this study evaluates the impact of parameters that could affect potential shale gas flow into the mine in the event of a casing breach using a discrete fracture network (DFN) model. These parameters are evaluated using a conceptualized DFN realization that is representative of the fractured zone in the overburden, and the range of parameter variations are within values validated with field measurements. The results show that a decrease in fracture aperture (potentially due to longwall-induced stress in the likely vicinity of the breach location) reduces the potential gas flow to the mine by a significantly higher proportion. A 50% decrease in the aperture of the fracture that directly transports the gas from the casing breach location reduces the gas flow to the mine by over 70%. Similarly, changes in the fracture water saturation level significantly affect the gas flow. In all cases, the potential gas flow to the mine is higher if the casing breach occurs at an increased gas well pressure. These findings provide critical information regarding the impact of each of the parameters associated with gas flow in the event of a shale gas casing breach near a longwall mine and could help towards the development of guidelines to ensure a safe coexistence of both industries.

Mar 2, 2022

By P. J. M. van Heteren

The flotation system is usually distinguished from other physical chemical systems by the importance of interactions at the solid-liquid and solid-gas interfaces. In recent years, numerous quantitative studies have been made of the distribution of common collectors between the solid and aqueous solution phase. Although in flotation the main emphasis is placed on the adsorption process, chemical reactions will also take place in the bulk solution phase, These side reactions are often undesirable and will contribute towards the complex behavior of many a flotation system In sulfide flotation, the precipitation of insoluble base metal xanthates is a well-known phenomenon although the conditions under which the precipitation reaction will proceed and the magnitude of the solubility products are not known with accuracy. A knowledge of the solubility of these xanthate salts will not only be of value in flotation research, but the mill operator might be interested in knowing whether precipitation of metal xanthate can be controlled or completely prevented in the flotation circuit thereby reducing reagent consumption, For these various reasons the solubility of lead, copper, zinc, and silver ethyl xanthate was determined. The experimental techniques and results will be discussed in this paper.

Jan 1, 1958