Search Documents

By Subhash Bhagwat

The definition of high sulfur coal varies from plant to plant and is subject to changes over time as the environmental regulations change. In plants constructed after September 1978 hardly any domestic coal can currently be burned without the use of Flue Gas Desulfurization (FGD) because a 70 percent reduction in potential S02 emission is mandatory even when the potential emission is less than 0.6 lbs. S02/106 Btu heat input. On the other hand older power plants may in many cases be legally emitting up to 6 lbs. S02/106 Btu or more under some State Implementation Plans (SIP). The Clean Air Act requires, however, that in the long run all stationary sources of S02 pollution must abide by the ceiling of 1.2 lbs S02/10 Btu heat input.. Coals with a potential to exceed this limit must, therefore, be considered as high sulfur coals. Such a definition would be unrealistic because many SIP's aim at an emission level of 1.8 to 2.0 lbs. SO2/106 Btu for existing plants and a stricter limit does not appear to be enforceable in the next 5 to 10 years. As a result, coals with an emission potential of greater than 2.0 lbs of S02 per 10 Btu heat input are considered high sulfur coals for the purpose of this investigation. Based on this definition and the 1984 actual consumption of coals by U.S. electric utilities (table 1) only 7 out of the 24 coal producing states could be categorized as low sulfur states. The actual S02 pollution, however, depends on total tonnage of a type of coal as well as the sulfur content of the coal. Table 1 also indicates that only 6 states--Kentucky, Illinois, West Virginia, Ohio, Pennsylvania and Indiana-account for nearly 77 percent of S02 pollution potential in the United States. These 6 states have therefore been chosen for this investigation.

Jan 1, 1986

By Jacques Mongrain, Serge Barbeau, Gary Brierley

The Communaute Urbaine de Montreal is currently involved in construction of the South Interceptor which consists of 53 kilometers (33 miles) of 1,800 mm (6.0 ft) to 5,400 mm (18.0 ft) diameter tunnels for the purpose of collecting, storing, and delivering sanitary and combined sewage to the treatment plant. Work is divided into ten separate contracts; nine of which have already been bid. The purpose of this paper is to describe construction activities that have been performed through the end of 1986 with emphasis on a general layout of facilities, a summary of subsurface conditions, and brief descriptions of actual construction activities for the six contracts where tunneling has been performed. All projects are being excavated with tunnel boring machines.

Jan 1, 1987

By Donald R. Williamson

The Cyprus Pima Mining Company's open pit operation was started in 1957 with the normal assumption that the ore reserve estimate was accurate within an acceptable range of values. At that tine reserves were law - volume (+10 million tons) and high grade (+1.5% Cu). Several periods of growth have brought the operation to its present production level of 55,000 tons per day of ore and +125,000 tons of waste. Over the years, a number of attempts to refine and polish the ore reserve figures have been made using a variety of established standard procedures. None of these attempts have produced results which are totally satisfactory, particularly when comparisons are made between ore reserve estimates and short to medium range production figures. Other refinements were tried using adaptations of established methods combined with computer modeling techniques. The resulting mine-model ore blocks were an improvement but they still tended to show too match tonnage of mill feed, often at too low a grade. One attempt at Kriging had only limited success. Statistical studies of operations data revealed relationships which could be used to subdivide ore blocks in much the same way as they are actually mined. Comparisons thus far between these newly developed ore blocks and production data show that the new method of evaluation yields excellent results. A new, better procedure for estimation of ore reserves apparently has been developed for the Cyprus Pima deposits. The specific procedures seem likely to have direct application to other, similar operations. The methods used to develop the procedures could be of value to still other operations.

Jan 1, 1976

By İsmail İnce

The existence of water is one of the most effective factors in deterioration of natural building stones. In the process of deterioration, capillary water absorption is the most significant procedure of water penetration into the building stones. Pyroclastic rocks have been widely utilized as building stone especially in historical buildings and monuments since ancient times in the Central Anatolia in Turkey. Nowadays, this type of rocks is used in the restoration of historical buildings as well as in the construction of modern buildings. Pyroclastic rocks are highly susceptible to deterioration process. Capillary rise has a significant influence on water penetration into building stones. Therefore, it is quite important to identify the factors affecting the values of capillarity, capillary rising speed, and capillary rise that define capillary water absorption in these rocks. To this end, pyroclastic rock samples in different textures were compiled from the Cappadocia region, in Central Anatolia. First, petrographic, mineralogical, geochemical, physical, and pore diameter distribution properties of the samples were determined in the laboratory. Then, capillarity values with capillary rise and capillary rise speeds dependent on time were established. Based on the data obtained, correlation coefficients between matrix percentage and capillary water absorption rate and capillary rise values of pyroclastic rocks were calculated and found to be as 0.850 and 0.891, respectively. Thus, the article proposes a new empirical equation to practically calculate the capillary rise value depending on the matrix percentage (MP) and median pore diameter (MPD) values.

Nov 30, 2020

By A. Noble

"In coal and mineral processing, several numeric parameters are used to quantify the separation performance of unit operations. For density-based separations, the partition curve is used as the starting point for many stages of diagnostic analyses. The curve is often quantified by its midpoint slope sharpness, and this single value is subsequently used for technical evaluation, benchmarking, and comparison. While this analytical approach does depict misplacement by relative density class, it inherently prioritizes middling separation and does not consider process economics or the micro-price value of individual classes. Alternatively, the organic efficiency parameter does consider process economics; however, it does not reveal information on the root cause of lost revenue or misplacement. In this paper, a new analytical approach is introduced which reconciles the technical misplacement data derived from the partition curve with the economic data derived from micro-pricing. The result is a new analytical procedure which reflects a better use of performance data. INTRODUCTION Partition curves are commonly used in the characterization, evaluation, and simulation of various physical separators. In mineral processing, partition curve analysis is routinely applied to hydrocyclones, screens, and density separators. Graphically, the partition curve depicts the recovery of particles as a function of a physical property on which the separation is based (e.g. particle density, size, magnetic susceptibility, etc.). Given the probabilistic nature of many real separators, the partition curve often exhibits a characteristic “S” shape (Fig. 1), similar to a cumulative normal distribution. Other geometric features of the curve are also depicted in Fig. 1, including the high and low closeout (or bypass) values, the midpoint slope, and the separation cut point (property value with 50% recovery). Partition curve analysis was originally proposed to evaluate coal washability (Tromp, 1937). Given the limited computational resources at the time, the analytical methods relied heavily on graphical construction and interpretation of the curve. Owing to the simplicity of the calculation and interpretation, many of these graphical approaches are still widely used for performance analysis today. The most common calculations are based on the slope of the partition curve at the midpoint. Increased slopes correspond to enhanced separation performance, since a perfect separation exhibits a stepwise transition from 0 to 1 at the desired cut point (i.e. an infinitely large slope). One common formulation of this slope, the Ecart Probable (Ep), is derived by evaluating the slope between the 25% and 75% recovery points:"

Jan 1, 2015

In this paper, a number of novel hypotheses that provide a fresh perspective on the characterization of strata movements associated with longwall mining are developed by analyzing subsidence measurements with an influence- function-based computer program. With this influence-function technique, easily obtained surface displacements can be used to determine some of the complicated, expensive, and difficult to measure movements of the immediate roof strata in a longwall panel. The primary hypothesis developed by this analysis proposes the existence of an area of partial roof caving near the edge of a panel called the "edge effect." A second hypothesis, interrelated with the first, promotes the importance of the effect of gate-entry closure on the observed strata movements. Both the primary edge effect hypothesis and the secondary hypothesis concerning gate-entry closure are justified and quantified in an extensive analysis of surface subsidence that uses supporting information from related theories, design criteria and insitu measurements. Next, the edge effect and the gate closure hypotheses are extended further and used to provide an explanation of the complex subsidence interaction of adjacent longwall panels in what is termed a "redisturbed" effect. Finally, in the conclusions of this paper, the importance of accurately understanding these longwall strata movements for proper subsidence prediction or gate design is stressed.

Jan 1, 1986

By James R. Arnold, John G. Mansanti

BACKGROUND Gold Fields Mining Corporation started their Chimney Creek operation in late 1987. The dump leaching operations commenced in October and the mill startup took place during the last half of November. The milling process at Chimney Creek is almost a conventional CIP plant with the major exception being the installation of a second thickener as a washing stage prior to CIP12 ' A simplified flow sheet is shown in FIGURE 1. Most of the gold in the mill is liberated by grinding in cyanide. After grinding in a conventional SAGball sill circuit, the cyclone overflow reports to the thickeners. The thickener overflow from the first thickener is pumped through 5 stages of carbon columns for gold adsorption. Slurry from the thickener underflow is leached, washed, re-thickened and pumped to CIP. After approximately 6 hours of retention time in CIP, the slurry is pumped to tailings for final deposition. The carbon from CIP is transferred to the third stage of carbon adsorption and then advanced as normal through the columns and strip circuit. Loaded carbon is stripped at approximately 1500C (3000 F) and 55 kPa (80 psi). After 4-5 hours of stripping, the grade of four tons of carbon is reduced from 5,140-6,860 g/t (150¬200 oz/ton) to typically 17 g/t (0.5 oz/ton). Zinc precipitation is used to recover the gold from the pregnant solution. After a water wash, the stripped carbon is transferred to acid wash or to the kiln feed tank for reactivation. All strip lots are acid washed in 3.0% HC1 and all stripped carbon passes through the kiln for thermal reactivation. Then the carbon is quenched, sized and stored in tanks or bins for transferral to CIP or to the carbon columns. Loaded carbon from the dump leach circuit is treated in a circuit consisting of five carbon columns which are parallel to the mill circuit. No distinction is made between the mill or dump leach carbon once the gold has been stripped from them. CARBON FINES HANDLING Once the carbon has been transferred from the carbon columns, every effort is made to minimize carbon attrition and to recover the carbon fines that have been generated in the process. Wemco Hidrostall pumps are used for transferring all carbon in

Jan 1, 1990

By Gilmore R. Tostengard

The advent of inexpensive computers has opened vast opportunities for improved planning and control of capital projects. The mining and mineral processing industries have welcomed the opportunity, and new and improved quantitative management techniques have abounded. This chapter will discuss commonly used computer applications for economic justification of the project, preparation of the cost estimate, planning the work schedule, monitoring work progress, and control of costs and productivity. Finally, there is a review of the degree to which the industry uses these applications. Our experience suggests that while we in the industry have been quick to adopt the new techniques, the quality of our input data has not always kept pace. During the next decade, our push should be toward improving the quality of the basic data and assumptions so that we can fully benefit from the sophisticated techniques. The GIGO (garbage in, garbage out) principle is a wellworn cliche, but it is especially valid here. One of the keys to getting good input is commitment. Unless the managers who are to use or benefit from the system are committed to it, the effort will fail. They must be com- mitted to the underlying principles of planning and control sufficiently to expend their time and resources on them; planning should be especially given emphasis. They can't be too busy to plan.

Jan 1, 1979

By Charles G. Frush

The function of the mine surveyor is to (a) provide a network of points of accurately known position, covering the entire mine property, (b) obtain the required data for the preparation of useful maps and sections! (c) provide position and directional control for the guidance of the operations, (d) measure the progress of the work, (e) measure the movement of rock masses, and (f) make miscellaneous surveys as needed. Mining properties range from the very small to the extremely large, and from those which involve only surface operations to those involving extensive underground workings. Active mines undergo constant change, necessitating continual updating of the surveys. The differences in the character of the deposits, the scale of mining and the mining methods result in large differences in the surveyor's activities and techniques, but many of the problems involved are common to most mines. The surface work of the mine surveyor is very similar to that, of the plane surveyor in that control points are established by triangulation, trilateration and traversing. Detail is taken by direct measurement, by stadia and by aerial photography. The equipment used, the techniques and the methods of processing the resulting data are likewise very similar. However, the underground work is quite different : A. The lines of sight frequently must be carried through constricted openings, often involving short lines of sight and awkward setups. B. The lighting often is poor, requiring illumination of the backsights and foresights, and the crosshairs. C. The ambient conditions often are difficult, involving falling water, high tem- peratures, poor visibi 'kv and heavy traffic through the area being suneyed. D. The surrounding rock map be unstable, resulting in movement or loss of the surveying stations, as well as hazard to the surveyors. E. The points to be measured often are difficult or impossible to reach. F. Steep vertical sights often are necessary, requiring the use of special equipment. G. Many working levels commonly are involved, requiring the transfer of position and orientation to each with a high level of precision. This section therefore will concentrate on surveying problems peculiar to the mine surveyor, chiefly underground work. 22.1-THE MINE COORDINATE SYSTEM A system of coordinates is essential for all permanent mining operations It is very desirable that all mining operations in a ,given area b~ tied into the same system, as this minimizes problems of boundaries and connections Whenever possible this system should be tied into and made part of the state or regional grid system. It is desirable to orient the coordinate grid on a true-north line and to position the origin of the coordinates so that all of the work will be in the "northeast" quadrant, making the north and east coordinates always positive. This can be done by subtracting suitable constant values from the north and east coordinates of the regional system The residual values are of more convenient magnitude and can be used as the local mine coordinates. If the long axis of the mineralization is not generally north-south or east-west.

Jan 1, 1973

By Bruce B. Hanshaw

The Tertiary carbonate aquifer of central Florida is composed of about 2/3 calcite and 1/3 dolomite with minor amounts of quartz and apatite. The Mg content of the calcite is lower in the recharge areas than in the deeper confined parts of the aquifer system. Various geochemical lines of evidence indicate that much of the dolomite is of penecontemporaneous origin but that some may have been formed much later, possibly by ground water. Theoretical studies indicate that the Mg/Ca ratio in solutions is about unity for the three-phase equilibrium, calcite-dolomite-water. Solutions, such as ocean water and some subsurface brines, have Mg/Ca ratios higher than one and should represent dolomitizing solutions. In the areas of principal recharge to the Floridan aquifer, ground water is undersaturated with respect to both calcite and dolomite, and the Mg/Ca ratiois as low as 0.05. As the water moves downgradient, the Mg/Ca ratio systematically increases and approaches unity; saturation of the solution with respect to both calcite and dolomite also increases with length of travel in the system. Thus, in the zone of active potable-water circulation, the chemical process is one of dissolution of minerals until saturation is reached or exceeded. However, in the deeper brackish-water zones that underlie peninsular Florida, dolomite may be forming where the Mg/Ca ratio is greater than one. The necessary Mg may be derived from ocean water or brines recycled through the system as the hydrologic regimen is changed. The driving force may be simple mixing, relative fluctuations of sea level, or a combination of mechanisms.

Jan 1, 1972

By J. R. Maxwell

The development, commercial installation, and operating performance of large capacity Maxwell Flotation Cells. Volumes ranging from 300 cubic feet to 2,000 cubic feet per flotation mechanism.

Jan 1, 1971

By Earl Gardiner, Michael Grenier, Stephen Hardcastle, John Vergunst

A prototype, self-contained mine refuge station air supply sys- tem was tested in an underground metal mine to verify it's ability to keep oxygen and catbon dioxide levels at acceptable concentrations in an emergency situation. In this test, 25 volunteers were assembled and sealed in a functional underground refuge station for a period of 24 hours, without the benefit of the standard com- pressed air supply. The prototype system was designed to: 1) operate on a self-contained power supply for a period of at least 27 hours; 2) supply oxygen at a metered rate; and 3) remove car- bon dioxide by re-circulating refuge station air through soda lime scrubbing beds. During the test period, the catbon dioxide concentration remained at an average of 2500ppm and oxygen concentration stayed between 20.2% and 20.6%. The volunteers found the prototype easy to use and seemed confident in its ability to provide a safe atmosphere. The test showed that this technology could become part of an underground mine's refuge station emergency equipment.

Jan 1, 1997

By N. T. Rempe

The underground voids that result from mining provide opportunities for deep geologic waste disposal (DGWD). Such disposal could solve many environmental problems. DGWD takes careful planning, technology transfer and true partnership between waste generators and mine/repository operators. The US government is now planning on using specially mined excavations to dispose of radiotoxic and mixed waste. Using the experience gained from the domestic projects that are now in preparation and from foreign repositories that are now in operation, US mines can claim their rightful share of the growing market for DGWD.

Jan 1, 1997

By Jack C. Haptonstall

The Tayoltita Unit of Minas de San Luis, S. A. is situated in an isolated corner of the state of Durango, Mexico. The ore deposits in the region were first worked by Indians, but by 1757 the Spaniards had discovered them, and the first systematic exploitation of the mines commenced. By the early 1900's most of the mines had been acquired by American interests, and the San Luis Mining Company was organized. The modern period of exploitation, uninterrupted for the last 74 years, began. In 1962 the company was fully "Mexicenized" in compliance with the modification of the mining law, and the name was changed to Minas de San Luis, S. A. Tayoltita continues as one of Mexico's most important silver and gold mines. The ore is extracted in en extensive underground operation, mining epithermal fissure veins by selective methods. The ore is milled and treated in an efficient counter-current cyanide plant, where 95 % of the silver and 96 % of the gold is recovered. Current annual bullion output is 55,000 kg (1.7 million troy oz) of silver and 1000 kg (31,000 troy oz) of gold from milling 165,000 try (181,900 stpy). Rough, 33-kg (1000-troy oz) bullion bars are smelted at the mine, shipped by air to Mazatlan, Sinaloa, and are thence sold to the Met- Mex Peñoles smelter in Torreon, Coahuila. Ore reserves, blocked by very conservative methods, are currently at 540,000 tons (595,000 st). Ore reserve grade is 425 g of silver and 6 g of gold per ton (12.4 troy oz Ag and 0.18 troy oz Au per st).

Jan 1, 1976

By K. T. Brashear

Since the MINER Act of 2006, the minimum static load of in-situ underground mine seals has been increased from 20-psi to either 50-psi if monitoring is conducted or 120-psi if left unmonitored. These minimum strength requirements in seals must be designed, built, and maintained throughout the lifetime of the seal. Due to this, it has become necessary to assess the effectiveness of non-destructive testing (NDT) technologies to determine seal integrity, which in this case, are explored using sonic waves and tracer gases. Through both small and large scale testing, two NDT methods will be evaluated for their abilities to determine integrity of the seal. A sonic wave technique to observe a change in wave velocity to identify faults within the seal material. As a NDT method, tracer gases may be used as a potential indicator of a connection between both sides of the seal material through a series of faults and cracks within the material itself. This paper reviews the history of underground mine seals and discusses the overall assessment of sonic waves and tracer gases to serve as NDT methods for estimating the integrity of these seals.

Feb 23, 2014

By Paul H. Johnson

The CH Leaching process is a new, more sophisticated, form of gold, silver, uranium and sulfide copper heap leaching wherein each layer of a multi-layered heap is divided into a number of independent cells, each of which are successively formed and leached in the top layer of the heap to their maximum economic recoveries, and then rinsed and sealed from further leaching. Triangular earth berms form the outside walls of the heap and a gridwork of rock-filled berms on top of the bottom pad form independent under- heap solution storage zones. The high degree of solution recirculation and staging that occurs in this process produces a relatively small volume of very rich pregnant solution. The cellular heap design and its mode of operation result in a uniform, intensive, long-term leach for all of the ore particles in the heap. Besides improved metal recoveries, the process appears to have several cost and operating advantages. In the CR2MR process, sulfuric acid and a soluble sulfide are added to a gold and/or silver pregnant leach liquor to precipitate most of the contained silver, mercury, copper, etc. as sulfides at a pH below 2.5. The other product of the reaction is solubilized HCN. Following a liquid-solid separation step, cyanide is regenerated in the supernatant solution by raising the pH to a level above 9.0. This process regenerates a portion of the cyanide used in the leaching step, removes contaminant ion species (silver, copper, mercury, etc.) from the leach solution and, in a subsequent step, recovers the gold in an enriched form. It is believed that substantial cost savings may be experienced by the use of this process in some gold and/or silver leach systems.

Jan 1, 1984

By Ted Budd, Vladimir Goubanov

The East Central Interceptor Sewer, commonly known as the ECIS Project, is the largest public works construction project awarded by the City of Los Angeles. The complexity of this $240 million project, together with the challenge created by the mandated 1,000 calendar days for construction completion, make this project a major interest for the tunneling industry. This paper will describe the ECIS tunnel project, currently under construction by the Joint Venture of Kenny (Sponsor) / Shea / Traylor / Frontier-Kemper. Mining of the18.5 km (about 11 miles) long and 4.7 m (15ft-4in) diameter tunnel is underway with four Tunnel Boring Machines mining at the same time. Details on the mining machines, muck handling systems, innovative construction sequence, together with mining progress will be given.

Jan 1, 2003

By Lawrence K. Nordell, Vinit Sethi

Published standards and specifications do not adequately cover engineered class pulleys for modern high strength steel cord belt conveyors. This paper discusses the Conveyor Dynamics, Inc. (CDI) design criteria and stress analysis techniques emphasizing the finite element method (FEM), fatigue failure criteria, design limits and manufacturing requirements to ensure successful and safe pulley installations.

Jan 1, 1993

By F. F. Aplan, T. H. Wentzler

Limestone is potentially a low cost material for the neutralization of acid mine drainage and other acidic waters such as steel pickling liquor. Unfortunately, when limestone is reacted wit9 these waters containing large amounts of Fe , Fe+3, and SO4-2 , a coating of gypsum and iron hydroxides form on the surface of the limestone inhibiting further neutralization reactions. The nature of these coatings, their morphology, composition and thickness were evaluated using the scanning electron microscope and microprobe, and the kinetics of limestone dissolution was studied both in the presence and in the absence of the reaction-inhibiting coatings. These data were then correlated with the solution chemistry.

Jan 1, 1992

By Robert B. Scott

Acid mine drainage, discharging from coal beds, has polluted our streams and rivers since early time. These pollutants affect water quality by lowering the pH, reducing natural alkalinity, increasing total hardness, and adding undesirable amounts of iron, manganese, aluminum and sulfates, The tangible damages are the costs involved in replacing equipment corroded by the acid water, additional treatment costs at municipal and industrial water treatment plants, and damages resulting from corrosion of steel culverts, bridge piers, locks, boat hulls, steel barges, pumps, and condensers. Intangible damages, which are real and important, include destruction of biological life of the stream, reduced property values, and streams rendered undesirable for recreational uses.1 The major problems of mine drainage occur in the anthracite and bituminous coal regions in Appalachia. However, many of the western mining states have significant mine drainage problems in specific areas, but the overall problem is not as great as in the eastern states.

Jan 1, 1970