Search Documents

By Verya Nasri

The proposed Second Avenue Subway Project in New York City is approximately 8.5 miles long, up to a depth of 120 feet beneath grade and runs the length of the eastern side of the island of Manhattan from Harlem in the north to the financial district in the south. It will reduce overcrowding and delays on the existing parallel line, improving travel for both city and suburban commuters, and upgrading access to mass transit for residents of the East Side of Manhattan. This subway line will have 16 new stations providing transfers to the existing Metro-North commuter rail service and to New York City Transit subway lines and bus services. The first phase of construction includes two TBM rock tunnels 2.4 miles long and two new large and shallow rock cavern stations with clear span openings ranging from 70 to 100 feet and length in excess of 1000 feet with 615 feet center platform, coupled with low rock cover ranging from 20 feet to 40 feet. The design methodology for these large and shallow rock caverns consists of using well known empirical methods for initial estimate of support requirements and then two and three dimensional continuum and discontinuum analyses for verification of the selected excavation sequence and support system. This paper describes the analysis and design methodologies used for the two large and shallow rock caverns with insight into how to overcome the design complexities and construction challenges of the urban underground.

Jan 1, 2008

By M. Ahrens

The paper describes the main drive systems of an iron ore pelletizing plant and related important design aspects. It is shown how today?s drive systems provide the desired flexibility for the process and lead to high energy efficiency and system reliability. With respect to electric drives expansion projects have many technical issues in common with green-field installations. However, there are aspects where important, distinct differences occur. It is shown which considerations for selecting and sizing drive systems for such a plant as well as for integrating them into an overall plant control concept need to be taken into account. Besides the design of the drive systems a key aspect for such an expansion project is the network interaction. Harmonics levels at different points in the plant network need to be checked carefully with simulations during the design phase to avoid problems later-on during operation. The power factor compensation and the harmonic filtering of the new production line cannot be designed independently of the already existing plant. The paper highlights areas where problems could occur and which points need to be paid attention to when a plant is expanded.

Jan 1, 2008

By Dapeng Zhang, Brij Moudgil, Shibo Zheng, Chunhui Feng, Wenyi Song, Wending Xiao, Patrick Zhang

Separation of dolomite from phosphate is the most challenging problem in phosphate mineral processing. Over 50% of the future phosphate reserve in Florida contains too much dolomite to process using the current industry practice. The current phosphoric acid production practice requires less than 1% MgO in the phosphate concentrate as the feed material. The Florida Industrial and Phosphate (FIPR) Institute has collaborated with worldwide experts in the field to address this issue. As a result, the industry is now offered three feasible options. Option 1 offers three methods for reducing MgO content in the concentrate from the Crago process, including adding a dolomite depressant in the rougher flotation step, dolomite flotation of the cleaner concentrate, and scrubbing the cleaner concentrate in quartz sand. These methods could reduce MgO content in the final concentrate by 20–40%. Option 2 involves crushing and grinding of high-dolomite phosphate pebbles followed by dolomite flotation at slightly acidic pH using a new collector that does not require phosphoric acid as a phosphate depressant, achieving a final concentrate analyzing less than 0.9% MgO at about 87% P2O5 recovery. Option 3 is a gravity separation technique using an innovative separation jig, and its full potential remains to be demonstrated.

By John S. Hutchins, David L. Wassum

Mining engineers are ready to take a big step into a new field-oil mining. To understand the subject, one must look at the world's oil supply and demand as well as petroleum technology successes and failures. The US has an abundance of solid hydrocarbon and uranium energy resources, but 75% of its energy for industry, transportation, manufacturing, and space heating comes from liquid petroleum and natural gas. So there are increasing efforts to discover new oil reserves; today the number of drilling rigs operating in the US is at an all-time high. But with 80% of the world's wells already located in the US and Canada, good new exploration prospects are difficult to find. The cost of drilling deep new wells has also greatly increased. The US faced a similar situation in the early 1950s, when primary oil production declines began. During that time, the petroleum researcher introduced secondary recovery techniques such as water flooding and gas injection. This increased the average amount of extractable oil from discovered US reservoirs from 17% to 33%. Production soared and the world petroleum price remained stable until the end of the 1960s. Secondary recovery techniques were then supplemented by tertiary oil recovery technologies-increasing sweep efficiency with such things as CO2 injection-that are, so far, only partially successful in most petroleum fields. Even so, these technologies could raise cumulative recovery expectations to 35-38%. The "lost" oil in depleted US reservoirs equals 48 km3 (300 billion bbl) of conventional oil, or 12 times the current recoverable reserve base. At the present rate of US consumption-1 km3/a or 6 billion bbl/a-this is enough to run the US for 50 years without importing any oil. Moreover, there are 16-24 km3 (100-150 billion bbl) of as-yet unrecoverable heavy oil and tar sands in the US.

Jan 12, 1981

By R. N. Tempel, M. Lengke

Arsenic sulfide [orpiment, realgar, amorphous AsS and As2S3] oxidation rates were measured in mixed flow reactors at pH~2 and temperature of 25-30oC. The measured oxidation rates for arsenic sulfide solids by dissolved oxygen are in the range of 10-11 to 10-10 mole m-2 s-1 after being normalized to final surface area. The order of arsenic sulfide oxidation rates decreases at pH~2 from amorphous AsS > realgar > orpiment > amorphous As2S3. In comparison to pyrite, arsenic sulfide oxidation rates are approximately 1.5 to 15 times slower than pyrite oxidation rates at pH~2.

Jan 1, 2002

By Yoshinori Iwasaki, Shosei Serata, Yutaka Mochida

A new comprehensive insitu instrumentation technique named this RCC Method has been developed for rapid assessment and improvement of the structural stability of underground openings. When applied to tunnel construction, the degree of present and prospective safety of underground openings can be determined in quantitative terms within 10 to 20 minutes of microcreep observation. When applied to mining, roofs and floors can be stabilized by controlling the stress conditions. This stress control method has eliminated the need for intensive roof bolting and extensive floor renewal in all cases where it was applied. Use of this technique is illustrated by field examples from the Seikan Undersea Tunnel of Japan and deep potash mining in Canada. NEW INSTRUMENTATION TECHNIQUE: THE RCC METHOD Failure problems in underground excavation usually arise in weak non-elastic grounds where conventional rock mechanics theories of elasticity are not only useless but also misleading. Presently, discontinuity planes in the ground are being considered a factor in assessing these failure problems, and while this development is interesting academically, it is not of much use in actual excavation work, where it is nearly impossible to identify and quantize all existing planes of discontinuity. Even if such an extraordinary task could be accomplished at an underground excavation site, effective use of the data would be difficult and impractical for rapid excavation work, with the possible exception of rare cases of ideally elastic ground.

Jan 1, 1976

By Botelho Junior, Amilton Barbosa, Denise C. R. Espinosa, David B. Dreisinger

Copper and cobalt can be found on nickel laterite ores, and cobalt can be found also on copper ores, and many contaminants such as iron, aluminum, and magnesium are associated with these ores. In hydrometallurgical process, a purification step is necessary after leaching due to the presence of these impurities. Chelating resins are more selective for some metals than others, making them more efficient than cationic resins. This overview discusses chelating resin applications to recover copper, nickel, and cobalt from mining process and mining tailings and the effect of contaminants in leach solution. Chelating resins with iminodiacetate functional group can be used for selective copper recovery, and both iminodiacetate and bis-picolylamine resins are highly selective for nickel and cobalt. Chelating resins with the same functional group can have different performances on the kinetics of loading, because of variations of structure, the density of functional group, and degree of cross-linking. This article reviews commercial chelating resins that can be applied in leach solutions with different compositions, and also possible innovations for uses of chelating resins to recover metals from mining process and mining tailings.

By Dale S. Hursh, William A. Brooks

Introduction US dependence on external energy sources is dangerous because of unstable political situations existing in key energy exporting countries. So, recent national energy policies call for increased reliance on domestic energy sources. Coal ranks as the most feasible domestic energy source due to its abundant reserves and continental distribution. But to efficiently extract these coal reserves, huge sums of capital funds are needed. Due to the depressed economy, lenders of capital funds are forced to be more stringent with loan applications. This results in fewer loans granted. In many cases, it is uncertain if funding can be obtained. Furthermore, the greatest level of domestic mine financing is expected to be in the coal sector. Demand for capital in the domestic coal industry is anticipated to increase 80% by 1990. The Chase Manhattan Bank in New York warns that these future needs cannot be met by the present capital markets. This article analyzes the current and expected situations of the capital markets available to the domestic coal industry, including: • current and expected future types of financing used in the domestic coal industry; • problems the domestic coal industry may encounter as it seeks capital; and • the future availability of capital funds as concluded from analysis of the first two items. Background Information Regardless of industry, all projects or ventures can be divided into four basic stages: generation; evaluation; selection; and execution. Within the mining industry, one can break down these stages to draw a clear picture of mine development, as shown in Fig. 1. Each successive stage has a corresponding risk level. This risk level defines the type of financing available to the mine operator. Mining Venture Risks A coal mining venture can be characterized by its unique blend of technical and financial risk. As the mine moves through different development stages, varying proportions of each of these risks are encountered. It is these risks that the lender evaluates to determine project suitability. For a coal mining venture, the major complexities generally occur with the technical risk. These include: • quantifying the coal reserves: • assessing the feasibility of the mining method; and • evaluating the design of the wash plant. The reserve risk is gauged by the amount of measured, mineable, and saleable reserves. The greater the latter amounts, the lower the risk. Secure title to the reserves plus title for any surface areas required are also of concern to the banker. Feasibility of the mining method and evaluation of the wash plant design should verify that the project can be completed according to the engineered spec-

Jan 9, 1982

In Alaska?s southwest corner, in the Bristol Bay region, 476 holes have been drilled to help define the size of the Pebble Project. The results indicate that the deposit holds close to 32 Mt (72 billion lbs) of copper and 2.9 Gt (94 million oz) of gold. The Pebble Partnership, an Alaskan limited partnership of Anglo American and Northern Dynasty Minerals, owns the project that consists of two world-class mineral deposits. Currently in the prefeasibility and prepermitting stage of development, the Pebble Project is one of the largest and highest profile exploration projects in North America. History The Pebble West Project was originally discovered in 1988 by Cominco (now Teck Cominco). Drilling programs in 1997 defined a near-surface mineral deposit of 1 Gt (1.01 billion st). Minerals found included copper, gold and molybdenum. Northern Dynasty Minerals acquired the property in 2001 and, by 2005, it had confirmed a measured and indicated resource of 4.1 Gt (4.5 billion st) containing 1.2 kt (42.1 million oz) of gold, 11.2 Mt (24.7 billion lbs) of copper and 612 kt (1.35 billion lbs) of molybdenum and additional silver. By September 2005, Pebble East, a deeper, but richer deposit had been found. Drill data by the end of 2005 confirmed a 3.4-Gt (3.7-billion st) inferred resource containing 19 Mt (42.6 billion lbs) of copper, 1.2 Mt (39.6 million oz) of gold and 1.2 Mt (2.7 billion lbs) of molybdenum.

Jan 1, 2009

By Vince Luongo

PROJECT DESCRIPTION The York Durham Sanitary System (YDSS) Interceptor in the Town of Richmond Hill located just north of Toronto, Ontario, Canada will see the construction of a tunnel extending along 19th Avenue for a length of approximately 3.8 Km from Yonge Street, east to Leslie Street and will have a minimum internal diameter of 2.1 m. t to Leslie Street and will have a minimum internal diameter of 2.1 m. The tunnel will connect into four shafts, for which two of the shafts will be constructed using the slurry wall construction method given the high water table and difficult ground conditions encountered at these locations. The two shafts noted as Access Shaft No. 2 and No. 3 were designed and constructed to meet regulatory conditions, which required a sealed shaft construction method. GEOGRAPHICAL PROFILE The ground conditions in the Toronto region consist predominately of glacial till, glaciolacustrine and glaciofluvial sand, silt and clay deposits, and beach sands and gravels. The shallow geological formation found in the project area consists of four types of deposits: Oak Ridge Morain deposits, Halton Till, Glacial lake deposits and Organic soils. The Oak Ridge Morain is the dominant deposit encountered along the tunnel alignment. This formation consists of three deposits: The Upper Till, Middle Sand and the Lower Till. Standard penetration tests (SPT) carried out in these deposits measured N-values ranging from 2 to more than 100 blows/300mm which indicate very loose to very dense soil conditions. The Middle Sand deposit will be the dominant feature within the slurry wall construction at access shafts 2 and 3. Access Shaft 3 The base of the slurry wall will be 20.5 M below the ground surface. Slurry wall excavation will be within peat and organic soils found at the upper 3 M, followed by 5 M of the Upper Till. The remainder of the excavation will be within the Middle Sand. The piezometric head elevation is found at the ground surface. Access Shaft 2 The base of the slurry wall will be 22.5 M below the ground surface. Slurry wall excavation will be entirely within the Middle Sand 2.The piezometric head elevation is found at 7 M below the ground surface.

Jan 1, 2007

By Adrian Coombs, Paul Magowan, Derek Zoldy

Continued development and intensification are fuelling the urgent need for new trunk infrastructure within The Regional Municipality of York and throughout the Greater Toronto Area. Permitting of these projects is increasingly subject to public scrutiny to severely restrict dewatering through construction technologies and the requirement for a comprehensive and effective Environmental Management Plan. Three current projects: one on the York Durham Sewage System and two in the City of Toronto 1.Conventional Design, Tender, Award: 4,150m (13,600 ft.) 2.7m (9 ft.) finished interior diameter soft ground tunnel for York Region’s YDSS Interceptor Trunk Sewer 2.Negotiated Contract: 3,800m (12,500 ft.) 3.5m diameter (11.5 ft.) rock tunnels for Enwave’s environmentally sustainable and innovative chilled water system in downtown Toronto 3.Conventional Design, Tender, Award: 2,200m (7,200 ft.) 3.3m diameter (10.8 ft.) rock tunnel for reinforcement of Hydro One’s primary hydro feed in the downtown core of Toronto These projects exemplify issues such as: EPB tunnel and sealed shaft technologies Substantial permitting requirements associated with dewatering Mitigation of rock creep Congested downtown rights-of-way Deep shafts and confined working compounds Unique scheduling and cost benefits when Owner, Contractor and Consultant can work together cooperatively.

Jan 1, 2007

By Gunter Swoboda, Harald Wagner

Until a few years ago tunnel construction was based exclusively on experience. In recent years, however, numerical models have increasingly become an integrated part of tunnel design [2]. These models permit good evaluation of the tunnel's support behavior even before it is designed. In particular, numerical methods are highly suited for the development of new construction methods. The prerequisite for this is the application of high-performance pre- and postprocessors, permitting the design engineer to come to a quick interpretation of the analysis results. In future, 3D analysis will take on increasing significance, for which reason this paper also deals with this type of models.

Jan 1, 1993

By R. E. Mitchell

Environmental Impact Assessment (EIA) is the accepted method for evaluating proposed mining and other industrial projects to obtain regulatory approval and to help companies plan for responsible development. Another evaluation system becoming increasingly more common for proposed projects is the Environmental, Social and Health Impact Assessment (ESHIA). An ESHIA differs from an EIA for its more comprehensive and inclusive approach to evaluate potential impacts on public health, and its ecosystem services approach to assessing biodiversity impacts. An ESHIA may also be required by certain lenders for financing major projects. Conducting an ESHIA for a proposed mining development is not without its challenges, with costs, scheduling, regulatory concordance and other constraints to be considered. This paper examines some benefits and challenges of ESHIAs and summarizes lessons learned using a case study approach.

Jan 1, 2012

By Erich J. Jacob

In the past 15 years the enforced improvement of the public traffic systems caused a boom in urban tunnel construction. In 1961 the City of Paris started to build the Express-Metro. Of the 47 km long double-track line crossing the city center, nearly 45 km are in operation since 1971. Still missing is here only an about 2.6 km long connecting stretch, which is under construction now. From 1963 to 1969 the 21.8 km long Victoria Line was built in London as extension of the existing network,. A little later, in the years 1965 to 1973, the City of Hamburg supplemented its subway network by the construction of a 16.8 km long line between the Boroughs of Billstedt and Stellingen. Also in 1965 the City o Munich started to build a subway system of 54 km f length. Thereof a stretch of 16.2 km could be taken into operation in 1972 shortly before the Olympic Games. These are only some of the better known projectsas examples of the activities in European cities. In nearly all cities with more than about ½ million inhabitants subsurface traffic lines were begun or supplemented. Furthermore, numerous undercuts or other subsurface structures were built. The Ij Tunnel in Amsterdam and the new Elbe Tunnel in Hamburg may be mentioned, both structures finding international attention.

Jan 1, 1976

By Thomas Kuhn, Carsten Ruehlemann, Christina Heller, Anna Wegorzewski

The commercial extraction of metals from manganese nodules on an industrial scale requires more than 50% of the investment necessary to realize manganese nodule mining. This is mainly due to the fact that a completely new metallurgical processing scheme for the extraction of both base metals (Ni, Cu, Co) and high-tech metals (Mo, Li, Ga) has to be developed and upgraded to industrial scale. There are a number of conventional processing technologies that combine hydro- and pyro-metallurgical approaches such as the INCO and CUPRION processes which have been developed in the 1970s and 1980s. Today, new approaches based on selective leaching with chelating agents and bioleaching try to minimize energy consumption and waste production. All of these extraction methods require knowledge how the metals are structurally bound in the manganese oxides. In this contribution we will review the current knowledge about the mineralogy of iron and manganese minerals in the different marine oxide deposits, present our results, and discuss the possible consequences for metal extraction.

Sep 1, 2014

By F. X. Spachtholz

"Raw materials industry is crucial for national economy. German mining companies are known for their high degree of resource efficiency based on modern technology and know how. K+S is one of the world’s leading suppliers of standard and specialty fertilizers. In the salt business, K+S, with sites in Europe as well as North and South America, is the world’s leading producer. The mine sites of K+S are distributed all over the world producing mainly potash and magnesium salts and rock salt. Focus is on the sustainable use of the natural deposits in order to stay competitive. For this reason a raw material policy, both national and international, is necessary to ensure access to new mineable deposits which are still available in Germany. Further on, knowing market conditions is a must for sustainable development. At least sustainability and resource efficiency in potash and rock salt mining are achieved by constantly developing new technologies as well as optimizing the organization and improving qualification of workers."

Jan 1, 2011

By Stavros H. Constantopoulos

Mediterranean regions such as Greece, Turkey, Cyprus, Corsica and New Caledonia have experienced epidemics of malignant mesothelioma as a result of non-occupational, ??domestic?? exposure to tremolite asbestos and fibrous erionite. This exposure to tremolite asbestos and fibrous erionite is typified ??domestic?? due to its prevalence in regions with natural deposits of tremolite asbestos (or fibrous erionite) where the material from tremolite asbestos or fibrous erionite is used for domestic applications such as whitewashing. However, these exposures may be useful in examining the potential consequences of even small amounts of amphibole asbestos fibers in the ambient air. It can also elucidate the effects of fibers that behave like amphibole asbestos. However, this type of exposure is not useful for studying the potential effects of small amounts of asbestos in the ambient air of big cities due to the differing nature of the fiber types and modes of exposure between the regions. © 2008 Published by Elsevier Inc. Keywords: Tremolite asbestos; Erionite; Domestic; Environmental; Exposure

Jan 1, 2007

By M. A. Meyer

Underground mining accidents in the USA in recent times have prompted the Mine Safety and Health Administration (MSHA) to review emergency and tracking systems for underground mines. Several communication and tracking systems are available on the market and various systems have been installed in mines around the world. In addition, MSHA?s standard on Diesel Particulate Matter (DPM) requires mines to comply with the final PEL of 160µg/m3 by May 20, 2008. Barrick Goldstrike Mines Inc., Underground Division, has been in operation since 1995 and an extensive control and monitoring network, and a leaky feeder voice network is in place. Enhancements to the communication and control system are currently being implemented to include a PED emergency notification system, wireless LAN with tracking of personnel and equipment in the mine, and a ventilation control system that will use the tracking information and ventilation data to automate much of the mine ventilation system. Expected benefits from such a system would be enhanced communication with miners, emergency notification, location of miners and equipment, energy savings, improved ventilation control, and improved atmospheric conditions in the mine including reduction of diesel particulate matter (DPM).

Jan 1, 2009

By R. G. Benson, P. R. Wotruba, K. W. Schmidt

Introduction The Fortitude deposit is located in Nevada's Battle Mountain mining district in the central Great Basin region of the Basin and Range province of the western US. The deposit is at Copper Canyon in the southernmost portion of the district, about 19 km (12 miles) southwest of Battle Mountain (Fig. 1). Mining activity in the district began in 1866 (Roberts and Arnold, 1965). Base and precious metals were mined by underground methods intermittently until 1955. Placer gold was first discovered at Copper Canyon in 1912. Moderate scale dredging of alluvial gravel at the mouth of Copper Canyon was conducted by the Natomas Co. from 1944 to 1955 (Johnson, 1973). In 1967, Duval Corp. began large scale open-pit copper mining. (Sayers, Tippett, and Fields, 1968). Copper prices decreased and precious metals prices increased in the mid-1970s so Duval's exploration efforts at Copper Canyon shifted to precious metals. These exploration efforts resulted in the discovery of the Tomboy-Minnie deposits and shortly afterward, the Northeast Extension deposit at Copper Canyon (Blake, Wotruba, and Theodore, 1984; Fig. 2). The Fortitude deposit was discovered in late 1980, after Duval had proceeded with precious metals production at Copper Canyon. Converting the existing plant facilities at Copper Canyon to a precious metals recovery system was completed in 1978 (Jackson, 1982). Production from the Tomboy-Minnie deposits began in early 1979. Precious metals production moved to the Northeast Extension deposit in 1982. In late 1984, after three years of preproduction stripping and mining of the Upper Fortitude ore zone, production from the higher grade Lower Fortitude ore zone began. Currently, Battle Mountain Gold Co. operates the Fortitude deposit. Production from the Battle Mountain mining district before 1967 included 4.6 t (150,000 oz) of gold, 65.3 t (2.1 million oz) of silver, 13.6 kt (15,000 st) of copper, 4.5 kt (5,000 st) of lead, and 13.6 kt (15,000 st) of zinc (Roberts and Arnold, 1965). At the time of Duval's 1967 start-up, ore reserves at Copper Canyon included 12.6 Mt (14 million st) in the East ore body and another 3.6 Mt (4 million st) in the West ore body. Both had average grades of 0.79% copper, 16.1 g/t (0.47 oz per st) silver and 0.86 g/t (0.025 oz per st) gold (Blake et al., 1984). The Tomboy-Minnie deposits collectively contained 3.5 Mt (3.9 million st) of ore grading 3.09 g/t (0.09 oz per st) gold and 9.6 g/t (0.28 oz per st) silver. The Northeast Extension reserves were identified as 1.4 Mt (1.5 million st) of ore with an average grade of 2.9 g/t (0.085 oz per st) gold and 5.1 g/t (0.15 oz per st) silver. Initial total reserve estimates for the Fortitude deposit were 14.5 Mt (16 million st) grading 5.14 g/t (0.15 oz per st) gold and 29.8 g/t (0.87 oz per st) silver (Jackson, 1982). Therefore, before large scale mining, the Copper Canyon area contained a minimum of 102.6 t (3.3 million oz) of gold and 541 t (17.4 million oz) of silver as mineable reserves. The Fortitude deposit reserves as of Jan. 1, 1985 were 10.6 Mt (11 million st) grading at 5.28 g/t (0.154 oz per st) gold and 28.5 g/t (0.83 oz per st) silver. Currently, the company is producing 6.8 t (220,000 oz) of gold and significant amounts of

Jan 7, 1986

By Andrea Koschinsky, Akira Usui, Michael Bau, Katja Schmidt, James Hein, Thomas Kuhn

Marine ferro-manganese (Fe-Mn) crusts and nodules are metal-rich chemical sediments that are archives of paleoceanographic proxies and potential metal resources and targets of deep-sea mining. Traditionally, crusts and nodules are subdivided into hydrogenetic, diagenetic, and hydrothermal types. While hydrogenetic Fe-Mn crusts are a potential resource for Co, Te, Pt, and REY, nodules are enriched in Cu, Ni, Mo, and Li, and hydrothermal deposits may be enriched in individual metals such as Mo, Ba, and Li, depending on the temperature and composition of the hydrothermal fluid. The different types of marine oxidic Fe-Mn precipitates, therefore, have different economic potential. Hence, a robust classification is not only helpful in the general geochemical characterization of such precipitates (and as such is a useful teaching tool, for example), but may also simplify the evaluation of their importance as a potential metal resource, which helps to prioritize exploration targets for deep-sea mining.

Sep 1, 2014