Search Documents

By R. D. Hancock

The loading and selective properties of a number of commercial and experimental resins developed for the extraction of base metals were evaluated. Particular applications that ",:ere considered included the extraction of copper from artificial dump liquors, the treatment of Iow-grade copper, nickel, and cobalt liquors, and the removal of nickel from a cobalt electrolyte. Reagents that showed promise were two experimental resins developed at Mintek containing pyridyl imidazole active groups and two Dow resins, XF4195 and XF4196.

Jan 1, 1982

By L. C. Woollacott

Some of the factors that may influence the reliability of a consistent material balance derived from plant data were investigated, data taken from a sampling of the Iow-grade tin-flotation circuit at Rooiberg A Mine being used as the basis for the investigation. The importance of subjecting a calculated balance to a thorough analysis of its sensitivity to erors in assay and flow rate measurements is highlighted. Several simple guidelines are derived from the analysis of the Rooiberg data, and these appear to be generaly applicable to process-evaluation exercises and to the technique used for the smoothing of material balances.

Jan 1, 1987

"Coal seam gas problems can adversely affect the safety and productivity of underground coal mines, leading to fatalities and financial losses. Conventional gas management technologies using ventilation and gas drainage are unable to deal with the high and irregular gas emissions associated with high-production longwall mining. New technologies need to be developed to supplement the traditional gas management techniques to minimize the hazard of coal seam gas. Thin spray-on liners (TSLs) have gained some success for rock surface support since their introduction to the mining industry. Due to their relatively low permeability and appropriate mechanical properties, TSLs also show potential to be used as a gas management tool in underground coal mines.In this paper we review the current gas management challenges and discuss the potential use of TSLs as a gas management tool in underground coal mines. This may involve reducing gas migration into the excavations/roadways, enhancing in-seam gas drainage, and preventing spontaneous combustion. Some potential areas for future research work are identified. IntroductionWhen a coal seam is influenced by mining activities, gas stored inside is liberated into the underground ventilation system. Gas emissions have created serious difficulties for the coal mining industry around the world. Therefore, coal mines have to develop effective strategies to control the gas concentration below the threshold value to meet statutory requirements. Ventilation has been the first solution in gas management for underground coal mining. When the emitted gas cannot be effectively diluted by ventilated air, gas drainage using pre- and/or post-drainage has to be introduced. However, even with ventilation and gas drainage, irregular gas emissions usually increase the gas concentration in roadways and slow down the development rate, thus causing significant economic loss to the coal mining industry (Thakur, 2006). Therefore, new technologies need to be developed to address this issue and mitigate the explosion risk."

Jan 1, 2016

By F. L. D. Cloete

The Relix process is based on direct contact between an ion-exchange resin and undiluted pulp, thus avoiding prior solid-liquid separation. The resin particles float near the surface of the pulp, forming an inverted fluidized bed with the pulp flowing downwards. The basic idea was demonstrated on a full-scale pachuca tank at Stilfontein Gold Mine in 1970, followed by a small-scale demonstration run in a laboratory at the National Institute for Metallurgy. A pilot plant based on a throughput of 60 tons of ore per day was subsequently operated at West Driefontein Gold Mine for several periods over two years. Although the plant proved operable from a mechanical point of view, the metallurgical performance was not up to expectation. The basic cause of the poor metallurgical performace was shown to be backmixing of both the resin and the pulp between stages. The values obtained for resin losses were inconclusive. Further development of resin-in-pulp processes for the recovery of uranium should be focused on the performance of various techniques for the screening of resin from pulp.

Jan 1, 1981

By M. Splaine, W. Davidson, D. C. Atkinson

Since 1964, Nchanga Consolidated Copper Mines, Ltd., has been developing and using production scheduling methods for optimizing its metallurgical operations in the short term (up to one year). Medium-range metallurgical planning has been possible only by successive evaluations of a single-year LP. A modified version of Rosenbrock's direct search technique has now been developed to allow multi-year optimization of both mining and metallurgy for medium-range planning. The modifications to the search technique have produced a marked increase in computational efficiency for this heavily constrained problem in many variables and the system is a usable planning tool, given a reasonably powerful computer. The plans are 'optimum' in the sense that they yield the maximum present value of the operations. Each of the resulting five-yearly mine plans forms the basis for further detailed metallurgical evaluation by the established production scheduling system.

By K. I. Afewu, L. C. Woollacott

The design of in-pulp adsorption vessels in the gold industry has, for the most part, been seen as a problem involving the suspension of fine particles o ore in a slurry. The need for the vessel to be designed as a mass-transfer contactor has received insufficient attention. The current series of papers addresses this need The previous paper considered the question of the scale dependence of the film transfer coefficient. This paper examines the mixing considerations that are relevant. A review of the literature and an examination of a limited set of data provide some insight into the mixing conditions needed for the dispersion of the particles of adsorbent. The mixing requirements for the suspension of the ore particles are also considered, and conclusions are drawn in regard to the design of mechanically agitated vessels for gold in-pulp adsorption circuits.

Jan 1, 1995

By E. Barnea

This paper simplifies and provides a strict mathematical proof for an equation developed by R. J. Woody for the c alculation of solute recoveries in countercurrent decantation. The equation offers a convenient method for the optimization of flowsheets involving a simple countercurrent-decantation circuit.

Jan 1, 1978

By J. J. Van Rensburg

The commissioning of a test facility for the calibration of anemometers by J. J. VAN RENSBURG (Student Member). After the erection of a commercially produced open-jet wind tunnel for the calibration of the anemometers used in mine ventilation, the wind tunnel was calibrated for routine use. There is a choice of five orifice plates. which, together with a variable-speed fan, can give a measurable range of air velocities in the test section from about 0,05 to 35 m/so The orifice plates were calibrated against a standard pitot tube, and it is now necessary only to measure the pressure drop across an orifice plate and to read off, from a set of graphs, the true outlet velocity in the test section. The paper describes the underlying theory and the test results.

Jan 4, 1975

By E. Adlard

This paper sketches an expert system for use underground in pinpointing problem areas in the operation of machines. The system is typically a software 'shell' designed to accommodate a series of 'if-then' rules that are intertinked to systematically search for the cause of the problem. During the search, the system asks a series of questions that have to be answered by the operator and then, when necessary, by an artisan. The rules of the system are generated by a knowledge engineer whose function it is to gather the necessary diagnostic information and prepare it in the required format for the expert system. Much still requires to be done in the development of such systems and in the testing of hardware to withstand the mining environment.

Jan 1, 1990

By P. J. D. Lloyd

An account is given of the development of a process to concentrate gold and other valuable minerals and to produce a discardable waste. In this process, the ore is coarsely milled, a bulk flotation concentrate is prepared, and the flotation tailing is scavenged in a hydrocyclone, which returns coarse gangue, moderately coarse valuable minerals, and locked valuable minerals back to the mill. The engineering developments required by this circuit in order that it will fit underground, and the progress made towards the achievement of those requirements, are reviewed. If the waste is to be suitable for use as a backfill in a deep-level, flat tabular excavation, it should be capable of being placed hydraulically, and should have both low voidage and high rates of drainage. Such a material could be prepared by the fine screening of the overflow from the cyclone in the proposed circuit. Possible methods for the handling of the concentrate and the recovery of its valuable constituents are described. The paper concludes with a discussion of the possible benefits from the use, in deep-level Witwatersrand mines, of a system involving concentration underground, extensive backfilling using the tailings from the concentration process, and hydraulic hoisting of the concentrate.

Jan 1, 1979

By J. N. van de Merwe

CONTRIBUTION BYH. WAGNER AND T.T. OZAN The paper by Dr J.N. van der Merwe makes an important contribution to the design of bord-and-pillar workings in the Vaal basin. It has been recognised for some time that the strength of coal seams in the Vaal basin is markedly lower than that of coal seams in other coal-mining districts in South Africa. However, there was insufficient data to quantify how much weaker the extensively jointed coal the Vaal basin is. A number of recent pillar collapses that occurred at Sigma colliery, the only remaining underground colliery in the Vaal basin, provided Dr Van der Merwe with an opportunity to make this assessment.

Jan 1, 1993

By K. I. Afewu, L. C. Woollacott

Little is reported in the literature that is directly useful for the interpolation film coefficients for the in-pulp adsorption circuits used in gold metallurgy. This can create a problem if the design or operation of these circuits is to be optimized by the use of simulation techniques. To address this problem, a study was undertaken on the influence of mixing intensity, scale, and geometry on the film coefficient in adsorption systems typical of the carbon-in pulp plants used for gold extraction. This, the first paper deals with the influence of these factors on the film coefficient and shows that the specific power to just disperse the carbon in the slurry is an important variable. This variable is also strongly dependent on mixing intensity, scale, and geometry-a dependence that is dealt with in the second paper in the series. From the informatlon obtained, practical scale-up procedures were developed. These procedures are considered to be applicable to resin-in-pulp as well as to carbon-In-pulp plants.

Jan 1, 1995

By J. A. C. Diering

All underground openings are three-dimensional, and in many cases it is not valid to analyse two-dimensional sections. This has been a problem in the past owing to the magnitude and complexity of three-dimensional stress analysis. In this paper a three-dimensional boundary element approach, using non-conforming quadratic elements, which is specifically applicable to underground excavations, is described. In addition, the philosophy of application of stress analyses is discussed. Three case histories are presented to demonstrate the practical nature of the approach as a tool in solving mining problems.

Jan 1, 1987

Gold Fields is the world?s fourth largest gold producer with operations in South Africa, Australia, Ghana and South America. All of Gold Fields? South African Operations are located in the Witwatersrand Basin and are intermediate to deep level underground mines exploiting gold bearing, shallow dipping tabular orebodies, which have collectively produced over 50 kt (1,608 Moz) of gold over a period of more than 100 years. Although the use of Monte Carlo as a business tool was introduced in 1964, it has only been in the last 30 years that it has gained increasing acceptance within the mining industry. However, the application thereof has been mostly limited to determination of risk in project areas. This paper however, considers the possibility of using Monte Carlo simulations to asses the underlying ?Root Cause? criteria critical to the operations management of existing mining operations. Currently, working operations have a distinct advantage over project areas as they have a wealth of historical information at hand. This, in turn, can be utilized to model distributions and relationships that can be used in Monte Carlo simulations, the results of which can be analysed to determine areas of concern. Projects can then be set up to ameliorate the effects of these and in turn reduce the risk of not achieving the operational targets. It is here that it must be stated emphatically that it should be the ?root causes? and the associated relationships that need to be emplaced within the model in order to achieve results that reflect the true causal relationship. The paper outlines possible sources of ?root cause? relationships and considers the outcomes of these in a case study on a large South African Gold Mine.

Jan 1, 2009

By J. O. Jensen

A method is described for the determination of cyanide in gold slurries, based on amperometry. The measured current is proportional to the concentration of cyanide, and is not effected by pH or by the concentration of oxygen in solution. It is also unaffected by other ions that may be present in gold-leaching solutions, including sulphide, thiocyanate, and thiosulphate. The current depends on the temperature, and an activation energy of 17,9 kJ/mol was determined Since the current is controlled by the mass transfer of cyanide to the anode, it depends on the conditions of agitation. In tests on an operational gold plant, slurry was pumped directly from the top of the leaching tank, through the measuring cell and back into the tank. The results indicate that the instrument is a promising alternative to the instruments currently available. The readings from the instrument remained in calibration for at least two days, showing that the instrument would need to be re-calibrated by the operating staff at regular periods.

Jan 1, 1994

By M. B. Algeo, R. H. A. Plaistowe

A method of forecasting the haulage trucks required for a large open-pit operation is described. Emphasis is placed on the effects of changes in planning and on the complexities of a mining operation that involves many benches and dumping areas.

Jan 1, 1979

By M. M. Oosterveld

Diamonds are mined from ancient raised beach deposits in southern Namibia where complex geological controls have resulted in patchy diamond distribution, largely related to irregularities (trapsites) in the bedrock. The distribution of the number of diamonds per sample is a discrete, reverse- J shape distribution which can be characterized by two parameters. These parameters have been transformed into a Beta and Theta Contribution which can be interpreted as reflecting the 'quantity' and 'quality' of the trapsites. The relationship of statistical parameters, obtained during the sampling of an ore deposit, to the geology of the deposit is an important element of ore reserve estimation. The large-scale regional trends in the contributions have been explained in terms of the geology.

Jan 1, 1987

By N. C. Joughin, A. C. Buckmaster

The use of face conveyors in gold mines by N. C. JOUGHIN. B.Sc. (Eng.). Ph.D. (Wits) (Member) and A. C. BUCKMASTER; M.A. (Cantab.) A mechanized stope-cleaning system has been developed around an armoured face conveyor, which was tested on the surface and in two underground trials. In the second underground trial, an average face advance of 8,5 m per month was obtained with a labour productivity of 27 ca/worker/month on a two-shift blast cycle. Two new face cleaning systems have been built, each incorporating an armoured face conveyor, a loading plough, a collapsible self-advancing barricade, and an integral roof-support system. These are about to be tested. A new type of reciprocating flight conveyor is being developed for stope use. This is cheaper, lighter, and more compact, and exhibits better wear characteristics, than an armoured face conveyor. In the early stages of the trials, this conveyor frequently achieved a singleshift blast cycle. It should be possible to achieve face advances of up to 40 ca/worker/month with a consistent one-shift blast cycle. The use of drill rigs and a self-advancing roof-support system would improve the productivity to over 50 ca/worker/month.

Jan 2, 1976

By R. S. Sanders, J. Schaan

Syncrude Canada Ltd. produces synthetic crude oil from Canada?s vast oil sand reserves by mining the oil sand, then separating and upgrading the ultra-viscous crude oil, or bitumen (~ 106mPa s @ 10ºC). At Syncrude?s Aurora Mine, about 16 000 tonnes oil sand per hour are mined and then transported 5 km by slurry pipeline to the extraction plant. The waste tailings stream is then transported about10 km by pipeline to a settling/sand storage basin. Oil sand slurries are reasonably concentrated (> 35%solids by volume), typically have a sand particle diameter between 0.18 and 0.3 mm, and are transported at reasonably high velocities (3 to 5.5 m/s). As one would expect, pipeline wear is a significant problem in this industry, in terms of both unplanned production outages and maintenance costs. In order to develop strategies to extend pipe life and to focus more on condition-based maintenance scheduling (as opposed to preventative maintenance), Syncrude has implemented an ongoing pipe wear measurement programme. Regular measurements of pipe wall thickness are obtained at various circumferential positions at a number of axial locations along each pipeline, using an ultrasonic scanning technique. In this paper, we show how wear rates vary as a function of axial location and circumferential position for oil sand hydro transport and coarse particle tailings pipelines. The specific positions at which peak wear rates occur are explained by considering the characteristics of the coarse particle slurry flows to which the pipelines are exposed.

Jan 1, 2007

Council and Standing Committees - 1981/82 President: G. Y. Nisbet. Senior Vice-President: Prof. A. N. Brown. Junior Vice-President: Prof. R. P. King. Honorary Treasurer: Prof. D. G. Krige. Immediate Past President: Dr P. R. Joehens. Members of Council: B. C. Alberts, J. D. Austin, P. T. Fewell, C. E. Fivaz, J. J. Geldenhuys, Dr A. K. Haines, P. N. Harris, H. E. James, C. G. Knobbs, Dr B. K. Love¬day, Dr J. Lurie, C. S. MacPhail, D. G. Malan, J. C. Mostert, G. C. Thompson, Dr H. Wagner. Chairman, Witbank/Middelburg Branch: B. Rohrmann. Chairman, Orange Free State/Klerksdorp Branch: K. F. W. Eick. Chairman, Materials Engineering Specialist Division: G. Pienaar. Past Presidents serving on Council: Dr M. G. Atmore, H. Britten, Prof. D. D. Howat, Dr J. P. Hugo, D. G. Maxwell, Prof. R. P. Plewman, Dr R. E. Robinson, Prof. M. D. G. Salamon, P. W. J. van Rensburg, D. A. Viljoen, P. A. von Wielligh. Standing Committee Chairmen: Constitution, Rules and Policy, Dr P. R. Jochens; Membership, Prof. R. P. King; Training, Career Guidance and Education, P. A. von Wielligh; Journal, Prof. A. N. Brown; Monograph Series, D. G. Malan; Technical Programme - Metallurgy, C. E. Fivaz; Technical Programme - Mining, P. N. Harris; SAIMM Schools - Metallurgy, Dr B. K. Loveday; SAIMM Schools - Mining, J. D. Austin; 1982 CMMI Congress, Dr M. G. Atmore; Awards, Dr P. R. Jochens; Adjudication, Dr P. R. Joehens; Phoenix National Committee, Dr M. G. Atmore; Excursions, J. C. Mostert; Mines and Works, Prof. A. N. Brown; World Mining Congress - National Committee, Prof. R. P. Plewman.

Jan 1, 1982