Search Documents

By Haiping Sun, Samir Ganguly, Oleg Ostrovski, M. Yaser Lone

Wettability of graphite by synthetic SiO2-Al2O3-CaO-MnO slags with varied MnO content and by industrial slags was studied at 1350-1600 °C using sessile drop method under argon atmosphere. Initial contact angle was the lowest (110-115o) for the MnO-free slag. For slags with 10-40 wt% MnO, the initial contact angle was in the range 125-135o. The contact angle decreased with the contact time. The change in the contact angle with slag mass was found insignificant. The surface tension of slags obtained from the drop shape analyses was 500-800 mN/m and varied in a narrow range with temperature and MnO concentration. The reduction rate increased with increasing MnO content in the synthetic slag from 20 wt% to 40wt% and temperature. Increasing temperature also increased the rate of reduction. No correlation was observed between the reduction rate and MnO content in the synthetic slags in the range 0-20 wt% and in the industrial slags. The rate of SiO2 reduction from the molten slag was close to the rate of MnO reduction. The MnO-free slag had the largest contact area with graphite substrate. Keywords: reduction, wettability, graphite, slag, manganese, surface tension.

Jan 1, 2007

By J. A. Bakken, M. T. Jonsson, G. A. Saevarsdottir, H. Palsson

The electrodes of a Submerged Arc Furnaces carry a high current and are subject to enormous stresses caused by both the electric arc itself, and the current distribution within the electrode. The external effect of the arc on the electrode is treated in a different paper at this conference, The purpose of this paper is to analyze the thermal effects of ohmic heating within the electrode at the arc attachment on the carbon based electrode, using data for Søderberg electrodes. The thermal conditions are then used to examine stress conditions in the vicinity of an arc. Two types of models of an electrode are presented in the paper. The first type is an accurate finite element model, based on both two and three dimensional elements and the second type is an one dimensional model, providing better insight into the problem. For the second type, a spherical model of thermal conditions in a semi-infinite solid has been developed. Results show that the electrode surface is heated quickly up to a maximum temperature and for a specific test case, the surface can only withstand the load for about 10 seconds. Also, the thermal stresses on the surface are very high which will increase erosion on the surface in addition to normal evaporation.

Jan 1, 2007

By J. Talja

Keywords: drying, steam drying, concentrates, copper, lead During the past twenty years steam drying has become a prominent technology for drying of non-ferrous metals concentrate. This is mainly because of its low energy consumption and very low emissions. The first applications of significant capacity were stationary steam dryers, which however, faced severe challenges in maintenance costs and availability. That technology was soon replaced by Kumera?s rotary steam drying technology, which has been the dominant technology in new dryer installations world-wide for the past ten years, ever since the first installation in Hamburg in 1999. There are ten Kumera steam dryers in operation today and five more to be commissioned during 2011. Practically every dryer is different owing to continuous development, new innovations and operational experience with continuous feedback from the operators. Most significant improvements relate to capacity increase with the Kumera steam-dryer family, new feeder systems at the wet end, a completely new design of the dry material discharge with increased availability, heating element design and material selection, and control systems. This paper discusses the modifications and improvements introduced which have enabled the Kumera steam dryer to become the global leader in new dryer installations.

Jan 1, 2011

The paper provides a brief review of a multivariate uniform conditioning and a localized multivariate uniform conditioning (LMUC) technique, and presents a production reconciliation case study based on a porphyry copper-gold deposit in Peru. The reconciliation study compares the longterm LMUC mineral resources model (typical of new mining projects, which are invariably based on drilling data on a relatively large grid) to the corresponding production blast-hole grade control model, as well as the final plant production.

Jan 1, 2014

By I. Matsunaga, K. Aoki, W. -j. Jung

Blasting is widely used in mining and basic construction because of its speed and economy to destroy the rocks. Blasting has the advantages of reduced excavation costs and shorted construction time when compared to the use of heavy machinery for excavation and cutting such as that with a tunnel boring machine. There are numerous problems with blasting, including the noise, vibration and fly rock. So it is necessary to accurately evaluate fracture mechanics of rocks on the dynamic loading condition to control the fracture process of the blasting. The tests using Hopkinson's effect for the dynamic condition using the precise detonators were performed for various strain rates on three different kinds of rocks. In the tests using Hopkinson's effect for the dynamic condition, the high-speed camera was used to observe the fracture process of the test sample rocks. As the results of experiments there was an increase in the tensile strength of rock with an increase in the strain rate for three kinds of rock on the dynamic loading. The tensile strength of rocks with high porosity on the water saturation condition was decreased on the both static and dynamic condition. It is clear that the strain rate and water saturation were influenced to the tensile strength of the rocks.

Jan 1, 2003

By M. C. Bhulose

Paper written on project work carried out in partial fulfilment of B. Eng (Mining Engineering) degree The purpose of this project was to identify constraints that could occur in the current sub-decline shaft at Turffontein Shaft should an increase in production take place. Particular attention was to be paid to the transportation of men and materials and to the broken rock and ventilation capacity of the shaft. This project is an in-depth evaluation of the logistic capacity of the sub-decline system at Turffontein Shaft in order to determine by how much production can be increased in this area to replace tonnages from the vertical shaft area, where ore reserves are rapidly becoming depleted.

Jan 1, 2004

A localized nonlinear recoverable resource estimate technique has been applied using typical feasibility or new mining drilling data configurations drawn from a massive database from a mined-out area on a hydrothermal gold deposit. The results were then compared with the corresponding 8 m x 5 m grid grade-control data in order to determine the efficiency of the approach and the validity of the recoverable resource estimates for mine planning and financial forecasts.

Jan 1, 2014

By M. Abdellatif

Keywords: Magnesium, pyrometallurgy, Mintek Extensive testwork on atmospheric thermal magnesium production has highlighted certain important fundamental and operational factors that have a major influence on magnesium extraction and its extraction rate, the condensation efficiency of magnesium, as well as on the quality of the condensed metal. The possible impact of these factors on the selection and preparation of raw materials, recipe choice, furnace electrical energy consumption, and on the refining requirements of the crude magnesium is discussed. Selected pilot plant operational and metallurgical data are also presented.

Jan 1, 2006

By I. W. van der Merwe

Recently, a new kind of filtration has emerged, namely nano-filtration (NF). It is a membrane-based process which exhibits totally unique separation characteristics for dissolved salts as well as for many non-charged species. By exploiting the particular separation characteristics of this new membrane type, many unique and novel separations have been made possible. The basis for separation by nanofiltration is the negative surface charge of the membrane. This results in rejection of multivalent anions, whilst associated cations are also rejected to maintain electro-neutrality. This peculiar property enables separation of dissolved ions such as sulphate and copper from acid, whilst the acid may be purified for reuse. This paper aims at providing an overview of the principles of nanofiltration, illustrated by particular examples.

Jan 1, 1998

By A. V. Roschin, N. V. Malkov, V. N. Karnoukhov, V. E. Roschin

Reduction interactions in solid phases are widespread and occur in most complex metallurgical processes. Among these processes, reactions between oxides and carbon have a special importance. The authors conducted experiments for comparison of reduction by different reducing agents of impregnated chromite ores, in which grains of the reducible chromite spinel are isolated from direct contact with the reducing agent by layers of non-ore material. The results of the experiments have revealed that the beginning of reduction is preceded by thermal and impurity order-disorder transformation of the oxide lattice whilst the transformation of the oxide lattice into the metal lattice takes place as a result of removal of oxygen anions from the zone of metal germ nucleation. Since anions are charge carriers, increase of their mobility can be monitored by changes in electrical conductivity of oxides. Respective measurements of electrical resistance of ores of different metals and a number of pure refractory oxides under heating have indicated that the beginning of reduction coincides with the time of drastic (tens of thousands times) increase of conductivity of the oxides. Besides, the temperature of the beginning of carbon-thermal reduction is in line with the Tammann temperature, i.e. the temperature of transition from the predominantly surface diffusion to volume diffusion. Segregation of metals from the oxide lattice occurs as a result of merging of anion vacancies with defect electrons on defects of the oxide lattice. The transformation of the oxide lattice into the metal lattice requires a certain concentration of anion vacancies and inflow of electrons from the reducing agent to the site of metal segregation. Such inflow has no difficulties due to the mixed anion-electron nature of high-temperature conductivity of oxides. Thus, the reduction is not determined by oxygen diffusion, it is determined by oxygen vacancies diffusion whose speed exceeds the speed of oxygen diffusion by orders of magnitude. This determines that the kinetics of reduction considerably exceeds the kinetics of oxidation at similar temperatures since oxidation proceeds by means of mass transfer of oxygen through the layer of the generated oxide.

Jan 1, 2004

By R. Sullivan, K. Joiner, B. Emery, M. de Vries, F. A. Stober, L. R. Nelson, J. M. A. Geldenhuis

Keywords: Pyrometallurgy, smelting, converting, furnace design, furnace retrofit, high-intensity smelting, copper coolers, plate coolers, waffle coolers, tap-blocks, lower sidewall air-cooling, wall hold-down system, platinum group metals, ferroalloys, ferrochrome, ferrocobalt, ilmenite smelting, ironmaking, operational readiness, operational support The paper describes the development of furnace designs by Hatch in conjunction with the smelting plants in Africa to meet the intense process requirements in certain applications; continued improvement in operating efficiency through increased throughput from existing crucibles; and improvement in campaign life and furnace integrity. The era of Hatch in Africa has seen the doubling of furnace power in retrofit projects using existing crucibles to developing the highest intensity immersed electrode operations in the world. This has resulted in minimized OPEX and CAPEX per unit of production. Through the continued development of its cooling, binding and furnace power supply technologies and working with the experienced and knowledgeable personnel at the smelting facilities in Africa, Hatch has managed to meet the challenges of ever increasing furnace process requirements associated with increased power density and superheats prevalent in the operations. In addition to developing furnace crucible designs, Hatch has also intensified its ?after sales service and support? with the construction, commissioning and start-up technical assistance and operational readiness and operational support for ramp-up to nameplate capacity and beyond. The key areas of furnace risk associated with high superheat molten material tapping has also seen the development of diagnostic systems to mitigate risks and produce early warning signals for the operators.

Jan 1, 2006

By V. Coetzee

Keywords: Pyrometallurgy, furnace, PGM, platinum, nickel, copper, electric smelting, six-in-line, Peirce-Smith, Impala Platinum In 1992, a paper was compiled highlighting a common-sense approach to electric smelting at Impala Platinum. Since then, the smelter complex has undergone considerable changes. Mineral economics, UG2 exploitation, and changing environmental legislation have enforced numerous process upgrades, yet a common-sense approach has always been adopted. This document details the major changes in the smelter complex at Mineral Processes (Minpro) over the past 15 years, and provides the rationale for the changes.

Jan 1, 2006

By J. Ndlovu, R. Hundermark

Keywords: Anglo Platinum, Polokwane Smelter, pyrometallurgy, metallurgy, platinum, platinum group metals, PGM, base metals, nickel, copper, sulphide smelting, electric furnace, Söderberg, electrode, matte, slag, flash drying, matte casting, crushing, granulation Anglo Platinum?s Polokwane Smelter is situated outside Polokwane, in the Limpopo Province of South Africa. Wet concentrate is received from various concentrators along the Eastern Bushveld Complex, with 60% of the total concentrate received being from UG2 reef and 40% from Merensky reef. The concentrate grade differs from 35 g/t to 110 g/t, and from this a PGM-rich nickel-copper matte is produced. The furnace matte produced is sent to the ACP converter in Rustenburg. The Anglo Platinum concentrators, from which concentrate is received, are Lebowa, Potgietersrus, Amandelbult, and Union, as well as the joint venture Modikwa. The concentrate is fed to two flash dryers that utilise coal-fired, fluidized-bed hot-gas generators to produce the hot gas that will drive off the moisture, leaving a fine bone-dry concentrate to feed to the furnace. The dry concentrate is pneumatically transferred to a storage silo before being transferred to the feed bins situated above the furnace. Lime, if required as a flux, may be transferred separately to the furnace feed bin by a pneumatic system. The concentrate and lime is fed from the feed bins onto airslides and into the furnace. The feed rate is automatically controlled, and the system is set up to optimize the power to feed ratio. The electric furnace is nominally rated at 68 MW and the power is transferred into the furnace using six 1.6 m diameter Söderberg electrodes. Concentrate is melted by energy generated when electric current passes through the electrodes and resistive slag layer. On melting, two immiscible phases form: slag and matte. Furnace matte, containing the bulk of the base metal sulphides and PGMs, is denser than slag and collects naturally at the bottom of the furnace. The furnace is constructed of a combination of refractory brick and water-cooled copper coolers. The furnace sidewalls and hearth are cooled by air drawn through the area by cooling fans. The hearth and matte zone are constructed from refractory bricks. The copper coolers reside only in the slag zone of the furnace along the entire perimeter of the furnace. One staggered row of plate coolers is installed above the waffle coolers along the perimeter of the furnace. Matte is tapped periodically through one of the two matte tapholes into 35-ton refractory-lined ladles, and cast into matte ingots on a casting machine. The cooled matte is discharged onto a concrete slab for cooling and then transferred by front-end loaders to the crushing plant. The matte is first crushed in a jaw crusher and then a Rhodax cone crusher to a size of 2 mm before it is loaded into tankers and sent to the ACP. The low-grade slag is tapped from the furnace through a water-cooled copper insert into a short water-cooled copper ?hot launder? which discharges into a granulation cold launder. The granulated slag slurry flows to three rake classifiers, from which the coarse slag is discharged onto a conveyor to dewatering silos. The dewatered slag from the silos is dumped. The water overflow from the classifiers reports to two thickeners where the water is clarified, and the thickener underflow is returned to the rake classifiers. The smelter is a zero-effluent plant and all the water from the slag silos where the slag is dewatered, as well as the storm water, is pumped to the process water dam from where it is pumped back into the plant for process water use. The off-gas from the furnace is drawn through a forced draught cooler and into a high temperature baghouse. The dust collected in the baghouse is pneumatically transferred into bins above the furnace and is fed via the concentrate airslides. The cleaned off-gas is then vented through the main stack.

Jan 1, 2006

By M. Yavuz

One of the challenging problems for optimization in mining operations is to choose the best equipment among the alternatives. Equipment selection is an important task for mine management due to its operational cost, and is also an integral part of mine planning and design. Equipment selection is not a well-defined process because it involves the interaction of several subjective factors or criteria. Besides, decisions are often complicated and may even embody contradictions. Therefore, equipment selection is considered as a multi-criteria decision-making process, and suitable decision-making methods should be employed in this process. In this study, the loader selection for Aegean Lignite Colliery was made by using both the analytic hierarchy process and Yager’s method. Owing to the misusage of Yager’s method in the past, a new procedure is proposed in this paper for making proper decisions. It is highly recommended in this purposed method that criteria or alternatives should be grouped so as not to exceed the limitations of human performance (nine criteria/alternatives). The most appropriate solution for the loader selection was investigated by obeying this limitation for each method, and the results were compared. At the end of the decision-making process, a sensitivity analysis was applied for each method in order to see how a criterion affects the final decision. The advantages and disadvantages encountered during the application of each decision-making method are presented.

Jan 1, 2015

By L C. Pretorius

Pipe pigging is a technique for the in situ (field) coating application, to create a seamless internal anti-corrosive lining of long pipelines. The technology originated in the cleaning of pipes, and these proven cleaning methods continue to be used today. Firstly mechanical cleaning of the pipeline is performed, using wire brush, razor back, course stud and fine wire pigs, then foam pigs, or criss cross pigs, and urethane blade scrapers to remove loose debris, wax, residual hydrocarbons and corrosion products from the pipeline. Part of the proprietary techniques and expertise is to ensure that these cleaning pigs do not get stuck Next chemical cleaning of the pipeline is performed, using repeated pig runs with detergents, solvents, acid etching, corrosion inhibitors, consecutively batched between two pigs, to ensure a clean, dry metal finish to a visual cleanliness standard of ISO SA2½. These in situ techniques were developed, 40 years ago to apply internal corrosion protection to pipes using a thin layer of epoxy based paint (50 to 100 micron). Until recently these old techniques were never improved upon. Although many thousands of kilometres of pipes were successfully coated with these thin film epoxy based paints and old application techniques, these thin paint films had problems in weld coverage, and were also unable to fill pits caused by pitting corrosion, and unable to replace metal loss caused by channel erosion. New coating material developments, revised application methods and modified pigging equipment have now made it possible to apply thick film coatings as corrosion barriers to the internals of pipes in the field, using these pigging techniques. The thick coating films can be up to 1 mm (40 mils) thick in a single coating run over long distances. The new thick film coating materials and application techniques are similar to continuous screeding, creating a far more robust seamless internal pipe lining when compared to the old technology of thin film paints. With thick film polymers the option now exists to create a structural GRP pipe within a pipe, be it steel or cementicious. It has been preferable, even necessary, to move away from the traditional epoxy paints and coatings. It was found difficult or impossible to use epoxy materials for these pipe coating applications due to the requirement for achieving a suitable viscosity with adequate hold up. In order to reduce epoxy viscosity a solvent or reactive diluent is required. This inevitably lead to solvent entrapment and poor cure characteristics in cold climates. Further mud cracking in over thick areas, the inability to extend or reduce pot life, poor control of cure time and limited resistance to aggressive or chemical environments made solvent based epoxy resins a poor choice.

Jan 1, 2006

By J. Kempken, R. Degel, J. Kunze, R. König

The FeNi technology is currently dominated by high-power submerged arc furnaces, often designed as smelter as "two-inline-solution". To achieve the intended high efficiency, state-of-the-art design in good correlation with ores and reductants and an integrated layout of the whole plant is of great importance. An introduction will be given to general aspects in the production FeNi, plus a detailed overview of design principles for large FeNi smelters and finally some examples of innovations and research projects concerning Fe-Ni.

Jan 1, 2007

By G. van Hout, D. Rahal

Caving is a mass mining method that is normally applied to large, low grade orebodies because of its low production cost and high capacity. However, equipment breakdown and poor draw management can cause mining costs to exceed that of all other mining methods. One way to minimize the effect of disruptions in the mining cycle is to use Mixed Integer Linear Programming (MILP) for long-term scheduling. This paper describes a MILP goal program which has the dual objectives of minimizing deviation from the ideal draw profile while achieving a production target. Schedule optimization is performed using a life of mine approach in which all production periods are optimized simultaneously. The underlying assumption being that material mixing in the short-term (between monthly optimization cycles) has a minimal effect on the long-term state of the panel. Schedule optimization is carried out using six general constraint types to model and control production. The constraint types define: deviation from ideal practice, panel state, material flow conservation, production quality, material flow capacity and production control. These constraints define production targets and drive production toward the ideal profile while maintaining correct mining practice. Application of the model using production scheduling data for a De Beers kimberlite mine. It is shown how different production control constraints regulate production from individual drawpoints as well as recovery of the ideal panel profile by implementing an optimised draw schedule.

Jan 1, 2003

By B. Andresen, S. T. Johansen, H. Tveit, S. Grådahl, B. Ravary

The Norwegian ferroalloy industry has high ambitions regarding environmental standards. Basic research work has been performed to improve the fundamental understanding of ferroalloy processes and the environ-mental aspects. This paper will present work dealing with the understanding of formation and control of NOx, PAH and dioxins. During this work various techniques and methods have been applied, such as comprehensive industrial measurements, laboratory experiments, model development and application of Computational Fluid Dynamics (CFD). The main goal has been to reduce the environmental impact of ferroalloy plants, by means of improving the combustion processes done by introducing new charging routines and optimized furnace operations, instead of installing expensive gas treatment systems. The Norwegian obligations in accordance with the Gothenburg protocol are to reduce the NOx emissions by 30%, compared with the 1990 level within 2010. Measures developed in this work have resulted in 40-60%reduction in NOx emission, and major reductions in PAH and dioxins for ferrosilicon and silicon metal plants. This has been achieved by introducing semi continuous charging and improved furnace operations. Semi continuous charging and optimized furnace operations are shown to reduce the blowing activity (i.e. emission of large quantity of SiO over the charge by direct channelling from the crater zone). It also reduces variation in off-gas temperature and dust production. To understand the processes and to achieve our results we have used online equipment, with fast sample rates and response times, to measure the off-gas compositions and temperatures. Most of the measuring techniques used are based upon optical principles making use of the absorption- and emission spectrum of the gases. In addition a new prototype instrument is developed for continuous measurement of off-gas characteristics, total dust amount and off-gas temperature. The presented work is a result of a long term co-operation research and development teamwork, between the industry and the research community, and has improved both the process and reduced the emissions. The work has introduced new process design and operation standards, and has resulted in ferroalloy production with better environmental standards.

Jan 1, 2007

By J. Gummer, M. Williams, S. J. Hawksworth

A common problem encountered in British coal mines is bearing failure on conveyor system idler rollers, which on occasions has led to fires. The UK Mines Inspectorate initiated a study of such failures to assess the potential for ignition of explosive atmospheres. As part of this study HSL have developed a system to measure the temperatures generated within the bearings during controlled failure. Temperatures are measured using both infrared thermal imaging and contact thermometry. The work to date has shown that temperatures well in excess of the auto-ignition temperature of methane can occur.

Jan 1, 2003

By D. Yu. Paleev, O. Yu. Lukashov, A. Yu. Krainov, E. R. Shrager, I. M. Vasenin

The gas-dynamic method is presented of calculation of explosion-proof distances during an explosion of the methane-air mixture in mine working. On the basis of this method is modelled of shock waves interaction with explosion protective parachute partitions, obstructions and water barriers. Calculations have been carried out of attenuation factors of shock waves during their interaction with explosion protective structures, arranged near conjugation zones of mine workings. Possibilities have been analysed of suppression of intensity of shock waves and of propagation of shock waves control in mine working network of coal mines by installation of explosion protective structures.

Jan 1, 2003