Search Documents

By C. M. Mason

Bureau of Mines studies were made on the sensitivity of several ammonium nitrate-fuel oil (AN-FO) mixtures to bullet impact. The experimental work was done with one military rifle and two high-velocity sporting rifles with a variety of ammunition. For the three rifles used, the order of efficiency in initiating detonation in AN-FO mixtures was 220 Swift >300 Weatherby Magnum >30-&apos;06. The velocity of the bullet was found to be a decisive factor in the initiation. The sensitivity of various materials studied increased as follows: Clay-coated prills with 4 percent oil <fresh surfactant-coated prills with 4 or 6 percent oil <surfactant-coated prills with 4 or 6 percent oil and aged 270 days <crushed prills with 6 percent oil <very low-density, surfactant-coated prills (micronized), with 4 percent oil.

Jan 1, 1963

By R. F. Abernethy

A chemical method of determining microgram quantities of arsenic in coal was investigated by the Bureau of Mines to supplement a semiquantitative spectrographic method of determining arsenic in coal ash. In accordance with a method recommended by the International Organization for Standardization, 1-gram samples of coal are decomposed by wet oxidation with boiling sulfuric acid (H2S04) and nitric acid (HN03) to remove the organic matter. After heating to fumes of SO3 to remove HN03, the arsenic is separated as arsine by the action of zinc in H2S04 solution. The arsine is absorbed in dilute iodine solution in which the arsenic is determined colorimetrically by the molybdenum-blue reaction. Two modifications of the method for obtaining the arsenic in solution, in addition to the wet oxidation method, give satisfactory results. The modifications are (1) furnace ashing with MgO added to the coal, followed by treatment with H2S04, and (2) extraction of arsenic from the coal by dilute HNO3 without ashing. Float-and sink-tests show that arsenic is associated mainly with mineral matter in the three coals examined. High-temperature ashing tests show that very little arsenic is volatilized from coal ash below 1,000° C, but it is virtually all removed from the ash at 1,300° C.

Jan 1, 1968

By Maria I. De Rosa

Table 1 and figure 1 show the number of fires and fire in¬juries that occurred in underground coal mines by state during 1990-1999. Table 1 also shows by state the risk rates, employ¬ees&apos; working hours, lost workdays, and coal production. Over¬all, 87 fires occurred in 12 states. Twenty-seven of those fires caused 34 injuries (the yearly average was 8.7 fires and 3.4 injuries). One fire and one injury involved a contractor. The underground mine fires required 25 mine rescue team interventions and 30 mine/section evacuations followed by 13 mine/section sealing/flooding/CO2/N2, gas injections. The Ewhr value was 1,003 x 106 hr (In = 0.007), the CP value was 4,008 x 106 st (Frr = 0.022), and the LWD value was 208. Virginia had the most fires (15 fires and 7 injuries). Pennsyl¬vania had the most fire injuries (12 fires and 9 injuries), fol¬lowed by Kentucky (12 fires and 6 injuries), and Alabama (12 fires and 4 injuries). Among these states, Alabama had the highest fire risk rate value (Frr = 0.073), whereas Pennsylvania had the highest injury risk rate value (In = 0.016). Table 2, partly illustrated in figure 2, shows by time period the number of fires, fire injuries, risk rates, employees&apos; working hours, lost workdays, and coal production. The number of fires and fire injuries show a decrease followed by an increase during the five time periods (see table 2 and figure 2). This was ac¬companied by a decline in employees&apos; working hours throughout the periods and an overall small decrease in coal production. The In and Frr values follow patterns similar to those shown by the fire and injury values. By comparison, data from Pomroy and Carigiet [1995] show that during 1978-1992 a total of 11 states were involved in 164 underground coal mine fires (yearly average, 10.8) with 43 injuries (yearly average, 2.9) and 27 fatalities (yearly average, 2; however, the 27 deaths occurred during a single fire caused by an overheated air compressor [MSHA 1984]). The CP value was 5,340 x 106 st (yearly average, 356 x 106 st) (Fn = 0.031). Data on employees&apos; working hours and injury risk rates were not available. Tables 3-8 show the number of fires by ignition source, method of detection and suppression, equipment involved, location, and burning material by time period. Figure 3 shows the major variables during 1990-1999. Table 9 shows the number of fire injuries per number of fires causing injuries and total fires by year, ignition source, equipment involved, and location.

Jan 1, 2004

Eliminate accidental tramming of a cleanup tractor. Approach A switch was installed in the operator&apos;s seat cushion to pre-vent the cleanup tractor from tramming without an operator in the driver&apos;s seat. How It Works The operator must be seated, and the Forward/Reverse Switch (that controls tramming direction) must pass through the NEUTRAL position before the vehicle will tram. See Figure 1. A pressure-sensitive seat cushion switch, a solid-state relay, and a double-contact relay were added to the control circuitry of an S & S BMUAT -88 cleanup tractor to create this tramming interlock. The weight of the operator on the cushion closes the seat cushion switch (Figure 2, A). This activates the solid-state relay (B), which completes the initial circuitry. Moving the For- ward/Reverse Switch (C) to NEUTRAL energizes the coil in the double-contact relay (D) and closes both contacts. One contact completes a sustaining circuit which keeps the double-contact relay energized. The second contact transfers power to the remaining contacts within the Forward/ Reverse Switch. These circuits are shown in greater de- tail in Figure 2.

Jan 1, 1978

By C. L. Severy

On the Pacific coast during World War II, a tremendous ship-building industry was developed, Early in the war it became impossible to obtain in- got or steel scrap for ship ballast. Magnetite, an oxide of iron, was sub- stituted as it fulfilled the requirements of weight for available space in the ships. Consequently, a new use for the western magnetite was rapidly developed.

Jan 1, 1948

By Oliver Bowles

"A New Mica Company in China A report has been received from the American Consulate at Chungking, China, to the affect that a new company has been organized to operate a mica mine north of Ta-chien-lu, in the province of Ssu-Chuan. The company, which is entirely under Chinese management and control, has a working capital of $10,000. While comparatively new, the mine has been worked before, and apparently with some success. The mica is said to be of good quality. It is claimed that the deposit will supply a limited amount of mica that will cut in pieces a foot square or over, and larger quantities of smaller sizes. The chief difficulty is transportation, for it is reported that a ten days' journey, part of it over mountain trails, will be necessary to transport the mica from the mine to Yachow, the nearest practical waterway. It is probable, therefore, that the output of the mine will be limited.Necessity for Careful Trimming and Grading of MicaA recent report to the Department of Trade and Commerce, Ottawa, Canada, by Acting Trade Commissioner C. G. Venus, London, England, contains information which is of vital interest to mica producers in the United States. It is pointed out that mica exports from Canada to England show a gradual decline dur¬ing recent years, the figures being as follows: 1913- 1,383 cwt: 1914 - 1,225 cwt: 1915 - 1,864 cwt: 1S16 - 879 cwt: 1917 444 cwt: 1918 - 480 cwt. Shipments from India to England, on the other hand, show a steady increase from 40,178 cwt. in 1913 to 66,401 cwt, in 1918."

Jan 1, 1920

By R. P. Beyer

As part of its thermodynamic investigations of mineral compounds, the Bureau of Mines has written an algorithm based on Newton&apos;s method for solving for the characteristic Debye temperature of a compound, from heat capacity and temperature data. A listing of a FORTRAN IV program based on this algorithm, for calculating Debye temperatures given heat capacities or for calculating heat capacities given Debye temperatures, is available from the author upon request.

Jan 1, 1981

Develop a method of dewatering ultrafine mineral waste that will increase water recovery from the waste and produce a dewatered material that eliminates the need for large settling ponds. Background In the hydrometallurgical treatment of many ores and concentrates to recover mineral values, slurries of fine particles are generated. Some of these slurries settle slowly and are difficult to dewater. This inherent property causes environmental and handling problems for the minerals industry. Examples of such problem wastes are clay wastes generated during the mining and beneficiation of phosphate ores, the processing of coal to produce a low-ash material, the cleaning of bentonite, beneficiation of potash, and the recovery of mica from clay-containing ores. At the present time these waste slurries are treated by techniques such as impoundment, thickening, and thickening followed by filtration. But factors such as new environmental regulations, the loss of mineral values in the waste slurries, the need to recycle water in the processing facility, and the lack of land suitable for impounding the waste have shown that new technology will be needed in the future to handle waste slurries.

Jan 1, 1986

By Robert H. Schutz

This publication lists and describes devices approved jointly by the Secretary of Interior and the Secretary of Health, Education, and Welfare, under the provisions of [§]70.300-1, Part 70, Subchapter 0 of Chapter I, Title 30, Code of Federal Regulations (35 F.R. 5548, April 3, 1970), for use as respiratory protection against respirable pneumoconiosis-producing dusts. Included are type C supplied-air respirators approved under Bureau of Mines Schedule 19R and dust, fume, and mist respirators approved under Bureau of Mines Schedule 21B.

Jan 1, 1971

By H. G. Lucas

A feeder screw supplied at constant pressure by a hopper-orifice arrangement was developed for feeding solids in size ranges up to several hundred micrometers at constant flow rates. Performance of the feeder was evaluated by measuring the flow rates obtained with 3-to 7-micrometer coal ash, 70 percent through 200-mesh coal, and minus 325-plus 400-mesh coal ash. Constant feed rates within a few percent of set values were achieved for half-hour periods for the larger particles and for 5-minute periods for the finer particles. Suggestions are given for feedstock preparation and feeder operation for optimum performance.

Jan 1, 1974

Prevent the propagation of a fire and control the spread of smoke and toxic gas in underground mines. Approach A fire door suitable for large openings in underground noncoal mines and providing protection for openings requiring 11/2 hours of fire resistance, a 250°F maximum temperature rise, and high pressure differentials was de-signed, laboratory tested, and in-mine tested. How It Works The door is a double-acting swing type. Its two panels. connected by an overhead linkage, open in opposite directions. Consequently, high pressure differentials across the door have little effect on the force required to open and close the door. The door is constructed of 14-gauge sheet steel skins welded to both sides of a 5-inch-wide steel channel frame. The frame is rein-forced with 5-inch-wide steel channels in a horizontal and diagonal pattern. The voids between the reinforcing members are filled with a ceramic fiber insulation material to limit the surface temperature rise of the unexposed side of the door during a fire. A fire -resistant neoprene-coated fabric is used to seal around the edges of the door panels. The door is opened and closed by an air cylinder, attached to the over-head linkage and operated by lanyards on either side of the door. The door design includes an optional airlock manway for drifts of adequate width.

Jan 1, 1983

By C. F. Swab

A relatively innocuous halocarbon was investigated as a substitute for the highly toxic carbon tetrachloride in the approval testing of chemical cartridges. The vapor effluent of 1,1,2-trichloro-1,2,2-trifluoroethane from chemical cartridges is continuously monitored by a nondispersive infrared analyzer. Breakthrough times for the cartridges, using the halocarbon, can be equated to those of carbon tetrachloride, if multiplied by the factor, 1.49.

Jan 1, 1970

A primary objective of the Surface Mining Control and Reclamation Act is to establish uniform national regulatory standards to protect the environment during mining and for reclaiming land after it is disturbed by current and future surface coal mining. In recognition of the wide range of climatic and geologic conditions in coal-producing areas, Congress provided that individual states may establish their own programs for regulating surface and underground coal mining and reclamation on private land. The standards for state programs must be at least as effective as the federal standards. Initial and Permanent Regulatory Programs Congress recognized the importance of establishing regulations to implement the Act as quickly as possible, while recognizing that the preparation of such complex regulations would be a lengthy process. Consequently, a two-phase schedule was established. An abbreviated initial program was put in place immediately, followed by a more extensive and detailed permanent regulatory program. The initial program regulations were published in December 1977, and mine permits issued by states after February 1978 were required to conform with those regulations. Regulatory provisions contained in the initial program included 12 basic performance standards, continuation of existing state permitting, bonding, and enforcement processes (although if those features did not already exist, they did not have to be added), a federal inspection frequency of once every six months, joint state and federal inspection and enforcement in states that had existing programs, and the prohibition of mining in the specific areas listed in the Act. Permanent program regulations were published in March 1979, following extensive review and comment from the public, including the coal industry and organized environmental groups. The regula¬tory provisions in the permanent program expanded those in the interim program by including the implementation of all performance standards contained in SMCRA, a new permitting process, a requirement for performance bonds, an increased inspection frequency (one per month), a new enforcement process, and a process for designating lands unsuitable for surface mining. The regulations for the permanent program have been revised several times since 1979; more revisions can be made as new mining and reclamation tech¬niques are developed. Such changes were anticipated by Congress; in fact, a provision in SMCRA for experimental practices encourages advances in mining and reclamation techniques.

Jan 1, 1992

By H. J. Heinen

A technique offering promise as a metallurgical processing sequence the recovery of molybdenum (Mo) from the sulfide mineral--molybdenite?was investigated. The method consists of two steps: (1) electrosynthesis of pure dimolybdenum carbide (Mo2C) from molybdenite (MoS2) and (2) interaction of Mo2C and molybdic oxide (MoO3) to produce pure molybdenum metal. Two molten salt systems were satisfactory for electrosynthesizing Mo2C. The first was a mixture of potassium chloride (KCl), potassium fluoride (KY), and sodium metasilicate (Na2SiO3), and the second consisted of sodium fluoride (NaF), KF, sodium tetraborate (Na2B4O7), and sodium carbonate (Na2CO3). Yields up to 0.42 gram of Mo2C per ampere-hour were obtained. The carbide, mixed with monitored amounts of MoO3, was converted to molybdenum metal of 99.9 percent purity by sintering at 1,500° C.

Jan 1, 1965

By Rudolf E. Greuer, Linneas W. Laage, Xinton Chang

All output is saved in the file MFIRE OUT m the di¬rectory and on the disk containing the program The file can be inspected with a text processor and sent to a print¬er, if needed CONTENTS OF OUTPUT FILE The comment lines, reference temperature, air densi¬ty, a table of the units of measure for the results, and the average values are shown at the beginning of MFIRE OUT All input data will be shown in the output file if LOUT on Control line number 1 is _<-1 For each contamination source, a new branch will automatically be setup The new airway and junction ID numbers will not interfere with the original numbering scheme of the data file Next are the results of the selected simulation(s) in the following order network balancing, network balancing considering temperatures, transient-state modeling, and altered equilibrium due to fire and distribution of the contaminants. Depending upon the contents of the data file, and the simulation selected, attention, warning, and error message will be shown at locations where calculations resulted in unusual conditions

Jan 1, 1990

By Alton B. Cook

Equipment has been designed and fabricated for study of the vaporization of oil during gas-cycling operations, A sand-packed steel tube, which can be rotated to minimize gravity drainage, is used as a model oil reservoir. A minute windowed cell at the discharge end of the tube through which the liquid-gas interface may be observed, makes possible the separate removal of produced free gas and gas-saturated oil. The operation of the model oil reservoir, and auxiliary equipment, are described by use of a schmatic flow diagram. Details of the specially designed equipment are illustrated by isometric and pictorial drawings, and a description of the experimental procedure is given.

Jan 1, 1959

By M. J. Dailey

This paper is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The property of the Silver King Coalition Mines Co. is situated in the western past of the Park City mining district, Utah, about 1 ½ miles southwest of the town of Park City, The elevation at the collar of the main shaft is 8,137 feet above sea-level.

Jan 1, 1930

By G. E. McElroy

[During the period July, 1923, to April, 1924, we made a large number of careful determinations of the resistance to the passage of air in selected sections of airways in the metal mines of Butte, Mont. The experiments were conducted with the cooperation of the Anaconda Copper Mining Co., Frank D. Cannon, mining engineer of that company, and Fred P. Gaethke, mining engineer of the bureau, assisted in carrying out this work. This paper summarizes the, main group of data obtained in the form of a table, of friction factors, or coefficients of friction that is, values of K in the generally accented formula or air flow of [P = KSV or H = KSV2 ] where, in units customary to mining practice;]

Jan 1, 1925

Improve the dust control effectiveness of dry collection systems on surface coal mine drills. Approach Use a dust pelletizer to convert the respirable dust particles discharged by the dry collector into dust pellets that present no health hazard. Background Blasthole drills are well-known sources of respirable dust that can contain significant amounts of quartz. The drills frequently use a dry cyclone-filter type collector that can obtain dust reductions theoretically greater than 95 pct. However, surface mine drills using dry collectors typically have three major dust sources that significantly reduce the overall effectiveness of the collection system: (1) the dust collector dump cycle, (2) drill shroud leakage, and (3) leakage around the drill stem seal in the drill table.

Jan 1, 1989

Reduce shaft sinking costs and workers exposure to mechanical hazards, drill dust, blast dangers, and fumes. Approach Replace drilling and blasting by using a large, cab-mounted impact breaker suspended from the bottom work deck of the galloway. How It Works The pneumatically actuated impact breaker is positioned by an articulated boom con-trolled from an operators cab. The breaker delivers 2,000 ft-lb blows that fragment the rock at the shaft bottom. Mucking is accomplished by a backhoe bucket on an articulated boom mounted on the cab. See photograph. The mucked material can be removed either by dumping into a previously drilled borehole or by being lifted out in a muck bucket as shown in the drawing. Positioning of the breaker, rotating the cab around its vertical axis, and moving the cab support frame around the perimeter of the shaft are all controlled by one joystick. Separate controls position the mucker boom, which can be swung horizontally through a 180° degree arc towards either side of the cab. Because the cab can be rotated to any position around its vertical axis, and can also be moved in a horizontal circle around the shaft, virtually any position on the bottom of the shaft can be reached by the breaker and mucker.

Jan 1, 1981