Search Documents

Investigate the use and placement of lightweight concrete to improve ground control technology in deep mines where deformation occurs under heavy ground conditions and where there is danger of rock bursts. Approach Investigations of lightweight concrete properties and placement methods were conducted in the laboratory and in the field. Three test sections were completed: a monolithic, portal-type structure with integral walls and arch constructed aboveground; an underground test section constructed in a mine drift using plywood forms; and a test section constructed in a mine drift using an air-supported formwork. In the two underground test sections, the light-weight concrete was placed using a piston pump with concrete discharge line. A cooperating mine also used lightweight concrete, in the density range of 25 lb/ft3, to replace timber blocking in a raise preparation structure (the enlarged area across a vein where chutes and manway access arc placed). Other experiments included the use of precast lightweight concrete blocks in situations where ground support was needed, such as fur mine, ventilation doors, stoppings, and barricades.

Jan 1, 1990

By J. O. Jones

[Willis Mountain in southeastern Buckingham County is one of several kyanite deposits its central Virginia. It is composed principally of kyanite resulting from metamorphism of siliceous sedimentary beds rich in alumina. The mountain, which trends north-south, is 2 miles long and is topped by a narrow ridge with sleep rugged sides rising to an altitude of 1,160 feet and projecting 500 fast shove the surrounding countryside. Bureau Mines engineers examiner Willis Mountain early in 1949, when bonded concentrations of coarsely crystalline kyanite were observed in the kyanite-quartzite on the northern end of the mountain and in loose boulders on the eastern slope. Commencing in late July 1949, the investigations continued on the Long Mountain segment for 11 months, ended in June 1950. A total of 600 samples from 32 diamond-drill holes, aggregating 3,876 feet of drilling, and from 255 feet of sampling in 3 trenches was assayed for kyanite and ferric oxide.]

Jan 1, 1954

By H. Billmayer

This report covers the period from June 17, 1974 to February 20, 1975, and describes the work performed in compliance with the requirements of Contract No. H0346102 and Modification No. 1 thereto. The purpose of the contract was to design protective canopies for an Elkhorn Scoop, a Lee Norse Miner, a Wilcox Miner and a Wilcox Bolter; to construct mockups of the canopies; and to obtain machine operator evaluations of the canopy designs by assessing the mockups while installed on their machines in the mines. The overall program objective was to achieve protective canopy designs for the four machines which would be acceptable to the operators.

Jan 1, 1975

The U.S. Environmental Protection Agency (EPA) and the U.S. Congress are presently considering several approaches aimed at reducing the amount of lead in the environment and society's exposure to lead. One approach is to tax domestic primary lead production or consumption. Objective To assist the Congress and the EPA in their decisionmaking, a study was initiated by the U.S. Bureau of Mines, which assesses the minerals related implications of a tax on U.S. primary lead production and primary lead imports. This investigation analyzes the impacts of a primary lead lax on: (1) domestic primary lead production, (2) domestic lead coproduct and byproduct production (including bismuth, cadmium, germanium, indium, silver, and zinc production), (3) domestic secondary lead production, (4) lead imports, (5) domestic lead recycling activity, and (6) the U.S. lead price. Study Findings Domestic Primary Lead and Primary Lead Coproduct and Byproduct Production. A quantitative analysis based on the application of the Bureau's Supply Availability System (SAM) has been conducted to determine the impacts on domestic primary lead and primary lead coproduct and byproduct production from domestic lead source material for a range of taxes.

Jan 1, 1992

By J. T. Schimmel

The purpose of this investigation was to obtain complete information on some of the uses of a 24-inch-diameter auger in the underground mining of pitching anthracite beds. The auger was placed in operation early in 1958 to drive ventilation connections between coal gangways driven by a continuous miner. Although designed to drill rise holes only, it was used also to drill dip holes. The latter holes were drill id from an adjacent gangway to avoid interference between the auger and the continuous miner. These holes established immediate ventilation returns when intersected by the continuous miner. Bureau participation in the project covered 361 working days. The auger was used on 288 shifts, usually one 7-hour shift per day, and drilled 3,246 feet, of which 493 feet were reamed. The longest hole was 87 feet; hence the maximum drilling depth of the machine (rated at 100 feet) was not required. Holes drilled normal to the strike of the bed ranged from 30 to 66 feet deep, averaging 45 feet. The continuous miner drove gangways on 575 shifts. Thus, the auger worked one shift for each two worked by the continuous miner and was used on less than 80 percent of the workdays. The auger drove 24-inch holes 10 times faster than the larger, conventional openings could have been driven by usual mining methods and exceeded the workload for which it was purchased. Augering eliminates exposure to the hazards encountered in driving chute-work by conventional methods and provides adequate circular ventilation openings, which are strong in self support and are adaptable to reaming when required. With alterations, the auger may have limited use as a production machine in thin-bed pitch mining but cannot compete with established methods of thick-bed pitch mining.

Jan 1, 1962

By J. Schlocker

The present emergency has greatly stimulated interest in the light metals - aluminum and magnesium - owing to their extensive use in airplane construction. The $63,000,000 plant being erected in the Las Vegas Valley by Basic Magnesium, Inc., under the auspices of the Defense Plant Corporation,

Jan 1, 1942

By Eugene Baker, Joseph Cervik, Albert Sainato

In Europe, water infusion is used widely to reduce generation of respirable dust during mining. Its use in the United States is limited to a few plow operations in the Pocahontas No. 3 Coalbed. This Bureau of Mines report describes the technology for infusing water in to a longwall panel and reports the results of a recent demonstration in the Lower Sunnyside Coalbed that achieved dust reductions averaging 58 pct. Because water infusion increases moisture content of the coalbed, face air velocities in excess of 500 ft/min (2.5 m/s) are possible, further diluting dust levels before dust entrainment occurs. An economic analysis shows a 23-pct reduction in operating costs when coal production is increased by changing from unidirectional mining to bidirectional mining with water infusion.

Jan 1, 1983

By Ruth F. Brinkley

This report is the 17th of a series originally issued annually, and more recently bienially, to acquaint the reader with the work of the Division of Explosives Technology, Federal Bureau of Mines. It differs from preceding reports in that its material is presented in two parts: Part I reviews briefly the overall activities of the Division during fiscal years 1955 and 1956;4/ part II presents in abstract form, the publications of the Division during that period. As it is not unusual for research completed in the course of one report period to be published only in the following period, the Bureau believes that the present approach will give a more accurate presentation of its work for the period considered. The Bureau hopes too, that the somewhat more concise presentation will prove convenient to the reader.5/ PART I -RESEARCH AND TECHNOLOGIC ACTIVITIES The activities of the Division during fiscal years 1955 and 1956 reflected the steadily growing preoccupation with factors affecting the safety of permissible explosives and those affecting the tests used for approval of these explosives. Findings by a team of French investigators prompted a study of the influence of atmospheric moisture on the ignition of firedamp by

Jan 1, 1961

By G. R. Friggens

A nuclear method for continuously monitoring the coalbed and ash levels and void formation in commercial-scale, fixed-bed, pressurized gas producers is proposed. Measurement of gamma ray transmission through the coalbed is the basis of the method. The coalbed level is monitored by detecting the trans-mission of gamma rays from a 1 to 2 Ci Co-60 source positioned on the outside wall of the vessel. Coal bridging or, alternatively, ash level is monitored by a 10 Ci Co-60 source at the center of the coalbed. Source activities and geometries are calculated for a 12-foot-ID producer designed to operate at 350 psi. Source capsule and detector specifications and operational safety are also discussed.

Jan 1, 1973

By Dennis A. Long

"The size of off-highway trucks has increased substantially over the last decade, bringing about a radical change in truck maintenance practices and procedures. As a result, surface mine maintenance mechanics today are faced with the increased hazards of working with larger and heavier tools and components and doing repairs at greater heights, thereby exposing them to a high potential for serious injury or death. Not surprisingly, the number of accidents involving truck maintenance mechanics is significantly increasing.The Bureau of Mines has assessed the haulage truck maintenance safety problem, analyzing maintenance-accident data over the 7-yr period, 1978- 84, in terms of personnel, job activities, truck components and systems, tools involved, and truck design. This assessment, based on the review and interpretation of 1,225 haulage truck maintenance accident reports, identified major factors contributing to these accidents. Overall, young, inexperienced workers are involved in most accidents. A typical maintenance accident involves a male mechanic under 33 yr old, with less than 5 yr job experience. INTRODUCTIONOver the past decade, surface mine maintenance and repair operations have changed radically. The number of maintenance personnel has grown along with the hazards of working with larger and heavier components at greater heights and with larger and heavier tools. Furthermore, transfer of skills from over-the-road vehicle mechanics is not as feasible as it once was, because of the ever increasing size of mining equipment and the complexity of its design. In short, surf ace mine equipment maintenance and repair has become increasingly sophisticated as well as labor intensive, necessitating further research and evaluation in terms of both safety and efficiency (1, 7-8) 2"

Jan 1, 1986

By Vernon R. Miller

The Bureau of Mines developed and evaluated a detector-sorting device to separate the copper-bearing portion from the barren portion of native copper ores. Small-scale sorting tests were run on minus 1-inch plus 1/2-inch size materials from the following Michigan samples: Winona, Kingston, and Centennial ores, and "poor" rock from the Champion mine dump. Results showed that 60 to 85 pct of the copper was recovered in 9 to 19 wt-pct of the sorted fraction. About 90 pct of the copper recovered was obtained in the first pass through the sorter. For the Kingston and Centennial ores, combinations of sorter concentrates and fines generated during crushing, resulted in recoveries of 93 and 94 pct, respectively, of the total copper in the samples. The combined products constituted about 66 wt-pct of the total sample and allowed the balance to be discarded with only a 6 to 7 pct copper loss.

Jan 1, 1974

By John P. Coughlin

Software techniques developed by the Bureau of Mines Denver Research Center for real-time microseismic data analysis are presented. These techniques focus on the simple acquisition of P-wave arrival times and their use in event location. The paper discusses in detail software techniques to separate microseismic events from mining noise such as drilling and from very large events such as rock bursts. Incorporation of these techniques has enhanced the reliability and accuracy of computer-based monitoring of microseismic activity in ongoing research by the Bureau.

Jan 1, 1982

By M. M. Fine

In an experimental study by the Bureau of Mines, in cooperation with National Lead Co., the roast-flotation process was found to be an effective means of upgrading certain cobalt-nickel stockpiles. The research was undertaken to determine whether the process could yield an enriched feed, with a minimum cobalt content of 6.0 percent, for the company refinery. The stockpiles (products of the company Fredericktown, Mo., milling operations) were essentially complex sulfides of cobalt, nickel, copper, lead, and iron, 1 sample of which contained 2.84 percent Co and 3.57 percent Ni. After a controlled oxidizing roast at 400° C., laboratory flotation with conventional sulfhydric reagents yielded an enriched concentrate analyzing 9.22 percent Co and 11.43 percent Ni, with recoveries of 84.9 and 85.8 percent, respectively. These are typical laboratory data; other data indicated higher grades were possible but at reduced recoveries. A brief, continuous campaign verified the applicability of the process to the raw material in question but was not continued long enough to establish optimum conditions. As a consequence, the results of the large-scale tests did not equal those obtained in the laboratory but definitely confirm the beneficiation possible from the roast-flotation process.

Jan 1, 1958

"Health standards in the U.S. are among the highest in the world. Achieving these standards have often had an impact on productivity, slowing output, and raising prices to levels that make it difficult to compete with many foreign industries. The answer to many of these problems lies in the development of new and advanced control techniques. This overview has identified some of the major respirable dust technological hurdles that have been overcome, and provided some insight into current and future approaches underway to remove these obstacles and to provide the United States with the most advanced state-of-the-art mining industry in the world from a respirable dust standpoint. The necessary developmental research is costly and time-consuming. The long-term, high-risk aspects of this effort are being addressed by the Bureau and the Generic Center on Respirable Dust, with support by industry. This should be recognized as one of the principal agents through which the great mineral potential of this Nation can be realized, and our international status as a mining power be assured without compromising the health and welfare of those who ensure it.The problem of more stringent dust standards will continue to grow. To date, approximately 40 pct of the coal mining industry has been placed on more stringent dust standards due to quartz. Control techniques must be improved if mandated levels are to be met. As longwall production increases, dust levels will also increase. In light of the industry trend toward longwall mining, if no new control technology is available, the Federal dust standard will act as a constraint on future output per hour. The Bureau has recently completed a survey of 18 coal preparation plants; 50 pct of these operate at dust levels which exceed 2.0 mg/m3; future work will be directed toward solutions in this area. The 2.0 mg standard for respirable dust is for dust particles which are below 10 pm in diameter. Recent studies have shown that dust in the range between 10 and 25 pm can cause obstructive airway disease. The Bureau is currently determining the extent of exposure to dust in this size range from various mining operations."

Nov 1, 1988

By Oliver Bowles

"Introduction.During recent months the Bureau of Mines has conducted a detailed study of the slate industry with special reference to increased efficiency in its production, preparation and utilization. The results of these investigations will be incorporated in a forthcoming bulletin. The purpose of this preliminary paper is three-fold. One object is to bring to the attention of slate producers certain modifications in manufacture and classification which would encourage a wider use of slate. A second purpose is to direct the thought of roofers toward the importance of proper laying of slate, and the third object is to acquaint the general public with its enduring qualities.Origin and character.Without entering into any detailed discussion of the origin and history of slate, a subject to be covered in the bulletin mentioned, it may be of interest to the general reader to know that slate is originally formed from mud or soft clay, carried down by streams and laid down in successive layers in deep water. The pressure of superimposed materials gradually compresses the clay into a firm rock known as shale. In many places this shale was, during the succeeding ages, subjected to intense pressure and folding due to mountain-building forces within the earth. This intense pressure, together with high temperature, changed the clay into other minerals such as mica, chlorite, and silica, which are very resistant to weathering, and also developed a very definite cleavage or splitting direction which characterizes the rock as slate. It is this property which renders slate of value for roofing, for, by using a broad chisel and a wooden mallet, a slate worker can readily split it into thin sheets which are later trimmed into rectangles of various sizes."

Jul 1, 1921

By Bernard Porter

Differential thermal analysis measurements were used to characterize a phase diagram for the KF-YF3 system at compositions between 0 and 60 mole-percent YF3, A congruent melting point compound was observed at 3KF?YFs, which melts at 965°±5° C and undergoes solid-state decomposition at 725°±2° C. One peritectic and two eutectic compositions are also defined.

Jan 1, 1969

By Jacqueline A. McClaskey

The U.S. Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important non fuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The Bureau's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the U.S. Bureau of Mines survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1993

By Gloria L. Walker

The Bureau of Mines Information and Analysis Directorate collects worldwide data on virtually every commercially important nonfuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. This data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), to place the collection of mineral statistics on an annual basis. The most recent authority for the Bureau of Mines Information and Analysis activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress), which strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1990

1. In 2003, 14,391 mining operations reported employment statistics to the Mine Safety and Health Administration (MSHA). Almost half (49%) were sand and gravel mines, followed by stone mines (30%), coal mines (14%), nonmetal mines (5%), and metal mines (2%).

Feb 1, 2005

By John B. Shutack

In an effort to improve the performance of the explosive-anchored rock bolt, the Bureau of Mines studied the effect of the detonation velocity of the explosive and type of charge (linear or nonlinear) on the fracturing tendency of the anchor tube. Also, different types of tubing were compared to determine the one most suitable for use as an anchor tube. The Bruceton up-and-down method was applied in tests in which steel shooting blocks having boreholes ranging from 1-3/8 to 2-1/8 inches in diameter were used. Of the four types of tubing evaluated, a welded A-178 tubing that was drawn over a mandrel and renormalized gave the most promising results. The A-179 seamless tubing that is normally used with the explosive bolt was the most inferior. Both types, however, gave significantly better anchorage than the conventional shell when tested in both laboratory and underground experiments. Within the range of velocities studied (5,000 to 7,000 m/sec), the type of explosive showed no significant effect on anchor-tube performance. In general; linear explosive charges provided better anchorage than nonlinear charges.

Jan 1, 1968