Search Documents

The production of harmful pollutants from coal mines and/or from coal and associated strata has been a recognizable fact in the United States for over two hundred and seventy years. In 1698, Gabriel Thomas observed(l) that the colored water flowing from streams in this country was similar to that which flowed from the coal mines in Wales. Hence, water pollutants such as acid were being produced before any known coal mines were operating in this country. The coal mining industry has contributed to the increase of pollution by exposing large amounts of sulfide materials that enable the reaction of water, oxygen and sulfur containing materials to form acid. A map of the United States coal fields can be seen on Figure 1. The anthracite regions of Pennsylvania, although small when compared to the total reserves, have produced some of the country's major water problems. The map indicates the extent of bituminous reserves of the Appalachian and midwest regions. Also evident are the bituminous, subbituminous and lignite coal reserves in the west which have recently come into greater demand. Acid mine pollution is encountered in numerous states, but the major problem is found in the Ohio, Susquehanna, and Potomac River basins.(2) Most coal beds contain some sulfur which may be in the inorganic, sulfate, or sulfide form, and thus have the potential to produce sulfuric acid. However, much of the strata that overlays the coal beds also contains acid neutralizing materials. Therefore, the amount of acid produced depends upon the amount of both acid and alkali materials that dissolve in the water in any given mine. The common sources of sulfurous material in the seam or surrounding rock are generally called sulfur balls or "nigger heads" by the miners. Sulfur balls that have been observed(3) seem to be equally divided between those containing sulphuritic iron capable of producing sulfuric acid upon oxidation and those that are primarily calcium carbonate. It has been observed in many instances that two types of water, acid and alkaline, are being produced in the same mine. A study of the geological strata and a survey of subsidence, faults and sulfur balls will usually give some indication of why this happens. The reaction of pyrite (FeS2) with oxygen and water to form ferrous sulfate (FeSO4) and sulfuric acid (H2SO4) by a series of complex chemical interactions is well documented but not well understood.(4,5) However, it is well known that the reactions to form the acid cannot occur unless all three constituents are present. Since pyrite is inherent in most coal seams and air is needed to sustain the miner, the most logical answer is to eliminate water infiltration into the mine, or to remove it from the mine before acids can form.

Jan 1, 1970

By S. P. Kinney, P. H. Royster, T. L. Joseph

An investigation of the production of iron in the blast furnace is obviously not an easy subject for research . Enough is known of the mechanical , thermal and chemical conditions existing inside the furnace to say certainly that they are complicated. Furnace operators have found that the process is sensitive to a number of known and to many unknown operating conditions . In order to form any conclusions of value , it seems necessary to collect a large amount of data taken with considerable care and accuracy. These facts make a blast furnace research difficult but not impossible . The most serious obstacle in attacking the problem comes from the fact that it is useless in the design and operation of the blast furnace to use the method of " trial and error , which has proved valuable in so many other industrial problems . The variables are so interrelated and are so dependent one on the other that the number of experimental combinations to be tried is enormous . There are certainly not less than twenty factors in furnace operation and design that are known to influence the results . This is apparent if it is remembered that a phrase like " size and shape of the furnace" includes height of the furnace , height , diameter and angle of the bosh , inwall batter , stockline diameter , and furnace volume ; and that a phrase like " chemical and physical properties of the fuels charged " includes size and shape of the lumps , density, porosity and strength of the coke , in addition to its chemical analysis . Let us suppose that we need choose for each of twenty factors one of two values , for example , suppose we must say only that the furnace shall be " tall " or " short , " that the bosh angle shall be " flat " OF "steep , that the ore shall be " coarse " or " fine , " or that the blast has to be "hot" or " cold , " the number of resulting combinations is more than one million . In putting twenty pennies on the table , either heads up or tails up, the number of permutations possible is the twentieth power of two , slightly more than one million. It is obvious , therefore , that some sort of mathematical relationship , a set of rules of thumb , laws , curves or the like , are needed . Whether the relationships , curves or formulas are derived from experiment , from theory, or from mere guess -work, makes no difference provided they agree with the known facts . If they do not agree with known facts , they are worthless no matter what their origin or how weighty the " authority" vouching for them. Few such relationships have appeared in blast- furnace literature , and it may be doubted whether such formulas can be discovered .

Sep 1, 1923

By R. V. Ramani, K. Bode

"IntroductionThe theory of particle dispersion and deposition in turbulent flow is important to many fields of science and engineering. Dispersion has been studied in some detail since the early fifties (Taylor, 1954; Fischer, 1967; Osipov and Grekov, 1968; Skobunov, 1970 and 1973; Klebanov and Martynyuk, 1974). A broad research effort has also been underway in studying the mechanics of dry particle deposition. Friedlander and Johnstone (1957) proposed a theory, according to which particle deposition from vertical pipe flow could be described by an eddy diffusion transport followed by a final flight to the surface. There have been numerous revisions and additions to this original theory (Owen, 1960; Liu and Agarwal, 1974; Liu and llori, 1974; El-Shobokshy and Ismael, 1980) The mining process essentially consists of breaking in situ materials and transporting them out of the mine. An inherent characteristic of this process is the generation of fine particles. Fine airborne particulates are associated with a number of threats to the health of the miners; fine coal dust can also result in mine-wide catastrophic incidents such as dust explosions. For these and other reasons, it is important to understand the behaviour of airborne dust particulates, particularly their generation, entrainment, transport, dispersion, and deposition in the mine environment for their control.Mine related studies on dispersion and deposition have been few. Yet, several studies of gas and dust dispersion, diesel exhaust contamination, and methane ingress into mine workings have recognized the need for developing reliable parameter values for fundamental understanding of the phenomena (Da""Yes and Slack, 1954; Hodkinson, 1957; Hodkinson and leach, 1958; Mass and Wildschut, 1966; Airey, 1969; Courtney et al., 1986; Stefanko, Ramani, and Thakur, 1974; Stefanko, Ramani and Kenzy, 1977; Bhaskar, 1987, Bhaskar and Ramani 1990; Qin and Ramani, 1989; Shankar and Ramani, 1990)."

Dec 1, 1995

By H. Kenworthy

The investigations described in this report were undertaken to demonstrate, on a laboratory scale, the possibility of recovering several million pounds of tin plus tungsten contained in stockpiled and currently rejected slags from the Longhorn tin smelter at Texas City, Tex. At the same time, it was anticipated that the treatment procedures developed might be applicable to slags from other tin-smelting operations. Results of the laboratory work show that it is possible, by pyrometallurgical means, to separate the tin and tungsten into products of intermediate grade that may be returned to the smelter circuits for further upgrading. Several methods of treatment were investigated. The methods that proved effective were: Fusion reduction, chloride volatilization, sulfide volatilization, and carbide formation. Over 90 percent of the tin and tungsten could be removed from the slat by any of these methods. Each type of treatment has advantages and disadvantages, and it could not be determined from the small-scale work which method was the more meritorious. Tungsten and (in some types of treatment) tin-bearing products were diluted by iron, the separation of which will require additional studies. Prevention of a portion of the iron from reporting with the tin or tungsten is a distinct advantage and possibility that will require inure laboratory work to develop the needed techniques for its accomplishment. Tin products from single treatments of stag ranged up to 75 percent in tin content but were more generally under 35 percent. Tungsten products were usually under 15 percent; but segregated portions could be selected, at a sacrifice in recovery, that contained up to 50 percent tungstic oxide equivalent.

Jan 1, 1957

By James J. Hanslovan

Stresses that damage coal mine trailing cables were investigated to obtain a quantified description of cable-stress locations, magnitudes, and frequency of occurrence. Stresses occurring in operating mining sections were measured and observed. Answers to questions that arose during the underground investigations were pursued under controlled conditions, both in the field and in the laboratory. Cable-handling suggestions that minimize or eliminate the stresses are summarized in the form of recommendations to mine operators.

Jan 1, 1979

By John J. Henn

Two lime sinter processes for recovering alumina from clay, the double-leach process and the single-leach process, are evaluated in this Bureau of Mines report. In both processes, clay and limestone are mixed and sintered to form calcium aluminate from which alumina is extracted as sodium aluminate by leaching with a dilute solution of sodium carbonate. The pregnant liquor is desilicated, then carbonated to precipitate alumina trihydrate which is recovered and calcined to a,-alumina. The fixed capital costs for plants producing 1,000 tons per day of alumina are $85 million for the double-leach process and $86 million for the single-leach process based on a Marshall and Stevens chemical equipment index of 240.0. Because plant locations are variable with respect to the proximity of clay and limestone deposits, a nomograph is included to determine operating costs at various delivered costs of clay and limestone. For plants at which the delivered cost of clay containing 30 percent A1203 is $2 per ton and the delivered cost of limestone is $1 per ton, the operating costs are $81.04 and $89.87 per ton of alumina for the double-leach process and single-leach pro-cess, respectively.

Jan 1, 1969

By Michael J. Friedel

As part of an investigation aimed at improving the health and safety and competitiveness of the mining industry, the U.S. Bureau of Mines evaluated the application of common offset radar profiling, using a 250-MHz ground-penetrating radar (GPR) system, for the detection of fractures in igneous rock. A series of radar reflection surveys were conducted to detect and delineate the extent of fracturing at various granodiorite and gabbro quarries and outcrops located in Minnesota. The application of radar profiling for detecting joints, sheeting fractures, shear zones, and depth to water table was demonstrated to be feasible with minimal processing. Radar reflection interpretations were verified by visual inspection of the rock mass and field mapping of local structure. The radar reflection section provides a simple, rapid, and cost-effective means for mapping of shallow (less than 10 m) small-scale fractures (greater than 0.25 cm) in igneous rock masses (characteristic of velocities between 0.061 m/ns for gabbro and 0.125 m/ns for granodiorite). Depth or distance estimates to fractures are within 10 pct of the actual, and time-shift compensation is necessary only when topographic irregularities exceed 30 cm.

Jan 1, 2010

By L. E. Geyer

"The following list gives the title and author of various publications of the Ceramic Experiment Station, Columbus. Ohio, of the Bureau of mines, together with other ceramic publications of the bureau, which have been published in technical journals and by cooperating agencies. The list also includes the publications on ceramics which have been issued as bulletins, technical papers, or mimeograph Report of Investigations of the bureau.Papers Published in the Technical Press.The Effect of some Electrolytes on the Properties of Clays. Schurecht, H.G. Jour. Am. Cer. Soc., Vol. 1, #3, March, 1918.A Pycnometer Operated as a Volumeter. Schurecht, H.G. Jour. Am. Cer. Soc.,Vol. 1, #8, August, 1918.The Properties of some Ohio and Pennsylvania Stoneware Clays. Schurecht,H.G. Jour. Am. Cer. Soc., Vol. 1, #4, April, 1918.The Fusibility of Graphite Ash and its Influence on the Refractoriness of Bond Clay. Booze, M.C. Jour. Am. Cer. Soc., Vol. 2, #1. Jan., 1919.Behavior under Brass Foundry practice of Crucibles containing Ceylon, Canadian and Alabama Graphites. Stull, R.T. Jour. Am. Cer. Soc., Vol. 2, #3. March, 1919."

Oct 1, 1924

By D. Harrington

"While distribution of air currents to working faces is a necessity in coal mines, especially those having explosive gas, advancing faces in metal mines rarely have circulating air other than the ordinarily inadequate amount supplied through the compressed air system. Even where comparatively large quantities of air pass through main mine shafts and levels. whether the circulation is actuated by fans or by natural ventilation, only occasionally can a metal mine be found where any considerable percentage of the ""blind ends"" has circulating air of sufficient velocity to be measured by an anemometer or even be discerned by deflection of flame of candle, or of acetylene lamp; and unfortunately these ""blind ends"" include nearly all of the places from which rock is taken.During several years study of metal-mine ventilation in various mining districts of the United States, it has been found that in some mines many of the workers in ""blind ends"" practically continually breathe air with 0.02 to 0.04 per cent of CO gas from unremoved fumes from explosives; in other mines CO2 chiefly from timber decay and breathing of men, is so high that a candle will not burn though usually the acetylene lamp will, hence oxygen is below 17 per cent but above 12 per cent; in some regions CO2 from strata fills the entire mine forcing cessation of work; in other mines in dead ends, gases such as nitrogen, H2S, SO2, etc., are found under some conditions. In many regions with hot rock or water (especially in deep workings) men in blind ends must work with little or no circulation, in air above SO degrees F. and even above 90 degrees, relative humidity only too frequently being around 100 per cent; in other regions workers in blind ends in practically ""dead"" air must continually breathe enormous quantities of finely divided rock dusts. All of the above conditions are decidedly harmful to health and prevent the worker from delivering anything approaching an adequate quantity of work, and in addition, some of these conditions have direct or indirect effect in bringing about definite increase of accidents; all of the above mentioned bad conditions in ""blind ends"" in metal mines as well as their ill effects, are remediable by providing at those places adequate quantities of fresh circulating air."

Nov 1, 1923

By R. D. Currie

"INTRODUCTION Compressed air for operating coal-mining equipment is seldom considered in conjunction with modern methods and appliances. But the Jamison Coal & Coke Co. has proved the economy and efficacy of compressed air for this purpose at its Mine 8 near Farmington, 8 miles west of Fairmont, Marion County, W.. Va., and the mining industry as a whole concedes its superior safety in gassy or dusty coal mines.The uses for compressed air in coal mining are now generally associated with such equipment as coal punchers, chain-breast machines, and to a lesser extent the ""radialaxe"" type of mining machines.Electricity has rapidly superseded compressed air for power in coal mines during the past 20 years; and in the last few years the general, and often unwise, use of electricity at the face region has taken on added impetus through the widespread use of mechanical loading equipment.Some of the unfavorable results of this increased use of electricity are shown in the growing number of mine explosions and fires of electrical origin. In the past four years 59 explosions of this type took the lives of 672 men, or 74.8 per cent of the total number of deaths from explosions were due to explosions of electrical origin.3In 1926, an explosion in Mine 8 of the Jamison Co. killed 19 men. The exact source of ignition was not determined, although it was definitely decided that it was of electrical origin and probably was at an electric coal-cutting machine.Prior to this disaster the company had done some experimenting with compressed-air-driven mining machines, and its Mine 9 had been completely equipped with air-driven chain-breast machines; a few of these machines were also in use in Mine 8. The explosion, however, gave impetus to the adoption by this company of compressed air for operating face equipment. The chain-breast machines were as satisfactory as electric machines of the same type; but the trend in the industry was toward faster cutting machines, which required less physical exertion on the part of the operating crews. A track-mounted machine of the arcwall type was found to be suitable for the conditions and system of mining, so that one of these operated by compressed air was developed by the Jeffrey Manufacturing Co. working with the officials of the Jamison Co.The first of these machines was installed in the latter part of 1926 and additional machines were delivered from time to time, until at present there are nine of them in the mine. Necessary improvements have been made, with the result that a fast-cutting, easily handled, efficient, and safe mining machine has been developed for cutting the hard Pitts¬burgh bed coal of the Fairmont field."

Oct 1, 1932

By W. E. Wallace, C. A. Hill, M. J. Keane

"Diesel exhaust particulate material from exhaust pipe scrapings of two trucks, diluted automobile diesel exhaust particulate material collected on filters, and two oil shale ores were prepared for the Ames mutagenrcity assay by dichloromethane OOP ex¬traction, by dispersion into 0.85% saline, or by dispersion into dipalmitoyl lecithin (DPL) emulsion in saline. Salmonella typhimunum TA98 was used to detect frameshift mutagens in the samples. Samples of diesel soot gave positive mutagenic responses with both DCM extraction and DPL dispersion, with the DPL dispersion giving higher results in some cases. The results suggest that possible mutagens associated with inhaled particles may be dispersed or solubilized into the phospholipid component of pulmonary surfactant and become active in such a phase.INTRODUCTIONThe Ames Salmonella/microsome assay (Ames et al., 1975) has been shown to be a useful test for detecting genotoxic properties of various agents. Hundreds of specific chemicals have been screened (McCann et al., 1975), and the test has been applied for many types of environmental samples. Airborne mutagenic agents, for example, have been found in urban air (Chrisp and Fisher, 1980; Hughes et al., 1980; Ro· senkranz et al., 1978), in diesel engine exhausts (Huisingh et al., 1978), and in the by-products of coal combustion processes (Chrisp et al., 1978).Samples of airborne particles are typically collected on membrane filters, and undergo a rigorous extraction procedure with organic solvents and/or ultrasonic agitation (Clark and Hobbs, 1980). Often extracts are transferred to another solvent that is compatible with the assay system. These extraction procedures, while efficient from an analytical perspective, are not physiologically plausible. The questions that present themselves are whether a demonstrated mutagen can be taken up in vivo and whether the process is quantitatively or qualitatively different from the above laboratory procedure (Wallace et al., 1984).When a particle of respirable size is inhaled to the alveolar region of the lung, its first physiological contact is with pulmonary surfactant that lines the inner surfaces of the alveoli. This surfactant is an aqueous fluid containing proteins, phospholipids, and other components (R. J. King, 1982). The principal phospholipid constituent is L·alpha-phosphatidylcholine, beta,gamma-dipalmitoyl, or dipalmitoyl lecithin (OPL) (l. C. King et al., 1981)."

Jan 1, 1989

By David M. Hyman

The Bureau of Mines has developed two experimental designs for deter- mining the volumes and relative proportions of the various gas species, particularly methane (CH4), occluded in rock salt. To date, the rock salt samples analyzed have been relatively small (400- to 1,000-gram) grab samples from Louisiana Gulf Coast domal salt mines. The results obtained are comparable to results in Polish domal salt mines, in terms of occluded gas volumes per mass of rock salt. The notable difference between the Louisiana and Polish occluded gas mixtures is in the relative proportions of the individual gas species. The two methods used by the Bureau are ballmill crushing and dissolution. Of the two, the dissolution method appears to be more versatile because it can be performed in situ. The relevance and applicability of data on the occluded gas contents of rock salt are dependent on sample size, sample collection method, geologic context of the sample, and the correlation with gas emissions that occur as a result of mining-induced fractures and pressure differentials.

Jan 1, 1982

By C. J. Tsai, K. Olson, R. Caldow, B. Cantrell, D. Y. H. Pui

"The amount of new surface generated during fracture of coal and rock has been found to be directly proportional to the amount of energy associated with the fracture. To confirm this and study the relationship between the new surface and dust aerosol formed during fracture the U.S. Bureau of Mines has conducted experiments simulating fracture as it occurs during mining operations. In addition to fracture energy measurements, fragment size distributions were determined over a size range of 0.5 microns to 1 inch. The size measurements accounted for the mass of the original sample. Material studied was Illinois No. 6 coal, coal from the Taggart seam of Virginia, and Berea Sandstone. The experiment employed a chamber to confine sample fracture fragments and a combination of particle measuring systems. Measurement methods included aerodynamic sizing of entrained dust aerosol with optical counting and inertial impaction techniques, physical sizing of non-airborne fragments by sieving, and optical sizing of fragments using optical counting and scanning electron microscopy.Results of the size distribution measurements indicate that a single size distribution law does not adequately describe the entire fragment size distribution. A combination of two size distribution laws, such as the Rosin-Rammler and log-normal distributions, is necessary to describe this size distribution. New surface created by fracture is primarily found 1n particulate between 2 and 50 microns with a mean size of 12 microns. It was also found that the specific energy of fracture can be linearly related to the .concentration of aerosol in this size range.Only a .small fraction, between 0.02 and 0.16 pct, of the dust particles .generated during fracture become airborne. The remainder adhere to the new surface created during fracture. An entrainment fraction, defined for a given particle size is the ratio of the mass of airborne particles to that of the total particles generated in that size range. This experimental entrainment fraction is related to the Van der Waals adhesion force and the electrostatic forces operating during fracture and is used to derive empirical parameters to model these two processes."

Jan 1, 1989

By J. S. Browning

The physical properties and specific gravity ranges of various liquids and salt solutions used for laboratory sink-float separations of rocks or minerals are presented. The test equipment and techniques employed by the Bureau of Mines in making sink-and-float separations of particles as coarse as 3 inches to as fine as 400 mesh are described. Also discussed are methods of recovering and reclaiming the liquids or salts from the minerals and wash solutions, as well as the hazards encountered and precautions to be followed while working with the materials. The laboratory use of various liquids for separating minerals of different specific gravities has been recognized for many years. During this time, laboratory sink-float procedures have proven their utility as a rapid and moderately accurate means for determining the mineral content of ores, test products, and plant products in certain nonmetallic concentrating operations, such as those producing mica, spodumene, kyanite, and so forth. These procedures also have been used as analytical tools for determining the mineral content and associations of other metallic and nonmetallic ores.

Jan 1, 1961

By C. W. Owings

Recent recommendations of the Bureau of Mines regarding, rock dusting to prevent dust explosions in coal mines have been issued as Mine Safety Board Decision 32 and printed as Information Circular 7109.5/ The last paragraph on page 2 of I. C. 7109 states: After a mine or any part of a mine has been rock-dusted, samples of dust for analysis should be taken from the floor, ribs, roof, and timbers at such intervals of time as will give apple warning of need far redusting in order to maintain the required minimum percentage of incombustible in the mine dust. Details of the methods of sampling and analysis are given in Bureau of Mines Information Circular 7113.

Jan 1, 1940

By P. J. Dallimore

The Bureau of Mines has calculated general time-dependent solutions for radon diffusion from cylindrical and slab rock samples containing uniform radium distribution. Results have been obtained for several sets of boundary conditions. The method is suitable for determining the effective diffusion coefficient and the effective porosity for radon.

Jan 1, 1983

By C. Melvin Lepper

To provide the U.S. mining and energy industries with information in the selection of seismic detectors for high-resolution applications, the Bureau of Mines evaluated 35 velocity detectors (geophones) and 9 accelerometers. It was found that velocity detectors with natural frequencies from 10 to 100 Hz were effective for seismic studies in the 5-to 600-Hz spectrum and that accelerometers were most effective in the 100-to 1,000-Hz range. Although the accelerometers described in this report performed about equally with the better velocity detectors tested, the accelerometers showed higher output voltage levels at higher frequencies, which is an advantage. It is important that a seismic detector and its intended purpose be matched properly to achieve the intended results in high-resolution applications. There are many factors that could affect proper matching, thus careful selection of the best detector for a particular application must be exercised.

Jan 1, 1981

By A. R. Taylor

Low-temperature heat capacities of cesium chloride (7° - 300° K) and cesium iodide (13° - 300°K) were measured with an adiabatic calorimeter. The heat-capacity measurements were analyzed graphically to determine smooth values of heat capacity, entropy, enthalpy function, and free-energy function at 10° K intervals and at 273.15° and 298.15° K.

Jan 1, 1963

By C. L. Brown

The frequency of mine fires during recent years, with an apparent increase in recent months, has focused attention on the necessity of reducing this hazard by every means possible. Investigation reports are available on 51 mine fires of electrical origin between August 15, 1949, and August 16, 1954. Nine other fires in the same period were suspected as being of electrical origin. Every mine fire is a potential hazard to underground workmen; it is remarkable that only six lives were lost as a result of these fires, since the injury list was very high. Modern mining methods, with increased power demands and extended distribution systems underground, involve greater electrical hazards and possibilities of costly production delays as a result of inadequate electrical service. Improvements in electric-power-distribution facilities in many underground coal mines is desirable. The purpose of this paper is to show the need for this improvement as revealed by studies and investigations of electric-power-distribution systems representative of those in a large number of coal mines.

Jan 1, 1955

To develop a system which will effectively detect and extinguish fires in underground fueling areas while also providing a warning for nearby miners. Approach A system involving optical fire sensors. automatically-released dry chemical and aqueous film-forming fluid (AFFF) fire suppressants, and automatic alarms was designed from off-the-shelf, state-of-the-art components, and was in-mine tested at two mines in the two typical underground fueling area situations: fuel transfer areas and fuel storage areas. How It Works As mines become more mechanized, the number of fire hazards increases since fueling areas are more abundant. Fire hazards are especially serious in deep mines, since escape time is longer. To help solve this growing problem, the Bureau of Mines, in cooperation with the Mine Safety and Health Administration (MSHA) and the National Fire Protection Association (NFPA), has developed and in-mine tested a cost-effective fueling area fire protection system. The system was designed to be rugged enough for reliable, long-term use, yet to utilize state-of-the-art, off-the-shelf components to maintain cost-effectiveness. The system consists of cross-zoned, ultraviolet flame sensors used for quick response to fire, and a dual-agent fire suppression subsystem. A dry chemical is used for fast fire -knockdown," and AFFF (or "light water") is used for long-term, fire-securing capability. The basic components of the system are shown in the schematic illustration.

Jan 1, 1982