Search Documents

By K. K. Kelley

This report contains heat-content values for hexagonal crystalline germanium dioxide between 298.15° and 1,350° K., and for germanium dioxide glass between 298.15° and 1,800° K. experimentally determined by the Federal Bureau of Mines. No similar data for these substances are to be found in the literature. The heat-content and corresponding entropy-increment data are presented both in tabular form and by equations. Free energy of formation values are estimated for germanium dioxide glass at 298.15° and 1,800° K.

Jan 1, 1961

By Joseph Cervik

This Bureau of Mines report deals with water infusion of coalbeds, which can control methane emission at face areas during developmental mining and which may sometimes suppress dust. Studies show that water infused into the coalbed flows through the fracture system and displaces the methane in the fractures and prevents migration from the solid coal. Displaced gas migrates away from the face area that has been water infused and enters the return ventilation airways. A gradual decrease in methane emission is observed from the start of infusion until the infused zone is mined through. Depending on the permeability of the coalbed, infusion pressures ranged from 300 to 2,200 lb/in2. Face emissions in the Upper Kittanning coalbed were reduced by 89 pet; reductions of 38 to 79 pet were measured in the Pittsburgh coalbed depending on the relationship between the face cleat direction and mining direction. Respirable dust levels were reduced by about 75 pct on a longwall section in the Pocahontas No.3 coalbed and by about 50 pct on a development section in the Upper Kittanning coalbed, but no statistically reliable reduction was found in the respirable dust levels in the Pittsburgh coalbed.

Jan 1, 1977

By David E. Siskind

The Bureau of Mines studied environmental blast effects in six occupied residential structures. Airblast, ground, and structure vibrations were measured both inside and outside residences for seven quarry production blasts. Walls and floors responded to the blast noise and vibration by shaking at their own natural frequencies, often with greater peak particle velocities than the ground outside the structures or their foundations. The vibrations of the houses generated noticeable internal noise, correlating with the arrival of the groundborne energy. The later arriving airblast wave was predominantly at low infrasonic frequencies (1.0 to 1.5 Hz) and had similar amplitude and frequency characteristics both inside and out-side the structures. Significant structural motions resulted from the air-blast overpressures for at least two of the seven blasts. The most severe airblast effect occurred at a house 1,800 feet from a 5,047-pound (200-lb/ delay) blast. This stucture was subjected to a peak 0.16-in/sec particle velocity and 130 dB(L) airblast. The wall of the second floor responded to the ground vibration and airblast by shaking at particle velocities of 0.15 and 0.28 in/sec, respectively. Analysis of these data and those from additional field studies will be used to identify appropriate, safe, and reasonable impulsive noise levels, measurement techniques, and factors of design applicable to minimizing the adverse environmental effects of blasting.

Jan 1, 1976

By Herbert L. Lines

This paper is one of a series on mining and milling methods and costs published by the Bureau of Mines. The Ash Peak mine of the Veta Mines, Inc., Duncan, Ariz., is of particular interest in that the only metal of commercial value in the ore is silver. The silver is concentrated by flotation; the concentrate is shipped to a smelter for treatment.

Jan 1, 1940

By A. Wahab Khair, Nagendra P. Reddy

"This paper presents an analysis of preliminary tests on the effect of in-situ and operating parameters on fragmentation of coal using a specially designed unique automated rotary coal cutting simulator (ARCCS). In these tests coal blocks with an approximate dimension of 18 in. x 15 in. x 6 in. (45.7 cm x 38.l cm x 15.2 cm) were first. subjected to confining pressures, equivalent to in-situ conditions. Such. blocks were then cut by the cutting head of the ARCCS, thus simulating the action of the continuous miner in underground coal mining. During the tests under a particular set of in-situ and operating parameters a number of other parameters such as 1) penetration of bit into coal, 2) penetration resistance (thrust and cutting pressures), 3) rotating velocity of cutting head, and 4) acoustic emission activity in the coal block were monitored. After each cutting cycle the fractured surfaces were photographed and a velocity survey was conducted by using a sonic technique. At the end of each experiment the cutting paths of the bits in coal were photographed using an optical microscope with a camera attached to it. Furthermore, the coal fragments were collected in bags using a vacuum cleaner. These fragments were then sieved for size distribution analysis. The results of the preliminary tests indicated that underground coal cutting can be simulated in the laboratory and the effects of the important parameters, i.e. operating and in-situ parameters, can be studied successfully. INTRODUCTIONThe continuous-mining machines which were introduced in the 1950's now account for more than half the production of coal from underground mines. Unfortunately, these continuous miners, which were designed for increased productivity, have also increased the concentration of respirable dust in mines. As a result, the Federal Coal Mine Health and Safety Act of 1969 was enacted to enforce on the coal operators that the airborne respirable dust not exceed 2 mg/m3, and was intended to reduce the incidence of coal workers pneumoconiosis. This plus the other aspects of the legislation and the subsequent monitoring and enforcement by MSHA made it very imperative that the coal operators provide a relatively healthier and safer working environment for the coal miners. Since 1970, the Federal government has paid over 11.7 billion dollars to more than 470,000 miners with coal workers pneumoconiosis and their survivors (1). These regulations, coupled with the assessment of the continuing burden on miners, the mining industry and taxpayers appear to have provided an impetus for the mining .community towards comprehending the different parameters that influence dust generation and entrainment."

Jun 1, 1988

By H .. B. HUMPHREY, F. E. Cash

Sixty-one fatal accidents were reported in the mines of Alabama during 1930. This number is a decrease of 15 per cent as compared with 1929; however, production was 13 per cent and the man-hours worked were 16 per cent less than in the previous year. There were 21,731 men employed inside and 3,386 outside. Table 1 gives the comparative rates per million tons and per million man-hours for the United States and for Alabama for 1929 and 1930. These rates are based on figures published by the State and by the United States Bureau of Mines, with preliminary figures for 1930. (These sources of data are used throughout this paper.)

Oct 1, 1931

By T. Estelle Gardner, A. R. Taylor

Heat capacity measurements were made on sodium bromide ( NaBr ) and sodium iodide ( NaI) in the temperature ranges of 7 ° to 300 ° K and 56 ° to 300 ° K using an adiabatic calorimeter . Smooth values of heat capacity, entropy , enthalpy function , and free- energy function were calculated from the heat capacity data at 10° K intervals and at 273.15° and 298.15° K. Entropy and free energy of formation values at 298.15° K also were calculated for the two compounds using entropy values determined in this study and other data reported in the literature . The entropy values calculated at 298.15 ° K were 20.75 ± 0.06 entropy units (eu ) for sodium bromide and 23.55 ± 0.07 eu for sodium iodide .

Jan 1, 1964

By R. G. Gürtunca

The future of the United States (US) mining industry will be affected greatly by recent coal mining disasters. These have resulted in new legislation which will have an impact on mining economic costs as well safety and health of miners. This paper discusses the changes that new legislation and regulations are making to the industry and current research that is producing technologies to make mining safer and will likely impact the future of mining.

Jan 1, 2009

By J. M. Mutmansky, S. Padmanabhan

"The subject of quartz occurrences in respirable coal mine dusts has been of increasing concern in recent years. The primary impetus for this concern has been provided by better measurement technology that has detected an increased number of mines with high quartz content in their respirable dusts. This paper presents the results of statistical analyses of quartz levels in multi-stage impactor samples from eighteen different coal mining sections located in Pennsylvania, West Virginia, Ohio, Illinois, Kentucky, Colorado and Ucah. The quartz and kaolinite determinations were then determined by combining impactor stage loadings to provide larger dust masses and applying the infrared spectrometry procedure outlined in Bureau of Mines/MSHA Method P7.The results will be presented using two categories of data collected during two separate phases of the research:(l) quartz concentration data from mines where quartz was known to be present in relatively high concentrations, and(2) quartz concentration data from mines chosen at random.The aspects of the occurrence of quartz in coal mine airborne dusts that will be reported include the size dependence of the quartz content, quartz variations with location in the mining section, and variations due to mining region. The results of the study show a strong pattern of size dependence of the quartz content in mines for which high quartz concentrations exist. A similar, though less pronounced, pattern exists in mines chosen at random. Quartz levels appear to have a varying relationship to section location and strong geographical patterns do not appear to exist in the data collected. Kaolinite content was found to be similar to that of quartz with patterns that are somewhat more consistent."

Jan 1, 1989

By M. W. Pullen

It is recognized that the determination of electrical resistivity of the earth within a given area may furnish information concerning the location of certain mineralized strata of economic importance. Present knowledge of the electrical resistivity of the various rock formations is almost nil, and the geophysicist who is detailed to make a survey of an area without any data as to the relative resistivity of the underlying rocks is greatly handicapped. Such surveys are usually made within areas known to contain mineral deposits to aid in locating desirable points for drilling. Usually these areas have been prospected by diamond drilling, and drill cores of the various rocks and ores are usually obtainable. Were it possible to make resistivity tests in a laboratory of the drill cores or from pieces of the rocks and ore within an area before attempting a field survey, this would indicate not only the advisability for such a survey but would aid considerably in the interpretation of the results of such a survey. To be of most value a definite method should be used for all such tests, and as yet such a method has not been established.

Jan 1, 1929

By L. Kaufman

Fifteen boride composites were synthesized by hot pressing and evaluated by physical and incendivity testing as non-sparking tool materials. The incendivity tests, conducted at the U. S. Bureau of Mines, Albany Research Center, compared the boride compo-sites with standard cobalt-bonded tungsten carbide material used for coal cutter bits. Two titanium diboride composites and two zirconium diboride composites out-performed cobalt-bonded tungsten carbide in wear resistance and reduced tendency to cause ignitions. However, three of these candidates exhibited undesirable chipping. The remaining candidate, a TiB2-(Ni, Cu) composite, did not chip, nor did it cause ignitions at levels where cobalt-bonded tungsten carbide tools caused ignitions in the incendivity tests. Thus, this material appears to be a logical candidate for further development.

Jan 1, 1973

By S. J. Page, P. Bolsaitls, W. E. Wallace, C. A. Hill, M. J. Keane

"Boiling respirable quartz dust in water for 10 to 40 minutes decreases the cytotoxicity for both erythrocyte hemolytic potential and pulmonary macrophage release of lactate dehydrogenase in vitro. The potential is reduced to near zero in the boiling concentration range of 1 to 10 mg quartz per ml water in boiling times of 20 to 40 minutes. Below this range the detoxification occurs over a longer boiling time. Above this range the hemolytic potential remaining after 40 minutes of boiling approaches native quartz potential with increasing concentration up to 30 mg quartz per ml water. Replacing the media with fresh at the midpoint of boiling results in full detoxification through 20 mg per ml. Pre—boiling the medium with quartz or silica gel reduces the effect of subsequently boiling test samples. Detoxification persists after mild drying at 110 C for 8 hours, and persists after three days of resuspension in water at room temperature. Additional data on persistence of the effect, on the use of acidic and basic media treatment, and on surface analyses are presented, with a discussion of a working hypothesis and research needs.IntroductionResearch underway to determine interactions of quarts and other mineral dust surfaces with pulmonary fluids and alveolar macrophages in culture led to the observation that when dusts were autoclaved in aqueous suspension, their cytotoxic effects on macrophages wore suppressed, in some cases fully and even after several days incubation with the cells. This finding was in direct contradiction to earlier results from both short term macrophage lysosaal enzyme release assays, as well as longer term cytotoxicity assays from macrophages in culture; in those studies, dusts were steam autoclaved at 121 121 ºC with no liquid water but with steam present. (1,2) However detoxification under boiling conditions has been reported in other research.(3). It was decided to use the hemolysis assay to further investigate these findings, because of its sensitivity, simplicity and cost."

Jan 1, 1988

By Potter G. M.

Ore-dressing tests were conducted on a sample of ore submitted by the Richmond Hill Mining Co. of Lead, S. Dak. as a part of the Bureau of Mines program for investigating potential domestic sources of manganese. Half of the sample was taken from the 300-foot level and half from surface cuts. The problems involved were liberation and rejection of silica and iron and removal of lead, Silver, and gold from the manganese concentrates. Although a portion of the silica and iron oxides was too intimately associated with manganese minerals for rejection by ore-dressing methods, thus limiting recovery of high-grade concentrates, the Richmond Hill ore was found amenable to simple gravity methods of concentration for producing intermediate-grade products. By jigging and tabling, 73.8 percent of the total manganese was recovered in a product that, when sintered, assayed plus 40 percent Mn. Lead, silver, and gold were successfully removed from gravity concentrates by a chloridizing roasting treatment.

Jan 1, 1948

By John B. Bennett

This Bureau of Mines report presents a method of standardizing forecasts of mineral consumption that attempts to resolve the problems caused by the use of different data bases, different definitions of minerals consumption, and different base years for making projections. Using this method, forecasts of U.S. and world mineral consumption, in the year 2000, for nine commodities (aluminum, chromium, cobalt, copper, manganese, nickel, tin, tungsten, and zinc) are standardized and compared. Also selected forecasts or associated growth rates are used to generate implied values of consumption for 1980-83, which are then compared to actual values of consumption for 1980-83. The economic growth predictions underlying the forecasts are examined, and some general conclusions are drawn. A description of each methodology used to generate these forecasts is given in an appendix.

Jan 1, 1986

By J. J. Drost

The feasibility of basic oxygen furnace (BOF) offgas heat recuperation by preheating scrap was investigated on a pilot plant scale by the Bureau of Mines. In this study, offgases generated during the oxygen blowing of a molten pig iron and scrap charge were passed through a static bed of shredded auto scrap. Scrap quantities varying from 100 to 180 pounds and representing from 22 to 40 percent of the 450-pound BOF metallic charge were preheated in this manner. Average scrap bed temperatures of 1,650° F for 100 pounds of scrap and 1,150° F for 180 pounds of scrap have been achieved during the blows. As compared to cold scrap used in the normal BOF practice, it was found that by preheating scrap, usage could be increased by 43 percent. The thermal energy recovered by this preheating method can account for up to 44 percent of the energy necessary to melt the scrap.

Jan 1, 1974

By D. W. Frommer, M. M. Fine

"INTRODUCTION Laboratory mineral-dressing investigations covered by this report show that ores from Montgomery County, Ark., and Morgan County, Mo., are potential sources of barite and zinc. Fine grinding and froth flotation yielded drilling-grade barite from the former and chemical-grade barite and zinc concentrates from the latter.Samples from these deposits were subjected to a laboratory investigation to develop an economic and feasible treatment. The Arkansas ore, submitted by the Husky Refining Co., consisted of an intimate mixture of the economic mineral and quartz. Fine grinding and fatty acid flotation were utilized to effect a good recovery of a drilling-grade product. The other was a zinc-barite ore submitted by the Rocky Ford Mining Co., Stover, Mo. There was no problem in the recovery of zinc (most of which occurred as sphalerite), but the recovery of barite by flotation was complicated by the presence of gangue carbonates. Ultimately, an excellent recovery of barite was achieved with a relatively new type of flotation promoter, petroleum sulfonate.In recent years, barite has become one of the major industrial minerals as an essential ingredient in heavy drilling fluids, pigments, and chemicals. New sources of this important commodity are always interesting; thus, it is the purpose of this report to present information that may permit commercial exploitation of two deposits not in production."

May 1, 1952

By Graham W. Mark

A chemical method of analysis for beryllium was developed recently in Bureau of Mines laboratories. In this method, quinalizarin (1-2-5-8 tetrahydroxyanthraquinone) in N/4 NaOH is used as a colorimetric titration reagent. This solution has a reddish-purple color, whereas the solution containing equivalent amounts of beryllium and the dye is rather blue. In the titration procedure, standard quinalizarin solution is added to the unknown beryllium sample and to two standard beryllium samples of different but known concentrations. Then adjustments in concentrations of BeO in the two known and of quinalizarin in all three are made until the red-violet shade of the unknown is halfway between that of the two knowns. The amount of BeO in the unknown is calculated from the known BeO content of the solutions between which it lies. It is extremely difficult to distinguish the slight differences in shade of these solutions without the use of a proper light filter, especially when the concentration is over 0.1 mg. of BeO, so a study was made of the transmission characteristics of quinalizarin in N/4 NaOH and of the corresponding beryllium complex to determine what filter would give the most contrast.

Jan 1, 1950

By Walter K. Utt

The vibration levels of the heavy machines used in surface mining are much greater than for vehicles used on highways. In order to assure the proper functioning of electronic equipment placed on the surface mining vehicles, the U.S. Bureau of Mines has conducted a program of field measurements to define their vibration environment. The information in this report is for a class of vehicle that has a blade for scraping and wheels with rubber tires. The statistical information derived from these measurements can be used as a basis for laboratory testing to qualify equipment for a surface mining vehicle of this class. The envelope that would encompass 99 pct of the vibrations encountered in normal operations is presented for each location on the vehicle. The five locations for which data were recorded are the floor of the cab, the engine, the frame, the drive train (gear, differential, and torque converter), and the axle. Tabulated data are provided for those who wish to use a different probability level. The appropriate test profile for the laboratory testing can be determined from the information presented in this report.

Jan 1, 1993

By Victor E. Kral

"SUMMARYFollowing a magnetometer survey on the McCoy iron deposit, a trenching and drilling program was carried out by the Bureau of Mines in August 1944.This deposit is 32.3 miles southwest of Battle Mountain in the McCoy Mining District, Lander County, Nevada, and lies on the east flank of the Fish Creek Mountains at an altitude of 5,400 feet, about 1 1/2 miles south of the gold camp of McCoy.Total production from the deposit has been 400 tons of magnetite, mined by hand and shipped to the west coast for ship's ballast.Bureau drilled two holes to a total depth of 92 feet and excavated 12 feet of trenches. Both holes were drilled in the same ore body and engineered magnetite ore 14 and 11 feet thick. Trenching was used successfully to show the lateral limits of the ore.Magnetite ore bodies were found to occur as replacements of a limestone bed in quartzite. They outcrop near and parallel to the exposure of a diorite entrusting that forms a long westward-trending ridge. Although magnetic outcrops can be traced for 5,000 feet trenching definitely proved the ore bodies to be disconnected to have little or no lateral extent beyond their outcrops. Only two ore bodies more than 10 feet thick were found; one of these is the inaccessible to and the other was drilled by the Bureau."

Jan 1, 1947

By H. C. Ko

Calorimetric determinations of low-temperature heat capacities and the standard enthalpy of formation were made by the Bureau of Mines for aluminum sulfide, A12S3. The standard entropy (S°), enthalpy of formation (?Hf°), and calculated Gibbs energy of formation (?Gf°) at 298.15 K are 27.93±0.05 call deg-mole, -155.6±0.9 kcal/mole, and -153.0±1.0 kcal/mole, respectively.

Jan 1, 1976