Search Documents

By Albert W. Deurbrouck

This report describes the preparation characteristics of the significant, presently producing coalbeds in Mercer County, W. Va. Approximately 650,000 tons of coal was produced in Mercer County, W. Va., in 1960, of which over 630,000 tons was cleaned in four preparation plants. In 1960 the Pocahontas Nos. 3, 6, and 11 coalbeds supplied 99.5 percent of the total coal mined in the county. Because the number of working mines In this county was small, only six samples were collected; four of which were of metallurgical quality as mined. The remaining two samples could be upgraded by washing at suitable specific gravities. Many of the samples taken were of metallurgical quality as mined; however, the float-and-sink analysis on these coals has been included to point out their amenability to the production of premium quality, special purpose coals. In general the coals were low-volatile bituminous in rank with low ash and sulfur contents.

Jan 1, 1963

By Denise A. Herzog

The U.S. Bureau of Mines conducted a study of cyanide leach technology used in Alaska's mineral industry from 1987 through 1990. Literature and cost data were obtained for mines in the contiguous United States, Canada, and Alaska that use cyanide to recover gold and silver. The data was compiled in an effort to evaluate the economics and conditions associated with cyanide use in Alaska. This report discusses heap leaching methodology and evaluates a "typical" heap leach operation in Nevada and compares the results of the Nevada operation to an analogous hypothetical mine in Interior Alaska. Five daily tonnage rates were analyzed for both the Nevada and the Alaska operations to evaluate the spectrum of economic possibilities. The discounted cash flow rate of return (DCFROR) for each production rate was then evaluated in terms of recoverable metal value (RMV). The Nevada RMV for each production rate was then compared with its Alaskan counterpart, and the results averaged. The Alaskan production costs are an average of 1.71 times greater than costs associated with mining in Nevada at a 0% DCFROR. At 15% DCFROR, costs in Alaska are 2.01 times greater than those in Nevada. Costs are higher in Alaska because of the shorter leaching season, increased labor and transportation costs, and heavier precipitation and vegetation.

Jan 1, 1991

By Michael S. Miller

In 1985 and 1986, at the request of the U.S. Forest Service, the U.S. Bureau of Mines studied the 17,000-acre Pyramid Peak planning area in order to evaluate its identified mineral resources. The planning area is located in Riverside County, CA, 15 miles south of Palm Springs. The planning area contains marginally economic resources of marble and mica, subeconomic resources of garnet and occurrences of gold and tungsten. The area is underlain by marble, quartzite, schist, migmatite, intrusive rock, and a wide zone of intensely sheared rock. Quaternary stream, landslide, talus, and colluvial material overlie the older rocks. Ten claims for marble in or overlapping the southwest and southeast parts of the planning area are current (1986). Many other current claims are outside the planning area, adjacent to or within 2 miles of the southwest and southeast corners. Hundreds of millions of tons of inferred, marginally economic marble in and near the planning area may be mined for cement or lime after other developed resources near markets are depleted or if large-scale construction or other markets develop nearby.

Jan 1, 1987

By K. K. Kershner

This report describes an investigation by the Bureau of Mines designed to provide background data for extending and improving the applications of chlorine metallurgy in extracting metals from ores. Optimum conditions are given tor chloridizing galena, sphalerite, and chalcocite by contact with chlorine gas. Petrographic and chemical analyses of the sulfides used in the experiments are listed. Graphs are furnished showing the extent of chloridization of each metal sulfide over the temperature range of the observations. In each case, the first tests were made with the reaction chamber at room temperature. This temperature was increased by regular increments in succeeding tests until the temperature was reached at which quantitative conversion of the sulfide to chloride was observed. The data are also plotted for screen-size fractions of the sulfide minerals investigated. Data show that the extent of metal chloride formation was affected by chloridization time, particle size of the sample, and usually, the temperature of the reaction chamber. At 300° to 400° C. an anomaly was noted for both galena and sphalerite. The temperature at which this anomaly was observed varied according to the particle size of the mineral. Comparisons are made between the chloridizing characteristics of the mineral sulfides and their chemically prepared counterparts.

Jan 1, 1961

By T. T. Campbell

Studies were conducted by the Bureau of Mines to develop a process for preparing thorium-magnesium master alloys or pure thorium metal by magnesium reduction of thorium tetrachloride in a semicontinuous reactor. Thorium tetrachloride was prepared in a fluidized-bed reactor by chlorination of thorium oxide or thorium oxalate. Conditions were established for producing a suitable thorium oxide feed for a fluidized-bed reactor. Thorium tetra-chloride was purified by vacuum sublimation and subsequently reduced by magnesium in a semicontinuous reactor to form thorium-magnesium alloys. Relatively pure thorium was produced by removing magnesium from the alloys by vacuum sublimation. Close to 100 percent of the thorium fed into the reactor was recovered either as metal (~93 percent) or as thorium oxide (~7 percent). The oxide can be recycled directly into the process.

Jan 1, 1971

By R. Stefanko

The industrial hygiene and safety aspects with internal combustion engine in mining systems is truly interdisciplinary and encompasses many fields such as mine ventilation, exhaust gas and particulate analyses, mine atmospheric environment monitoring, mathematical modeling of generation, dilution and dispersion of pollutants in ventilation systems, and engine testing and approval. Mathematical models of the dilution and dispersion of diesel exhaust contaminants can be useful only if these models can be validated. In this research report, experiments that were specially designed for the above purpose are described. These experiments were conducted in the U.S. Bureau of Mines, Safety Research Coal Mine, in Bruceton, Pa. On the basis of this study, the data collected, and further review of available literature, it is concluded that mathematical models of dilution and dispersion are useful tools for mine ventilation planning. Additional objectives of this study about which conclusions and recommendations are reported here include: (a) evaluation of mine atmosphere contaminant monitoring systems; (b) optimum sampling site locations; (c) model sensitivity and error analyses; (d) computer coding of mathematical models; and (e) development of a diesel bibliography. While an extensive bibliography on diesels is provided in this report, Volume II of this final report has 511 references.

Jan 1, 1977

By Andrew A. Cochran

Laboratory-scale research was conducted by the Bureau of Mines to develop a new process for treating electroplating and other wastes. Various acid and alkaline cyanide wastes were combined under controlled conditions to neutralize the wastes and to almost completely precipitate the metals and cyanides. The metals were subsequently recovered for recycling; the cyanides can also be easily recycled. The process was successfully used to treat the major types of electroplating and etching wastes, containing Cd, Cr, Cu, Ni, and Zn, and to treat both concentrated and dilute wastes. The economic aspects of treating concentrated electroplating, etching, and anodizing wastes are especially attractive because of the low cost of mixing two wastes, the high value of the recovered metals, and the simplicity of the recovery procedures. The filtrates from the waste-plus-waste step were relatively harmless compared with the original wastes and met Public Health Service standards for free cyanide content. Free cyanide ions were not detected in most of the filtrates; the limit of detection was 0.03 ppm. Only small amounts of HCN were produced during the neutralization; the HCN was collected and neutralized.

Jan 1, 1974

By Charles L. Harness

Magnesia (MgO) has a variety of uses, and it has become increasingly important as a war material because of the imperative demand for refractories to line metallurgical furnaces, and because magnesia is used to make the in aircraft and other implements of warfare. Magnesia occurs as an integral part of nearly 60 minerals, but it is extracted commercially from only a .smaller number, of them. The present commercial sources are magnesite, brucite, dolomite, raw sea water, sea water bitterns, and well brines. Magnesia Raw Materials Magnesite magnesium, carbonate MgCO3, theoretically contains 47.8 percent MgO and 52.2 percent CO2. There are two varieties of magnesite, crystalline and cryptocrystalline (dense or amorphous). The latter type, though, not so plentiful as the former, is generally purer. It resembles unglazed write pottery in texture, whereas the crystalline variety is generally dark and granular, though the color may vary. The principal domestic deposits, of crystalline magnesite are near Chewelah, Stevens County, Wash. (which has supplied most of the magnesite mined in the United States), in the Gabbs Valley area of Nevada (near Luning); and in Llano County, Tex. Crypto-crystalline magnesite occurs principally in California. Magnesite occurrences have also been reported in several other States, including New Mexico, New York, New Jersey, Pennsylvania, Massachusetts, Vermont, and Maryland, but these deposits have not been developed commercially.

Jan 1, 1943

By R. Craig Smith

The Bureau of Mines conducted a study of production costs for the secondary lead industry and determined costs for present, pending, and proposed environmental legislation. Operating costs for smelters by capacity groups range from 16.8 to 19.6 ¢!lb of refined lead. Present regulatory compliance costs for these groups range from 2.2 to 2.4 ¢!lb. Pending compliance costs could add 3.5 ¢!lb of refined lead, and proposed regulations could add another 1.3 ¢!lb. The individual capital costs necessary to comply with pending environmental regulations are estimated to be $1.8 million for small smelters and $10.4 million for large smelters. Proposed regulations could require additional expenditures from $1.9 million for small smelters to $4.9 million for large smelters. These cost estimates, based on average 1985 dollars, indicate that pending and proposed legislation could add significantly to capital and operating costs of the secondary lead industry. These regulatory compliance costs may result in a loss of up to 40 pet of secondary lead production capacity.

Jan 1, 1987

By Steven J. Schatzel

Gas drainage through surface bore-holes has been the conventional means of methane control for U.S. longwall gobs. However, these vertical boreholes are becoming so costly, and the surface rights so difficult to obtain, that the Bureau of Mines is developing underground gob gas drainage as an alternate means of methane control for U.S. longwalls. Holes are drilled into the roof over the panel and on retreating longwalls, towards the working face from a location inby the face. As the longwall retreats, an increasing portion of the hole intercepts the fracture system over the caved gob. A surface exhauster maintains a vacuum on a pipeline parelleling the panel and draws the methane mixture out of the mine. Auxiliary systems of gob gas drain-age during longwall mining will be essential for an increasing number of coal mines. Deep and gassy mines often find ventilation insufficient for adequate dilution of methane in bleeder entries. Although this cross-measure method of degasification has been used successfully in Europe, some of the European techniques cannot be directly applied to U.S. mines. This is the first study of its kind in this country.

Jan 1, 1982

During the summer of 1973 we were asked to perform a theoretical investigation of the propagation of low frequency (LF) radio waves down deep (10,000 feet) hoistshafts* for the case where the hoist cable ("rope") is the only metal conductor present. Propagation is by means of the TEM coaxial mode of transmission in which the hoist cable serves as the inner conductor and the surrounding rock acts as the outer conductor. Since the rock is a relatively poor electrical conductor the current in the outer conductor of the coaxial line is not confined to a very thin surface layer as in a metal coaxial cable, but spreads radially to a distance that is generally many times the shaft diameter. This feature of the wave propagation requires a more sophisticated theoretical treatment than the approximate skin-depth theory that is adequate for metal coaxial lines. In this Part we treat the hoist shaft wave propagation loss, characteristic impedance, and the field current distributions in the surrounding rock medium. We also show that the large penetration of the wave into the rock outer conductor does not present a difficult problem with regard to coupling the transmitter or receiver to the transmission line with a minimum of insertion loss, but that the large impedance mismatch caused by the capacitance termination between the cage and shaft wall may well be the most significant contribution to overall system loss. Inductive coupling and impedance matching to the hoist rope/shaft transmission line are also treated briefly. Preliminary results indicate that a broad minimum in overall system loss should occur between 100 kHz and 1 MHz, possibly centered around 300 kHz. Further work is needed to better quantify this signal loss behavior, compare it with hoist shaft electromagnetic noise spectral data recently acquired by NBS, and identify the most favorable operating frequencies.

Jan 1, 1974

By Charles Vaught

This is the second in a series of four articles that discuss underground firefighting preparedness. As with the first article in the May-June issue, it is based on interviews with 214 miners conducted at 7 underground mines (?A? through ?G?) by researchers of the National Institute for Occupational Safety and Health?s (NIOSH) Pittsburgh Research Center [Vaught et al. 1996].In the first article, the authors presented an overview of the study conducted by NIOSH on mine fire response preparedness and provided a general perspective on underground mine fires. In this article, we will describe miners? preparedness to evacuate a fire and their experience with incipient fires.

Jan 1, 1997

By Thomas M. Barczak

This U.S. Bureau of Mines report describes methods to enhance the capacity, stiffness, and timber utilization of wood crib supports. Since stiffer supports minimize strata deflections that contribute to roof instability, efforts to maximize crib stiffness while maintaining stability through a wide displacement range should be a design priority. The stiffness and capacity of conventional crib designs, employing alternating layers of wood timbers that are loaded perpendicular to the grain, can be increased by increasing the interlayer contact area or by using higher strength wood. Contact area can be increased by using wider timbers or employing more timbers per layer. Concepts that provide parallel-to-the-grain timber loading will provide substantial increases in crib stiffness and capacity. Two concepts that utilize this principle are examined: (1) an original South African design that constructs wood cribs from preformed layers (mats) of timber where short blocks are oriented vertically between horizontal slabs; and (2) a design that employs full lengths of timber placed vertically in the interior of a conventional crib structure. These designs also provide more efficient timber utilization by providing greater support capacity per volume of wood used in the crib construction.

Jan 1, 2010

By Frank E. Cash

"INTRODUCTION The producing iron-ore ranges in the Lake Superior district are the Marquette and Menominee in Michigan, the Gogebic in Michigan and Wisconsin, and the Cuyuna, Mesabi, and Vermilion in Minnesota. These ranges produce about 85 percent of the iron ore mined in the United States. The accident experience in connection with this production is better than that of the regions producing the remaining 15 percent. Production and shipments vary slightly from year to year owing to stockpiling underground ore during the winter, or nonshipping, season but closely approximate each other over a period of years. This information circular supplements, combines, and continues the data contained in Information Circulars 7321 3/ and 7410 4/, including statistics for 1946 and 1947.Whereas the title ""Accident Experience"" is used for uniformity and logical indexing throughout this report, ""injury"" will be used as a general term to apply to disabilities of all degrees.During the 8-year period 1940 to 1947, inclusive, 619,054,023 long tons of iron ore was shipped from the Lake Superior district. 5/ Michigan and Wisconsin shipped 117,828,939 tons, or 19.03 percent of the total, and employed approximately 9,260 men. Minnesota shipped 501,225,084 tons, or 80.97 percent of the total, and employed an approximate annual average of 12,260 men. The tons produced and shipped per man employed in Minnesota is much greater than in Michigan and Wisconsin, owing to the large open-cut production in Minnesota."

Jun 1, 1949

By R. M. GRANTHAM, J. H. SOULE

C. R. Keyes, F. C. Schrader , F. A. Jones ( the first director of the New Mexico School of Mines , whose name was given the deposits ) , and N. H. Darton all described the Jones iron deposits within a decade after their discovery in 1902 . The earliest locations now on record were made in 1927. Interest in iron ores was revived during the second World War . Paul E. Pesonen , of the Bureau of Mines , reported on the deposits in December 1941 and proposed an extensive exploratory program . In March 1942 , the deposit was reported upon by C. H. Johnson , also of the Bureau of Mines , and a definite program of exploration was outlined .

Feb 1, 1947

By John P. Walsted

Because of the absence of an iron-producing industry, the Pacific Northwest is working under an economic handicap. This is particularly apparent in the gray-iron-foundry industry because of the high price of pig iron imported from foreign sources or shipped in from producing ?areas within the United States. The high prices and sometimes short supply of ferrous metal products has put a brake on industrialization, which has been only partly compensated by the availability of cheap electric power. The economic condition of the gray-iron-foundry industry could be improved by establishing a small iron-producing industry based on the locally available ores. Moreover, establishing a local iron smelter would create a market for resources now dormant. Low-grade ores of manganese, chromium, and nickel would become usable in industry when combined with the iron ore from Scappoose. Pig iron produced in even limited quantities would level out the fluctuation in supply. The ore deposits, being small, would not supply enough pig iron to satisfy the entire demand. This condition necessitates designing special pig irons that will carry abnormally high proportions of scrap in the cupola charge.

Jan 1, 1955

By Clarence O. Babcock

This report describes the results of Bureau of Mines laboratory and preliminary field tests on a rock bolt of helical shape. The flexible construction allows the bolt to maintain a more stable load level than is possible with a straight bolt. Bolt load changes resulting from anchor slippage, blasting shock, or changes in mine geometry with mining advance are minimized. Preliminary field tests were performed at the Kaiser Steel York Canyon mine where the load changes of straight and helical bolts were measured using a vibrating-wire load gage. The field tests were performed to establish the viability of the concept of a helical bolt. The practical usefulness in terms of performance and economics remains to be shown. The change in bolt load for the flexible bolts was one-third that for the straight bolts. There were no malfunctions of the gage, and the bolts maintained a more uniform load than the straight bolts used as controls.

Jan 1, 1978

Various aspects of judgment and decision-making are key themes in this book. The model presented here serves as a loose structure for the chapters that follow this one. The notion of a model is introduced because growing research interest in the subjective aspects of group and individual behavior has led to a debate over whether judgment is a skill that can be understood scientifically. A related point of contention is whether such an understanding could lead to the development of methods for estimating people's ability to make good decisions during an emergency. There is some literature that supports the potential usefulness of this approach. However, little agreement seems to have been reached on how to define and operationalize even those basic concepts necessary to assess the soundness of decisions from within their environmental and group contexts [Jensen and Benel 1977; Godden and Baddeley 1979; Baumann and Bourbonnais 1982; Brecke 1982; Stone et al. 1985]. A look at the real-world process is clearly needed. The need to attempt a better understanding of judgment and decision-making properties stems from those occasions in the existence of an organization when there is a lot at stake. The process of decision-making (which is part of the exercise of judgment) has been analyzed in situations such as corporate takeovers [Janis and Mann1977], military combat [Begland1979], clinical emergencies [Baumann and Bourbonnais 1982], and aviation events [Billings and Reynard1984]. The fundamental assumption of these analyses is that, while there are untold successes, there are also notable numbers of failures resulting from decisions that can be ascribed to one or more errors in judgment. From a cognitive perspective, any person engaged in decision-making (either alone or in a group) is actively involved in a process characterized by certain elements. These were mentioned in chapter 1, but are reiterated briefly at this point: (1) detection of a problem, (2) definition or diagnosis, (3) consideration of available options, (4) choice of what is perceived as the best option given recognized needs, and (5) execution of the choice based on what has transpired [Flathers et al. 1982; Baumann and Bourbonnais 1982]. At any moment in this process, there are factors at play that have a large impact on one's ability to solve complex problems in a limited time: (1) an internal state [Hedge and Lawson 1979] is the sum of a person's psychomotor skills, knowledge, attitudes, etc.; (2) uncertainty [Brecke 1982] is caused by faulty or incomplete information received from the external environment; (3) stress [Biggs 1968; Jensen and Benel 1977] is generated both by the problem at hand and any background problem that may exist; and (4) complexity, as it is used here, refers to the number of elements involved that must be attended to. These variables are depicted in figure 5.1, and their relationship to each other and to an outcome is indicated. This schema is designed to suggest interaction, because while the judgment and decision-making process may be conceptualized as discrete stages, experience tells us that this is not the way people function in real-world situations.

Jan 1, 2000

By M. B. Bransford

A calculation procedure was evolved by the Bureau of Mines for determining the heat-transfer characteristics of dilute gas-solid mixtures in an externally heated tube. The procedure accounts for differences in gas and particle velocities and covers a range of particle sizes. Heat transfer coefficients obtained by the calculation procedure are compared with values reported in the literature.

Jan 1, 1970

By J. F. McIlwain

As part of its goal to minimize the requirements for critical materials, the Federal Bureau of Mines has investigated the consolidation of an iron-base superalloy (20 pct Cr, 5 pct each Ni and Mn, 1 pct each C, W, Mo, and Cb, and the balance Fe) and its modifications by powder metallurgy (P/M) techniques. Vacuum-atomized, prealloyed powder was used. Consolidation was by sintering of cold-pressed alloy powder, or by forging plus rolling or extrusion of canned powder. Several commercial lubricants were evaluated in the pressing operation. At 50-tsi compacting pressure with up to 3 wt-pct lubricant, green strengths did not exceed 1,000 psi. Powder sintered just below the solidus temperature attained a tensile strength of 69,000 psi and 4 pct elongation. Liquid-phase sintering produced higher densities, lower tensile strengths, and nil ductility. Canned powder was forged and rolled at 1,200° C, yielding a 100-hr rup¬ture strength of 9,800 psi at 815° C and a room-temperature tensile strength of >130,000 psi at 6 pct elongation. Heat treatment of modified P/M iron-base alloy containing 0.63 pct C resulted in a 100-hr rupture strength of 17,000 psi. Oxidation resistance at 805° to 815° C of the forged and rolled P/M iron-base alloy was similar to that of the cast iron-base alloy and supe¬rior to conventional stainless steels.

Jan 1, 1981