Search Documents

Rock mass classification is widely used throughout the underground mining industry—in both coal and hard-rock mines. The technique has been successful because it— • Uses simple measurements to rate rock mass strength. • Helps mine planners to make the best use of geologic information in mine design. • Makes it possible to compare ground control experiences between mines, even when the geologic conditions are very different.

Jul 1, 2007

By R. J. Tocher

Uniaxial testing was performed on coal specimens to determine the time-dependent response. The testing was carried out on coal from six mine sites throughout the Western United States and Pennsylvania. Testing configurations were varied to allow analysis of moisture dependency, stress level and specimen orientation. Several theories were presented for the behavior of coal due to moisture diffusion. Experimental results showed the correlation between the theories and the actual material response. Coal deformation was found to be highly dependent on the moisture level of the testing environment. Moisture migration causes drying and shrinkage which lead to progressive degradation of the material. The coal tested experienced a rebound if saturated after a period of drying. This type of time-dependent behavior overshadows the dependence on the applied stress level, which, however, still produces a noticeable creep behavior. Analysis of one series of creep test results was performed. A relationship was developed on the basis of a simplified rheological model to describe the coal response to uniaxial stress. Previous empirical formulations in the form of power laws were compared and their deficiencies pointed out.

Jan 1, 1980

By Arno C. Fieldner

Coal for coke production is fundamentally necessary for the manufacture of pig iron , and pig iron must be had for making steel - a vital element in our modern industrial economy . In both World Wars , special effort by Government and industry was required to meet the emergency of greatly increased demands . In the first World War , lack of coke - oven capacity , rather than lack of coking coals , was the principal problem ; but in the second World War both oven capacity and coking -coal mining capacity were pushed to the utmost . Because of inadequate supply , it became necessary to allocate a part of the production of these coals from other fuel use to coke production . This was done by the Solid Fuels Administration . These experiences raised a question , during and after the war, as to the nature and amount of the minable reserves of coking coal suitable for the manufacture of metallurgical coke ; and to what extent the lower -rank and lowergrade coals could be utilized by improving preparation and by appropriately blonding different coals . Obviously , much investigation and research are required to find answers to these questions . Somo work was done by Governmental and industrial agencies during the war , and , fortunately , more has been undertaken since the close of It is the purpose of this paper to review briefly our fuel reserves , with special reference to coking coal , and to discuss the problems of utiliz . ing progressively poorer coking coals as the reserves of high - quality coals approach depletion .

Mar 1, 1950

By Paul W. Johnson, Ralph C. Kirby, Frank A. Peters

An evaluation is presented for a process designed , on the basis of published work , to extract alumina as potassium alum from clay using sulfuric acid and potassium sulfate . The silica residue is separated by filtration . Ferric iron is reduced to ferrous iron , and the alum is crystallized from the solution , leaving the ferrous iron in solution . The alum crystals are separated from the solution and redissolved for feed to autoclave decomposition . In an autoclave the alum is partly decomposed to a basic alum , recovering five - ninths of the sulfuric acid and two - thirds of the potassium sulfate without using an acid plant . The basic alum is decomposed by calcining , and the potassium sulfate is then removed by washing with water . Operating costs for a plant producing 1,000 tons of alumina a day are estimated at $ 96.15 per ton of alumina . The fixed capital cost is estimated at $ 155 million . This process is not competitive under current economic conditions with the production of alumina from bauxite by the Bayer process . Improvement in leaching , basic alum decomposition , and washing could reduce the costs and improve the product which contains some potassium .

Jan 1, 1963

By Nadia C. Miller

In situ stope leaching is an innovative mining system that reduces the surface impacts of conventional underground mining. As in any leaching operation, stope leaching requires hydrologic site characterization and control of leaching solutions. Several tracer tests, using sodium chloride (NaCl) in various concentrations, were conducted by the U.S. Bureau of Mines (USBM) in an underground experimental stope to simulate a leaching environment. The tests were conducted in fractured crystalline rock that was partially water-saturated. As tests progressed, the surrounding fractures became more saturated. A predominant flow direction away from the stope was found during testing. Testing procedures, results, and a remediation plan for in situ leaching based on field observations are presented in this report.

Jan 1, 2010

By D. Harrington

"In at least three out of every four working faces in metal mines there is no attempt made to cause air circulation other than by use of compressed air, and in at least nine cases out of ten the compressed air is released merely by opening, or partly opening, the valve and allowing the compressed air to escape through open air hose used to convey the compressed air to the drilling machines. Usually no blowers are in use during periods of drilling, as the exhaust from the drill provides cool, comparatively fresh air for the driller; however, in some instances, the compressed-air line is provided with a tea connection, which permits taking air for the drill from one side of the tee, and air for ventilation through a separate hose used as a blower, simultaneously with drilling.Table 1 contains temperature and humidity data as to compressed-air blowers from open end of air hose at 36 working places in eleven metal mines of four States, embracing the mining of gold, silver, copper, lead and zinc ores, and at horizons ranging from 500 feet below the surface to as low as 4900 feet.It is noticed that the ordinary air surrounding the worker at the face gives an average wet bulb temperature of 81.7° F. for the 36 working faces, with 84.7° F. dry bulb and 87.2 per cent relative humidity. The average wet bulb tem¬perature of 36 readings at these working faces of compressed air at the end of the,hose as the air issues from the hose was 67.4° F., or 14.3 degrees lower than the average wet bulb readings of the air of the working places; however, the average dry bulb temperature of the 36 readings of compressed air as it issued from the end of the hose was 79.7° F., or only 5 degrees less than that of the general air (84.7°); the relative humidity was 51.1 per cent as against 87.2 per cent for the surrounding air. Readings were taken in five raises, seven crosscuts, ten drifts and 14 stopes.It will be noted that the velocity or movement of the general atmosphere at each of the entire 36 working faces, was found to be practically imperceptible; this might readily be inferred since compressed air is rarely used on blowers if there is adequate circulation of the general air of the place. Where rook temperatures could be obtained readily, they are shown; it is noticeable that the dry bulb temperature of the air of the working place varies little from the rock temperature, and that the dry bulb temperature of the compressed air as it issues from end of air hose varies only a few degrees from the temperature of the surrounding rock; in some instances the dry bulb temperature of the compressed air as it issued from the end of the air hose was higher than the rock temperature or the dry bulb temperature of the surrounding air."

May 1, 1921

By Eric R. Bauer

This Bureau of Mines manual is intended to provide a better understanding of ground movement and the technology available for measuring it, The manual deals with convergence, strata separation, lateral roof movement, stress, and support load in underground mines. The instruments that measure these ground control parameters are described in detail. Step-by-step procedures for selecting the appropriate instrument are presented, which consider such factors as approximate cost, installation procedures, data collection, and data interpretation; and an instrument selection worksheet is provided to facilitate the instrument selection process. Actual instrument case studies and a list of instrument suppliers are presented in the appendixes.

Jan 1, 1985

By E. G. Davis

Under a memorandum of agreement with Reynolds Metals Co., Richmond, VA, the Bureau of Mines studied the problem of corundum formation on refractory linings in aluminum recycling furnaces. A laboratory test was developed for evaluating refractories in contact with molten recycled aluminum and identifying the mechanism of corundum formation. A test apparatus was designed and constructed to evaluate the performance of refractory samples. Corundum mechanism formation studies indicated that corundum formed on refractories when there is metal penetration. Once corundum forms, it acts as a wick allowing the molten aluminum to move to the surface where it is oxidized, thus causing further growth of the corundum. Phosphoric acid treatment or a spinel mortar coating prevented corundum formation on the 70-and 90-pct-A1203 refractories.

Jan 1, 1988

By D. W. Boley

This report contains the results of an analysis of the Logan oilfield, Hocking County, Ohio, and predicts the recovery of oil from the Clinton sand by waterflooding. Core analyses, electrical and radioactivity well-survey logs, reservoir-fluid analysis, and geologic and production data were used for this study. Considered in the evaluation were the reservoir geometry, depth, lithology, continuity of the rock properties, fluid saturations, fluid characteristics, rock wettability, and relative permeability-fluid saturation relationships. The study indicates that a properly engineered waterflood should recover approximately 135 barrels per acre-foot of effective sand. The predicted recovery warrants the initiation of a pilot waterflood in this field.

Jan 1, 1965

By Danqing Xu, A. W. Khair

"This paper presents a laboratory simulation of regrinding and resulting dust generation. An Automated Rotary Coal Cutting Simulator (ARCCS) was modified to conduct regrinding experiment. In order to estimate the effects of coal properties and operating parameters on regrinding and dust generation, an orthogonal fractional factorial experimental design was implemented in regrinding experiment. Marple personal cascade impactors, Series 290, were used to measure dust concentration during experiment. Three types of coal seams, namely, Waynesburg, Pittsburgh, and Lower Kittanning, were used to represent different coal properties. Experimental results and complete parametric analysis were presented.In a rotary cutting system, all the broken coal and part of the remaining coal from previous cutting cycles must be transported through part or entire circumference of the cutting drum. This transportation of already recovered coal through the cutting zone of rotary head makes it a rotary grinder. Some of the coal particles will be subjected to secondary fragmentation or regrinding in the process. The potential effect on dust generation by regrinding is significant because the cutting head utilizes kinetic energy to comminute recov¬ered coal material. The moving bits and bit blocks on the cutting head impact coal particles and transfer some of their kinetic energy to the particles. After obtaining kinetic energy, coal particles are free to impact one another and they also impact the coal seam or cutting head. During impact, high impact force and high internal stress concentration are created in the particles. Kinetic energy is transformed into strain energy. When stored strain energy exceeds allowable strain energy, the particles will break. A great amount of respirable dust will be generated due to impact failure. In reality, regrinding occurs at the same time as primary cutting. The particles to be ground are the result of primary cutting. Both primary cutting and regrinding produce dust. Therefore, it is impossible to separate regrinding from primary cutting. In order to study respirable dust generation by regrinding and analyze the influencing parameters, a laboratory approach was adopted. In this approach, it is possible to study the regrinding separating from primary cutting."

Mar 1, 1992

By Tobias W. Goodman, George N. Aul, Joseph Cervik

The Bureau of Mines conducted research to degasify a virgin block of coal in the Beckley Coalbed using long horizontal holes drilled in an array from the bottom of a ventilation air shaft. Eight horizontal holes and an in situ pressure hole were drilled in a radial pattern to depths ranging from 418 to 910 ft (127 to 277 m) and 205 ft (62 m), respectively. The investigation showed the shaft was in a basin saturated with water, which resulted in low gas flows from holes. The in situ pressure at 200 ft (61 m) into the coalbed was 79 psig (544.6 KN/m2). The aver- age gas and water flows for the eight holes were 94,100 ft3/day (2,665 m3/day) and 13 gal/min (49.3 l/min) . After 514 days of degasification, 18.7 million ft3 (0.53 million m3) of gas had been drained. Methane face emissions, which were measured as a section advanced toward the shaft, were reduced about 77 pct, emphasizing the value of drainage by this technique. All holes were grouted before the area around the shaft was mined.

Jan 1, 1982

By Lucien Eaton

This paper describing the mining practices at Mine No. 1, Menominee Range, Mich., is one of a. series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. It is felt that the publication of this information will be of interest and value to the mining industry at large and especially to operators whose mining conditions are similar to those described. ACKNOWLEDGMENTS The author is indebted to the superintendent, engineer, and mining captain of Mine No. 1 for much of the information presented.

Jan 1, 1929

By Thomas R. Bur

The patterns of variation of the 21 anisotropic elastic constants with direction arc presented for all of the symmetry systems that are normally expected to occur in rocks and in the constituent minerals. The exception, which is not discussed, is the triclinic system for which no elastic constants are available. Variations are shown for rotations about the principal axes by means of polar graphs. These include graphs for all of the n-fold symmetry axes possible for elastic symmetry and thus make it possible to visualize variational patterns for rotations about any n-fold axis. Variations throughout space are shown by means of equal area projections for the only constants (those relating axial stress to axial strain) that are uniquely defined by a single closed surface. For those unfamiliar with the compliance (Sij) and stiffness (cij) coefficients, the variations that can be shown by Young's modulus (E), Poisson's ratio (v), and shear modulus (G) are also given.

Jan 1, 2012

By Thomas J. Peters

In 1987, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the 15,174-acre Sleeping Giant study area, including the 6,112-acre Wilderness Study Area (MT-075-111), in order to evaluate its identified mineral resources. The study area is located in Lewis and Clark County, MT, about 30 miles north of Helena. Sleeping Giant Mountain trends west-northwest from the Missouri to the eastern crest of Little Prickly Pear Canyon (the route of Interstate 15), and has several summits over 6,000 ft. Geologically, the area is in the Disturbed Belt, and a large block of Middle Precambrian metasedimentary siltstone and underlying shale has been thrust northeast over younger, sedimentdry volcanic and intrusive rocks.

Jan 1, 1988

By John B. Gayle

During studies of the various methods for determining and specifying the factors that indicate whether a particular coke is better or worse than other cokes for metallurgical uses, questions arose as to the precision of screen-analysis tests on coke. Although the usual index of precision, the standard deviation of the test result, gives a measure of the precision of these data, the experimental determination of the standard deviation for a particular set of conditions requires tests on a large number of duplicate samples. Because this procedure necessaily involves a great deal of labor, an equation for predicting standard deviations from theoretical considerations has been developed. Results predicted with this equation agree satisfactorily with the experimental values and are applicable to tests on coal, coke, gravel, and other bulk materials.

Jan 1, 1952

By Jr. Watts, B. K. Cantrell, D. H. Carlson, K. L. Rubow

"The use of diesel equipment in underground coal mines is controversial because ""whole diesel exhaust"" is regarded as ""a potential occupational carcinogen"" by the National Institute for Occupational Safety and Health (NIOSH). Threshold limit values (TLVs) are recommended for the gaseous pollutants; CO, CO2, NO, NO2, SO2, and some hydrocarbons emitted in diesel exhaust. There is, however, no TLV recommended for diesel exhaust aerosols (DEA) nor is there a standard method for sampling these aerosols.The University of Minnesota and the Bureau of Mines have collaborated to develop a personal diesel exhaust aerosol sampler (PDEAS) which utilizes size selective, inertial impaction and gravimetric analysis. During the field tests of this sampler, numerous air quality measurements were conducted in underground coal mines using diesel equipment. The objective of this report is to present these data and to assess the impact of diesel face haulage equipment on mine air quality.Air quality data were collected in four underground coal mines using continuous mining methods with diesel haulage equipment. Daily samples were collected at the section intake, haulageway, and on haulage vehicles. Both full-and partial-shift samples were collected using a variety of aerosol instruments, including the PDEAS and the micro-orifice, uniform deposit impactor (MOUDI) which sample the mine aerosol diesel exhaust fraction. Two of the mines were also monitored for the major gaseous constituents found in diesel exhaust CO, CO2, NO, NO2, and SO2. These measurements were made by either collecting bag samples for subsequent gas analysis or by Palmes dosimeters.The concentrations of CO, CO2, NO, NO2, and SO2, were well below regulated levels. The mine average DEA concentration determined by the PDEAS in the haulageway for the three mines surveyed using this instrument was 0.79 mg/m3, with a standard deviation of 0.19 mg/m3. DEA contributed 65% of the respirable aerosol, at this location. These results were the same as the mean DEA concentrations calculated from size distribution measurements obtained using the MOUDI. This was 0.78 mg/m3, with a standard deviation of 0.22 mg/m3."

Mar 1, 1992

By P. Nicholls

[This paper sets forth the burning characteristics of coke used as a domestic fuel as shown by work of the U. S. Bureau of Mines and others. Coke is a truly smokeless solid fuel and is held in high regard for this quality. Ways are being found for making commercial coke from a wider range of cools than heretofore, and tale use of coke for domestic heating is increasing. ACKNOWLEDGMENTS The experimental work reported in this paper was conducted at the Pittsburgh Experiment Station of the U. S. Bureau of Mines cinder the authority of O. P. Hood, chief mechanical engineer; M. L. Orr, assistant feels engineer, and W. M. Brewer, junior fuels engineer, assisted by Charles Schramm cooperated in making the tests.]

Jan 1, 1929

By R. D. Groves

Techniques were developed for preparing metallurgical-grade copper powder from industrially produced cement copper. Flotation was used for rejecting discrete gangue particles, acid leaching to remove residual iron and aluminum, hydrogen reduction to eliminate oxygen, sintering to consolidate the fine-sized copper, and grinding to obtain copper powder. Powders prepared from six different cement copper samples contained, in percent, 98.5 to 99.0 Cu, 0.10 to 0.05 Fe, 0.10 to 0.08 insoluble material and the remaining individual impurities less than 0.15 percent. The apparent density, flow characteristics, and other physical properties were suitable for powder metallurgy applications. An economic evaluation showed that this process was economically feasible. Processing costs appeared modest when considering that copper powder commands a price normally about 17.5 cents per pound over that of electrolytic copper.

Jan 1, 1971

By H. G. Miller

The success of any project in which gas is injected into oil-producing sands to increase the current rate or the economic ultimate production of oil or in which surplus gas from oil-producing operations is stored temporarily in reservoir sands that have been wholly or partly depleted of their producible oil depends mainly upon an understanding of the underground movements of oil, water, and injected gas and the ability to control their speed and direction of migration through the reservoir sends. Many operators believe that injected gas always travels up the structure and drives oil to wells structurally higher than the injection wells, because the specific gravity of the injected gas is less than that of the fluid substances in the formation. Consequently, many injection wells are located on the flanks of oil-bearing structures with the idea of utilizing the energy of the injected gas to drive the oil to producing wells higher on the structure. It is true, under certain conditions of pressure and fluid depletion of the reservoir sands that injected gas will move in an up-structure direction, but the theory that injected gas always moves up the structure is based on an erroneous conception of the laws that pertain to the expansion of gases. By definition, "a gas is distinguished by its property of infinite expansion and is limited in volume only by the walls of the vessel which contains it." The expansion of gas that is injected into reservoir sands also is limited by "walls" that surround the space influenced by the injected gas. The walls of the majority of undrilled or virgin oil-bearing reservoirs in California are the impervious shales overlying and underlying the productive strata and the "dams" or effective barriers of edge water around the rims of the reservoirs. When gas is injected into the sands of a producing reservoir, regardless of the location of the injection well on the structure or the degree of depletion of oil from the sands, one of the walls which confine the gas in the structure about the injection well is fluid. This wall will be edge water in a nearly depleted reservoir, where the drainage cones or regions of reduced pressure about injection and producing wells intersect; and, where there is no interference of drainage cones and the injection well is structurally above the edge water, the wall will be oil. In some producing reservoirs bottom water may be the lower wall of the space that confines the gas about injection wells, but the effect of bottom water on limiting the expansion of gas is the same as if the water was not present and impervious formation separated the producing from the underlying nonproducing strata. Therefore, since compressed gas always seeks regions of reduced pressure and its final volume is limited only by formation and fluid barriers and since the force exerted by the gas under pressure is equal in all directions, the course of migration of injected gas in reservoir sands in California and the effect of the gas pressure on fluid movement does not depend necessarily upon the up-structure location of low-pressure regions.

Jan 1, 1932

By R. V. Lundquist, A. E. Morris, E. L. Singleton

This experimental research was performed to determine rate - of - reaction constants on the MnO - C and Mn , C₂ - 3MnO systems at 1,100 ° , 1,150 ° , and 1,185 ° C. Reactions were conducted at atmospheric pressure under controlled flow of purified helium through the furnace chamber . The weight - loss method defined reduction percentages , and reaction products were identified by X- ray methods . The system Mn0 - C followed a linear reaction rate , and experimental results produced an apparent activation energy of 55.8 kcal per mole of Mn0 . The system Mn, C - 3Mn0 followed a parabolic rate of reaction law and yielded an apparent activation energy of 114.4 kcal per mole for the reaction .

Jan 1, 1964