Search Documents

By E. G. Davis, H. P. LeVan, L. S. Smith

Leaching of a Georgia umber ore when using both ferrous sulfate and pickle liquor was studied in the laboratory . The ferrous sulfate content of the leach solution was the major factor affecting the extraction of manganese from the ore . Time , temperature , and the sulfuric acid content of the leach solutions had relatively little effect on leaching of manganese from the ore ; however , these factors did affect the amount of iron extracted from the umber and/or precipitated from solution . Simulated countercurrent leaching of the ore with pickle liquor containing 130 gpl (grams per liter ) ferrous sulfate ( 48 gpl ferrous iron ) produced a pregnant solution having 16 gpl manganese and 41 gpl iron . Filtration tests of the leach slurries indicated that separating the leach solution and solids by vacuum filtration was impractical , whereas pressure filtration was feasible when the cake thickness was limited to about three- fourths of an inch . Fired pellets of the filter cake yielded a firm , hard product analyzing 56 percent iron and less than 0.1 percent sulfur .

Jan 1, 1964

By M. R. Geer

The widespread adoption during the past decade of the dense-medium process for cleaning coal increases the need for technologic studies of the process. Such studies provide information that will insure maximum usefulness of this process in its present form and may well lead to substantial improvements in design and opera¬tion. The Bureau of Mines has published the results of cleaning trials on a wide variety of coals in two dense-medium pilot plants5/ and reported the recovery of coal from waste by dense-medium treatment.6./ The present report deals with the viscosity of magnetite dense medium, an important subject about which virtually nothing has been published. Specifically, the report concerns methods for measuring viscosity, the influence of various medium contaminants on viscosity, the effect of viscosity on cleaning results, and the influence of viscosity on consumption of medium. Cleaning trials on four coals of varied density composition in a pilot plant, using mediums of different viscosities, showed a steady reduction in cleaning efficiency with increasing viscosity in every instance. However, the behavior of each coal in a viscous medium was distinctly individual. With one, an increase of only 1 centipoise in viscosity caused a reduction in recovery efficiency of 7.7 percent, whereas the same increase in viscosity with another reduced recovery efficiency only 2.7 percent.

Jan 1, 1957

By George T. Faust

The petrographic microscope plays an important role in the mineral dressing of nonmetallic materials. Petrographers and mineral technologists have evinced an interest in the technique developed, specifically, for mineral-dressing problems. The following dissertation makes the informa¬tion more generally available. ACKNOWLEDGMENTS The authors are indebted to O. C. Ralston, chief engineer, Nonmetals Division, and to Will H. Coghill, supervising engineer of the Southern Experiment Station for a critical reading of the manuscript. They are also indebted to their colleagues for technical information obtained in the course of cooperative work, in particular to J. B. Clemmer for the use of the data on fluorite.

Jan 1, 1940

By Irving Hartmann

At the 9th International Conference of Directors of Safety in Mines Research a paper6/ was presented describing the initial phases of research by the Safety in Mines Research Establishment at Buxton, England, on the remote control of timber fires with high-expansion foam plugs in a rock tunnel. The work received extensive publicity, and great interest was aroused by the implied possibility that the method might be used successfully to control coal-mine fires, which for various reasons cannot be approached and attacked by standard fire fighting measures and frequently require sealing extensive, valuable coal properties and lead to loss of production and coal reserves and occasionally loss of lives. To investigate the practicability of the foam-plug technique under American min¬ing conditions, with room-and-pillar-type extraction and multiple entries, the Bureau of Mines in 1957 began an investigation at its Experimental Coal Mine, Bruceton, Pa, In preparation for this work it was necessary to rehabilitate and reinforce an elliptical tunnel in the mine where studies had been made, many years ago, leading to development of a ventilation system used in the Holland Tunnels between New York and New Jersey, and in many other vehicular tunnels.

Jan 1, 1958

By John B. Bennett

In this report estimates are presented of the impact of the passage of five recently proposed "acid rain" bills on electric utility costs for coal-burning utilities servicing the domestic aluminum smelting industry, and on the costs of production for affected aluminum smelters. As aluminum smelting is an energy-intensive industry, domestic increases in electricity prices could affect the industry's competitiveness. Energy costs in U.S. aluminum smelting are compared to aluminum smelting energy costs in the rest-of-the-world. Governmental policies affecting these energy costs are discussed.

Jan 1, 1988

By John A. Breslin

This publication provides an historical overview of research undertaken by the U.S. federal government over the last 100 years to improve the health and safety of our nation?s miners. Federal research efforts began with the establishment of the U.S. Bureau of Mines (USBM, or the Bureau) in 1910. They have continued over the past century, even after the Bureau?s closure in 1996. It is hoped that this publication will give the reader an appreciation for the work of mining health and safety researchers over the past century, and of the miners served by this research. Although not a comprehensive history, this report highlights the key organizational changes made within the Bureau and the federal government that affected mining safety and health research. Some mention is also made of Bureau research not directly related to mining health and safety. Note that the work classified as safety and health research has varied over the last century. For example, before 1970 the Bureau separated mining research and safety and health research. At that time, mining research included ground control and methane drainage because they had direct implications for mine safety. Explosives research was also reported separately from health and safety, even though permissible explosives research was obviously related to safety. Therefore, where budget figures from the Bureau are mentioned in this report, it is often not possible to separate safety and health research from other types of research. This history is generally chronological, with a few exceptions. Because of their prominence and direct links to Bureau research, most of the Public Health Service mining studies completed before 1970, when NIOSH was established, will be discussed in a single section, even though the work spanned many decades. Likewise, for convenience, the brief histories of the Bureau?s mining research centers are located in one section.

Feb 1, 2010

By D. A. Larson

The Bureau of Mines conducted research to develop preliminary engineering data necessary if the cobalt-rich manganese crusts that occur in the Exclusive Economic Zone (EEZ) of the Hawaiian Archipelago are to be mined. The research was divided into the following sections: (1) physical, mineralogical, and chemical descriptions; (2) mechanical property testing, such as compressive strength, tensile strength, and a rippability index; and (3) mechanical cutting characteristics, including average and peak cutter forces, the specific energy, and cuttings size distribution. Section 1 utilized microscope, X-ray powder diffractometer, and electron microprobe analyses. Section 2 utilized standard mechanical property testing techniques. Section 3 utilized a converted planer mill with full-size coal cutters to fragment the crust and substrate samples. The manganese crust samples were mainly manganese and iron oxides and hydroxides with an average cobalt content of 1 pct and had a nucleus or substrate of rock or sediment. The significant results shown by the mechanical property and cutting tests are that the crust and all but two types of substrates (basalt and trachyte) are weak materials and easily cut with standard drag cutters. The crusts are generally comparable to medium hard coal in strength and in their resistance to cutting.

Jan 1, 1987

By R. L. Benner

A compound stability diagram was constructed by the Bureau of Mines for the Zn-Fe-S-O system to show the phases that should be thermodynamically stable at various temperatures, oxygen pressures, and SO2 pressures. The diagram was demonstrated to have good qualitative value for predicting stable phases that may, in turn, be related to the recovery of zinc in the leaching phase of the electrolytic zinc process. The study showed that roasting temperature is the most Significant variable in preventing roaster formation of zinc ferrite, which is directly related to subsequent extraction of zinc in the leaching step.

Jan 1, 1966

By Thomas M. Barczak

Wood cribs are used extensively by the mining industry to stabilize mine openings. While the cost per crib is relatively low, their extensive use can result in annual mine costs of over $1 million. In an effort to improve the utilization of these supports and to reduce ground control hazards, the U.S. Bureau of Mines has developed engineering methods to assist mine operators in wood-crib design and employment. Design and employment criteria are established based on the strength, stiffness, and stability of the crib structure in relation to the load conditions imposed by the mine environment. Models have been developed based on full-scale tests in the USBM's Mine Roof Simulator that compute the capacity of wood cribs of various configurations and material constructions as a function of displacement of the crib structure due to roof-and-floor convergence. These models permit the comparison of the loading characteristics and costs of employment of different crib designs, and in conjunction with roof behavior models, provide a means to determine the optimum design and employment strategy.

Jan 1, 1993

By W. W. Graff

This paper describing the mining practices at Mine, No. 4 on the Marquette range, Michigan, is one of a series of articles on mining methods and practices in various mining districts in the United States. Mire No. 4 is located in the Swanzy district, in the southern end of the Marquette range, about 3 miles from Gwinn, Mich. The Swanzy district is an isolated ore-bearing formation, and Mine No. 4 is at the extreme southeastern end.

Jan 1, 1930

By Uldis Jansons

This report evaluates the economic Mining feasibility of four selected mineral deposit types that can be anticipated to be found in (d)(2) lands in the western Brooks Range, Alaska. The major assumption made for this study is the availability of a rail system for transporting equipment and concentrates for the base metal mines. Commodity prices used are those in existence in July 1976. Mine models were established based on known deposits and then evaluated. A lead-zinc-silver-barite deposit for which grades were available but ore reserves were assumed would require approximately 25% higher ore grades or higher metal prices to yield a 15% discounted cash-flow rate of return an the investment if mined at a rate of 10,000 tons per day open pit methods. Large copper-zinc mineral deposits could be mined economically at rates either of 5,000 tons per day underground or 10,000 tons per day by open pit methods. A high-grade copper deposit require a copper price of over one dollar ryes pound to yield an economic profit to be mined at 2,000 tons per day by underground methods. A small high-grade gold underground mine would require a gold price of about $295 per ounce to yield a 20% discounted cash-flow rate of return on investment if all new mine equipment were used and if existing labor rates were paid: Enterprising mining groups operating as partnerships might be able to operate this mine profitably at a gold price of about $152 per ounce, perhaps slightly less.

Jan 1, 2012

By J. M. Mutmansky, C. Lee

"This paper outlines some of the work associated with a research study into the relationship between the characteristics of coal mine dust and the incidence of coal workers' pneumoconiosis (CWP). The project involves study of the chemical, mineralogical, and morphological characteristics of the dust. Early stages of the study have dealt primarily with the size analysis and elemental composition of airborne dust in continuous miner sections. This paper outlines the procedures and findings of the elemental analysis portion of the study.Most of the previous elemental analyses of coal were made available in the quest for information on the combustibility of coal dust or on causal agents and prevalence of CWP. However, no extensive studies have been performed to date, primarily due to the limitations of the analytical methods. A review of the analytical methods for elemental characterization of coal and coal dust particles is presented. TI1e comparisons are made based on the sample mass required, the sample preparation required, the destructivity of the test, and the capability of providing an easy multi-element analysis. The reasons for selecting the proton-induced x-ray emission spectroscopy (PIXE) method are outlined.The PIXE method was applied to both the airborne coal mine dust and channel samples collected from seven continuous miner sections in six different mines. Channel samples of the coal, roof and floor were collected and analyzed. Airborne dust sampling was performed using multi-stage cascade impactors and permissible 2.0 I/min pumps. Sampler locations were fixed in the sections with respect to the continuous miner and roof bolter or with respect to the intake and return airways. Sampling times varied from 45 minutes to 6 hours, depending on the dust concentration.The statistical analysis of the resulting elemental data is presented. Of particular importance are the analyses of the variation of elemental composition with size and the variation in elemental composition over the working section. One interesting finding is outlined showing the multivariate statistical analysis of the trace elements and its implications in the identification of the dust sources. The paper concludes with an analysis of the ramifications of the elemental data to related medical studies."

Mar 1, 1989

By George H. Holmes

This paper is one of a series being prepared by the Minerals Division of the Bureau of Mines on mining and milling methods and practices at various mines in the United States. It describes such methods at the Caselton mine of the Combined Metals Reduction Co. The Caselton mine and mill are in secs. 28 and 29, T. 1 N., R. 67 E., M. D. B. & M., Lincoln County, Nev., about 10 miles by paved highway south- west of Pioche, Nev. (fig. 1). the history of the district and company This circular summarizos operations, describes physical features, labor and living conditions, the geology, ore deposits, and the ore. Prospecting and exploration methods are outlined, and shaft sinking, drifting and crosscutting, and raising are covered under development methods. In the soction on mining mothods, stoping and slushing are discussed, following which are descriptions of underground transportation, hoisting, ventilation, drainage and sampling, and surveying. The surface and crushing plants are described, and milling practices are presented in dotail with explanation of the filter plant and assay office. Safoty practices and the company organization are described in the concluding sections of the circular.

Nov 1, 1950

By W. A. Young

Vermiculite deposits on the. Platt ranch, 12 miles southeast of Encampment Carbon County, Wyo., were investigated by the Bureau of Mines early in 1949. Major activity was centered on property held under lease by the Mikolite Mining & Development Co. (figs. 1 and 2). Vermiculite occurs in masses and lenses of varying size and as disseminations in altered hornblende diorite. Alteration of the host rock probably resulted from the proximity of dikes and irregular masses of pegmatite. Investigation of the Mikolite property consisted of surface trenching, diamond drilling, and sampling. Four trenches totaling 5,401 linear feet were excavated with a bulldozer and Diesel power shovel. Three diamond-drill holes totaling 600 feet were drilled from the surface to determine the character of mineralization at depth. Eighty-one bulk samples were obtained from the trenches, and 130 sludge samples were collected from the drill holes. Samples were analyzed, and ore-dressing tests were made in the Bureau of Mines laboratories at Salt Lake City.

Jan 1, 1952

By Charles Vaught, Richard S. Fowkes, Ronald S. Conti, Barbara Fotta, William J. Wiehagen

The purpose of this study was to determine mine workers' state of fire-fighting preparedness and the technology being used to detect and respond to underground coal mine fires. To investigate this problem, 214 underground coal miners were interviewed by U.S. Bureau of Mines researchers. Frequency distributions of workers ' responses are presented in this report, along with segments of narrative accounts, to profile miners' fire-fighting capabilities. The data indicated that much variability exists from mine to mine and that there are several important changes operators may undertake in order to make miners better prepared to deal with fire underground: select appropriate sensors, establish and test a warning and communication protocol, construct a system capable of delivering hundreds of gallons of water per minute for sustained periods, institute formal fire preparedness audits, develop case studies of events that occur at an operation to use as teaching and assessment tools, and provide structured practice that can be incorporated into fire drills.

Jan 1, 1995

By John W. Buch

Hydraulic cutting tests made on samples of Pennsylvania anthracite (3,700 psi and 260 gpm) were promising enough for the Bureau to establish a full scale experiment in an anthracite mine. Water pressure and quantity for mining anthracite were arbitrarily established at 5,000 psi and 300 gpm (1,000 hp). For full-volume flow, hydraulic pressure is controlled by orifice size with the displacement pump. The hydraulic jumbo was designed for maneuvering on pitches from 0° to 20° in any direction and for a coalbed ranging in thickness from 10 feet 6 inches to 15 feet. All motions of the jumbo are by oil hydraulics. Jet flow is controlled (start-stop) at the face, through an interlocked pushbutton system. One button is in the operator's cab; one, at the pump station; and one (a safety shutoff), near the mining face. To December 1962, 7,400 tons of bed material had been mined at an average rate of 0.800 ton per minute, with an average power requirement of 14.125 kilowatt-hours per ton. In January 1963, the objective was changed from an engineering-development basis to a research basis--to determine, ultimately, the most efficient level of operating characteristics for maximum response, as measured by mining-out rate. This research phase of the project is not yet complete, but conclusions, and the method of arriving at them, will be made the subject of another Bureau publication. It should be noted that as of December 1963 nearly 13,000 tons of bed material had been mined, at rates as high as 1. 3 tons per minute for a complete face advance.

Jan 1, 1965

By E. L. Garton

An active list of permissible explosives was published in July, 1931, as part of United States Bureau of Mines Report of Investigations 3134, under the title of "Active List of Permissible Explosives and Blasting Devices Approved Prior to June 30, 1931." Changes in that list were authorized in August, September, October, November, and December, 1931, and January and March, 1932, as published in Reports of Investigations 3140, 3147, 3150, 3155, 3158, 3161, and 3163, respectively. By these changes the following explosives were added to the active Permissible list: Austin Red Diamond No. 1, L. F. Gel-Coalite W, L. F;" Austin Red Diamond No: 5. Gen-Gel No. 2. Black Diamond Nu-Gel No. 1 Genite C-1 Burton 1, L. F. Liberty No 4 Burton 2, L. F. Liberty No. 5 Burton 10, L. F. Peerless D Burton 12, L. F. Permigel 1, L. F. Burton F, L. F.

Jan 1, 1932

By J. K. Whyatt

The U.S. Bureau of Mines conducted an overcore stress measurement on the 5300 level of the Lucky Friday Mine, Mullan, ID, to investigate the stress regime around an experimental stope in a rock-burst-prone mine. The result indicated a stress field with unexpected magnitude and orientation [s 1 ?135 MPa (19,600 psi) oriented S 80° W). An unusual amount of rock-burst activity was encountered during subsequent excavation. A careful review of the overcore data suggested the overcore strain measurements were valid. Moreover, concentrated rock-burst activity suggested that the measured stress field did exist, but was localized and therefore did not represent the far-field in situ stress field.

Jan 1, 2010

This Part describes a mine pager phone to public telephone interconnect sys tem that permits mine paging telephones to be selectively interconnected with the public telephone system, as illustrated by Figure 1. This interconnect concept was first conceived and demonstrated in breadboard form by H. E. Parkinson of Industrial Hazards and Communications, PMSRC, as one means for providing improved emergency and off-hours communications. The third-generation prototype unit described in this Part was designed and fabricated by Arthur D. Little, Inc. This unit is a small desk-top or wall-mounted unit that connects directly to both the public telephone line and the mine pager phone line, and requires no modifications to either the public dial telephone or mine pager phones. As part of this task, ADL also built, under a very compressed time schedule, a second-generation prototype unit suitable for reliable demonstration of the interconnect concept during the Bureau's technology transfer seminar on mine communications in March 1973. * A major objective of the design of the third-generation unit described in this Part was that it be compatible with present mine pager phone systems utilizing DC voltage on the mine phone line to activate the phone loudspeakers. Therefore, this unit was designed to operate in a push- to-talk, push-to-listen mode that accommodates the inherent design differences and operation modes of the mine phones of different manufacturers. Though this push- to- talk, push- to-listen mode of operation may seem slightly unusual at first sight, we have found it is easily learned by new users. However, mine phone manufacturers wishing to expand their product lines with such an interconnect system will probably find it to their advantage to customize the design of this system to their particular mine phones, thereby utilizing the unique attributes offered by their individual product lines. This customization should not be difficult, and Section III below suggests some of the features that can be easily added to future designs. Detailed parts lists and circuit schematics for the present third-generation proto- type system can be obtained from the system manual submitted to PMSRC and placed on public file.

Jan 1, 1974

By Stephen A. Hare, O&apos

Powder metallurgy processing of commercial Raney nickel powders was examined. The typical angular particle shape, in conjuction with aluminum present in a eutectic phase, facilitated interlocking leading to excellent green strength after compaction. Density and porosity as influenced by the compacting pressure were studied over the range of 37.5 to 207 meganewton per square meter (MN/m2). Sintering in an inert atmosphere from 575° to 850° C caused a volume increase which is attributed to a solid state reaction between Al and Ni2Al3 phases. The reaction is 3Al + Ni2Al3 ? 2NiA13. A thermal pretreatment of 70 hours at 700° C was required to prevent this reaction from occurring during sintering. Density and porosity as a function of compacting pressure and sintering temperature were determined after a thermal pretreatment of the powder.

Jan 1, 1976