Search Documents

By J. B. Salsman

As part of the research effort on investigating the effects of microwave energy on the chemical and physical properties of minerals and ores, the U.S. Bureau of Mines (USBM) Tuscaloosa Research Center has conducted research to measure the dielectric properties of these materials. The objective was to establish a reliable database for use in predicting the effects of microwave heating on a wide range of minerals. The dielectric constants and loss factors of minerals, commonly referred to as the dielectric properties, were determined utilizing the theory of microwave propagation through an open-ended, air-filled coaxial line that was terminated at its open end with the particular mineral under investigation. In this phase of microwave research, the USBM measured the dielectric properties of powdered minerals with medium to high electrical conductivities in the frequency range of 300 MHz to 3 GHz and as a function of temperature from 25 to 325 °C. Since the minerals were prepared as powders, techniques were used to relate the measured dielectric properties of the powdered minerals to the dielectric properties of the mineral at its theoretical or natural density.

Jan 1, 2010

By James Paone

The Bureau of Mines studied the behavior of rocks at the initial state of crater formation that results from the stresses created under a drill bit to determine which mechanical properties of rock are important in rock fragmentation by drilling. Although a definite relation between the drilling strength and relevant mechanical properties has not been established, maximum yield strength of rock is apparently a parameter of drillability of rock. The strengths of rock were considered from the Mohr-Coulomb criterion from which the surface of failure was constructed. The results from previous tri-axial tests on Solenhofen limestone were adopted to verify the criterion of failure. Inelastic behavior of some rock types was observed under a low-velocity impact of a hemispherical bit and under static indentation with a similar bit. Quantitative determinations of strengths of Solenhofen limestone) Indiana limestone, and Tennessee marble were made under static indentation. The maximum yield strength estimated from the average stress over the indented area was used as the crushing strength of rock under a drill bit.

Jan 1, 1966

By Richard V. Ageton

Compressed- air blowers are frequently used both in large and small metal ines , not only as an aid to ventilation , but in some mines as a substitute for an dequate ventilation system . As a temporary fixture , blowers have their uses , but hey should never be used in lieu of a permanent ventilation system. A number Probably the most common error made in placing dependence on compressed- air lowers as an aid to underground ventilation is the tendency to over- rate their cooling efficiency . It is a very common but natural error to assume that compressed air which issues freely from a blower is of the same temperature as the compressed air which issues freely from the exhaust port of a rock-drilling machine . of readings were taken in different mines of the temperature of the rock- drill exhaust , of the compressed air flowing from the blowers , and of the surrounding air In both cases . In general , the temperature of the rock- drill exhaust was from 10 to 30 degrees below that of the surrounding air , in many instances being slightly below freezing , 32° F . The average temperature for a number of compressed-air lowers and for the mine air surrounding them is shown in Table I.

Jan 1, 1922

By K. E. Tame

The Bureau of Mines is studying possible modifications in conventional ore-processing methods that will confine and permit controlled disposal of radioactive liquid wastes. Stream and ground water pollution from radio-active nuclides, principally radium 226 and thorium 230, in liquid wastes from uranium mills can be minimized by reusing the waste solution within the mill. Such reuse of waste solution in an acid leach-resin-in-pulp flowsheet was investigated in the laboratory. The process consists of acid leaching for dissolution of the uranium, sand-slime separation and countercurrent decantation washing for recovery of a pregnant slime slurry, and the use of ion-exchange resin for recovery of uranium from the slurry. Reuse of clarified barren effluent for washing in the simulated mill circuit was carried through 55 cycles. Dissolution of uranium from the ore averaged 97.5 percent. Washing efficiency of 99.9 percent was attained when using 4.35 volume tons4 of combined barren effluent and makeup water per ton of ore. Absorption of uranium from the pregnant slime slurry by an ion-exchange resin averaged over 99.9 percent.

Jan 1, 1962

By Foster Fraas

The objective of this research was separation of one highly conductive mineral from a second conductive mineral , a procedure which is impractical in commercial electrostatic separators using metal rolls . Such separators permit separation of nonconductive from conductive minerals . A new technique involved use of carrier electrode rolls specially prepared by anodizing and / or oxidizing at high temperatures to form suitable oxide surfaces . Specific oxides included aluminum , copper , and nickel . The significant result provided by the new surfaces was the extension of the separation range to higher conductivities , an extension in relative mineral conductivity from 10-14 mhos . The results are in accordance with the blocking- layer theory .

Jan 1, 1964

By R. E. Morgan

Two sizes of Pennsylvania anthracite were gasified in the new-type Lurgi pressure generator at the Dorsten, Germany, works of the Steinkohlengas, A. G. These tests demonstrated that Chestnut-size anthracite and a Rice-Buckwheat mixture containing 27 and 19 percent ash, respectively, could be gasified satisfactorily at an elevated pressure in a fixed bed with oxygen and steam. These coals were especially prepared to approximate a rough-cleaned coal and a washed and screened product. The operating data obtained from the two tests and materials requirements are summarized. A wide range of reactant ratios could not be tested, nor could optimum operating conditions be determined, as the generator was being used throughout the testing program, employing normal operating practices, to produce gas for the gas grid; and the most economical coal, steam, and oxygen ratios may not have been used. Comparative costs are presented of the raw materials required for producing a high-B.t.u. gas, based on the operational data obtained from these tests and, to some extent, on data extrapolated from laboratory experimentation. A flowsheet of a proposed process for producing a high-B.t.u. gas by Lurgi gasification, followed by methanation, is also included.

Jan 1, 1958

In 1962 and 1963, two in situ combustion pilot tests were conducted in the shallow Second Venango sand near Reno, Pa. Because of poor oxygen utilization and lack of production response, both tests were considered failures and were terminated. The area was then relatively inactive until late 1966, when a development well drilled near the 1963 test site had surprisingly good production in what was considered to be a pressure-depleted reservoir. Other wells drilled in and around the old thermal pilot areas also came in as good oil producers. This report presents a study of the increased oil production from the Second Venango sand in the Reno area, and the apparent connection of the present production response and the old thermal pilot tests. Apparently combustion occurred in the Second Venango sand after the 1962 and 1963 experiments were terminated and, supported by large volumes of air left in the reservoir after the 1963 test, generated carbon dioxide which helped repressure the formation. This field evidence of combustion warrants another pilot experiment to further explore the use of properly designed in situ combustion techniques in increasing production from the Second Venango sand.

Jan 1, 1971

By John J. Henn

As part of the U.S. Department of the Interior programs on rutile, authorized by the Office of Emergency Preparedness in June 1967 under provisions of the Defense Production Act, the Bureau of Mines reviewed available literature on major proposed processes for producing rutile substitutes. The processes are grouped according to the major processing step, and important operating features are described. Sixty-one references are cited.

Jan 1, 1970

By S. C. Termes

The Bureau of Mines has used Fourier transform infrared spectroscopy (FT-1R) to study in situ reactions of aqueous solutions of potassium ethylxanthate with CU(II)-and Pb(II)-activated sphalerite plates, in which the plates were both the infrared-transparent windows and the reacting surfaces. A copper (I) ethylxanthate formed predominantly with Cu(II)-activated sphalerite, regardless of the activation time. The products formed on Pb(II)-activated sphalerite depended on the activation times; a short activation time (30 min) yielded a lead ethylxanthate-like product, but a long activation time (90 min) yielded a considerable amount of dixanthogen.

Jan 1, 1986

By C. K. Eilerts

Knowledge of the phase relations of the fluids that exist in the porous spaces of rocks constituting natural petroleum reservoirs and of the behavior of these fluids under various field conditions of operation is essential to the conservation of petroleum and natural gas and to their efficient recovery. The problem of determining whether these fluids axe in the liquid or gaseous state send of recognizing the transitions that may take place as the material in the reservoir is subjected to different conditions of pressure and temperature confronts many producers today, especially in certain fields. The subject has grown rapidly in importance since the discovery of and production from deeper reservoirs that have correspondingly higher pressures rind temperatures as compared with shallower

Jan 1, 1938

By L. K. Weaver

The purposes of this Bureau of Mines report are to review the history of the domestic offshore hydrocarbon production; to project offshore oil and lease condensate production from 1971 through 1985; and to show the impact of offshore development on the onshore segment of the petroleum industry. Since 1954, offshore production has provided an increasingly larger portion of the domestic oil production. Domestic offshore oil and lease condensate production has increased from about 2.0 pct of the U.S. total in 1954 to 16.7 pct in 1970. Likewise, marketed gas production has increased from 1.0 pct of the U.S. total in 1954 to 15.0 pct in 1970. The past performance of exploration, leasing, development, and production of the offshore petroleum industry was used to make projections of offshore oil production. A comparison between onshore and offshore operations was also made. Assuming a tentative Department of the Interior offshore leasing schedule is completed by 1980, the authors estimate that by 1985, about 30 pct of domestic crude oil and lease condensate production from the lower 48 States will come from offshore areas. Currently, leasing of Federal offshore areas has been delayed due to environmental considerations. The rate at which off-shore hydrocarbons will enter the energy market will depend, to a large extent, on how soon environmental considerations are resolved. Assuming that offshore leasing will resume in the near future, U.S. offshore production of crude oil and lease condensate should be about 934 million barrels in 1985.

Jan 1, 1973

By Jos. R. Guiteras

This is one of a series of information circulars describing mining and milling methods being published by the Bureau of Mines. The Summitville Consolidated Mines, Inc., is the only company now active at Summitville. Since the holdings of the company include those of most of the former producers of the camp, the paper virtually becomes a description of the Summitville district. The field data were collected from August 23 to 28, 1937. ACKNOWLEDGMENTS The writer gratefully acknowledges his indebtedness to H. F. Detrick, president, and Edward Thornton, general manager of the company for their cooperation in making this paper possible. Most of the information on underground operations was given by Roy Jellison, mine superintendent; the metallurgical data were supplied by Art Carl son, metallurgist, and W. L. Anderson, mill superintendent; much general and technical information was supplied by J. H. Hannan, engineer.

Jan 1, 1938

By Edward L. McHugh

The appraisal of mineral resources of the Challis National Forest, Idaho, by the U.S. Bureau of Mines, was made so that the mineral resources of the forest could be appropiately considered in land use planning. Information from this study is intended to tip the U.S. Forest Service to incorporate mineral resource data into forest plans The study was done in conjunction with the U.S. Geological Survey, which released a companion report on the geology and mineral potential of the Challis National Forest in 1989. This summary report is derived from a more detailed USBM Open-File Report (MLA 6-91) that includes descriptions of mines and prospects, commodity profiles, and development cost models. Since the 1860's mines within the Challis National Forest have produced mineral commodities worth more than $590 million at current (1989) commodity prices. Identified mineral resources have a gross value of about $2 billion at current prices, including 8 strategic or critical minerals. The U.S. Bureau of Mines study identified and described 723 active and inactive mineral properties within the forest. Mineral properties with identified resources were evaluate to determine their economic significance, and an assessment was made of the feasibility of mineral development. Of the 2,516,191 acres in the Challis National Forest, about 390,000 acres were classified as having mining development interest. Commercially important mineral production, mainly of molybdenum, gold, and silver from the Challis National Forest is likely for the foreseeable future.

Jan 1, 1991

By David C. Grant

In situ uranium mining offers the advantages of minimal environmental disturbance, low capital and operating costs, and reduced mining development time. It is becoming an increasingly attractive mining method for the recovery of uranium from secondary ore deposits. In order to better understand the process, a laboratory technique was developed and used to study and simulate both the chemical and physical phenomena occurring in ore bodies during in situ leaching. The laboratory simulation technique has been used to determine effects of leaching variables on permeability uranium recovery, and post-leach aquifer restoration. This report describes the simulation system and testing procedure in sufficient detail to allow the construction of the system, and to perform the desired leaching tests. With construction of such a system, in situ leaching of a given ore using various leach conditions can be evaluated relatively rapidly in the laboratory. Not only could optimum leach conditions be selected for existing ore bodies, but also exploitation of new ore bodies could be accelerated.

Jan 1, 1985

By V. A. Nieberlein

The purpose of this investigation is to determine the reserves of columbium (niobium) minerals in Arkansas and to develop metallurgical methods for concentrating the minerals and extracting the metal. The columbium resources of central Arkansas were explored by drilling and trenching, and a number of samples were taken. On the basis of this exploration the known reserves of the metal were estimated to be over 78,000,000 pounds. The reserves could possibly be extended by additional exploration to 150,000,000 pounds.

Jan 1, 1954

By Philip C. Good

Preliminary studies showed that direct hydrolysis of H2SiF6 to SiO2 and HF at elevated temperatures was subject to many mechanical difficulties, and that corrosion of construction materials was a serious problem. Elimination of SiO2 from the HF product was generally poor. An alternative procedure, hydrolysis of lime-neutralized H2SiF6 by steam at 950° to 1,100° C, yielded a product very low in SiO2. Condensates containing up to 300 g/1 HF were prepared.

Jan 1, 1968

By Robert L. Lagace

The purpose of the work reported herein was to investigate whether available telephone multiplexing equipment offered a means to rapidly upgrade the traffic-handling capacity of present mine telephone systems and provide for selective calling for safer and more efficient mine operation. Common sense was used to decide whether or not an item could be termed "available." Since conventional telephone gear is not designed to interface pager phones for example, existing shelf items would require adapters to compatibly interface these two types of gear for independent operation over the present single twisted pair used in mines. These and similar small items were allowed, but if a system required any extensive design work to adapt it for the mines, we ruled it "not available."

Jan 1, 1975

By T. R. Jolley

This publication describes the control of fires in inactive coal deposits in the Western United States, including Alaska by the Bureau of Mines. Material presented should contribute to a better understanding of the purpose, process, and benefits of the program. Forty fires were extinguished or controlled in the Western United States and Alaska from 1948 to 1958 under a national program directed by the Bureau's Health and Safety activity. Thirty-five fires were controlled by smothering; three were controlled by the isolation method; and two were extinguished by removing the burning coal, smothering it with incombustible material, and backfilling the fire zone. The fire-control projects were distributed as follows: Alaska 2, Arizona 1, Colorado 9, Montana 9, New Mexico 4, Utah 2, and Wyoming 13. The total cost of the 40 fires extinguished or controlled was $1,203,957. Of this cost, 12.8 percent was engineering and administrative and 87.2 percent was contractual services.

Jan 1, 1959

By R. F. Abernethy

Recent investigations in the United States and in other countries have produced considerable information on the nature and occurrence of minor elements in coal. The possibility of recovering certain elements, particularly germanium and uranium, from coal ash and other coal products has received considerable attention. Some flue dusts are potential sources of germanium, and certain lignite deposits are potential sources of uranium, but industrial recovery of these elements has been limited to small quantities for technical and economic reasons. Considering the large amount of coal mined annually, a small percentage of a rare element may have industrial significance if an economical method of recovery can be developed. In 1944 information on the occurrence of rare elements in coal was reviewed in Bureau of Mines Technical Paper 669 (46).3 This report is a revision of that paper with the view of summarizing published information available for United States coals, and pertinent information concerning coals of other countries. Selected references from the original paper are retained. New references do not include all preliminary reports when more permanent literature describing complete projects is available. Consequently, the list of references should not be considered complete.

Jan 1, 1963

By G. E. McElroy

When mechanical ventilation is to supersede the natural ventilation of a mine it is desirable to determine what resistance the mine as a whole offers to the flow of air in order to specify properly the limiting duties of a ventilating fan. The relation of pressure to volume of flow for the mine as a whole may be calculated from experimental data, or it may be determined directly by measurements of volume of flow and the natural draft pressures causing flow; but in both methods the determinations are affected by many variables. With the intention of making a practical application of both methods, a small metal mine in process of development at Butte, Mont., was selected by the writers as the object of experiments planned to compare the mine resistances determined by measurements of natural draft and volume of flow with those calculated from experimental data. Four sets of teats were made with natural draft in October, 1925, December, 1925, April, .1926, and September to December, 1926; the last set consisted of a series of weekly observations. DESCRIPTION OF MINE The mine selected for the experiments was a typical vertical shaft metal mine in the development stage. No stoping had been done, and ventilation was confined to shafts, crosscuts, drifts, and raises. Figure 1 is a dia¬grammatic sketch of the main openings. All were timbered with full sets on approximately 5-foot centers. The shaft compartments were 4 by 4.5 feet, and one in each shaft was partly blocked by staggered manway landings. A pump column in the upcast shaft was discharging about 280 gallons a minute of water at 70° F. from the 1,000-foot level. The drifts were slightly sinuous, but the crosscuts were exceptionally straight and uniform in area; both drifts and crosscuts were about 5 by 7 feet in cross section. The raises were composed of vertical sections joined by frequent 450 offsets; each had three 4.5 by 4.5-foot compartments, of which two were plank-lined ore chutes and one was partly

Jan 1, 1928