Search Documents

By H. C. Fuller

A method was devised and developed by the Bureau of Mines for decomposing manganese sulfate at significantly lower temperature than that required by the conventional procedure of using heat alone. This technique, called the partial reduction method, effected decomposition at 700° to 800° C, as compared to 900° 1,000° C normally required. The process consisted of heating, in the absence of oxygen, a mixture of manganese sulfate and a controlled quantity of a reducing agent. The suitability of commercial-type equipment was tested in laboratory-size models of an externally heated rotary kiln, a r bbled muffle-hearth furnace, and a fluidized-bed reactor. The rabbled-hearth furnace gave the best results with the least operating difficulty produced a gas containing more than 80 percent SC and eliminated 96 percent of the sulfur when coal was used as the reductant. Sintering of the powdery decomposition product produced an agglomerate containing, in percent, 63.6 Mn and 0.4 S.

Jan 1, 1966

By Thomas W. Camm

In this U.S. Bureau of Mines report, mine and mill cost models are presented to make quick estimates of the cost to develop mineral deposits in the desert region of the Southwest United States. Regression analysis was used to generate capital and operating cost equations for each model in the form Y = AXB, where Y is the cost estimated and X is the assumed daily capacity in short tons. A and B are constants determined by the regression analysis. Each is broken down into 11 subcategories to facilitate escalation of costs for inflation and to increase their versatility in economic evaluation work. This report contains 2 open pit models, 6 underground mine models, 11 mill models, and cost equations for access roads, powerlines, and tailings ponds. In addition, adjustment factors for variation in haulage distances are provided for open pit models and variation in mining depths for underground models.

Jan 1, 1991

By Stephan Stecura

One of the principal objectives of the Bureau of Mines program for development of superrefractory ceramic materials is to obtain fundamental data on the physical properties of refractory oxides. Elements of particular interest to research workers in the Bureau include groups III and IV of the Periodic Table and the rare-earth group. This report contains thermal expansion and phase inversion measurements on oxides of scandium, yttrium, lanthanum and 12 lanthanide series elements (promethium and terbium omitted) up to 1,350°C, made by high-temperature X-ray diffractometer techniques. Thermal expansion values were calculated from unit cell dimensions measured at selected temperatures; with anisotropic oxides expansion was determined parallel to each major crystallographic axis. The combined random and systematic errors in the thermal expansion values are considered to be less than 3 percent of the total expansion at 500° C, and approximately 2 percent at 1,000° C, No difference in expansion coefficients was observed between heating and cooling cycles for oxides that did not undergo phase inversion. Tabular data of linear expansion, in percent, linear expansion coefficients, and graphical presentation of linear expansion as a function of temperature are presented.

Jan 1, 1961

By Alfred E. Schwaneke

A new high-temperature soft soldering system has been developed by the Bureau of Mines for use on copper, copper alloys, and low-carbon steel; the method is applicable to automobile radiators and home appliances. The system uses a unique sacrificial metal coating method to promote spontaneous wetting and spreading of zinc and zinc alloy solder: on metallic substrates. The 10-5 to 10-6 cm thick, electroplated or sputtered, sacrificial nickel coating is absorbed by the molten filler alloy during soldering and produces a direct solder-substrate metallic bond. Preliminary measurements on butt joints with copper members give tensile strengths up to 22,000 psi at room temperature using 95 Zn-5 Al alloy as solder. Spontaneous wetting, spreading, and capillary penetration are extremely rapid and produce joints as easily as 50-50 tin-lead solders. Recrystallization or annealing of the wrought copper joint members is negligible at the soldering temperatures of 450° to 490° C and lower. A list of fluxes and solder alloys is included in the report.

Jan 1, 1970

By W. W. Adams, T. D. Lawrence

"The National Safety Competition of 1938, the fourteenth of its kind conducted by the Bureau of Mines in which bronze trophies known as Sentinels of Safety are awarded to winning companies, has just been completed and the results are presented here.With 345 mines and quarries competing, more than in any previous year except 1931, the contest revealed low accident rates at many of the enrolled plants and, which is even more remarkable, it revealed 113 mines and quarries at which no lost-time accidents occurred during the contest year.The Sentinels of Safety trophies, provided by The Explosives Engineer magazine, were awarded to four underground mines, one open-pit mine, and one quarry. Each employee of the winning plant was awarded a Certificate of Honor by the Bureau of Mines in recognition of the employee's part in helping his company to win the trophy. In addition to the award of trophies, a Certificate of Honorable Mention was awarded to each of the mines and quarries in second, third, fourth, and fifth places in their respective contest groups and also to each mine and quarry that worked 30,000 or more man-hours without a lost-time accident. Ninety-two such certificates were awarded for 1938. Twenty-three other mines and quarries also operated without an accident but worked less than 30,000 man-hours, the minimum required by the contest rules for award of Certificates of Honorable Mention.Previous to 1938, five trophies were awarded annually in the National Safety Competition. For the 1938 contest a sixth trophy was provided by The Explosives Engineer so that open-pit mines and quarries, two classes of operations that previously had been included in one group in the competition, might have separate awards."

Aug 1, 1939

By Thomas P. Mucho

Retreat or pillar recovery mining redistributes the overburden weight onto the adjacent coal pillars in a room-and-pillar section. The additional stress and the resultant energy stored in the remaining pillars can become so great that pillars may bump or violently fail. An investigation at the Gary No.2 Mine was conducted to examine the effectiveness of the thin pillar mining method for mitigating bump occurrences. Field observations were made and instruments were installed to monitor pillar behavior during extraction. Stress monitoring instruments and roof-to-floor convergence stations were installed in pillars and entries and crosscuts, respectively. Results indicated that high pillar stress concentrations occurred in these bump-prone geologic conditions. The thin pillar mechanism, the creation and progressive outby movement of an expanded yield zone, was also monitored through the instruments. The expanded yield zone, a result of using thin pillars in a highly stressed pillar line area, mitigates bump risk.

Jan 1, 2010

By Charles M. McCulloch

This Bureau of Mines report discusses the principles of using computers to draw maps and plot geologic data of mining areas. The types of maps that can be drawn by a computer are reviewed, using as examples two separate areas where poor roof and gas emissions caused mining problems. Such maps can be used not only to help identify problem areas, but also to predict areas where problems could occur, thus giving mine operators time to work out solutions prior to mining. The average cost of a computer-drawn map for a mine property is less than $100, including computer time and man-hours for data preparation.

Jan 1, 1976

By T. E. Howard

The western phosphate field, comprising parts of Idaho, Montana, Wyoming, and Utah, contains one of the world's largest known reserves of phosphate rock. Although phosphate-rock deposits of good-grade have been known since before the turn of the century and production has been recorded since 1906, real development of this important field did not begin until immediately after World War II. Since then fertilizer-manufacturing facilities using western phosphate rock have been expanded, and three electric-furnace plants for producing elemental phosphorus have been installed, resulting in a rise in mine production from 323,955 long tons2/ in 1945 to 1,653,916 long tons3/ in 1953. Interest in the field is increasing, and it is reasonable to expect that the western phosphate industry will continue to expand. Before 1945 all western production was from underground mines. In that year the first strip mine in the field was started near Montpelier, Idaho,~ and in sub-sequent years a number of other open-pit mines were opened in southeast Idaho and western Wyoming. At present the major part of the production comes from surface mines. Underground mining has continued, and new underground mines have been opened in the field, but recent exploration by operating companies has been aimed primarily at developing additional deposits suitable for low-cost surface mining. Preliminary reserve estimates by the Federal Geological Survey5/ indicate that only a very small part of the total resource may be recovered by surface methods and that the industry eventually must depend largely on underground mining. Because one function of the Bureau of Mines is promoting the conservation and development of the Nation's mineral resources, it is appropriate that research be conducted to develop low-cost maximum-recovery underground mining methods applicable to western phosphate-rock deposits.

Jan 1, 1956

By J. W. Paul

A superintendent is one who has the oversight and charge of some organiza- tion or enterprise, with porer of direction. The superintendent of a coal mine is the official who is in general charge of conducting the operation of the nine for the purpose of producing coal; he is accountable to his superiors for all matters that relate to the cost of production and safety in operation, ed under him are all the underground officials and other personnel making up the mine organization. The responsibility of the superintendent covers all the principal phases of mining, purchases of materials, issuance of supplies, accounting, and upkeep of the property and equipriont. In a broad sense, the superintendent must view his job as embraced under four gneral heads: (1) Construction, (2) instruction, (3) supervision; and (4) discipline. The degree of efficiency with which each of these phases of his work is conducted is a measure of the safety factor which the superintendent injects into his job. Injury to workmen and damage to property may be due to neglect of one of these general headings; as for example in the collapse of a scaffold there has been faulty construction which may be found upon investigation to have been the result of faulty instruction or lack of instruction. It may be that the condition of the scaffold was not ascertained in advance of its collapse through faulty supervision, or the discipline of the workmen had been neglected.

Sep 1, 1930

By N. E. Hanna

As part of a program for improving, the safety of permissible explosives, the Federal Bureau of Mines has undertaken an investigation to establish the ability of sodium chloride to reduce the incendivity of permissible explosives to firedamp atmospheres. A motivating influence for this investigation has been the comparatively extensive experience of British and other European investigators, who used sodium chloride as a component of their permitted explosives (1, 5, 6 7).5/ In the United States research and development work of this type has been less extensive, although sodium chloride has been added to permissible explosives as a cooling agent (9) for many years. The results of the first phase of this investigation were presented in a previous paper (8), which established that adding up to 10 percent sodium chloride to permissible explosives reduces the likelihood of ignition of firedamp in the gallery test; however, the results were somewhat inconsistent, and the conclusions were qualified. Accordingly, the investigation was continued with a study of the effect of added sodium chloride as a function of the quantity added and of the particle size of the salt.

Jan 1, 1960

By E. R. Bauer

This report presents the results of a cooperative study between BethEnergy Mines Inc., Ebensburg, PA, a central Pennsylvania coal mining company, and the U.S. Bureau of Mines to investigate longwall development entry roof instability. In-mine mapping of geologic and deformational features was conducted to reveal the major ground control problems encountered during gate road development. In addition, mining-induced pillar load monitoring was used to indicate development loading on variously dimensioned gate road pillars and to determine if pillar yielding occurred. Finally, visual observations of a variety of roof control methods were used to determine the most effective support elements for controlling cutter roof failure.

Jan 1, 1992

By William P. Diamond

This report presents results of a cooperative research project between the U.S. Bureau of Mines and BethEnergy Mines, Inc. Four coreholes (two before mining and two after mining) were drilled at a longwall mine operating in the Lower Kittanning Coalbed to obtain coal and rock samples from over-lying strata to determine their gas content at various times in the mining cycle. The results of those tests indicate that 91 pct of the gas removed from the overlying strata came from coalbeds. Material balance calculations were made to compare the volume of gas produced both from gob gas vent holes drilled on the panel and gas removed by the mine's ventilation system with the volume of gas removed from strata directly overlying the panel to a height of 275 ft. This analysis indicates that only 40 pct of the total gas produced from the panel actually came from the strata directly overlying the panel. The remaining volume of gas production probably migrated to the longwall gob from overlying, and perhaps underlying, strata immediately adjacent to the panel and perhaps from greater distances downdip because of the establishment of a long-term pressure gradient in the study area.

Jan 1, 2010

By O. C. Blade

"INTRODUCTION This report on the properties of motor fuels sold through service stations in the United States is a continuation of a series of reports made in accordance with a cooperative agreement between the Coordinating Fuel Research (CFR) Committee of the Coordinating Research Council (CRC) 3/ and the Bureau of Mines of the United States Department of the Interior. The first of these reports presented data on motor gasolines sold during the winter of 1935-36. 4/ Further reports were issued describing motor gasolines sold during the succeeding summers and winters to and including the summer of 1941. 5/ No reports were made on motor gasolines Bold during the winter of 1941-42 and during the summer of 1942. However, starting with the winter of 1942-43, the semiannual reports were resumed. 6/The present report presents analytical data for 1,499 samples, representing the products of approximately 105 companies. As in previous surveys, the companies covered by the survey include both large and small suppliers. Conforming to former reports, the data cover three groups of samples - regular-price, premium price, and third-grade gasolines.As the number of analyses submitted for samples of third-grade gaso¬line are not considered adequate to represent this type of motor fuel, data for these analyses have not been averaged, but the individual items are tabulated. The number of samples, items and brands comprising each group is as follows; Regular-price, 872 samples, 266 items, and 83 brands; -premium-price, 584 samples, 217 items, and 72 brands; third-grade, 43 samples, 32 items, and 21 brands. The meanings of those terms as used in the surveys are as follows:"

Jun 1, 1945

By C. P. Fang, V. A. Marple, K. L. Rubow, P. H. McMurry

"It has been known for some time that sizes of aqueous particles may be affected by flow-induced relative humidity (RH) changes. The RH of air flowing through an impactor decreases as a result of pressure drop through the impactor and increases because of aerodynamic cooling within the high-speed jets, as illustrated in Figure 1. Because the sizes of aqueous particles depend on RH, the impaction stage on which such particles are collected may be different from the stage where they ought to be col¬lected, based on the particle size at the sampler inlet.Fuchs (1980) reviewed literature on water vapor condensation in impactors. The reviewed impactors operated at jet velocities of 100-250 m/s. Particle size increases ow¬ing to water vapor condensation were found in all cases. In one case (Khorguani et al., 1970), it was found that very small droplets (Dp <_ 0.02 um) containing sodium chloride and silver iodide were collected in an impactor with a cut point of 0.32 µm and a jet velocity of 100 m/s. Fuchs believed that such particles could not be captured in an impactor without having been enlarged by condensation. Winkler (1974) sampled at¬mospheric dust with a rectangular nozzle impactor that had a nozzle cross section of 0.3 x 15 mm, a cut size of 0.4 um, and an average jet velocity of 100 m/s. No adhesive was used on the impaction plate. The collection efficiency increased as air humidity was increased from 20% to 100%. The effect was especially noticeable in the increased collection efficiency for hygroscopic particles, and was attributed to condensation.Extensive theoretical and experimental research work on the distortion of the particle size distributions in impactors was done by Biswas and coworkers (1985, 1987). The impactors employed in the study were a low-pressure impactor with high jet velocity stages (Hering et al., 1978, 1979) and a conventional six-stage impactor, Sierra's model 226, operated in the incompressible regime. Ammonium sulfate aerosols were chosen for the study. In the low-pressure impactor, an orifice operating at a Mach number of 1 causes a sudden pressure drop, significantly reducing the RH in the next two stages (stages 5 and 6). This results in a 0.15-um diameter ammonium sulfate droplet shrinking to about 0.07 um at stage 5 when the inlet RH is 95%. In stage 7, the tempera¬ture drop is considerable because the jet speed is sonic. For an inlet RH of 95%, a 0.03 um droplet grows to about 0.06 um. However, the same size droplet at an inlet RH of 25% grows to only 0.04 um. For the Sierra model 226 cascade impactor that is operated with a Mach number of 0.27 at the last stage (stage VI), it was found that for an inlet RH of about 67%, particle growth would occur in stage VI. At 80% RH, both stages V and VI were affected. Biswas et al. (1987) stated that Mach number alone does not determine the size biasing; the type of aerosol, the inlet conditions, the temperature and pressure ratio, and the impactor geometry (throat length, jet-to-plate distance, etc.) must be considered for each stage in evaluating the distortion of the particle size distribution."

Mar 1, 1992

By Ludwig Schmidt

Large quantities of gasoline are lost each year by evaporation from bulk-storage station tanks. The rate of evaporation from bulk-station tanks is influenced by two principal factors: First, the vapor pressure of the gasoline in the tank; and second, the amount of "breathing" of the tank. The vapor pressures of the gasoline govern the amount of the gasoline vapor in the air-vapor mixture above the gasoline in a tank at a given temperature. This is one of the principal factors in determining the total pressure of the air-vapor mixture within the tank. The "breathing" of the tank is caused by the inflow of air from the atmosphere during certain periods of the day and the expulsion of the air-vapor mixtures at other times, caused by atmospheric variations. The pressure built up within a tank and the amount of gasoline in the air-vapor mixture are both a direct function of the temperature existing within the tank. Therefore, two of the most common methods for reducing evaporation losses from bulk-station tanks are: (1) The use of vapor-tight tanks equipped with relief valves and operated at 1 or 2 ounces of pressure and about .5-ounce vacuum; (2) reducing the temperature of tanks and their contents by painting them a light color, by insulation, and in some instances by using water sprays. Water sprays, although effective, usually are too expensive to operate economically. In order to determine and compare the effects of various colors, insulation, and pressure in reducing the evaporation losses of gasoline held in storage in bulk-storage tanks, the Bureau of Mines made observations from May 29 to October 15, 1930, on five horizontal tanks of 12,000-gallon capacity each, which were erected at the plant of Black, Sivalls and Bryson Manufacturing Co., Kansas City, Mo. This report gives in detail the results of these evaporation tests.

Jan 1, 1931

By F. P. Haver

The Bureau of Mines has investigated the electrochemical reduction of lead chloride as a method for producing lead without the pollution problems associated with smelting. It was determined that high-purity metal (>99.9 pct Pb) could be obtained, using PbC12 prepared by ferric chloride leaching of galena concentrate: PbS + 2FeCl3?PbCl2 + 2FeC12 + S°. Optimum results in small-scale electrolytic tests were achieved with a bath consisting of 40 to 70 wt-pct PbCl2 dissolved in KC1-LiCl eutectic, an operating temperature of 450° C, a current density of 2.5 amp/in2, and an electrode spacing of 0.5 inch. In large-scale tests made to develop a cell design for commercial application, the optimum electrode arrangement proved to be a bipolar configuration with horizontal plates. This gave a current efficiency of 86 pct with an energy requirement of 0.52 kwhr/lb lead. To determine the effect of impurity buildup in the bath, 1,200 lb of PbC12 prepared by ferric chloride leaching of galena concentrate was electrolyzed over a period of 2 months. Little deterioration of the metal quality occurred in that time; all of the lead produced had a purity equal to or better than corroding grade (>99.94 pct Pb).

Jan 1, 1976

By F. S. Kendorski

This report covers the work on developing criteria for determining when a hazard exists when mining stratified mineral deposits beneath bodies of surface water. The nature of water bodies is considered, the disturbance to the strata induced by mining is described, inundation case histories reviewed, reasonable water inflows derived, and methods of mining to prevent or minimize the hazard are presented. Criteria are given whereby effected industries and agencies can recognize a potential hazard and plan a mine accordingly, releasing considerable mineral reserves otherwise considered unminable.

Jan 1, 1979

By Paul L. Russell

This property has been examined several times in the last few years , and findings have been reported . In the fall of 1942 , the author supervised sampling both lode and placer deposits . The ore was beneficiated , and the results obtained are incorporated in this report . stia The Morgan Group , which comprises seven unpatented mining claims and the Black Cat placer claims , was purchased by the Manganese Products Corp. from H. D. Hill of Hatch , N. Mex . , and Dr. A. C. White of Hot Springs , N. Mex . Arthur L. McRowe , 876 27th Avenue , San Francisco , is president of the corporation , and David Fewer, 824 Times Building, Long Beach, is treasurer . J. T. Murray is in charge of operations .

Feb 1, 1947

By D. J. Parker, D. Harrington, L. H. Harrison

"INTRODUCTION The necessity for protection against the hazards of lightning manifests itself from time to time in the mining industry by reason of loss of life, damage to electrical equipment, fires in surface structures at mines, and accidents in the handling and use of explosives. This paper is intended to assemble, correlate, and present some of the salient points embodied in the available literature on the subject and at the same time give some factual data concerning instances of such loss of life and damage to property, with special application to the mining industry.The annual loss of life and destruction of property by lightning is considerable; the former may be prevented to a limited extent, though use of common sense as to exposure is required and not always followed; the latter can be prevented to a considerable degree. The manufacturers of electrical equipment, through improved types of lightning arresters, have done much toward the protection of electrical equipment, with consequent safeguarding of life and of property. Education based on unfortunate experiences has gone far to discourage the handling of explosives and blasting accessories during thunder storms, especially in open pits and quarries, and to a much smaller extent in underground workings. The lowly lightning rod plays an important role in the protection of certain types of buildings (especially isolated buildings), stacks, monuments, and other structures.LIGHTNING PHENOMENAIn 1751, Franklin proved that, lightning was simply a visible display of electricity - an extended spark; and until a generation ago little had been added to his exposition to define the various phases of the phenomenon. Matters pertaining to lightning are discussed in the following references:"

Apr 1, 1948

By Carl F. Wingquist

In support of Bureau of Mines studies of thermal fragmentation of rock, the elastic moduli of four types of rock were measured at temperatures ranging from room temperature up to 1,500° F (1,089° K). The sonic method was employed to determine the resonant frequencies of the rock specimens and from these frequencies, the elastic moduli were calculated. Data for Young&apos;s modulus, shear modulus, and Poisson&apos;s ratio are given as a function of temperature for Dresser basalt, Reserve taconite, Jasper quartzite, and Charcoal granite. Young&apos;s modulus and the shear modulus decreased with increasing temperature up to about 1,200° F and then became relatively insensitive to temperatures from 1,200° to 1,500° F.

Jan 1, 1969