Search Documents

By Joseph A. Cavallaro

This report describes the timed release analysis technique that was developed to serve as a tool for assessing the froth flotation cleaning potentials of fine-size coals. Using this developed technique, 16 coals from 10 different coalbeds were tested. All of the coals included in this study were quite amenable to froth flotation with float coal yields ranging from 80.7 to 99.5 percentage points. Float-and-sink analyses of the coals tested are shown to be of limited value in predicting froth flotation cleaning potential. Generally the float-and-sink analyses indicated a better product could be obtained than froth flotation could provide; although, in four of the coals tested froth flotation results were superior to those expected from the gravimetric analysis. The fixed carbon content of the samples collected was found to correlate with the floatability of the coals. The higher rank coals were the most readily floatable coals while the lower rank coals did not respond quite as well to flotation.

Jan 1, 1965

By Norma Golumbic

The primary purpose of the Bergius (hydrogenation of coal) and Fischer-Tropsch (hydrogenation of carbon monoxide) processes is the production of synthetic liquid fuels. This objective is of importance in insuring an adequate supply of motor fuels and lubricating oils in the United States. In the urgency of the basic research and process development work on synthetic liquid fuels, the possibilities for the production of synthetic chemicals inherent in these processes have hitherto received little attention in this country. However, the by-products, as well as the primary products, from the Bergius and Fischer-Tropsch processes are rich source materials for organic chemicals. The overhead oil from liquid-phase hydrogenation of coal, for example, contains benzene, toluene, xylene, cyclohexane, methylcyclohexane, aromatic solvents, about 20 percent tar acids (largely phenol, cresols, and xylenols), and 3 percent nitrogen bases. Wax, alcohols, and acids are by--products of the Fischer-Tropsch synthesis. In addition, techniques have been developed which make possible the production of aliphatic hydrocarbons, alcohols, acids, aldehydes, and other oxygenated organic compounds. These chemicals are more valuable on a unit basis than gasoline. Because of continued rapid expansion of the plastic, resin, lacquer, and solvent industries, larger amounts of many of these chemicals will be needed in the near future.

Jan 1, 1949

By Irving Hartmann

1. Under the conditions of the tests described herein, the proper use of an incombustible stemming plug of the type discussed prevented ignitions of gas in all tests during the firing of 21 single shots of permissible explosive in cool. In two tests with multiple blasting (four and five shots each) no ignitions resulted. 2. The results of a few tests in this investigation and of numerous tests made previously indicate that fire-clay stemming of the same weight as an incombustible plug provides about the same degree of protection as the plug against gas ignitions during blasting of coal by permissible explosives. 3. The hazard of gas ignition on firing charges of non-permissible 40-percent gelatin dynamite in coal was reduced but not eliminated when the shot holes were stemmed with one or two incombustible plugs or with an equivalent weight of fire clay. 4. On the basis of this investigation, the Bureau of Mines considers the proper use of incombustible stemming plugs of the design tested, under the conditions of the tests described in this paper, to be of equivalent safety as the same weight of fire-clay stemming. This report does not constitute approval or disapproval of the incombustible stemming plugs by the Bureau of Mines. 5. The test data indicate that misfired charges in shot holes stemmed with the incombustible stemming plug cannot be disposed of with certainty by the procedure recommended by the manufacturer. In this investigation the misfired charges failed to detonate in 30 percent of the trials.

Jan 1, 1950

By William W. Adams

The stone-quarrying and related industries of the United States made large gains in employment in 1936 over 1935, according to reports furnished by operating companies to the Bureau of Mines, United States Department of the Interior. Not only were more men employed, but also increases were made in the number of man-days of labor performed and in the number of man-hours worked in 1936. The increase in employment, however, was accompanied by an increase in the number of accidental deaths and injuries among the workers and by a slight increase in the accident-frequency rate per million man-hours worked. The fact that the larger number of accidents resulted in only a slight increase in the accident rate is explained by the large gain made in the number of man-hours worked during 1936. The accident rate in 1936, although higher than in 1935, was the lowest and therefore the best that the industry has experienced in any previous year except 1932 since complete and comparable figures first became available in 1916, a period of 21 years. Operators' reports to the Bureau of Mines showed that the industry as a whole employed an average of 80,022 men in 1936 and that the men worked a total of 18,874,254 man-days or 147,064,448 man-hours. Accidents in and about the plants caused 91 deaths and 5,717 nonfatal lost-time injuries among the workers. The number of injuries and deaths represented an accident-frequency rate of 39.5 per million man-hours worked, compared with a rate of 38.2 in 1935.

Jan 1, 1938

By Robert L. Kranz

The U.S. Bureau of Mines (USBM) has been monitoring and studying seismic activity associated with mining in the Coeur d'Alene silver district of northern Idaho. New statistical methods of studying the stope-scale (1-to l00-m) seismicity at one Idaho silver mine are used in this report (part 1) and its companion (part 2). This report deals with methodology and its limitations. The recent concept of fractals and their seismological use is discussed and applied to mining-induced seismicity. Three types of fractal studies are addressed: spatial analyses (including temporal changes of spatial patterns), temporal analyses, and size analyses. Other statistical measures of mine seismicity are also addressed: event mean location, inter-event distance distribution skewness, temporal coefficient of variation, nearest neighbor and next event statistics, and event location planarity patterns. Each of the methodologies discussed (fractal and nonfractal) is presented using sample data from two stopes in the mine. It is shown that stope-scale, mining-associated microseismicity has a fractal nature. The usefulness of demonstrating fractality (scale invariance) for predictive or descriptive purposes depends on recognition of the factors affecting the calculation of fractal dimensions. Several methodological traps are illustrated that can lead to an incorrect conclusion.

Jan 1, 2010

By Theodore L. Turner, Joseph H. Swift

A study on a small laboratory scale was made of the use of ammoniacalammonium carbonate for batch leaching Mn from low- grade manganiferous materials ( 6 to 16 pct Mn) obtained from deposits in the southern district of Aroostook County , Maine . These materials were partially reduced at 500 ° to 700 ° C with H₂ or CO and then leached with solutions of NH and CO₂ dissolved in water . Extraction of 80 to 90 pct of the Mn was obtained from some sample materials , but 10 to 34 pct of the iron was also extracted . Material from the Littleton Ridge deposit contained manganese intimately associated with Fe , a condition which contributed to difficulties in obtaining a commercially acceptable product . Extensive investigations of the leach and reduction processes with various mixtures of H₂ and water vapor , and CO and CO₂ , failed to disclose a set of conditions for selectively leaching the manganese . Finely divided metallic Fe was probably produced during the reduction steps so that Fe was leached with the Mn in the subsequent extractions .

Jan 1, 1964

By F. F. Netzeband

This report relates to the sulfur industry of seven States--Arkansas, Kansas, Louisiana, Mississippi, Missouri, Oklahoma, and Texas--and is part of a national study of the sulfur industry by the Bureau of Mines. Markets as used 1n this report are divided into two components for individual analysis--(1) supplier markets which include regional Frasch and byproduct sulfur producers and (2) consumer markets which include processors and manufacturers requiring sulfur in their operations. The term sulfur as used in this report includes brimstone, native sulfur, elemental sulfur, or sulfur equivalents.

Jan 1, 1964

By C. T. Anderson

In July 1947, the U. S. Bureau of Mines, in cooperation with the Air Materiel Command, started an investigation of zirconium alloys with the object of determining the suitability of such alloys for high-temperature applications. This report covers the preliminary study of about 25 zirconium-rich alloy systems with respect to preparation, fabrication, tensile properties, metallographic structures; constitution, and heat resistance. Obviously, each system could not be investigated thoroughly, and this publication can be regarded only as a first approach. The more promising individual alloy systems will be studied in greater detail and reported in subsequent publications. The study of zirconium alloys on such a scale has been made possible by the U.S. Bureau of Mines developments in the past 5 years On producing zirconium metal. This basic process is similar to that developed by Kroll for producing ductile titanium metal and consists essentially of reducing zirconium chloride by means of molten magnesium. The Northwest Electrodevelopment Laboratory at Albany, Oreg., has produced several thousand pounds of ductile metal in this manner and has a pilot plant producing over 300 pounds of metal per week. Alloys were prepared by melting Bureau of Mines zirconium and the best available grade of alloying element in graphite, with suitable provisions for preventing oxidation. The ingots were quartered longitudinally and sheath-swaged at 850° c. to 3/8-inch diameter rod. Two of those rods were send to Wright Field for room-temperature and 1,200° F. tensile properties. The remaining two sections were used for metallographic, hardness, heat-treatment, and heat-resistance studies. The salient features of this investigation are summarized in table 1.

Jan 1, 1950

By Lowell Stroud

Since 1929, the Helium Activity of the Bureau of Mines has operated a helium-extraction plant at Amarillo, Tex. The natural gas that supplies this plant is obtained from the Cliffside geologic structure 12 miles to the northwest and over the years, has become known simply as "Cliffside gas," There is need for published data on the low-temperature phase equilibria of helium-bearing natural gases. To date, little information has been published on the equilibrium phase compositions, solution of helium in condensed natural gas, condensation characteristics, or equilibrium vaporization coefficients for methane, nitrogen, and helium in helium-containing systems. A windowed phase equilibrium apparatus (8)6 was used to obtain 105 equilibrium samples, representing 35 experimental conditions of condensed Cliffside gas at pressures of 100, 200, 300, 400, and 500 p.s.i.a. and temperatures from 0° to -270° F. Data on equilibrium vapor-liquid composition for Cliffside gas are presented in both tabular and graphic form and are discussed in detail to show their relationship to certain criteria that must be met to effect an efficient separation of helium from natural gas by means of low-temperature processes. Facts about condensation characteristics and solution of helium in the liquid phases are included, The important relationship of these two factors in decreasing the percentage of total helium lost by solution in the liquid phase is discussed.

Jan 1, 1961

By C. W. Davis

This report follows the same general scheme as did its predecessors; it begins with a dissertation on some phase of ore-testing, continues with results of investigations of ore-treatment methods and of metallurgically important analytical processes, and concludes with an exposition of tests made by established methods on typical ores selected as representative of certain mining districts. One of the first things that is done after an ore has been received is to look at it under the microscope. Microscopic examination serves as an important complement to chemical analysis in interpreting the percentage composition in terms of minerals. If it has been found difficult to treat an ore, the reasons for this action and indicated methods to overcome the difficulties may be ascertained by testing with a microscope. For example, failures in selective flotation have been traced to intimate mineral association and changes in mineral surfaces through incipient oxidation. The importance of surface stains or tarnishes and the presence of adhering slime particles have been found to be responsible for the difficulty experienced in the treatment of certain gold ores.

Jan 1, 1938

By C. W. Davis

This report follows the same general scheme as did its predecessors; it begins with a dissertation on some phase of ore-testing, continues with results of investigations of ore-treatment methods and of metallurgically important analytical processes, and concludes with an exposition of tests made by established methods on typical ores selected as representative of certain mining districts. One of the first things that is done after an ore has been received is to look at it under the microscope. Microscopic examination serves as an important complement to chemical analysis in interpreting the percentage composition in terms of minerals. If it has been found difficult to treat an ore, the reasons for this action and indicated methods to overcome the difficulties may be ascertainedd by testing with a microscope. For example, failures in selective flotation have been traced to intimate mineral association and changes in mineral surfaces through incipient oxidation. The importance of surface stains or tarnishes and the presence of adhering slime particles have been found to be responsible for the difficulty experienced in the treatment of certain gold ores.

Jan 1, 1938

By Richard W. Knostman

A study was made of the factors affecting lead and zinc production in the Pacific Northwest. Costs, ore reserves and potential resources, and domestic demand were analyzed. It was concluded that a projected 3.1-percent average annual increase in U.S. demand for zinc through 1975 and a corresponding 2.5-percent rise for lead will be supplied mainly from mines in the Eastern and Central States. Annual Pacific Northwest mine production of lead is estimated to fluctuate around 82,000 tons, while zinc output may average 135,000 tons through 1975. Measured, indicated, and inferred reserves in the Pacific Northwest, containing 1.56 million tons of lead and 2.59 million tons of zinc, are more than sufficient to maintain this level of production. Annual production from Pacific Northwest electrolytic zinc plants is expected to increase to over 300,000 tons of slab zinc by 1975. Lead smelters may experience difficulty in maintaining output at 1964 levels.

Jan 1, 1967

By M. J. Gavin

Within the past three years numerous inquiries for information on oil shale have been received by the Bureau of Manes. These inquiries have been increasing to such an extent that it has seemed advisable to issue a short paper prior to the publication of a bulletin on the subject, giving a, general discussion of the subject and a comprehensive list of references, so that those interested in the details of obtaining oil from shale can find additional information without much difficulty. Some of those who desire information are interested only in a general discussion of the subject, or are not in a position to refer to books and' articles describing the industry. The material for this paper is largely derived from published information on oil shale. Much of the information is obtained-from the books and articles mentioned in the list of references, and has been compiled with the intent of furnishing information to those not interested in all the details.

Jan 1, 1921

By James Westfield

A brief résumé follows of some of the most recent activities of the Division of Coal-Mine Inspection that have had a favorable effect. on health, safety, and injuries at coal mines: 1. There were approximately 8,510 active coal mines in the United States during 1955. In all, 82,389 regular Federal inspections of coal mines have been made since Public Law 49 became effective in May 1941; 9,823 of these inspections were made during 1955. 2. The Bureau of Mines introduced the revised Coal-Mine Accident-Prevention Course for Supervisors in the coal-mining industry on March 1, 1948. Since that date, 19,455 supervisors and those aspiring to official positions have completed such training conducted by personnel of the Division of Coal-Mine Inspection.

Jan 1, 1956

By K. T. Menzies

Over 1500 literature citations related to diesel exhaust sampling and analysis were obtained as a result of both computer and manual searches of nine data bases. Abstracts and hard copies of relevant citations were reviewed and those considered appropriate for evaluation were included in a bibliography. Based on the literature collected, available sampling and analysis methods for the following diesel exhaust contaminants were evaluated: CO, CO2, NO, NO2, Hydrocarbons, Particulates, PNA, S04, Oxygenates Emphasis was given to both laboratory and field methods for these species. Methods were evaluated on the basis of sensitivity, selectivity, accuracy and reliability and a selected list of preferred methods was developed for each compound/ class. The selected methods were additionally evaluated through communication with current investigators. Sampling and analysis methods for all compounds except CO and CO2 were observed to have some unreliability. Recommendations were made for future research to develop, improve, and validate methods.

Jan 1, 1979

By Sarkis G. Ampian

Crystalline silica (quartz, cristobalite, and tridyrnite) is regulated by the Mine Safety and Health Administration (MSHA) and Occupational Safety and Health Administration (OSHA) because of its potential for causing debilitating but nonmalignant lung diseases. In 1987, the International Agency for Research Against Cancer (IARC) conducted a review of the health literature and concluded that crystalline silica was a probable human carcinogen. As a result of this finding, OSHA was required to regulate crystalline silica under its Hazard Communication Standard (HCS). The standard requires that all materials handled by OSHA-regulated facilities be labeled according to the requirements of RCS and that workers receive proper training on the handling of the material if the crystalline silica content equals or exceeds 0.1 weight percent (0.1 %). MSHA currently is considering enacting its own RCS. This will be similar to OSHA's RCS. If the standard is enacted, most mineral producers will have to determine the respirable monitor filter and bulk crystalline silica contents of their ores and products so that workers and/or customers will know whether they are in compliance with the 0.1% HCS and/or the OSHA permissible exposure level (PEL) of 50 µg for an 8-hour workday for respirable crystalline silica as determined from monitor samples. Two major concerns with the RCS are the widespread occurrence of crystalline silica in nature and the suitability of current technology for routinely determining crystalline silica concentrations at the 0.1 % RCS level. Most ores are extracted from silica-bearing deposits and it is a common constituent of rocks and soils. OSHA's RCS will have the greatest impact on the producers of crushed stone, diatomite, dimension stone, gravel, industrial sand, perlite, pumice, pyrophyllite, sand, and talc because these materials frequently are shipped directly from the mill to the customer. MSHA's RCS would affect nearly all mineral producers. Those producers that have crystalline silica present in concentrations near the 0.1 % cutoff point will have the most difficulty with the analysis. Crystalline silica can be quantified at the 0.1 % level by X-ray diffractometry in simple systems containing one, two, and possibly three minerals if (1) none of the accessory minerals has X-ray diffraction reflections that coincide or overlap with those of crystalline silica and (2) the standard has a particle size distribution and crystallinity similar to those of the sample. In some instances, it may not be possible to determine the crystalline silica content of a sample with any degree of certainty using the recommended regulatory protocol. In all cases, it is recommended that a qualified mineralogist identify the minerals in a sample prior to any regulatory analysis. Additionally, the uncertainty as to whether some silica polymorphs should be classified as crystalline or noncrystalline and the suitability of metastable high-temperature standards, such as cristobalite and tridyrnite, for regulatory analysis at ambient temperatures should be addressed further. This overview is written both to highlight these problems and to serve as a guide for analysts, regulators, and industry personnel who are involved in the crystalline silica issue. It also covers some of the difficulties and/or shortcomings in quantifying crystalline silica, such as the ubiquitous mineral quartz, in the workplace.

Jan 1, 1992

By W. W. Adams

The first full year of the second World War for the United States presented a picture of the metal-and nonmetal-mining 4 industry which, without proper analysis and explanation, would convey a distorted view of achievements during 1942, especially because employment at gold and silver (lode and placer) mines-the largest group-declined to such an extent that the over-all totals for the country were reduced even though increases were made at mines producing copper, lead-zinc, iron, miscellaneous metals, and non-metals. A complete panorama of the metal-and nonmetal-mining industry, exclusive of coal mining, reveals a decrease in the number of men employed, the man-hours of employment, and the accident-frequency rates. Were the gold and silver (lode and placer) mines to be considered as a separate category; it would be seen that the number of men employed at all the other groups of mines increased appreciably over 1941. These other increases must be considered important, since these mines produced the vital war minerals that made valuable contributions to the military successes of the United States and its Allies during the year. A separate analysis of each of the various groups of mines may be found elsewhere in this bulletin. For the purpose of maintaining continuity in this series of bulletins, however, the discussion in this introduction will be confined to the entire metal-and nonmetal-mining industry (excluding coal mining, for which a separate bulletin, No. 462, has been published).

Jan 1, 1945

By H. F. Yancey

The development, manufacture, and sale of small coal stokers suitable for domestic use has provided a new industry in the United States at a time when badly needed. Sales of domestic stokers have doubled each year for the past 4 rears, until in 1936 probably more than 90,000 such units were put into use. According to reports of the Bureau of the Census 79,543 residential stokers were sold in the first 10 months of 1937 by 109 manufacturers. This rapid expansion has made itself felt in the coal-mining industry. The smaller sizes of coal, either in a sized or slack condition, are in greater demand; as a result, preparation practices at the mines have had to be revised so that, in many instances, lump coal is being crushed to meet the demand for stoker coal. This situation in turn has necessarily resulted in a realignment of price schedules for the different sizes. One of the first underfeed stokers small enough for domestic use was developed at Seattle, Wash., in 1912; in 1916, a small overfeed stoker was developed at Seattle. These two types are generally considered to represent the beginning of the present domestic stoker industry in the United States. A careful inquiry as to the number of domestic stokers now installed in the Seattle area, made by C. R. Pate, who was detailed to this duty by the Works Progress Administration, indicated that probably 7,000 domestic stokers are being used in this area for residential heating. Most of these stokers axe of the overfeed type, although in the past 2 years the underfeed type has made rapid gains.

Jan 1, 1938

The panic bars (and associated linkages and electrical circuitry) that are defined in this document are a machine operator-actuated control for the emergency deenergization of the tram motors on self-propelled, electric and diesel face equipment: including haulage equipment such as shuttle cars. There are nine basic types of panic bars (and several variations) that arc recommended in this document, but all of the panic bars are characteristically of the "fire door" type that is frequently encountered on outside exit doors of many public and some commercial buildings. It is also the intent of the following panic bar designs that, when emergency brakes are added to the face equipment machinery for which they arc required, that they be designed and hooked up so that actuation of the panic bar will result in automatic application of the emergency brakes (immediately following the deenergization of the tram motors). The following panic bar design requirements are a restatement of the proposed requirements defined in the Federal Register, requirements cited in "Guidelines for the Design and Installation of Devices for Deenergization of Self-Propelled Electric Face Equipment/Automatic Emergency Brakes" by C. E. Lester and J. D. Greenhalgh of MESA, and Bendix recommendations that were formulated as a result of discussions with personnel al the various machine manufacturers and underground coal mines that we surveyed, discussions with G. L. Judy (our consultant), etc:

Jan 1, 1974

By Lotfollah Nahai

India is one of the fortunate countries that has substantial reserves of many raw materials for producing steel; however, for historical and economic reasons these resources have not been aggressively developed until recently. Production of steel on an industrial scale started in 1912, but annual output was below 1 million tons3 in 1938 and about 1,500,000 tons in 1951. Expansion of the steel industry became one of the objectives of India's economic planning after independence in 1947. The Planning Com¬mission's 1951 report emphasized the importance of steel production, but financial obstacles, emphasis on river valley projects, and priority for increased food production in the First 5-Year Plan (1951-56) did not permit large-scale expansion of steel capacity. The 1956 planned target for crude steel, only 1,650,000 tons, was actually exceeded by production of 1,737,900 tons. In the Second 5-Year Plan (1956-61), however, construction of steel plants received a high priority. Currently three new steel plants, each with an annual capacity of approximately 1 million tons of steel, are nearing completion in Rourkela, Dorgapur, and Bhilai. Simultaneously, the two privately owned steel plants and the small State-owned plant in Mysore have been enlarged and modernized. As a result, India's crude steel capacity will be about 6 million tons in 1961, almost evenly divided between Government-owned and privately owned plants. Actual production in 1960 totaled 3,254,000 tons compared with 2,434,000 tons in 1959. Assuming that the population will be 430 million and that capacity production will be achieved, the 1961 per capita steel output will be only 31 pounds compared with 200 pounds for Japan in 1959. Some Indian experts feel that development of steel-consuming industries merits greater emphasis in the Third 5-Year Plan (1961-66) than expanding existing steel-producing facilities. Nonetheless, the Third 5-Year Plan calls for a 10 million ton annual capacity by 1966 to be achieved by expanding the Government-owned plants in Bhilai, Durgapur, and Mysore, and by establishing a new integrated Government plant in Bokaro, in the State of Bihar.

Jan 1, 1961