Search Documents

By W. J. Wenger

THIRTY-FOUR analyses of crude oils from the fields of the Four Corners Area of Arizona, Colorado, New Mexico, and Utah are presented and compared. The samples, taken from formations in four geological time periods, have high gravity and low-sulfur, -nitrogen, and -asphalt content. Generally, the oils are paraffinic in the low-boiling fractions, with increasing naphthenicity in the higher-boiling fractions. Oils from Cretaceous formations resemble other Cretaceous oils in the Rocky Mountains, but oils from Permian and Pennsylvania formations are unlike other oils of these ages in the Rooky Mountains. The differences in the oils are minor and cannot be used to distinguish between fields or between producing formations. With minimum special processing, the oils should yield large amounts of good-quality motor fuels. INTRODUCTION The only place in the United States where four States have a common junction is known as the Four Corners Area. This area (fig. 1) includes the northeast corner of Arizona, the southwest corner of Colorado, the northwest corner of New Mexico, and the southeast corner of Utah. It includes three major geological basins: The Black Mesa, the San Juan, and the Paradox. Major oil developments have occurred in both the San Juan and Paradox basins, but no discovery of commercial importance has been made in the Black Mesa basin.

Jan 1, 1960

By S. L. Weber, Y. H. Cheng, D. E. Banks, J. K. H. Ma

"The aggressive industrialization of America, the development of powered tools which generated massive amounts of respirable-sized dust particles, a latency period which may mask the relationship between exposure and development of disease, inadequate (or perhaps even careless) understanding of the relationship between dust exposure and disease, and respiratory protection which has later proven to be inadequate have resulted in a series of epidemics of silicosis which have caused the premature death of many workers.1-11 Emphasis on the regulatory control of dust levels in the workplace has greatly reduced the development of pneumoconiosis in the United States and in other developed as well as underdeveloped countries, yet the prevention of silicosis or coal workers' pneumoconiosis has not come close to being accomplished. Despite the public health perspective that pneumoconiosis arc totally preventable illnesses, there appears to be little evidence that this is the case.Cases of pneumoconiosis continue despite aggressive enforcement policies by regulatory agencies, attempts at dissemination of very readable materials aimed at workers and management 12.13 and respiratory dust exposure standards which are in place and appear, for the most part, protectivc.14- 16 It is more than frustrating for all parties associated with advocating workers' health to see reports of workers with aggressive silicosis. On another level, both the physician and the affected worker are helpless when a diagnosis of silicosis or coal workers' pneumoconiosis is made. Both realize that there is no proven way to affect the natural history of these progressive inflammatory and fibrotic processes. Neither is there any ""compassionate use"" therapy. What must be developed, at the very least, is a ""salvage therapy"" which has the potential to reverse, or at least dramatically lessen, the aggressive natural history of silicosis which develops over relatively short time periods. Because of the aggressive nature of silicosis (compared to coal workers' pneumoconiosis) attempting to develop a therapy for this illness should be a priority."

Nov 1, 1995

By Hal J. Kelly

A picture of the ceramic industrial potential of the Pacific Northwest States is presented by reviewing the present ceramic industries, raw-material resources, and current market demands. A resume is given of the industrial plants manufacturing ceramic ware as well as available information on raw-material resources. No attempt was made to prospect for new deposits but rather to evaluate, insofar as possible, those already known. Since much of the industry is concentrated on the Pacific coast, most of the information available on resources concerns deposits in that area. Large, undeveloped districts in Montana and Idaho, however, offer promise of larger reserves of ceramic raw materials. Average annual production, some operating costs, and annual power consumption are given for each of the plants. Production and some cost figures are listed to show the limited nature of the present industry and to suggest fields open for new development.

Jan 1, 1956

By Albert L. Toenges, Louis A. Turnbull, EDWARD L. FISH, JOSEPH J. SHIELDS, James J. Dowd

The stripping of coal with mechanical. equipment has progressed since the introduction of the first steam-powered shovel for the retóval of overburden at a mine in Pittsburg, Kans., in 1877...From the smart steam-powered shovels with dippers of less than a cubic yard capacity, small digging radius, and shovels that required manual moving, the trend has been toward large-capacity machines. Steam as power has been replaced largely by electricity, gasoline, and Diesel fuel, and dipper capacity as great as 35 cubic yards has been attained. Shovels and drag lines are self-propelled and revolve through 360°. The cost of these large-capacity modern machines is great, and in order to assure the return of the investment during the life of the property the reserve of coal in the area to be mined must be large;" Many comparatively small areas of coal suitable for strip mining exist, but these areas probably could not be mined, profitably with this large equip- ment. Therefore, heavy equipment has not been used in small areas because of the high cost in place of this equipment, the time and Atpense required to transport the machines to the mine site, and the construction of power lines if the machines are electrical powered.. Scrapers and light excavating equipment ane mobile, and the investment cost is not high. These units have been used in sirring the coal in small areas. A study to determine the methods in, yogue, and economic considerations involved in the use of such equipment was undertaken, and the information obtained is discussed in this report.

Jan 1, 1947

By Allan M. Johnson

Case histories were used to document and evaluate deficiencies in underground mine closures which have resulted in post-operation problems such as subsidence shaft failures, acid or toxic water drainage and others. Three different underground mining districts in the United States were investigated; 1) an iron mining district in Michigan 2) coal mining districts in eastern Ohio and southern Illinois and 3) three metal mining districts in central Colorado. Previous work in the Michigan district on problems with subsidence and acid water drainage provided the background from which the concept for this project was developed Student investigators working towards their MS degrees in Mining Engineering did the work on the eastern coal and western metal districts. The combined studies show that problems from acid water drainage, subsidence and inadequately protected mine shafts are the most severe and widespread. Suggestions of a technical nature are presented as partial solutions to some of these problems. It was determined that pre-closure evaluations could result in the identification of some potential problems that may occur after the mine is closed. Early recognition of these problems would be an advantage for at this time more options are available to the mine operator to either prevent them or to plan for their occurrence. Mine closure and reclamation should be considered as a part of mining and be incorporated in the mining plan. This would result in reduced environmental impact and would be achieved at a lower overall cost to the mining companies and to society. The role of water in the occurrence of several types of subsidence during mine flooding was significant at some mines in the Michigan district. These mechanisms which involve, friction reduction, gravity loading, overburden transport and hydraulic forces in a flooded mine probably have a broader effect than is currently recognized. Control of these processes may offer some interesting options during mine closure. It is recognized that technical solutions alone cannot provide all of the answers to problems associated with underground mines. Education, modified attitudes on the part of regulators and operators, and a more realistic perception of the importance and value of mining by the general public are also needed.

Jan 1, 1983

By J. W. Thompson

MINERALS OWNERSHIP AND POSSESSION. The owner of minerals under a conveyance from the surface owner does not lose his right or his possession by mere nonusage of the minerals. McBeth v. Wetnight (Indiana), 106 Northeastern, 407, p. 410, October, 1914. QUIETING TITLE TO MINERALS-PLEADING. A complaint in an action to quiet title to minerals and to the min- eral rights in certain land is insufficient in the absence of a direct allegation of possession, although it avers that the plaintiff from the time of receiving the conveyance assessed the mineral interest for taxes each year and paid the taxes thereon and exercised various acts of ownership of such mineral interests, in that he caused test pits to be dug on the land for the purpose of exploring the minerals and ascertaining their quality and extent, in going upon the land and looking after them from time to time, and that he accompanied or caused his agents to accompany prospective purchasers of such mineral interests and exhibited the same to such prospective pur- chasers in efforts to sell them. Fowler r. Alabama Iron & Steel Co. (Alabama), 66 Southern, 672, p. 673, Novem- ber, 1914. SALE BY MARRIED WOMAN-VALIDITY. A conveyance by a married woman of the mineral rights in certain described land is void where she had previously conveyed the land to another grantee who had acquired title by adverse possession under the deed.

Jan 1, 1915

By Anil Mahyera

Towards the goal of achieving uniform-high-tensions in roofbolts to provide superior roof support[1-7] for extended periods, Terra Tek installed mechanical-anchor bolts in a mine in eight different ways -- under torque/thrust control with and without hardened washers, belleville washers and tension equalization; in a conventional manner with and without a hardened washer. The various bolt groups were analyzed in terms of their tension uniformity and mean tension levels. Installing the bolts accurately with ? a hardened washer under the bolthead, and ? proper torque/thrust control resulted in the mast uniformly tensioned bolts -- with a coefficient of variation of only 14%, an improvement of 3 times over a conventional installation. Also, these bolts maintained a high tension level -- 80% of the installation tension, compared to 50% achieved conventionally.

Jan 1, 1982

By Raymond G. Travis

This paper, which describes mining methods and practices at the Hurricane Creek bauxite mine of Reynolds Mining Corp. in central Arkansas, is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs in various mining districts of the United States. The Hurricane Creek mine is in sec. 12, T. 2 S., R. 14 W., and sees. 7 and 18, T. 2 S., R. 13 W., Saline County, Ark., about 4 miles east of Bauxite. (See fig. 1.) Bauxite has been mined underground at the Hurricane Creek property since 1942. The operation is notable for relatively high recovery of bauxite under the adverse conditions of unconsolidated water-bearing overburden and unstable clay floor. Controlled caving, timbered stope walls, and efficient drainage systems on the surface and underground have minimized the problems and raised ore recovery about 25 percent above that formerly obtained.

Jan 1, 1961

By Raymond M. Stateham

The Bureau of Mines used portable infrared scanners to examine the surface of pillars and faces in the Somerset mine near Somerset, Colo. Zones of temperature buildup, indicative of potential combustion, were detected with the scanners; their existence was verified by temperature measurements with conventional instrumentation. Temperatures of 32° to 6° C were measured on surfaces with normal temperatures of 26° to 35° C. The infrared instruments and techniques appeared to offer a rapid and efficient method for locating potential trouble spots in mines susceptible to fires caused by spontaneous combustion.

Jan 1, 1974

By W. P. Yant

The widespread use of toluene in industry and the importance of air analysis in industrial-hygiene surveys have created a need for a simple and accurate method for determining toluene vapor in air. Most of the methods used to determine small quantities of toluene in liquid or vapor form are based on the measurement of its physical properties. Methods based on fractional distillation, determination of specific gravity, use of the interferometer, use of the spectrograph, and sorption on solid sorbents with subsequent determination of gain in weight have been employed. Distillation and specific-gravity methods are not applicable to the small quantities of toluene found in the air, and use of the interferometer, spectrograph, and sorption methods either are not specific for toluene in the presence of other volatile substances or require expensive equipment.

Jan 1, 1936

By Walter T. Lewiecki

Bauxite was first discovered in-the United States near Rome, Ga., in 1887, Approximately 400,000 tons of bauxite ranging from 46 to-62 percent alumina were mined in the area from 1888 to 1930. In February 1943, The Republic Mining & Manufacturing Co. installed a dryer and began mining and reworking dumps from the old bauxite mines. Some 3,000 long tons were dried and shipped to the chemical industries from March 1943, to June 30, 1943. In 1941 and 1942, representatives of the Bureau of Mined and the Federal Geological Survey/ visited this area and proposed an exploratory project that at first was to be confined to the Heritage district northeast of Rome (see fig; I). The Bobo district, southwest of Rome, was to be explored after work .1n the Hermitage district was completed. The Hermitage district comprises an area of about 50 square miles in the northwest quarter of Bartow County and the adjacent portion of Floyd County. It is bounded on the north by the Gordon County line, on the east by U. S. Highway 41, on the south by U. S. Highway 441, and on the west by State Highway 53.

Jan 1, 1949

By K. J. Liles

The Federal Bureau of Mines conducts a comprehensive test program on clay and shale at the Tuscaloosa Metallurgy Research Center. All samples are subjected to standard preliminary ceramic tests, which include firing formed briquets at temperatures ranging from 1,000° to 1,250° C to identify firing range and colors, and quick-firing to determine bloating characteristics. Materials that shop potential as structural products are further tested after either extrusion or dry-pressing. If the quick-fire test is positive, bulk samples can be fired in a rotary kiln to evaluate their potential as light- weight aggregate A number of miscellaneous tests also can be conducted if requested. These tests determine properties such as refractoriness (pyrometric cone equivalency), oil-bleaching characteristics, oil absorbency, viscosity for drilling-mud applications, sand-bonding properties for foundry usage, and pelletizing characteristics.

Jan 1, 1977

By W. P. Yant

The widespread use of toluene in industry and the importance of air analysis in industrial-hygiene surveys have created a need for a simple and accurate method for determining toluene vapor in air. Most of the methods used to determine small quantities of toluene in liquid or vapor form are based on the measurement of its physical properties. Methods based on fractional distillation, determination of specific gravity, use of the interferometer, use of the spectrograph, and sorption on solid sorbents with subsequent determination of gain in weight have been employed. Distillation and specific-gravity methods are not applicable to the small quantities of toluene found in the air, and use of the interferometer, spectrograph, and sorption methods either are not specific for toluene in the presence of other volatile substances or require expensive equipment.

Jan 1, 1936

Oil from shales has long been a source of fuel in foreign countries; however, in the fuel economy of the United States this source is classed as a reserve for future needs. In fad, shale oil has never been produced here in quantities necessary to establish oil-shale utilization as a sustained industry. The first known resources of stored energy that man endeavored to utilize were probably wood and water, and from these he directly obtained heat and power, respectively. With the evolution of man came the search for and the development and use of other natural fuel resources, the series progressing through the solid, liquid, and gaseous fuels until today those of one type can be converted into another, depending upon the use for which they are intended. The most important fuels are those that appear naturally in the most concentrated, conveniently obtainable, and usable forms. With the discovery of each new and more concentrated fuel there has been an appreciable increase in the importance of and number of devices for converting these fuels into energy.

Jan 1, 1938

The Waukon iron deposit comprises about 210 acres situated 2-1/2 miles north of Waukon, in Allamakee County, northeastern Iowa. The deposits have been exploited intermittently since 1899 and have produced about 67,000 tons of concentrated iron ore. From January to May 1943, the Bureau of Mines investigated the deposit to determine the extent of the ore-bearing material and its amenability to concentration, Seventy-one test pits were sunk. Those that indicated are of a grade high enough to warrant concentration tests were sampled. Average grade of ore was indicated to be 37.02 percent iron and 27.78 percent silica on a dry basis. Beneficiation tests indicated that the percentage of recovery might be relatively low.

Jan 1, 1949

By T. M. Romslo

The Lake Shore property, located in the early 1880's, contains copper-bearing deposits that have been developed by surface excavations, underground workings, and churn-drill holes. Operation of the property ended in 1929 with a total recorded production of 280,000 pounds of copper. The property is near the foot of the Slate Mountains, which are made up mainly of probably the Pinal formation of pre-Cambrian age. In the mine area there are a few outcrops of granite, which is exposed over a large area east of the property. Other outcropping rocks on the property are limestone, quartzite, and diabase. The limestone and quartzite probably are the Mescal and Troy formations of pre-Cambrian and Cambrian age, respectively. The predominant copper mineral is chrysocolla, a hydrous silicate that occurs mainly as fracture filling in bedded schist. It is also, the principal copper mineral in the shear zone at the schist-granite contact and in limestone southeast of the main workings. Investigation of the Lake Shore property by the Bureau of Mines included both topographic and geologic mapping, exploratory drilling, and metallurgical test work. One diamond-drill, hole and five churn-drill holes were completed for a total of 2,872.5 feet. Drilling started January 19 and was completed May 13, 1949.

Jan 1, 1950

By K. L. Williams

The Bureau of Mines laboratory tested the response of a commercially available real-time aerosol monitor (GCA RAM-1) to various dusts. Monitor measurements were recorded, averaged, and compared with simultaneous gravimtric measurements of each test dust. Tests usually lasted several hours. The test dusts of various particle size distributions used included coal, limestone, and a commercially available test dust. For each particular dust, the monitor response was linear and correlated well with mass concentration over the range of about 0.5 to 10 mg/m3. The monitor can estimate a 2.0-/m3 respirable coal dust concentration within as little as 26 pct with 95 pct confidence. The monitor must, however, be calibrated with the dust to be measured because the instrument response is affected by the type of dust particle. The average monitor response to same mass concentration of coal dust was approximately twice the average monitor response to the same mass concentration of limestone dust.

Jan 1, 1984

This report is a compilation of all information obtained in accordance with the requirements of contracts SO122076 and H0232056. A series of eight coal mines were visited to determine their communications usage and requirements. Presently available equipment was surveyed and evaluated to determine its applicability to the needs of the mines. The equipment studied includes that made by the following companies : Anaconda Telecommunications Division Andrew Antenna Bendix Communications Division Collins Radio Group of Rockwell International Executone Communication and Sound Systems Gau-tronics Mine Safety Appliances Company Motorola Communications and Electronics, Inc National Mine Service Company Plessey Communications Systems Corp Pye Electronics Limited Reach Electronics Set Com Corporation Sonex Incorporated Mine visits and in-depth interviews were made alt the following sites: Robena No. 4, Pennsylvania Greenwich Colliery Mines, Pennsylvania Somerset Coal Mine, Colorado Keystone No. 1, West Virginia Harris Mine No. 1, West Virginia Baldwin Underground No. 1 Mine, Illinois Lovilia No. 4 Coal Mine, Iowa Orient No. 3 Coal Mine, Illinois

Nov 15, 1974

By F. A. Rutledge

The Batesville district in north central Arkansas is one of the important sources of manganese ore and ferruginous manganese ore in the United States, with a history of production dating back to 1849. From studies by the Federal Geological Survey, it was recognized that the district probably still contains substantial reserves of low-grade ore. It was natural, therefore, that the deposits in this area should be among the first investigated by the Bureau of Mines under the Strategic Materials Act of June 1939, by which the Bureau was authorized to explore domestic deposits of strategic minerals, at that time designated as those of antimony, chromium, manganese, mercury, nickel, tin, and tungsten. The field work of the Bureau of Mines in the Batesville district was done in two distinct phases. Under project 308, active from August 1940 to June 1941, carbonate-oxide ores were investigated at five separate areas in which 100 trenches, test pits, shafts, and edits aggregating 4,364 linear feet were excavated and 839 samples were taken and assayed. Under project 323, in progress from February 1941 to January 1942, wad deposits were explored at 10 separate areas by 408 prospect shafts, churn-drill holes, and bucket-drill holes aggregating 23,680 linear feet from which 285 samples were taken and assayed. Processes for beneficiating the wad ores were investigated at ore-testing laboratories of the Bureau of Mines.

Jan 1, 1952

By Robert V. Spencer

"This report describes an examination and preliminary exploration of the Magnet Cove Rutile Co. property in Hot Spring County, Ark. The company in 1944 was producing titania for use in-the welding-rod and metallurgical industries but later ceased operations. The deposit appeared to contain potential reserves of rutile ore, and the Bureau of lanes in 1945 conducted an examination designed (1) to obtain samples for ore-dressing tests and (2) to gather information regarding the grade, character, and size of the deposit. This report presents the data obtained by geologic mapping, geophysical surveying, churn drilling, and core drilling. Beneficiation tests are being made at the Bureau of Mines Rolla, No. station, on the samples taken and will be discussed in a later report.The Magnet Cove operation had been called to the attention of the Bureau of Mines, and in view of the potential reserve of titanium-bearing material, it was decided to obtain samples for ore-dressing tests. Churn drilling was selected as a means of obtaining representative samples, and geologic mapping and geophysical surveying were done to throw more light on the nature of the deposit. Subsequently, a few holes were core-drilled.The property contains the NE1/4, W1/2 fractional NW1/4 and 82 acres of the N part of SE of sec. 18, and -29 acres of the SW1/4 NW1/4 sec. 17, all in T. 3 S., R. 17 W., Hot Spring County, Ark. The mine and mill are about 1 mile by graveled road northeast of U. S. Highway 270, a paved road connecting Malvern, 10 miles south and Hot Springs, 12 miles west. The area is served by two railroads, the Missouri Pacific, which passes through Malvern and Hot Springs and the Chicago, Rock Island & Pacific,,has a line connecting Malvern and Hot Springs an passes about 2 miles south of the property. A natural-gas pipe line and an electric power line reach the property."

Sep 1, 1946