Search Documents

By James M. Spear

Sample results suggest the only mineral resources in the study areas are placer gold deposits along the South Fork Kern River in the Woodpecker RARE II unit (fig. 1). These deposits, in Rockhouse Basin, total 4.5 Figure 1.--NEAR HERE. million cu yds (3.4 million cu m) of indicated subeconomic gold resources in four deposits of "older" gravel. Gold value in samples averages $0.36 per cu yd ($0.47 par cu m) and is as much as $4.44 per cu yd 1/. Cost of mining the gravel and recovering the placer gold is estimated to be more than $2 per cu yd ($2.62 per cu m) for a deposit of this size and type. Additional inferred subeconomic placer gold resources with similar grade probably occur in four other deposits of "older" gravel on which no mining claims were located. Placer gold occurrences on upper Trout Creek contain gold worth as much as $4.50 per cu yd ($5.88 per cu m) 1/. Average grade is much lower, and only about 1,000 cu yds remain (760 cu m). These occurrences do not constitute a resource, but may attract hobbyists not dependent upon making a profit.

Jan 1, 1982

By Forrest T. Moyer

THIS CHAPTER of the Minerals Yearbook contains injury experience and related employment information for the coal-mining, coking, oil and gas, peat, and native asphalt industries in the United States for 1963. No attempt has been made to combine these data and present injury-frequency rates reflecting the mineral-fuel industries because the hazards of the separate industries are not comparable. Tabulations showing the trend of injuries and employment for all mineral industries are presented in Volume III of the Minerals Yearbook. COAL Injury experience of the coal-mining industry was improved slightly in 1963, as measured by the 2-percent decline in the Injury-frequency rate. Although the total number of fatal and nonfatal injuries increased 1 percent, the greater proportional increase of 3 percent in man-hours worked accounted for the improved frequency rate. Employment and injury data for 1963 are based on final data for anthracite mines and preliminary data for bituminous coal and lignite mines.

Jan 1, 1964

By D. V. Gaffney

This report presents the results of a three-phase investigation of the feasibility of using cemented coal waste in active underground coal mines to prevent mine subsidence. Coal caste was broadly defines to include waste from both coal preparation plants and coal-fired power plants. Underground systems with potential for cemented backfill are determined through identification of current mining methods and available technologies for cemented backfilling and consideration of materials and systems constraints upon mining and backfilling integration technical concerns including operation, health and safety, materials utilization, environmental impact, applicability and techni¬cal status are assessed for six (6) systems which were identified as potentially feasible. Two (2) of these systems are conceptualized in a hypothetical case history and developed to further assess their operational and economic feasibility. Comparisons of costs among both systems and with costs of surface disposal are presented. Also presented are the conclusions reached concerning the present feasibility of using cemented backfill in active coal mines and potential avenues for further research. Appendices contain further consideration for design of cemented mixtures to be used in backfilling, the results of laboratory testing of mixtures rich varying concentrations c: waste products and cementing agents, and an annealed bibliography

Jan 1, 1981

By Harold M. Smith

This report presents a complete qualitative picture of knowledge of the composition of petroleum as of April 1965. The material is presented in detai 1 on two imaginative maps--one, the Hydrocarbon Hemisphere, depicts the hydrocarbons that have been identified in petroleum; the other, the Heterogeneous Hemisphere, shows the sulfur, nitrogen, and oxygen compounds that have been found. All compounds are placed on the maps according to boiling point. The accompanying text illustrates by structural formulas the several types of hydrocarbon and nonhydrocarbon compounds identified, presents some quantitative data, and points out the possible geochemical significance of a number of the compounds. The possibilities of the Petroleum World of the future are discussed as a function of needed research.

May 1, 1965

By Llewellyn A. Rubin

ROUTINES AND SUBROUTINES A- 1 Wait Loop (Wait) A- 2 Receiver Processing (RCVP) A- 3 Control Panel Sequence (CPNL) A-4 Interrupt Routine (INTRP) A- 5 Math Processing Routine (PROC) A-6 Input Constants for Math Routine (CONI) A-7 Angle Conversion Routines (LVERT) A- 8 Display Routine (DSPY) A- 9 Message Print Auxillary Routine (MESSO) A-10 Auxillary Subroutines (AFUTC and AGETC)

Jan 1, 1973

The Hopi Reservation is in Arizona, where coal mining can be traced to the 13th century. Bituminous coal is found in varying quantities throughout the Hopi Reservation. The Hopi Tribe has a 50 percent mineral interest in the coal resources of the joint-use area adjacent to the Navajo reservation. The only coal presently mined on acornrnercial scale from lands in which the Hopi Tribe has an interest is from the Wepo formation at the Black Mesa and Kayenta Mines. These two large surface mines, located over 50 miles northeast of most Hopi settlements, have disturbed more than 6,000 acres. Income from royalties generated by the mines provides significant economic support for the Hopi Tribe. The Office of Surface Mining's Albuquerque, New Mexico, Field Office is responsible for regulating mining and reclamation on Hopi land. The Hopi Abandoned Mine Land Program was approved June 28,1988.

Jan 1, 1992

By Thomas J. Peters

Tungsten, silver, lead, zinc, and placer gold occur in the Cucamonga B RARE II area (no. B5174). A strata-bound, scheelite-bearing zone at the Blue Diamond prospect (fig. 1, no. 1) contains an estimated 16,000 tons (15,000 t) of identified, subeconomic resources averaging 0.16 percent tungsten trioxide (W03). There is a high potential for discovering additional tungsten resources at this property. The California-Hercules prospect (fig. 1, no. 5) ha; a mineral occurrence which contains an estimated 1,000 tons (900 t) of tactite averaging 1.3 oz silver per ton (45 g/t), 0.75 percent lead, and 0.72 percent zinc. Another occurrence, at the Blew Jordam Prospect (fig. 1, no. 4) has an estimated 100 tons (90 t) of tactite averaging 10 oz silver per ton (340 ,/t), 3.75 percent zinc, and 2.3 percent lead. There is a moderate potential for discovering silver, lead, and zinc resources at these prospects, which are in metamorphic pendants. There are a few lode gold prospects in the area (fig. 1, nos. 3, 11, 14) are on geologic structures which parallel the San Andreas Fault, northeast of the area. These deposits are not well exposed and have been historically unproductive. Placer gold in area B occurs locally in the beds of intermittent tributaries to Lytle Creek (fig. 1, nos. 10, 12, 13) in concentrations as high as $1.17 per cu yd ($1.53/cu m, at a gold price of $450 per troy oz). The deposits have no significant volume, but could be utilized for recreational panning and suction dredging. In the Cucamonga C RARE II area (No. C5174) placer gold occurrences locally contain as much as $1.23 per cu yd ($1.61/cu m). However, gravel containing the gold appears to be limited to stream beds, and does not occur in sufficient quantity to constitute resources. Recreational panning and dredging also may occur in this area.

Jan 1, 1983

By David A. Lipton

U.S. Bureau of Mines personnel examined mines, prospects, and mineralized areas to determine the mineral resources and potential of the Moses and Dennison Peak RARE II areas in Tulare County, California. These areas, along the west slope of the Sierra Nevada, are underlain by grarnitic rocks of the Sierra Nevada batholith and contain numerous metasedimentary roof pendants. Silver, copper, and zinc occur in contact-metasomatic deposits within the metasedimentary rocks. In the Moses area, the Powell Mine (fig. 1) contains an estimated 90,000 tons (82,000 t) of subeconomic silver, zinc, and copper resources. The King Solomon Prospect has 3,000 tons (2,700 t) of silicified phyllite containing zinc. On the Helen-Joyce Prospect, 44,000 tons (40,000 t) of gossan occur above a poorly exposed silver-zinc rich zone. Potential exists for additional mineral resources and occurrences at each of these properties.

Jan 1, 1983

By David A. Lipton

In 1980, the U.S. Bureau of Mines conducted a mineral survey of the 23,500 acre Garcia Mountain RARE II area (No. 5107) in the Los Padres National Forest. Bureau of Mines data indicate a low potential fur gold, silver, and mercury resources. Twenty-nine placer samples, representative of small yardages, showed small amounts of gold or other economic mineral values. Mercury deposits in faulted siliceous rocks in the Franciscan Formation occur north of the area. Similar rocks are in the southwest part of the study area, but apparently contain no mercury deposits. Geothermal and oil and gas potential is low.

Jan 1, 1982

By W. J. Wenger

Colorado has been producing petroleum since 1863 but only recently has become a major oil State. The first well was drilled on Oil Creek near Florence, but out-put was relatively small until discovery and development of the Weber sandstone reservoir at Rangely. Oil was discovered in the Weber sandstone in 1933, and the reservoir was developed after 1940, bringing Colorado, in 1949, to 11th place among the 48 States as an oil producer. Colorado's output increased further because of the discovery and development of many fields in the Julesburg Basin since 1949 By 1954 Colorado was in ninth place and maintained that position through 1955.4/ Between 1946 and 1951, Colorado's oil production more than doubled, while the total United States production increased only 25 percent. It seems probable that production will continue to expand in Colorado for many years. This report presents analyses of 92 crude oils from 73 fields representing 90 percent of the production in 1955. Abridged analyses are listed for easy comparision, and complete analyses arc given in the appendix. Oil samples were collected for study from many different sources. Although many of the newer fields were not sampled, their oils probably are very similar to those from corresponding formations that were studied and tabulated.

Jan 1, 1957

By M. E. Tyrrell

To promote greater use of abundant domestic raw materials in the manufacture of synthetic mullite, the Bureau of Mines has undertaken a comprehensive investigation to determine the effects of the impurity oxides TiO2, Fe203, and alkali on physical properties of sintered mullite-forming mixtures. The first part of the report presents the results of work covering a major area within the mullite study; namely, the effect of impurity oxides on volume stability, one of the outstanding characteristics of mullite refractories. The volume stability of 20 compositions in each of 3 alumina- to-silica ratios, which blanket the range commonly found in purchase specifications, has been determined following procedures of Navy Specifications B-15606 A for Grade A high-alumina refractories. Results indicated that so long as 5 percent of impurities are combined approximtely in the proportions of 3 percent Ti02, 1 percent Fe203, and 1 percent alkali, sintered mullite-forming compositions in the almina to silica range tested will be volume stable. A permissible tolerance of one-half per- cent in each impurity oxide provides a range that includes values common in the natural minerals from which sintered mullite may be made. Within the total range of 5-percent impurity mixtures, a greater number of volume-stable compositions were obtained by increasing the alumina-silica ratio.

Jan 1, 1962

The Mine Safety and Health Administration (MSHA) defines an independent contractor as “any person, partnership, corporation, subsidiary of a cor-poration, firm, association or other organization that contracts to perform services or construction at a mine.” Contractors that perform specific types of work are required to report the number of employees who work at coal mines and noncoal mines.

Sep 1, 2007

By D. F. Hambley

This report documents the work carried out by Engineers International, Inc. and its subcontructor, W. G. Pariseau, in order to develop a design manual for ore passes for open pit mines. The work included an extensive information search, novel analyses in rock flow theory, cost and time estimation for shaft and raise construction methods, and development of design criteria for the are pass proper, dump point, and draw point.

Jan 1, 1983

In 2006, 14,885 mining operations reported employment data to the Mine Safety and Health Administration (MSHA).1 Almost half (48.2%) were sand and gravel mines, followed by stone mines (30.7%), coal mines (14.2%), nonmetal mines (5.0%), and metal mines (1.9%).

Jan 1, 2008

By Larry A. Lass

The U.S. Bureau of Mines, in cooperation with the Iron Range Resources and Rehabilitation Board, investigated the potential of using northeastern Minnesota papermill waste sludges as a binder for Mesabi Range iron ore (taconite) concentrate. Sludges from five different commercial papermill waste treatment operations were evaluated in laboratory tests. Except for the coarsest sludge, all were fairly easy to blend with the taconite concentrate using conventional mixing methods. The coarsest sludge had to be reslurried at 2 pct solids before adding it to the concentrate in order to obtain pellets without visible sludge clumps. Drying and grinding the sludges made them less effective as binders because of a lower degree of rehydration. On a dry weight equivalent basis, twice as much raw sludge binder was required to obtain similar pellet physical properties as with bentonite; however, the pellets made with raw sludge had superior metallurgical properties. Over 30 pct higher reduction rates and over 1500 C higher softening temperatures were obtained with sludge binder than with bentonite. Sludge D, which had the lowest fiber and the highest alkali metal content, resulted in the lowest reducibility enhancement. Even though more raw sludge was required than bentonite, the sludges have virtually no value, and therefore may provide a cost-effective additive binder for producing improved metallurgical-quality pellets. Large-scale testing has not been done to confirm these laboratory results.

Jan 1, 1989

By Pablo Velasco

After becoming an oil exporter in 1972, Ecuador experienced a remarkable economic upswing until 1978. However, in 1979 and 1980, a combination of only slight improvements in agricultural output and stagnating petroleum output lowered rates of real gross domestic product (GDP) expansion to 5.3% and 4.3%, respectively. In current prices, the GDP in 1980 was estimated at $11.3 billion.2 The slowdown in growth is attributable in large part to the low level of petroleum exploration in the 1972-79 period. Ecuador's production of petroleum declined 4.5% in 1980 compared with that of 1979. The consortium of Corporación Eatetal Petrolera Ecuatoriana (CEPS), the State oil company, and Texaco, Inc., operating in Ecuador's eastern jungle region was responsible for nearly all of 1980 production, The volume of total crude petroleum exports from Ecuador dropped from 44.7 million barrels in 1979 to 40 million barrels in 1980, although crude petroleum export revenues rose from $1,032 million in 1979 to $1,294 million in 1980- The latter figure represented 54% of Ecuador's 1980 merchandise exports. Crude oil exports accounted far about 46% of the value of 1979 merchandise exports. The total nonfuel mineral exports in 1980 were valued at less than $1 million.

Jan 1, 1982

By A. E. Ketler

The Bureau of Mines Research Program has defined per coal miner's illumination needs. Due to similarity in the environment in which coal and Hardrock miners work, coal mine illumination technology has been applied to Hardtack room and pillar mines.

Jan 1, 1977

This publication summarizes, for potential contractors and all other interested parties, the research and development of in-house and contract projects programmed by the Bureau of Mines for fiscal year 1983 (October 1, 1982-September 30, 1983) under its Health and Safety Technology program. The objective of these projects is to provide an ordered and sequenced series of advance toward the Bureau's overall goal of providing the systems technology required to create a more healthful and safer working environment for the Nation's mining and minerals processing workers.

Jan 1, 1982

By John K. Owens, Wayne L. Howie

Mobile roof support (MRS) machines are used as roof support during pillar recovery in retreat operations in lieu of wooden posts, cribs, or hydraulic props. A Mine Safety and Health Administration-permissible load rate monitoring system was developed for the MRS by researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health. The system uses a dedicated embedded processor to monitor changes in pressure inside the hydraulic cylinders of the MRS through multiplexed data acquisition channels and converts these pressure changes to load rates that sequentially activate three load-rate-indicator lights mounted on the machine. Each light represents a different loading rate to alert mine personnel to dangerous conditions during pillar extraction.

By Mackenzie Burnett

This program was initiated by USBM to quantify the respirable dust problem caused by the use .of roadheaders in underground metal/nonmetal mines with special emphasis on this problem in uranium mines. The contract called for the development of methods or equipment to alleviate the respirable dust and to implement the solution in a mine. Attempts to quantify the dust problem were made in the following way: survey of MSHA records, survey of state mine enforcement agencies, survey of mine records, dust measurements taken at two mines using roadheaders. The results of this study are not conclusive due to very limited and sometimes less than useful data; however, the study does indicate that a serious dust problem could and may exist. If and when roadheader use becomes more popular, it is almost certain that development of dust control procedures and equipment will be necessary. This contract was concluded without developing this equipment since only one roadheader is currently in use in an American uranium mine and the mine prefers not to participate in the program at this time. This report discusses the available data concerning respirable dust problems and presents a solution which can potentially help to solve the problem. The solution requires the use of blowing ventilation, on-board dust extraction at the source, and filtration, as well as continued use of water sprays. The on-site tuning of such a system is necessary to demonstrate the degree of improvement possible.

Jan 1, 1981