Search Documents

Papers presented at a U.S. Bureau of Mines (USBM) technology transfer seminar describe the causes of violent material failure in U.S. mines, measurement techniques for monitoring events that result in violent failure, and mitigation techniques for controlling failure. Specific factors contributing to violent failure are identified on the basis of geotechnical monitoring in 16 U.S. hard-rock and coal mines and on statistical analyses of 172 coal bump events. New monitoring and analysis techniques developed as tools for assessing violent failure; geotomographic methods that provide new capabilities for the study of material failure and stress changes over large areas; and seismic methods for determining source locations, calculating energy release, and determining source mechanisms are described. Fair correlations have been established among seismic parameters, elastic stresses, face support load, and violent events. USBM studies have identified the advantages using both yielding and stable pillars for coal bump control. A computer program has been developed as an aid for selecting room-and-pillar layouts. The practical aspects of implementing a destressing program is outlined for coal mines, while the importance of mine orientation and timely support installation in controlling buckling-type failure is identified for hard-rock mines.

Jan 1, 1995

This sheet explains your audiogram (hearing test) and gives some basic information about protecting your hearing. Keep it so you can refer to it later. What is an audiogram? • An audiogram is often called a “hearing test,” but there’s no pass or fail • It is a written record of your hearing levels • A series of audiograms can track changes in hearing over time • Your hearing threshold levels (the quietest sounds you can hear) are measured in decibels (dB) at different frequencies from low (500 Hz) to high (8000 Hz) Why should I get audiograms? • To measure your hearing ability • To identify hearing problems • To monitor success at maintaining your hearing • To see if noise exposure is affecting your hearing Do I have normal hearing? Compare your hearing threshold levels to this scale: -10 – 25dB Normal hearing 26 – 40 dB Mild loss 41 – 55 dB Moderate loss 56 – 70 dB Moderate/severe loss 71 – 90 dB Severe loss 91 – 100dB Profound loss [ ]

Jan 1, 2008

By John J. Baz-Dresch, Kenneth L. Bickel, Winthrop F. Watts

Catalyzed diesel particulate filters (CDPF's) reduce the concentration of diesel particulate matter (DPM) and may reduce the emissions of carbon monoxide (CO) and hydrocarbons (HC) in diesel exhaust. Asamera Minerals' Cannon Mine first installed CDPF's in 1987, and currently has 12 diesel- powered vehicles equipped with CDPF's. The Cannon Mine and the U.S. Bureau of Mines collaborated to evaluate the durability and performance of a CDPF. One of the CDPF's used at the mine was periodically evaluated in the USBM's diesel emissions laboratory after 839, 1,584, and 2,881 h of in-mine service. The objectives of this report are to present results from the USBM's evaluation of this CDPF, to describe the Cannon Mine's experience and cost analysis of using CDPF's, and to make recommendations for the future use of CDPF's. CDPF's improve air quality at the Cannon Mine, but they frequently become plugged and are subject to excessive mechanical shocks and stress, shortening their useful life. Mine records indicate that CDPF's account for 0.8 to 4.9 pct of the vehicles' operating cost at the mine. CDPF life to date has ranged from 1,671 h to more than 5,992 h. Laboratory tests of the CDPF determined that DPM removal efficiency decreased and regeneration temperature increased over time.

Jan 1, 1994

By Paul J. Remington

The field data gathered as part of the measurements described in Volumes I and II were re-analyzed in the low frequency regime (.1 Hz to 1 Hz) where motion sickness normally occurs. These data were compared co the international standard ?ISO 2631 Addendum 2: Evaluation of exposure to whole body z-axis vertical vibration in the frequency range 0.1 to 1.0 Hz." For both underground mining machines and surface mining machines the results showed that one would not expect motion sickness to .be a severe problem. New field data were gathered on the vibration reduction performance of various seat designs found on surface coal mining machines. The vibration during normal operation was measured on the seat using the standard seat pad accelerometer package described in the previous two volumes and simultaneously on the floor of the machine at the base of the seat. Preliminary indications are that the so-called high performance seats used for operator vibration reduction do not offer significant improvement over conventional seats.

Jan 1, 1984

By Thomas A. Giordano

Portable communications equipment is becoming increasingly important in underground mining. Proper selection of microphones and hearing devices to be part of these communication systems is essential if the messages are to be transmitted intelligibly. In this program a thorough study of the requirements for these transducers was made with respect to intelligibility, mechanical configuration, human factors and safety. A computer analysis was made to predict how several combinations of transducers would perform at typical mining noise levels. A survey has been made of those microphones and hearing devices on the market today that might be applicable to the miner communication system. Several systems are proposed and evaluated.

Jan 1, 1976

By James L. Eirls

Tracor MBA under a contract to U.S. DOI Bureau of Mines designed, developed, fabricated and demonstrated a conveyor belt service machine. It is self-contained, battery powered, rubber tired and capable of handling, storing and transporting conveyor belting, wire rope and associated structures for sectional conveyor belts. While moving the tail section to its next position the machine discharges the belting, wire rope and belt structures. The belting is elevated and separated to provide for the insertion of the structures with minimum expended effort. A hydraulic system provides the power for steering, braking, winding or unwinding under controlled tension the belting and wire rope, operating a load-bed slat conveyor, raising, lowering and locking connection hitches and powering external hydraulic tools. Also, a pneumatic system is available to operate air impact tools. The service machine, with its present components can function in coal seams as thin as 48 inches, double wind conveyor belting 42 inches wide, 400 feet long, load or unload 3/4" wire rope on two separate reels and is controlled by two operators. A complete belt move using this machine requires only four workers. Successful underground demonstrations were conducted in coal mines located in West Virginia and Kentucky.

Jan 1, 1983

By J. Mitchell Linne

The principal mineral commodity in the Orleans Mountain RARE II area (No. 35019) is gold. Gravel deposits along the Salmon River contain placer gold. Lode gold with associated silver is contained in quartz veins. Many placer mining claims have been located within the study area in the Salmon River district. Four placer patents totalling 230 acres were issued for claims on the Salmon River between Lewis Creek and Forks of Salmon. On this same reach of river, adjoining and overlapping the study area boundary, approximately 3.3 million cu yd (2.5 million cu m) of gold bearing gravel with values ranging from $0.51 to nearly $5 per cu yd (50.66 to $6.50 per cu m) (gold valued at $400 per troy oz), are contained in three placers, the Bloomer, Pot Luck, and Horn (table 1). Within the study area boundary there are approximately 950,000 cu yd (726,000 cu m) of gold bearing gravel in these three placers. These three mines yielded nearly 12,000 oz (373,000 g) of gold and more than 300 oz (25,000 g) of silver between 1872 and 1913.

Jan 1, 1982

Electrical trailing cables are frequently damaged in usage, especially on continuous minors, and because of their weight and damaged condition present a safety hazard to personnel required to handle them. The U.S. Bureau of Mines and FMC Corporation signed Contract No. HO 122011 in August 1971. One of the contract tasks was to study the feasibility of techniques to improve trailing cable support and handling of power cables on underground coal mine machinery and to design a cable-handling device for a continuous mining machine. This report presents the results of the feasibility study, describes the design for a proposed cable handling device and concludes with a recommendation for future action to construct a test rig to evaluate the cable reel system.

Jan 1, 1972

By Patrick A. Hamilton

This Bureau of Mines report delineates the coal reserve base of anthracite, bituminous and subbituminous coals, and lignite, by mining method and sulfur content, for coal-bearing States west of the Mississippi River. The parameters used to establish the reserve base definition are the result of a joint agreement by the Federal Bureau of Mines and the U.S. Geological Survey. The reserve base of low-sulfur coal, =10 percent sulfur, is 167,324.5 million tons; medium-sulfur coal, 1.1-3.0 percent sulfur, is 37,531.5 million tons; and high-sulfur coal, >3.0 percent sulfur, is 11,244.1 million tons. The reserve base of coal with an unknown sulfur level is 18,323.0 million tons. The percentages of deep and strippable coal are 56 percent and 44 percent, respectively. The basis for reserve base estimates and analytical data for this report was the Fuels Availability System, a Bureau of Mines data bank containing numerous data tin fossil fuels. Information contained in the system was obtained from publications of the Bureau of Mines, U.S. Geological Survey, State agencies, private publications, and company data.

Jan 1, 1975

By D. S. Burgess

This report summarizes the incidents that preceded the December 9, 1970, propane-air explosion in Port Hudson, Mo., and then attempts to establish the nature of the explosion from the ensuing events. Special emphasis is given to possible ignition sources, the distribution of flammable vapors, and the analysis of blast damage. Both near-and far-field damage indicated that this explosion may be attributed to the detonation of propane in air with an energy release equivalent to that from about 50 tons of detonating TNT.

Jan 1, 1973

By Doss H. White

In 1989, Alabama's nonfuel mineral industry produced a State record of $463 million of nonfuel mineral commodities, an increase of $4 million over that reported by the State's mineral producers in 1988. The new record marked the fourth consecutive year in which mineral production increased over that of the previous year. Alabama ranked 22d among the States in total mineral value. Cement, stone, and sand and gravel were the three leading mineral commodities produced, accounting for 77% of Alabama's total mineral value. During the year, there were several acquisitions by Alabama cement and stone companies, and the only tantalum mine in the United States completed its first full year of operation.

Jan 1, 1991

By Andrew M. Leszcykowski

This report represents the first comprehensive accounting of lode mining sites in the Sheep Mountain mining district, Custer County, Idaho. Twenty-one mine and prospect locations have been added to the Bureau's Mineral Industry Location Subsystem (MILS) data base as a result of initial phases of a mineral appraisal of the River of No Return Wilderness; previously known locations were checked and the updated information added to the data base. The district's deposits are mainly confined to metasedimentary xenoliths in granodiorite and quartz monzonite. Those deposits in the north and west parts of the district are lead-silver-zinc replacement veins in dominantly calcareous facies; those in the southern part of the district are polymetallic fissure-veins containing pyrite, chalcopyrite, arsenopyrite, galena, and sphalerite hosted by micaceous schist and phyllite. The dominant structural trend in the southern part of the district is northwesterly and on strike with major deposits in the adjacent Seafoam mining district.

Jan 1, 1983

By Gerald P. Scanlan

Control of the dust produced by continuous mining machines in coal mines is generally obtained by water sprays from fixed nozzles mounted on the frame of the machine in back of the cutting head. Mounting the nozzles on the rotating head of the machine closer to the coal cutting bits may improve the efficiency of dust suppression. To test this concept, respirable dust measurements were made during 39 regular production shifts in an underground mine using a Joy 11CM continuous miner. The equipment used, difficulties encountered, and measurements obtained are described.

Jan 1, 1974

By Robert F. Stewart

The oxidation of structural materials at high temperatures in gas-cooled systems can be greatly retarded by the addition of small amounts of hydrogen to the inert coolant. In experimental equipment for gasifying coal with heat transferred by helium, the oxidation of graphite and metals (molybdenum, tungsten, and certain stainless steels) by trace impurities in the coolant helium was virtually eliminated by adding 0.1 to 1.0 percent hydrogen. The reaction of hydrogen with praphite does not preclude its use to retard oxidation; at 2,400° F. only 0.2 pound of graphite per square foot per year is lost for each percent of hydrogen in the helium. The addition of hydrogen appeared to prevent the mass transfer of carbon often associated with oxidation of graphite, without causing noticeable embrittlement of stainless steels and molybdenum or other damaging effects. This method has been tested in precision gas-recycle systems and applied successfully for more than a year in a pilot-scale unit operating at 250 pounds per square inch gage and 2,400° F. It is now used routinely and can be applied to many gas-cooled systems operating at high temperatures.

Jan 1, 1962

By R. V. Ramani

The overall objective of this study is to contribute to the reduction of the quartz dust hazard in underground coal mines through a better under-standing of the sources and generation of airborne quartz dust. This research project has included extensive experiments in operating mines for (1) documenting the amount of respirable dust generated, (2) measuring the quartz levels in host materials and airborne dust, (3) analyzing the size consist of the mined product, and (4) establishing the relationship between these various parameters. The results of the study indicate that the amount of dust airborne is a very small fraction of the total (<15 µm) and respirable (<7 µm) dust generated. The quartz contents in the total and respirable airborne dust are generally higher than those in the host material. Quartz content increases with decreasing size of airborne dust. Also, it appears that rock breaks into a different size distribution than coal. The source of quartz for the airborne dust appears to be the roof and the floor material rather than the coal seam itself. No general relationship is found between the Hardgrove Grindability Index and either the quartz content in the airborne dust or the amount of respirable dust. Extended descriptions of the experimental design, the experiments, data analyses and results are presented in this volume. The raw data, the data management computer program and the sampling and safety plan are presented in Volume 2.

Jan 1, 1987

By Mary F. Koehler

Continuing a program of thermochemical investigation of compounds of to ferroalloy elements, this paper contains ins values of the heats of formation of two sodium molybdates (Na2Mo04 and Na2Mo207) and three sodium tungstates (NO2W4, Na2W207, and NA2W207, and Na2W4013). The experimental method was solution calorimetry. The solution medium was sodium hydroxide solution, except that hydrofluoric acid solution was used for sodium tetratungstate. The heat of formation values are given with reference both to the constit¬uent elements and to the constituent oxides. These data are of prime impor¬tance in the thermodynamic consideration of these substances, as their accumulation includes the most difficult and time-consuming steps toward evaluating the free energies of formation and thus the potential reactivities and thermal stabilities. Except for values for sodium monomolybdate and monotungstate, no previous similar data were contained in literature sources.

Jan 1, 1962

By Charles Findlay

As one of its projects for degasification of major panels of coal prior to mining within them, the Bureau of Mines conducted methane emission studies during development of a set of three headings 1,800 feet in a major coal panel (2,700 by 3,500 feet) which had been completely isolated by sets of main headings for 12 months in the Federal No. 2 mine (Pittsburgh coalbed) in northern West Virginia. Similar emission studies were conducted in the development of two sets of main headings in virgin coal areas nearby. Comparing the two sets of data indicated that the isolated coal panel had been degasified by approximately 70 percent.

Jan 1, 1973

By James D. Eklund

Towards the goal of improving safety, economy and efficiency of scaling in underground metal/nonmetal mines, Battelle developed a combination prying/hammering scaling tool. A prototype was subjected to limited testing 1) to verify its operational functions and 2) to assess its potential capability in future underground testing.

Jan 1, 1983

By Jerome Apt

This manual has been prepared fur the help and guidance of underground coal mine operators. It details both common and unique engineering methods by which the respirable dust, which is generated in coal mines, can be controlled. This document was compiled by Apt, Bramer, Conrad and Associates, Inc. under contract number H0111464, issued by the U. S. Bureau of Mines and forms Volume II of the final report. This contract was authorized by and executed pursuant to the Federal Coal Mine Health and Safety. Act of 1969 (P. I. 91-173; 83 Stat. 742).

Jan 1, 1972

By Jules Gordon

Presents the results of mining tests conducted on a forward rotating bucket wheel excavator designed to continuously mine coal at 1080 tons/hour, Goals of the program are to determine the feasibility of the forward rotating bucket wheel principle as an effective means of reducing fragmentation and loading costs associated with surface mining, with additional benefit in reducing, coal preparation costs and stripping overburden. Tests took place at the Navajo Mine in Fruitland, New Mexico, Results show that the excavator performed as expected and can reduce fragmenting and loading costs up to 80°. Presented are: 1) production machine design specifications and projected economies extrapolated from the test data, and 2) recommendations for further work in dust control.

Jan 1, 1977