Search Documents

By J. Koster

[Boron is an element whose metallurgical possibilities never have been investigated thoroughly, probably because of the difficulties experienced in the preparation of elemental boron and its intermetallic compounds. The southwestern United States contain the world's s largest deposits of boron minerals. In general, the mineral is readily available, and mining costs are not excessive. The most important boron mineral of commerce is borax (sodium tetraborate) however, there are large deposits of colemanite (a mineral having the composition represented by 2CaO 3B2O3 5H2O) in Clark County, Nov. This material was worked in times past by converting it to sodium tetraborate. In recent years the deposits have laid idle because of a mire readily available source of borax in the old lake beds of California.]

Jan 1, 1940

By Linneas W. Laage

MFIRE is a computer simulation program that performs normal ventilation network planning calculations, and dynamic transient state simulation of ventilation networks under a variety of conditions. The program is useful for the analysis of ventilation networks under thermal and mechanical influence. MFIRE simulates a mine's ventilation system and its response to altered ventilation parameters, external influences such as temperatures, and internal influences such as fires. Extensive output enables detailed quantitative analysis of the effects of the proposed alteration to the ventilation system Network simulation using digital computers has become widespread throughout the mining industry in recent years. However, as the sophistication of the simulator increases (MFIRE, for example), the complexity of input data requirements and interpretations of results requires more skill and knowledge from the users. Perhaps the most difficult part of using MFIRE is to construct the data set describing the mine's physical layout and its ventilation properties. The initial attempts to get the data set running often reveal unknown or ignored aspects of the mine's ventilation.

Jan 1, 1995

By Loren R. Anderson

Traditionally, an evaluation of the safety of slopes has been based on computing a safety factor against failure. In computing the safety factor, the geometry of the slope, the soil parameters and the pore pressures are treated as deterministic quantities even though they are known to be random variables. A pseudo-three-dimensional probabilistic slope stability model has been developed that treats shear strength as a random variable. The model uses the probability of a slope failure as an assessment of slope reliability. The model can accommodate zoned embankments of soil in which the strength is described by the Mohr-Coulomb strength envelope. Autocorrelation functions are used to describe the spatial correlation of the strength parameters, c and tan ø. Model error can also be included in the analysis. The model has been applied to an existing tailings dam and to several hypothetical examples. These examples are presented to illustrate the influence of the choice of the soil strength variability parameters on the probability of failure. The results show that the critical failure surface based on the minimum safety factor is not necessarily the failure surface that will yield the maximum probability of failure. The analysis of the tailings dam shows that variance reduction can be large and that the model error is the dominant source of uncertainty for the embankment analyzed.

Jan 1, 1982

By James E. Cairelli

The NASA Lewis Research Center, under U.S. Bureau of Mines program direction, performed an assessment of alternative mobile power sources for mining applications. A wide variety of heat engines and energy systems was initially examined to ascertain which could be considered as potential alternatives to presently used power systems. The present mobile power systems are electrical trailing cable, electrical battery, and diesel - with diesel being largely limited in the United States to noncoal mines. Each candidate power source was evaluated in terms, of the following requirements: (1) Ability to achieve the duty cycle (2) Ability to meet Government regulations (MSHA certification) (3) Availability (production readiness) (4) Market availability (5) Packaging capability An initial screening reduced the list of candidates to the following: (1) Diesel (2) Stirling (3) Gas turbine (4) Rankine (steam) (5) Advanced electric (batteries) (6) Mechanical energy storage (flywheel) (7) Use of hydrogen evolved from metal hydrides This list of candidates was divided into two classes of alternative power sources for mining applications - heat engines and energy storage systems. A summary of each class follows.

Jan 1, 1981

By William H. Hamilton

This report describes the results and conclusions of the development and evaluation of a unique concept for a lightweight air powered drill tool for probe drilling in anthracite mines. A concept model of the lightweight air powered tool was constructed and evaluation testing conducted at the Kocher Coal Company Porter Tunnel Mine. The unique anchoring method proved to be extremely satisfactory and the overall light-weight air powered drill tool concept proved feasible. Based on the results of the concept model testing, two prototype production units were designed and manufactured. These prototype units proved to meet all of their design requirements of lightweight, portability, drilling controllability, structural integrity and miner acceptance. The need for a better bit and drill steel system, however, became evident during the testing program and recommendations are made for further investigation and development of a bit and drill steel system suitable for this application.

Jan 1, 1979

By T. M. Barczak

A primary objective of the Bureau of Mines geomechanics research program is to develop a better understanding of support behavior and interaction of supports with the strata so that supports can be more closely engineered to the geological conditions in which they are employed. Four longwall shield supports were instrumented with an eight-transducer instrumentation array to measure leg, canopy capsule, and compression lemniscate link forces from which resultant shield loading was determined. The instrumented supports were monitored over a 4-month period, producing over 75 shield cycles of resultant shield loading. Resultant loading is the true measure of support resistance, providing both roof-to-floor and face-to-waste support reactions as well as the location of the reaction on the shield canopy. Observed roof support reactions were analyzed, with particular emphasis on horizontal shield loading, since it is the least understood design parameter. Average, peak, and change in shield loading during the mining cycle are discussed. Correlations among data parameters are examined, as is the distribution of support loading at the headgate and midface. Conclusions are drawn as to the effectiveness of the shield support at this installation. Recommendations are made for further research needs.

Jan 1, 1987

By Donald R. Johnson

Apparatus providing simultaneous differential thermal analysis, thermo-gravimetry, and evolved gas analysis, has been developed by the Bureau of Mines specifically for thermal study of oil shale and other solid, natural fuels. The apparatus is described in detail, and simultaneous analyses on a single sample of an oil shale mineral, nahcolite, and a thermal analysis demonstration compound, calcium oxalate monohydrate, are presented to demonstrate the instrument's capabilities.

Jan 1, 1970

By E. Shekarchi

A year after the Soviet Union invaded Afghanistan and replaced President Amin with their choice, President Karmal, Afghanistan remained in turmoil. In some respects, the political and economic situation in Afghanistan was no better by the end of 1980 than it was preceding the December 1979 invasion. The Government faced widespread and growing alienation and resistance, virulent factionalism within the ruling party, and an acute shortage of material. The mining sector of the country did not fare better either; the only raw material produced in a significant amount was natural gas, which was exported mainly to the Soviet Union. No statistics on production of other minerals and materials were available by yearend. Most of Afghanistan's gas production was from the Hodja-Gugerdag Field, southeast of Shibarghan. The gas flow from this field had been about 300 million cubic feet per day since 1961. An estimated 230 to 250 million cubic feet per day of Hodja-Gugerdag's production was moved by pipeline across the Amu-Darya River into the Soviet Union. Most of the remainder was transmitted eastward to a 105,000-ton-per-year fertilizer plant and an electric power station built near Mazar-i-Sharif with Soviet assistance. After the Soviet invasion, the second gasfield, Djar-Kuduk, in the Shibarghan area, was brought under production. This field, which will produce about 200 million cubic feet per day, consists of four gas zones in the Jurassic and lower Cretaceous zones between 3,000 and 8.500 feet deep. The gas has a high hydrogen sulfide content, with considerable carbon dioxide, A new treatment plant was built at Djar-Kuduk by Soviet technicians under a turnkey contract at the end of 1980. It is believed that most of the Djar-Kuduk's initial flow will be sent to the Soviet Union.

Jan 1, 1982

By Charles E. Whieldon

Because of the importance of recovering more oil from known petroleum reserves, increased emphasis has been placed on the application of secondary-recovery methods. It is hoped that these reports will stimulate interest in improved waterflooding techniques, thereby discouraging premature abandonment of oil leases. Previously published reports3 4 5/ have described the results of water-flooding in Roane, Pleasants, and Wetzel Counties, W. Va. (fig. 1). This report describes the South Penn Oil Co. Yawkey waterflood property, Berea sand, Griffithsville oilfield, Duval District, Lincoln County, W. Va. (fig. 2).

Jan 1, 1961

By Dean H. Ambrose

This paper presents the results of a study using computer human modeling to examine machine appendage speed. The objective was to determine the impact of roof bolter machine appendage speed on the likelihood of the operator coming in contact with. A contact means two or more objects intersecting or touching each other, e.g., appendage makes contact with the operator?s hand, arm, head or leg. Incident investigation reports do not usually contain enough information to aid in studying this problem and laboratory experiments with human subjects are also not feasible because of safety and ethical issues. As an alternative, researchers developed a computer model approach as the primary means to gather data. By simulating an operator?s random behavior and machine?s appendage velocity, researchers can study potential hazards of tasks where it is not possible to perform experiments with human subjects. Analysis information is helpful to the mining industry in terms of making recommendations that reduce the likelihood that roof-bolter operators experience injury due to contact with a moving boom. Data analysis of roof bolter simulations show that the virtual-operator?s response time has little effect on the number of contacts experienced. Based on frequency and cross-tabulation, regardless of other variables, contact incidents were always greater when the boom was moving up, were always greater on the palm, and were always greater for the boom part of the machine. Also, regardless of boom speed, the 25th-percentile-sized operators experienced more contacts than did other operator sizes. Furthermore, regardless of boom speed, the 152-cm mine seam experienced more contacts than did other seam heights tested. Results of a survival analytic approach suggest that controlling the boom speed is the most important factor in determining the risk of an operator making contact. Based on the data collected, boom speed greater than 41 cm/s results in a substantial increase in risk to the roof bolter operator and should probably be avoided. At speeds less than or equal to 25 cm/s are associated with a more modest relative risk, which represents an acceptable level of risk. Also, at speeds between 25 and 41 cm/s, there could be a particular boom speed in this range at which a significant inflection point in the relative risk estimates occurs. Based on the results, this issue needs to be addressed by future research.

Jan 1, 2003

By Peter de Bakker

The objective of this contract was to develop a simple, reliable, economical, remote-control roof bolting module for installation of mechanical and resin bolts. It was to be capable of placing longer than seam height bolts, up to 10 ft lengths, from a seam height of 36 to 72 in., while keeping the operator under supported roof. The resulting machine, called REM-Bolter, is a low profile unit that utilizes Foster-Miller Flexible Shaft Roof Drill, a Bendix Roof Bolt Inserter and a newly designed. Roof Bolt Lifter/Torquer. Every effort was made to strike a compromise between complete automation and complete manual control. In a controlled laboratory environment the REM-Bolter remotely installed 1000 bolts. Subsequently the machine was tested in an operating coal mine where 500 holes were drilled (and an equal number of bolts were installed) remotely, over a 4 month period. The results of all tests Live shown that the operator of a machine of this kind can quickly, and repeatedly, install rootbolts remotely from his operator compartment some 8 ft away from the drilling/bolting action. The report includes recommendations for improvements to the present REM-Bolter design that would translate the present test bed into a second generation test bed and a potential first generation production unit.

Jan 1, 1983

By Peter Swanson

One of the primary methods for analyzing roof stability in underground mines is the age-old method of “roof sounding” where a miner taps on the roof and listens for the hollow sound of loose blocks of rock. This paper looks at the feasibility of using noncontact laser-based vibration measurements to detect roof fall hazards with the ultimate vision of improving, expanding and automating procedures for mine roof inspection. Vibration measurements made on loose blocks of rock in underground mines are summarized and compared to estimates of fundamental resonance frequencies for rock slabs of the size responsible for highly hazardous “skin failures.” Both laser Doppler vibrometry and full-field interferometric methods are examined and are considered to be feasible methods for detecting anomalous vibrations in loose roof rocks. Results from simple laboratory experiments using laser vibrometry demonstrate some of the proposed application concepts. While considered a challenge to move these techniques from the laboratory to heavy industrial or outdoor environments, the potential for success in the current application is enhanced by the reduced requirements of qualitative analyses.

By C. D. Messelt

The Bureau of Mines investigated the application of a diffusion model to sintering rate data developed for lithium titanium ferrite. The data were obtained by sintering pressed pellets under identical conditions for various times up to 11 hours. Stereological measurements were made on polished sections, and sintering rates were calculated. A model for intermediate stage sintering was fitted to the stereological data. This procedure produced a method by which these type data could be used to study the relative importance of volume and grain-boundary diffusion under a variety of sintering conditions.

Jan 1, 1979

Provide optimum visibility of mining operations while maintaining protection and comfort for ma-chine operators. Approach Cabs and canopies with hydraulically powered variable-height control were developed for several machines and tested in underground mining operations. How It Works From his position in the cab, the operator can raise or lower the cab, selecting a height that offers either more visibility of the working place or greater clearance for tramming. The entire cab enclosure moves up and down on guide rollers that ride on a pair of rails, and is actuated by a hydraulic cylinder controlled from within the cab. Normal working heights, for each of the four different cabs developed, are with the cab bottom from 6 to 8 inches above the mine bottom. A typical range of elevation (excursion) afforded by this design is shown in Figure 1.

Jan 1, 1978

By M. P. Board, J. K. Whyatt, T. J. Williams

The U.S. Bureau of Mines has been conducting a series of rock mechanics investigations at the Lucky Friday Mime in the Coeur d'Alene Mining District of northern Idaho. In the present study, the energy release rate (ERR) index was used to evaluate three underhand stope backfill parameters--cement content, density, and placement gap-to determine their influence on rock bursts. This index provides a relative measure of the likelihood of rock bursting for a given rock mass. It is known that the elastic idealization of the rock mass inherent in this method causes underestimation of stope closure and hence underestimation of the influence of backfill on rock bursting. However, this evaluation still showed that (1) changing from present practice to one in which backfill was omitted altogether would increase the ERR by 42 pct and (2) perfect placement of backfill would reduce the ERR below present practice levels by 28 pct. The easiest step toward perfect placement would be elimination of the placement gap, which accounted for half of the difference in ERR between present practice and ideal placement conditions. There was no indication that increasing initial fill strength through increased cement content would affect the ERR.

Jan 1, 1992

By R. J. Leary

The technologies of contemporary iron and steel production and of direct reduction processes have been studied to identify and estimate the potential effects of direct reduction on mineral consumption and the problems raised thereby for the Nation's mineral supply to the iron and steel industry. Contemporary patterns of mineral raw material and energy consumption were determined from a study of the 1964-70 period. Major changes were observed in requirements for 14 of 20 principal commodities. Average practice in 1970 was compared to best practice to estimate the potential effects of implementing existing technology without recourse to direct reduction. Potential effects of direct reduction were estimated by comparing the mineral requirements for 95 percent reduced pellets with 1970 best practice technology for two cases of use: (I) complete substitution for hematite pellets in blast furnace burdens, and (11) partial substitution (40 percent) for scrap in electric furnace steel charges. Effects upon mineral supplies are described; important collateral factors are analyzed, and the principal metallurgical, industrial, and environmental consequences of implementing direct reduction are discussed. Major effects of direct reduction on the domestic steel industry and its mineral supply system are foreseeable. Direct reduction will (1) create a large demand for low-gangue iron ore; (2) relieve the dependence of the steel industry on coking coal, and (3) permit great increases in furnace productivity, both in blast furnace ironmaking and electric arc furnace steelmaking.

Jan 1, 1973

By John Organiscak

A majority of continuous mining machines employ a water spray system and a machine mounted flooded-bed scrubber to suppress and capture dust during coal mining. These machine mounted dust control systems must be designed to function within the localized face ventilation system at the mining section to control both dust and methane. Spray systems can impede or improve the scrubber effectiveness in controlling dust or methane at the mining face. Laboratory experiments were conducted to examine the effect of spray type, spray pressure, machine body blocking sprays, and scrubber airflow on dust and gas levels while using a 12.2 m (40 ft) exhaust ventilation curtain setback from the face. These experiments were conducted with the mining machine positioned at the end of a simulated 6.1 m (20 ft) sump and slab cut. Results indicate that the hollow cone nozzles with blocking sprays best complemented the flooded-bed scrubber performance in an exhaust ventilation system. This external spray system notably reduced dust and gas levels on the off-curtain side of the mining machine for both the sump and slab cut as compared to the flat spray nozzles. Higher scrubber airflows reduced dust and gas levels on the curtain side and in the return of the continuous mining machine. The remote operator position, located on the off curtain side and parallel to the inlet end of the exhaust curtain, sustained the most stable and lowest dust levels around the mining machine.

Jan 1, 2010

To provide cooler air to miners working in hot areas of mines, particularly new deep hardrock mines. Approach Air supplied to hot working areas of mines is cooled by passing it through a series of water sprays. How It Works Water nozzles mounted inside a section of ventilation tubing release cooling sprays of water into the air being blown through the tube. The prototype of the water spray cooler consists of six evenly spaced water sprays located inside a 10-ft. long section of 16-inch-diameter fiberglass ventilation tubing. See diagram. This section of rigid tubing is installed into one of the positive pressure ventilation tubing lines that conduct fresh air into working stopes. The intake manifold to the six water sprays is connected to the mine?s cool water line, and the water valve on the manifold is opened. Warm ventilation air being supplied to the stope passes through the water sprays, and is cooled by the lower temperature water.

Jan 1, 1979

By Robert L. Lappi

Eight interburden handling concepts are developed for multiple seam area mine stripping operations in central and western United States. They are based on data gathered and analyzed during field surveys, literature reviews and visits to state requlatory agencies in five states. It is concluded that improvement of reclamation practices through selective interburden handling techniques is possible at lower operating costs than currently incurred. Specific multiple seam mining systems are discussed in this report.

Jan 1, 1980

By C. J. Bise

One area of study for the Coal Mine Injury Analysis project was to illustrate how loss control can be used as a foundation for mine safety training. After an initial review of the principles of loss control, the instruments often used for worker/worksite appraisal, such as incident reporting, analysis, and investigation, workplace observation, worksite inspection, and safety audits and checklists were evaluated for their effectiveness. The findings were then applied to the continuous-miner worksite at several mines to modify the techniques for use in a highly dynamic man/machine work environment. Before the information gathered from the review of the various continuous-miner worksites was presented at the annual retraining sessions at five mines, a trainability analysis procedure was developed to separate training shortcomings from those problems resulting from improper equipment design or unsatisfactory working environments. Also, several microcomputer-based training programs were developed to aid in conveying the loss-control concepts to the trainees. Finally, the results from the implementation and evaluation of the loss-control-based training programs were documented, including the complete training script for one of the case-study mines. The procedures outlined in this study will aid mine training specialists in developing focused, pro-active accident-prevention strategies and training programs that are based on sound loss-control principles.

Jan 1, 1993