Search Documents

By Jeon Jeon, Yong-Kun Choi, Chung-In Lee, Yong-Hun Jong, Hag-Soo Kim

In this study, a computer program to design tunnel blasting pattern has been developed. The program consists of two parts; one is for tunnel blasting pattern design and the other is for blasting modeling to estimate the peak particle velocity, the distribution of fragmentation and the excavation damage zone. We modified the design method of tunnel blasting pattern suggested by Langefors because it provided undesirable pattern in blasting practices such as considerably large center cut and too large burden for Vcut as drilling length increased. As a result, the burden and spacing were reduced to practically appropriate amounts. In addition, the correlation between rock mass rate, RMR, and rock constant in blasting, c, was analyzed based on the data collected from twenty three tests of tunnel blasting. It was concluded that the correlation between them was fairly good enough to be applied in cut design. In order to check the validity of the modified methods and their practical applicability, test blasting was carried out at two different tunnel construction sites in Korea. The results were satisfactory in that the average rate of advance was 90% and the overbreak did not cause additional support. Futhermore, the developed program is capable of estimating peak particle velocity by using (a) the existing vibration equations, (b) the vibration equation obtained by test blasting to check out the practical applicability of the designed blasting pattern. Feedback is implemented into the program to adjust the designed blasting pattern and control the vibration.

Jan 1, 2005

By Adam Gray, Emery Gray

State-of-the-art seismographs can be employed to assist the blasting engineer in understanding the propagation of vibration waves generated by blasting. Wave traces and frequency plots are used to adjust shot loading and timing, especially around close or near- field structures. Successful close-in blasting vibration monitoring requires careful consideration of the following: Geophone locations Mounting of geophone both on structures and in the ground Differences between ground motion and structural response This presentation will discuss methods used to control and monitor blast-induced ground and structure motions. Case histories are presented to illustrate seismic monitoring used as a tool to control vibrations and guide the blaster in the design process.

Jan 1, 2005

By Brian Stump, David Anderson, D. Craig Pearson, Robert Martin

Mining explosions designed to move, bulk or fracture rock are often composed of a number of explosions arranged in a complex spatial and temporal pattern. The effects of the explosions are strongly dependent upon the design and implementation of this blasting pattern. This paper describes the collection, combination and visual display of multiple types of data from these explosions for the purposes of understanding the relationships between the blast design, implementation, and observations. Data sets consist of three-component ground motion, acoustic, video and high speed film, three-dimensional topography, geological and geophysical properties, design blast pattern and timing, and velocity of detonation in the explosive for individual borehole detonation times. The explosions studied include simple single-fired contained explosions, ones designed to bulk and fracture rocks and those that cast material.

Jan 1, 2000

By Gungor Tuncer, Ali Kahriman, Abdulkadir Karadogan, Mehmet Aksoy, Kagan Ozdemire

With increasing environmental constraints on the levels of disturbance induced by blasting operations upon nearby residents, there is an increasing need to be able to design cautious blasting with greater precision. Therefore, determination of maximum amount of explosive per delay for a certain distance especially in large blasts is of great importance for the elimination of these environmental problems. Although too many research studies had been carried out in the past in order to eliminate environmental issues produced from blasting unfortunately a general approach or formula has not been established yet because of the complexity of the matter. In addition to the wave and ground motion characteristics, the complexity of blasting parameters and site factors restrict the developing a general criterion. So experimental site-specific studies should be still done in order to predict and control blasting effects. This paper presents the results of ground vibration measurements carried out in Espey Open-Pit Boron (Colemanite) Mine located on the west side of the central Anatolia near Kütahya province in Turkey. Within the scope of this study, ground vibration components were measured for 13 shots during bench blast optimisation studies in order to predict peak particle velocity level for this site. In blasting operations; ANFO and Powergel Magnum 600 (blasting agent), Powergel Magnum (priming) and delay electric detonators (firing) were used as explosives. Parameters of scaled distance (charge quantity per delay and the distance between the source and the station) were recorded carefully and the ground vibration components were measured for all blast events using 4 different types vibration monitors (3 White Mini-Seis and 1 Instantel Minimate Plus Models). Then, the data pairs of scaled distance and particle velocity obtained from the 38 record events were analysed statistically. At the end of statistical evaluation of the data pairs, an empirical relation which gives average line at 95% confidence level and upper bound 95% prediction line with a reasonable correlation coefficient was established between peak particle velocity and scaled distance.

Jan 1, 2005

By Sam Kangwa, Thomson Sinkala

In the mining industry, drilling accuracy has a significant effect on the economy of operations. In this paper, results from the Nkana Division of the former Zambia Consolidated Copper Mines are presented. For the stope investigated, it was found that the extra operational costs alone were 462% of the planned costs! Clearly, there is more than good reason to pay attention to drilling of good quality holes.

Jan 1, 2004

By John Capers

•The IME is the Safety and Security Association of the commercial explosives industry in the United States and Canada. •Founded in 1913 •Board of Governors •5 Standing committees- 1. Technical 2. Environmental Affairs 3. Legal Affairs 4. Safety & Health 5. Transportation & Distribution

Jan 1, 2006

By Rob Farnfield, Charlie Adhock

The measurement of near-field shock has always been an attractive proposition for those working in the field of explosive and blast performance. The most commonly employed technique involves the use of piezoelectric accelerometers. Although highly effective, these complicated devices are relatively expensive and are often destroyed in the blast event. This paper describes the development and field-testing of a shock sensor of sufficiently low cost to enable it to be routinely used in product blasting. This new device is based on piezoelectric wafer technology and does not require any external signal conditioning. The device is housed in a small cylindrical package with approximate dimensions of 30mm (1.2”) length and 5mm (0.2”) diameter. It has been determined that the most effective way of fixing the device to rock is in a small diameter hole with epoxy glue. Alternatively the sensor can be simply placed in holes filled with either water or bulk emulsion explosive.

Jan 1, 2005

By Jim Mikelait

Overview ?? Why do we need security? ?? Needs assessment ?? Elements to any security system ?? Protect, Detect, Alert, esponse ?? Electronic Security System Criteria ?? Advantages and Limitations of Various Security Options ?? Internal measures to protect against potentially harmful employees ?? How can technology improve my business?

Jan 1, 2006

By Ajoy K. Singh, B Mohanty, P K. Singh

A study was conducted to investigate the damage potential to underground multiseam openings caused due to vibration generated by open-pit coal mine blasting. The objective was to recommend optimal explosives weight per delay to be detonated in open-pit blasts to ensure the safety and stability of underground openings. Sixteen blasts with varying charge weights and initiation sequences were conducted at Samleshawari open-pit mine and eighty four blast vibration data were recorded in the Hingir Rampur underground colliery in India. Analysis of vibration data showed that roof of the underground openings vibrated with much higher amplitudes compared to those in pillars and floors. The amplifications of vibration in the roof at the junction were upto 4.3 times the pillar vibration. It was observed that coal chips detached from roof when the peak particle velocity reached 131 mm/s or higher. The vibration magnitude recorded was higher in upper-seam openings than in belowseam openings. Rapid attenuation of vibration was recorded in below-seam openings at similar locations. Appropriate particle velocity-charge weight-distance equations were established to calculate the safe explosive weight per delay to be detonated in open-pit mine for the safety of multi-seams workings of underground mine. The support for the galleries and junctions were further modified for the working seams to ensure greater safety.

Jan 1, 2011

By Charles Pretorius, Henk Ludik

Navachab Mine experiences difficulties with pit wall stability in certain areas of the mine. The main reason for the instability is the fact that the geology comprises many joints and faults. Blasting, without impacting negatively on the stability of the pit walls, poses a major challenge.

Jan 1, 2006

By Michael S. Wieland

This report focuses on the U.S. Bureau of Mines research regarding desensitization and malfunction of delay detonators and cap-sensitive explosives. Delay blasting in underground coal generates tremendous shock waves and rifting forces that fracture and heave coal. The shock waves from charge explosions radiate outward in all directions through the coal, impacting neighboring charges with later delays. The impact phenomena have debilitating effects, causing degrees of reduced charge performance ranging from misfires or weak detonations to out-of-sequence detonations. Impaired charges react poorly, fracture less coal, and produce fumes with higher toxicity. Coal-mine, underwater, and simulator tests were conducted to more thoroughly understand the shock damage mechanism. Recently the U.S. Bureau of Mines partially resolved the malfunction problem by demonstrating the feasibility of formulating a rugged explosive. This rugged cap-sensitive candidate passed the requisite tests for certifying an underground coal-mine explosive. With natural aging the formulation rapidly lost initiation sensitivity. The charge formulation had to be rebatched to finish the testing and therefore could not be certified.

Jan 1, 1992

By Paul Worsey, Larry Frost, Braden Lusk, Seok Bin Lim

For certification of blast resistant windows, current tests consist of arena tests or large air gun tests. Arena tests involve the detonation of more than 1000 pounds of explosives with windows placed in the range of hundreds of feet. The result of an arena test is a loading on a window consistent with an expected industrial or terrorist blast. Due to the nature of this type of test, only a limited number of facilities are available and operational costs can be extremely high. Air gun tests involve the use of compressed air and a failing diaphragm fired through a large tube. Although this test is more cost effective and easier to administer with lower environmental impacts, it is not an explosive loading and does not create a negative phase on the tail of the pressure pulse. Simply using a small charge in close proximity to the window is not a viable option either. The pressure peak can be reached using this method, but the duration of the pressure pulse is such that the positive phase impulse is on the order of ten times less than that for an arena test.

Jan 1, 2006

By Darren Thorton, David Sprott, Ian Brunton

Blasting causes movement of the rock and can be detrimental to the accurate delineation of the ore and waste regions within the resulting muck pile. The consequences can be ore loss and dilution. However, ore loss and dilution can be minimized and significant increases in profit can be realized if the movement can be accurately measured. Various methods have been used to measure muck pile movement including poly-pipe, chain and sandbags but these have been either inaccurate or impractical. The Julius Kruttschnitt Mineral Research Centre, JKMRC, has developed an electronic blast movement monitor that provides accurate three-dimensional movement vectors following a production blast. From this information, the ore block boundaries in the blasted bench can be adjusted to compensate for the measured movement and then ore recovery can be optimised. Following initial development of the prototype technology, the JKMRC further developed and demonstrated the system in actual production blasts at an open pit gold mine operated by Placer Dome Inc.

Jan 1, 2005

By Larry Schneider

I n the simplest application of a shock tube initiation system, the tubing acts as a “relay line” which passes a detonation signal from borehole to borehole. When the signal arrives at each borehole, it causes the detonator attached to it to fire. Such a single path constitutes a progressive series where each unit must function properly in order to activate the following units. Any application error, malfunction, or mistake in connecting any surface unit will stop the progression of the detonation signal through the system and result in a “cutoff” or misfire of the following charges.

Jan 1, 1995

By Thierry Bernard, Guy Gagnon

Blasting at very close proximity to urban areas is typically a situation where both local communities and mining stakeholders get nervous. The context becomes logically even more tensed when the blasting operations have to be performed above an old underground mine. When mitigating subsidence risks requires firing the largest possible shots, the nuisance control (flyrock, vibration, and noise) required by local and national regulations, contrarily urge for being more conservative.

Jan 1, 2014

By T Goswami

The conventional practice in open cut coal strip mining has been to blast the overburden or coal layers in separate blast events. This is done in order to maximise the benefits from throw blasting and also to limit coal losses. Each blast event usually has a particular design of hole diameters, burdens and spacings, explosive charges and blast timing in order to achieve the required blast outcome for either the overburden or coal. This means that each blast has to be separately cleaned on the surface after excavation of the previous blast. Hole locations then have to be individually surveyed and marked, holes drilled, explosives and initiators loaded and the blast fired. Each of these actions takes considerable time and resources and therefore impacts on mine productivity. The mine has to be cleared for each blast event and every blast presents a new potential source for noise, dust or vibration disturbance to the neighbouring population. Exposed highwalls are also subjected to vibration and damage from each subsequent blast event

Jan 1, 2006

By W. J. Birch, R. Farnfield, L. Bermingham

Whilst a significant body of research has been carried into air overpressure levels that arise as a result of the use of explosives, few published studies have actually tried to relate the movement of a quarry face to the resulting air overpressure produced. The aim of this preliminary investigation was to monitor a number of quarry blasts at two different limestone quarries. The first using multiple separately initiated deck charges in a multi borehole blast, the second using single column charges in a multi borehole blast.

Jan 1, 2008

By Dale Preece, Steven Sobolik, Richard Jensen

Recent events demonstrate that civil and government facilities and structures face an ever-increasing need to be designed for protection against malevolent explosions. Modification of existing public structures and especially design of new ones increasingly includes provisions for explosive protection. ISEE members endorse and promote responsible application of explosives to benefit mankind and deplore any other use. However, our knowledge of explosive behavior and our ability to predict the results of explosive events puts us in a unique position to give guidance to designers of civil and public structures. Recent advances in computational methods have resulted in new computer codes with ALE (arbitrary lagrangian eulerian) simulation capabilities. Historically, lagrangian computational methods have been used for modeling solids because the mesh or discretization moves with the material. Rock breakage resulting from explosively induced shock-waves has been successfully modeled with lagrangian codes. Explosive detonation has traditionally been modeled with eulerian techniques. Eulerian methods have been used to model gases and fluids, tracking the material as it moves through the computational grid. ALE computational technology couples the two methods together in a manner never before possible. An ALE simulation can accurately treat the explosive detonation, interaction of explosive gases with air, and the impact of explosive event on nearby solid structures. ALEGRA (Budge et al. 1997 a & b) is an ALE code developed at Sandia National Laboratories. ALEGRA simulations accurately predict the explosively induced impulse on the structure to be protected. It has been applied to the analysis and design of blastwalls to protect structures and people from explosive events. The impulse calculated can be used by structural engineers to design a blastwall. ALEGRA has also been applied to predict the effect of a blastwall on explosion overpressure some distance behind the blastwall to assess the effect on people present during the event.

Jan 1, 2000

"The objective in controlled blasting is to reduce overbreak to control the final pit wall slope, shaft, drift ditch, bench, etc. to the final planned excavation limit. The six main types of controlled blasting utilized today are:1. Line Drilling2. Cushion Blasting3. Smooth Wall Blasting4. Buffer Blasting5. Presplitting or Preshearing6. Air Deck Presplitting"

Jan 1, 1994

By Jun Yang, Zongshan Zou, Mei Qu, Jianjun Zuo

For technical renovation of the thermal plant, one frame structure workshop of 50,000 m2 (59,800 yd2) construction area and one reinforcement concrete chimney of 150m (492 ft) height shall be demolished by blasting at same time. The engineering environment of which is complicated and the accommodation space is limited. Therefore, the collapse sequence, direction, scope of the dismantled building must be accurately controlled to ensure the safe operation of the adjacent generator unit and transformer station. By taking technical measures of theoretical analysis and numerical simulation etc., as well as research on structures collapse method and detailed delay interval, it puts forward the technology of bidirectional folded collapse of the workshop and it uniquely adopts the initiation system that combined with “half-second delay inside drilling” and “millisecond delay outside drilling”. Additionally, by using of the integrated vibration reduction technology in combination of the blasting ruins, buffer ditch and damping ditch, it has safely accomplished the demolition blasting work in high efficiency. Besides the demolition blasting vibration signal is collected and analyzed. The success of the demolition blasting will become valuable reference to other similar works.

Jan 1, 2016