Search Documents

By Z. G. Song, C. Y. Sun, X. R. Zhang, Y. Yu

In skarn type scheelite deposit, there are calcium minerals with floatability similar to scheelite, such as calcite, fluorite, etc., which are difficult to separate. Heating cleaning method developed by Petrov has been widely applied in processing rough concentrate of scheelite for nearly half a century, but there exists a general lack of full understanding of the interaction between floatation reagent and mineral particles surfaces. The mechanism on separation of scheelite and calcium minerals in heating cleaning process was investigated by mineral flotation experiments, XPS analysis, as well as solution chemistry and crystal chemistry calculations. The results showed that the sequence of minerals floatability using sodium oleate as collector and a large amount of sodium silicate as modifier in heating flotation test was scheelite > calcite > fluorite, which was the same as solution chemistry calculations based on Gibbs free energy vs. pH and also the same as Ca-X intensity order by crystal chemistry analysis. There are two sides about the mechanism of heating cleaning method: one is that the adsorbed collector on calcium minerals surface is desorbed more easily than scheelite, and the other is selective dissolution of calcium ions from the mineral surface because of Ca-X intensity difference in heating and stirring process.

Jan 1, 2014

By Héctor X. Toro, José Francisco Cabello, Douglas Batista, Álvaro Videla, Claudio Luiz Schneider

The Minas-Rio Project, located in the state of Minas Gerais, Brazil, is currently under construction. The new plant will have a regrinding circuit that uses VertimillTM. The objective is to process itabirite iron ores and it is expected that the consumption of media will represent a large part of the plant operating cost. Many studies in the literature indicate that the size of the grinding media directly influences the grinding efficiency. The size distribution of the charge media is related to the surface area of the charge. In this study, a sample of itabirite iron ore was tested with respect to grindability in a laboratory scale ball mill. The test mill was equipped with a torque device to accurately measure power consumption, as required for the determination of energy specific kinetic parameters. Five tests were carried out with different sizes of steel balls and with SICAM (sub-inch Cast Media). The size distributions of the feed and product of the several grinding tests were used to calibrate population balance model parameters for each condition. The results confirmed that the ball charge with smaller diameter is the most efficient among the different media charge tested.

Jan 1, 2014

By W. G. Liu

Phenyl malonic acid (PMA), a new chelating collector, which contains a phenyl structure and a malonic acid chelating group, has been synthesized and its collecting capabilities to calamine, hematite, quartz and hemimorphite are also studied in laboratory. From the experimental results, it can be seen that the PMA has somewhat flotation ability to calamine, hematite and quartz, while it nearly has no collecting ability to hemimorphite. With the increase of PMA concentration, the flotation recovery of calamine increases. When the dosage of PMA was 560g/t and at pH=7~9, the flotation recovery of calamine gets its maximum of 45.94%. The test results about the influence of pH on the flotation recovery of quartz show that the flotation recovery increases with the increase of pH, and the maximal flotation recovery can be gained in alkaline media. On the other hand, PMA has stronger flotation capability to hematite than to other minerals. The flotation recovery of minerals increases with increase of PMA concentration. When the dosage of PMA is 560g/t and at pH=5~7, the flotation recovery of hematite is 82.96%. Mean-while, the influence of pH on the flotation recovery of hematite was studied and test results showed that, as pH increases, the flotation recovery sharply rises until pH=4, then the increasing rate de-creases outstandingly, at pH=6 the flotation recovery reaches its maximum of 82.96% and it de-creases speedily in alkaline media. Finally, through the measurement of infrared spectroscopy and in terms of solution chemistry of collector, the flotation mechanism has been discussed. It was concluded that the adsorption of PMA on minerals surface is chemical adsorption in nature through two oxygen atoms in the polar group of phenyl malonic acid chelating with the metal ions of minerals surface to form a hexagon-cycle chelate complex: C(=O)-O-M-O-(O=)C.

Jan 1, 2014

By E. Gock

Based on the scientific investigations on mechanochemical synthesis of metal sulphides from metals or metal compounds and sulphur or sulphur compounds, the article describes the industrial production of nanoscale metal sulphides. Special operational conditions such as inert atmosphere, size and type of the grinding balls, grinding time and specific energy input are taken into consideration. A system configuration for the manufacturing of sulphides at a capacity of 100 kg/h is presented.

Jan 1, 2014

By T. Niedoba

The ash contents in coal particles were examined in the paper dependably on particle size and its density. So, the two-dimensional regressive function Z=Z(?, D) was the searched object, where Z is random variable describing ash contents, ? - density and D ? particle diameter. This dependence is determined basing on experimental data concerning the coal of type 31. For this coal, the method of ordinary kriging is applied to calculate the values of a random variable Z. This method requires the proper selection of so-called variogram function, which 4 forms are considered in this paper in purpose to select the best solution. The given results were then evaluated by the residual deviation value and so compared with empirical data.

Sep 1, 2012

By K. S. McClure, S. B. Chitralekha, R. B. Gopaluni, Chmylek. T., S. L. Shah

This is a tutorial paper on industrially successful approaches for nonlinear process monitoring. Online process monitoring is essential to continuous operation of plants at high efficiency. The problem of process monitoring is one where an impending but undesirable process condition has to be identified and used to alert process engineers. This problem has traditionally been solved by practicing engineers using statistical techniques that detect a change in the underlying correlation structure of process variables. For linear correlation structures, algorithms such as principal components analysis, independent component analysis and partial least squares have been proposed. However, many industrial processes exhibit nonlinear correlation structure between the process variables. In this tutorial we describe various nonlinear monitoring techniques and elaborate on two recently developed methods, namely Support Vector Machine and Local Linear Embedding. The two methods are evaluated by application on two experimental case studies, a SAG mill and a polymer extruder.

Jan 1, 2014

By A. V. Zimin

It is a well-known fact that usage of reverse cationic flotation in magnetite ores processing enables to improve the quality of magnetite concentrates. We designed an iron ore concentrate technology (with 70 -71 % of iron) including reverse cationic flotation in pneumo-mechanical flotators RIF (developed by RIVS Corporation, Russia) with good biodegradable etheramines as collectors for flotation of quartz. Practical application of high biodegradable flotation reagents decreases environmental impact risk of objects and enterprises of mining industrial complex. This work presents results of development of flotation technology for production of high quality ferruginous concentrates from magnetite ores of Russia and Ukraine deposits. Keywords: magnetite ores, reverse cationic flotation, ferruginous concentrates, pneumatic-mechanical flotation machines, environmental impact

Sep 1, 2012

By Kwan Ho Kim

In this study, free fall tests are conducted with the objective of understanding the breakage properties of waste concrete for the guide of the direction of the better comminution process. Waste concrete of 75mm×53mm is tested at various drop heights with or without heat pretreatment. Test results indicate that a block of waste concrete does not break by free fall, but eventually breaks by repeated free falls. The number of free falls required for complete separation of large aggregates from the cement mortar considerably reduced when the samples were heated at 400?. Therefore, a great energy saving can be obtained when heating the waste concrete prior to crushing. The energy saving was found to be dependent on the height of free fall but in all cases, was still large enough to offset the additional energy required for heating. Also, it was found that the heat pre-treatment gives an additional advantage in that it produced cleaner recycled aggregates. This may result from easier detachment of cement mortar from the aggregates due to weakening of bonding forces by heating. By analyzing the size distribution of the crushed product, a free-fall breakage model is developed using the particle breakage ratio and the breakage pattern. The developed model can be used to predict and to analyze waste concrete processing circuit.

Jan 1, 2014

By S. M. Bradshaw, R. Smith, J. H. van Vreden, C. A. Snyders

"The re-treatment of gold tailing heaps has shown to be a potentially significant revenue stream for both large and small scale gold companies. Limited access to capital and lack of skilled labour remain restrictive especially when dealing with a refractory ore and/or where limited amount of material are available. Alternative techniques such as low temperature pre-leaching options to unlock value are therefore in demand. Several low temperature pre-leaching experiments in acidic and alkaline solutions, followed by cyanidation were performed which ultimately led to the further investigation of a caustic pre-leaching step. It was found that the Au recovery from a refractory ore tailings heap could be significantly improved from ˜ 15 to 20% to greater than 60% with a simple atmospheric NaOH pre-leaching step. It was further considered, that since the NaOH pre-leach liberate the Au associated with refractory sulphide minerals, the overall process may benefit by the inclusion of a froth flotation step to separate refractory sulphides from the free milling ore. Froth flotation on weathered tailing heaps are, however, known to be difficult, ultimately resulting in poor recoveries. A process flow sheet, incorporating a caustic pre-leaching step and a process which includes flotation and caustic pre-leaching of the concentrate, are technically evaluated and ultimately compared to simple cyanide re-processing. INTRODUCTION South Africa consists of a large number of gold tailings dumps. Janse van Rensburg (2016) estimated that there was about 517 dumps in the Gauteng area, covering approximately 320 000 ha of surface area. Recovering value from the dumps has received a great deal of interest but can be problematic due to the dumps often being refractory, preg-robbing and weathered. High recovery of valuable metals (Au and Ag) are possible (Fleming and Brown, 2010) but would most likely require pressure oxidation and subsequent neutralisation which can be very capital intensive demanding a high skill set to operate and maintain. In addition, these flowsheets target high processing tonnages due to the economy of scales at the lower grade feed materials, further increasing the capital requirement."

Jan 1, 2018

By Nina Panteleeva, Elena Afonina, Stanislav Titkov, Jury Buksha

"Flotation processing of water-soluble minerals (potassium ores, sedimentary salts of salt lakes) is currently the main method for production of potassium fertilizers and concentrated carnallite which is the initial product for production of metallic magnesium. Flotation of sylvite (KCl) and halite (NaCl) is carried out in the electrolyte solutions: KCl-NaCl-H2O and KCl-NaCl-MgCl2-H2O. The report presents the results of studies of the effect of concentration and the electrolyte type on the size of air bubbles in a flotation cell in comparison with the floatability of mineral constituents of potash ores. The floatability in electrolytes of various compositions has been studied: - of sylvite (KCl) by alkylamines, - of halite (NaCl) by alkylmorpholines, - of silicate-carbonate slimes contained in the ore by ethoxylated surfactants. The reagent modes (regimes) activating the flotation desliming of potash ores have been developed."

Jan 1, 2014

By M. Abdollahy

Solvent extraction of gallium from Bayer solution of Jajarm Alumina plant was investigated us-ing Kelex100 as extractant. Taguchi experimental design method was used in order to optimize the separation factor of Ga and Al. Optimum conditions were obtained as follows: Temperatuer: 65°C, volume ratio of aqueous phase to organic phase: 3.0:1.0, process time: 60min and organic phase containing 15vol.% Kelex100, 5vol.% isodecanol in kerosene. In this conditions, 74% gallium and 0.3% aluminum was extracted and separation factor was obtained 828.63.

Jan 1, 2014

By I. S. M. K. Ilankoon

In heap leaching the transport of the acid from the drippers to the surface of the ore particles is a major factor in the overall performance of a heap. This flow behavior is complex as the flow is unsaturated and occurs along a tortuous set of inter-particle channels and connections. Previous modeling of this system has used equations from oil and ground water flow to model these systems, but the applicability of these models with the larger particles found in typical heaps is suspect as these systems are not necessarily capillary dominated. In particular, as the characteristic particle size goes from below to above a few centimeters, the flow changes from capillary to gravity dominated. This means that typical heap leaching heaps cover this interesting, but complex, transitional fluid flow regime. In this paper a set of experimental studies of this flow, including PEPT (positron emission particle tracking) based tracer experiments, highly accurate liquid holdup measurements and axial dispersion experiments using salt tracers will be presented. In this study, flow through mono-dispersed particle beds was carried out. In particular, the hysteresis in the liquid holdup as the liquid flow rate into the particle bed is varied is investigated, since this hysteresis means that the relationship between flow rate and holdup is history dependent, an effect not included in models currently used to describe fluid flow in heaps. A theoretical model that describes this hysteresis will also be presented. Keywords: heap leaching, hydrometallurgy, modeling

Sep 1, 2012

By A. N. Zagorodnyaya, T. N. Bukurov, Z. S. Abisheva, A. S. Sharipova

"The paper describes the results of stripping of copper production dusts by leaching with aqueous soda, nitric acid solutions and recovery from solutions resulting in the production of lead sulphate, tribasic lead sulfate (TBLS), ammonium perrhenate, zinc, copper-cadmium cake.The combination of two stripping operations under chosen optimal conditions allows the recovery of 98% rhenium, 82% lead, 92 % copper, and 96% zinc and cadmium each. The major amount of rhenium (~ 80%) is recovered at the carbonization stage, and other metals - at the nitric acid leaching stage.Lead sulfate was precipitated by mixing solutions resulting from carbonization and leaching. Tribasic lead sulfate was produced by dissolving lead sulfate in sodium hydroxide solutions. Rhenium was recovered from mother liquor resulting from lead sulfate precipitation by liquid-liquid extraction and zinc was recovered from raffinates. Trialkylamine (TAA) was used as an extractant for rhenium recovery and di-2- ethylhexylphosphoric acid was used for zinc recovery. Optimal liquid-liquid extraction parameters have been defined allowing the recovery of 96% rhenium in crude ammonium perrhenate and 94% zinc in sulfuric acid solution. Based on the experimental data, the flowchart for dust processing to produce salable products - lead, rhenium, zinc salts has been suggested."

Jan 1, 2003

By I. Y. Titov, Victor D. Samyguin, A. Y. Nikitin

"It is suggested that improvement of separation process efficiency in machines and circuits of selective flotation should be based on application of the principle of technology individualization (PIT). This principle is grounded on the following provisions.The mineral composition of ores is used to establish the correlation between the selective reagent mode and the individual value of hydrodynamic conditions of flotation machines together with individual structure of the process flow diagram. The individuality of all sorts of particles identified by methods of process mineralogy was characterized by their distribution according to the rate of flotation (or spectrum). The spectrum identification is carried out by modeling and by experimental and computational method on the data obtained on various types of laboratory flotation machines.The computer-aided test is used to determine the optimal fraction distribution, which reaches the highest possible level of concentration data. The direction of hydrodynamic factors action on concentration data is estimated based on comparison of design base and experimental spectrum. The improvement of separation efficiency in devices is achieved in special-purpose flotation machines (SFM) the design of which provides optimization of hydrodynamic regime in spatially isolated zones. It is demonstrated that the main parameter of SFM operating mode individualization is the rise rate of bubbles going from the chamber into the froth. During this time the composition of particles optimum for separation is formed on its surface. Additionally, it is necessary to coordinate in the zones the residence time of pulp and foam streams with the air consumption. The improvement of separation efficiency in flotation process flow diagrams may be achieved by making several cascades with SFM installed in them. The individual effective structure of the scheme for a definite ores material composition depends on the ratio of particle varieties in the spectrum and is revealed by modeling."

Jan 1, 2018

By A. O. Gapchich, T. N. Matveeva, N. K. Gromova

"Tin sulfide ores and aged man-made products obtained after their processing are distinguished by a complex material composition and uneven impregnation of sulfide minerals (chalcopyrite, galena, arsenopyrite, etc.) and tin ore (cassiterite). Enrichment of such ores is performed through sophisticated multistage schemes using not only gravitational methods, but also gravity flotation, flotation, magnetic separation techniques. Tin ores also contain rare and precious metals (indium, scandium, silver), characterized by fine dispersity and microscale to nanoscale fineness of mineral formations. During flotation concentration these metals are extracted along with the main ore minerals into concentrates (tin, copper, tungsten, etc.), however, up to 10-20 % of them are lost with final tailings. The aim of the work is an experimental study of the modification of the surface of sulfide minerals and cassiterite by stable metal-collector complexes to increase extraction of fine tin, silver, copper and other metals from complex tin ores. Triamide cyanuric acid (TCA) was studied as a thin silver flotation modifier. Thermophilic polymer with a functional group of phenylphosphine TMPPh was used as a selective flocculant. For experimental studies of the physical and chemical effects of collecting agents on the surface of minerals the following analytical techniques were used - the analytical scanning electron emission ASEM (LEO 1420VP INCA OXFORD ENERGY 350) and laser (KEYENCE VK-9700) microscopy, measurements of electrode potentials of mineral anthills by potentiometric titration, monomineral and pulp flotation. New data on formation of the adsorbed layer of DBDTC on the surface of chalcopyrite, galena and arsenopyrite were obtained, and the dimensions of the reagent films and the strength of their adsorption. The indiscriminateness of cassiterite to DBDTC ensures its selective separation into a chamber product during the flotation of sulfides. It is shown, that modification of the sulfide surface by stable complexes Me-DBDTC and Ag-TCA-TMPPh will increase the recovery of non-ferrous metals and silver into a collective sulfide concentrate and will provide a high-quality tin concentrate for flotation of tin sulfide ores.The studies were perfomed with the aid of the Russian Science Foundation (Project No. 17-17-01292).INTRODUCTIONTin sulfide ores and aged man-made products obtained after their processing are distinguished by a complex material composition and uneven impregnation of sulfide minerals (chalcopyrite, galena, arsenopyrite, etc.) and tin ore (cassiterite). Enrichment of such ores is performed through sophisticated multistage schemes using not only gravitational methods, but also gravity flotation, flotation, magnetic separation techniques. Tin ores also contain rare and precious metals (indium, scandium, silver), characterized by fine dispersity and microscale to nanoscale fineness of mineral formations. During flotation concentration these metals are extracted along with the main ore minerals into concentrates (tin, copper, tungsten, etc.), however, up to 10-20 % of them are lost with final tailings. In this regard, it seems advisable to use new varieties of flotation reagents in order to increase extraction of finely dispersed tin, silver, copper and other non-ferrous and precious metals from multi-metal tin ores (Bocharov and Ignatkina, 2007; Khanchuk etal., 2012; Wu and Zhu, 2006; Yusupov etal., 2016)."

Jan 1, 2018

By Eberhard Gock

The worldwide implementation of corrosion protection of low alloyed automotive metal sheets by zinc coating has led to supply shortages of zinc free non-alloyed steel scrap in the foundry industry. In a collaboration project, partly financed by the German government, with partners from the automotive industry, zinc metallurgy, scrap trading, foundry industry, and plant construction, a new acid-based pre-dezincification process has been developed, and a pilot plant with throughput of about 100 t/d has been put into operation at the Clausthal Umwelt-Institut GmbH (CUTEC) together with the Clausthal University of Technology in Germany. During the treatment process, acid from a zinc metallurgical plant will be supplied, which can be recycled to the primary zinc extraction process after raising the zinc concentration to more than 130 g/L zinc. This way, the separation of small amounts of iron by precipitation and the electrolytic zinc winning are outsourced and, as a result, the pre-dezincification process runs waste-free. In Germany, the amount of zinc coated ?new scrap? is approx. 3 million t per year with a zinc content of approximately 60,000 t per year. The possible additional incomes for the dezincified steel scrap are in the order of ?40 to ?50 per ton of scrap, the gained zinc content during the acid dezincification defrays the costs of the process, if the throughput is more than 700 t/d. In comparison to conventional dezincification during the electro arc furnace process followed by upgrading in a rotary kiln (Waelz process), the acid dezincification process running at a maximum of 50°C will cut the energy costs by up to 74% and the CO2 emission by up to 88%. In fact, a demonstration plant is being designed right now and will be installed for processing a part of the zinc coated metal scrap from the Volkswagen AG in Wolfsburg, Germany. Keywords: steel scrap, zinc-coated steel, dezincification methods, acid

Sep 1, 2012

By L. Gao, X. Gui

Fine coal obtained from Kailuan mine served as the processing object of this study. This material was difficult to separate. A flotation rate experiment was designed to investigate the process distribution characteristics of size and density during fine coal flotation. Size and density analyses of five clean were studied. The mineral morphology of flotation rate experiment cleaning was observed through scanning electron microscopy. The fractions -0.074+0.045 mm and -0.045 mm exhibited the best practical floatability and presented the highest combustible body recovery rates, but the selectivity and natural floatability of these two fractions were the worst. The - 0.074 mm fraction has contaminated the clean coal from the early stage of flotation, and the cumulative clean coal ash of -0.074 mm reached up to 17.20%. The low and middle-density classes displayed varying flotation behavior, but the flotation yield difference was only nearly 3%. The middle-density class caused the clean coal to have high ash content. The poor selectivity of fine coals, middle-density fraction, and fine mud resulted in high-ash clean coals during flotation. Thus, improving the selectivity of fine coal, restraining the flotation of fine mud, and grinding the coal to decrease the middle density mass fraction to liberate clean coals can yield high-quality clean coals through flotation.

Jan 1, 2014

By Yuemin Zhao

Pre-combustion cleaning of coal plays a key role in the process of efficient and clean utilization of coal resources. Recently, wet beneficiation of coal is predominant around the world. Nevertheless, wet beneficiation processes are limited by the increasingly serious problem of worldwide shortage of water, especially in China. Thus, it is imperative to develop efficient dry coal beneficiation techniques. Currently, several technologies such as air dense medium fluidized bed, compound dry cleaning and air jigging have successfully achieved high-efficiency separation of 50~6 mm coal. However, in recent years, a large amount of fine coal is generated as the mechanized mining technology has been progressively deployed in coal sector. Thus, it is necessary to develop efficient dry beneficiation techniques for fine coal. In recent years, many countries including China, India, Canada, Germen, and Australia have carried out many research works on fine coal dry beneficiation techniques. China University of Mining and Technology has carried out systematic researches on the introduction the vibrated energy to traditional air dense medium fluidized bed for fine coal beneficiation. This paper studied air dense medium vibrated fluidized beds (ADMVFB) for fine coal dry beneficiation. The experimental results show that the coal of <6 mm size can be beneficiated in an ADMVFB efficiently with the E value of 0.065~0.085, the separating density can be adjusted in the range of 1.45~2.2 g/cm3, and the lower limit of beneficiation can reach to 0.5 mm. Keywords: fine coal, air dense medium vibrated fluidized bed, coal separation, dry separation

Sep 1, 2012

By Priyanka Dhar, Kurt Aasly, Hanumantha Rao Kota, Hassan Bouzahzah, Maria Thornhill

The interest in investigating the processing characteristics of mineral deposits in Norway has seen an upsurge in the last decade. One of the major areas of interest is a huge copper deposit, operated by NUSSIR ASA located in the Repparfjord Tectonic Window in the caledonides of west Finnmark. This study reports analysis of ore from the deposit for development and modifications in the flotation flowsheet for the NUSSIR ASA copper ore. The mineralogical characterization for the ore sample was achived by optical microscopy and Zeiss automated mineralogy while grinding characteristics were tested using Bond Index tests. The results confirmed the presence of Cu minerals in the form of chalcocite, chalcopyrite and bornite in the samples, which are mainly liberated in the – 105 µm size range. The majority of non-liberated copper sulphides associated with silica and the carbonates varies from 3 to 28 percent in the –250 µm samples . It is also observed that the copper minerals are uniformly distributed in all size ranges. Selective flotation of NUSSIR copper ore was performed in different size fractions with a motive to identify the correct liberation size and thus to obtain a copper concentrate meeting the quality requirements. The flotation experiments are essentially performed in two stages: the rougher and the cleaner stage. Mass balance calculations were performed showing that approximately 88 percent of copper can be obtained at the end of the process. Ultimately, overall circuit copper recoveries ranged between 83.5 to 88.1 % with a concentrate grade of 35 to 48 % Cu.

Jan 1, 2018

By Andrzej Wieniewski, Cezary Regula, Bozena Skorupska, Krystian Cichy

"In this paper, experiences from Polish non-ferrous metals ores enrichment plants in the copper and blende concentrates quality improvement are discussed. The blende concentrate being produced in ZGH Boleslaw S.A., with Zn content of about 54,5% is characterized by the relatively high magnesium content reaching a level of 1% resulting from the dolomite presence, while for the zinc production by electrowinning a concentrate in which magnesium content should not exceed 0,3% is required. The implemented new technology for the quality improvement of blende concentrate is based on the leaching of zinc concentrate with sulfuric acid aimed at dissolving of the contained dolomite, and then flotation of the leached concentrate. It allows to obtain a concentrate with magnesium content below 0,1% at the simultaneously increased zinc content to about 57,5%. In the paper, laboratory tests results on the development of optimal flotation flowsheet for the gypsum removal and the industrial tests results concerning the process optimization of this flotation are discussed. In turn, the copper concentrate being produced in Polish copper ore enrichment plants KGHM PM S.A., is characterized by the increased organic carbon content - above 8%. It creates problems with the smelting of this concentrate because of difficulties with the heat removal derived from the combustion of organic carbon in the flash smelting process. The implementation of segregating flotation to the industrial practice allows the effective production of two concentrates with the differentiated chemical compositions - a concentrate with increased copper content and reduced organic carbon content for the flash smelting process, and a concentrate with lower copper content and increased organic carbon content for the shaft smelting process. In the paper, conditions of the segregating flotation and the achieved results are described."

Jan 1, 2014