Search Documents

By Cees van Rhee, Rudy Helmons

INTRODUCTION Seafloor Massive Sulphides are typically found near the oceanic ridges at larger water depths (>1km). The physical properties of SMS, as shown in table 1, are comparable to the properties of weak rock. One of the technical challenges to enable extraction from these locations is the cutting or excavation process. Experiments have shown that the energy needed to excavate the material may increase with water depth (Alvarez Grima et al. 2015). Besides that, it is demonstrated that rock that fails brittle in atmospheric conditions can fail more or less in a plastic fashion when present in a high pressure environment, as would be the case at large water depths. The goal of this research is to identify the physics of the cutting process and to develop this into a model in which the effect of hydrostatic and pore pressures is included. The cutting of rock is initiated by pressing a tool into the rock. As a result, at the tip of the tool a high compressive pressure occurs, which leads to the formation of a crushed zone. Depending on the shape of the tool and the cutting depth, shear failures might emanate from the crushed zone, which will eventually expand as tensile fractures that can reach to the free rock surface. Through this process intact rock will be disintegrated to a granular medium. For an overview of the process (figure 1). Additionally, the presence of water in the pores of and surrounding the rock influences the cutting process through drainage effects. The most relevant effects are weakening when compaction and strengthening when dilation occurs in shearing and tension. Deformation of the rock causes the pore volume to change, resulting in a under or over pressure. As a result, the pore fluid needs to flow. The magnitude of the potential under pressure is limited through cavitation of the pore fluid, limiting further reduction of the pore pressure (figure 2). The drainage effects cause the rock cutting process in a submerged environment to show a stronger dependency of both the hydrostatic pressure as well as the deformation rate (figure 3).

Jan 1, 2018

By P. E. Mikhailk

From July 29 to September 15, 2004, the 178th cruise of the R/V Sonne took place under the KOMEX program in the Sea of Okhotsk. One of the cruise objectives was to dredge two different kinds of seamounts: 1 ? underwater volcanoes from the north slope of the Kurile Basin; 2 ? a seamount formed by tectonic (non volcanic) processes from the Kashevarov Trough. The underwater volcanoes are young edifices (0.84 ± 06 Ma, Baranov et al., 2002) with heights ranging from 150 to 300 m. Tops of the volcanoes are located at depth of 1260 to 2340 meters. The volcanic edifices are formed by olivine-clinopyroxene-plagioclase basalts. Dredge samples are covered by Fe-Mn crusts up to 40 mm thick. The seamount from the Kashevarov Trough is a tilted block. The height of the seamount is about 400 m and its top is located at a depth of 960 meters. Biotite hornfels, conglomerates, granodiorites, dropstones, and Fe-Mn crusts were recovered there. The thicknesses of crusts are up to 150 mm. Fe-Mn crusts from the underwater volcanoes differ from Fe-Mn crusts from the Kasevarov Trough seamount in morphology as well as in mineralogical and chemical compositions. The research was supported by the Program of the Presidium of the Far East Branch of the Russian Academy of Sciences (project ? 05-III-G-08-086).

Jan 1, 2005

By Hunsoo Choi

Internal textures of manganese nodules from Clarion-Clipperton zone of northeastern Pacific Ocean are classified into five textural zones: columnar-textured layered zone, cuspate-textured layered zone, cuspate-textured massive zone, cuspate-textured porous zone and massive- textured massive zone. Vernadite is the main constituent mineral in the columnar- and cuspate-textured layered zone. Buserite sometimes occurs in the cuspate-textured layered zone. The cuspate-textured massive zone is mainly composed of buserite. Todorokite is also associated with buserite in the massive-textured porous zone, where cuspates and globes are partially replaced by massive texture. In the massive-textured massive zone, todorokite, buserite and birnessite occur together. The analyzed elements of all zones are also classified into four elemental groups by the cluster analysis of correlation coefficients: Mn group, Cu-Ni-Mg group, Fe group and Si group. Mn group consists of Mn and K. Cu-Ni-Mg group consists of Cu, Ni, Zn, Mg and/or Ca, Na. Fe group consists of Fe, Co, Ti and/or Ca, P. Si group consists of Si and Al. Each textural zone is composed of three or four elemental groups. These four elemental groups are correlated with mineral composition, such as, Mn group with todorokite, Cu-Ni-Mg group with buserite, Fe group with Co-bearing iron-oxyhydroxide minerals, and Si group with silicates.

Jan 1, 2002

By Randolph A. Koski

Since 1985, numerous constructional sulfide-sulfate deposits in the form of mounds, pinnacles, chimneys, and sheets have been located between 40°45' and 41°05'N latitude in Escanaba Trough, the sediment-covered axial valley of the Southern Gorda Ridge. Single-channel seismic data indicate that three volcanic edifices up to 6 km in width penetrate as much as 500 m of turbidites that fill the valley; pillow and sheet flow lavas are exposed on the sea floor where these volcanoes breach the sediment surface. Observations from deeply towed camera systems and submersibles show that the largest hydrothermal deposits occur along the step-faulted northern flank of the central volcanic edifice and on the peripheries of steep-sided, sediment-capped hills, approximately 1 km wide and 100 m high, that rise above the valley floor. The sulfide deposits are highly oxidized, eroded, and partly buried by unconsolidated sediment; aprons of sulfide talus extend downslope from the mounds. Two types of sulfide have been sampled by dredging and submersible. The predominant mound and chimney material is pyrrhotite-rich massive sulfide with low amounts of Zn, Pb, Cd, and Ag. Coarse-grained zones with high porosity mark the location of myriad fluid channelways. Thin crusts of barite associated with pyrrhotite-rich sulfide have Au contents up to 2 ppm. Zoned fragments of polymetallic (Fe-Zn-Pb-Cu-As-Ag-Sb) sulfide dredged from a single site near 41°01'N latitude are part of a chimneylike vent structure with a

Jan 1, 1988

Ancient volcanogenic Cu-Zn-Pb-Ag-Au massive sulfide ores commonly have associated with them along strike and in the immediate hanging wall a distinctive sediment that is thin, usually cherty and metal enriched, and generally referred to as an "exhalite horizon" or "tuffaceous exhalite". Typical examplks include the 13 Ma tetsusekiei of the Kuroko deposits of Japan (Kalogeropoulos and Scott, 1983, Econ. Geol.) and the 2700 Ma contact tuffs of Noranda, Canada (Kalogeropoulos and Scott, 1989, Can. J. Earth Sci.) and Key Tuffite of Mattagami, Canada (Liaghat and McLean, 1992, Explor. Min. Geol.). Attempts to use trace element distributions as lithogeochemical guides to ore have been largely unsuccessful. Exhalites have been considered to be the products of seafloor hydrothermal activity that is peripheral to the main ore-producing vents. However, large actively-forming polyrnetallic sulfide deposits at the Explorer mid-ocean basalt spreading ridge (1 850 m depth) in the NE Pacific and the eastern Manus back-arc dacitic spreading center (1650 m depth) in the western Pacific have demonstrated that the exhalite horizons are more likely produced by fallout of particulates from the main hydrothermal plume. In a typical hydrothermal plume, grains of >27 µm represent up to 97% of the mass (although only 2% of the population) of the particulates and are calculated by Stokes equations to fall from the plume to the seafloor within a few krn of their source. The particles are primarily composed of anhydrite, barite, amorphous silica, iron oxyhydroxides and metal sulfides and oxides. Plumes are subject to bottom currents which push them in preferred directions, just like smoke plumes in the atmosphere are subject to the vagaries of wind direction. Bottom currents in the deep ocean can be 50 m/min or

Jan 1, 1993

By Elizabeth McIsaac, Wylie Spicer

"In July 2016 the International Seabed Authority (the “ISA”) released a first working draft of its mineral exploitation regulations as well as the standard contract terms for mineral resources in the Area, for which stakeholder input was sought in late 2016. In January of 2017 the ISA released a discussion paper on environmental matters related to these draft regulations. The ISA is now in the process of further developing its draft exploitation regulations and standard contract terms to ensure that seabed mining is carried out in an environmentally sound way for the common benefit of mankind.As the regulator of the “Area”, the ISA can draw lessons from onshore mining regulators and offshore petroleum regulators for their experiences in legislative drafting to smoothly and safely oversee project development, implementation, and closure. However, one of the unique challenges that the ISA faces in regulating private industry is its status as an international organization and not a sovereign nation, which results in a significantly different legal relationship between the regulator and the regulated. The result is that the exploitation contract is the sole legal connection between the mining proponent and the regulator for the exploitation phrase of the project.Accordingly, in the regulatory development process, the ISA must carefully consider which rights and obligations are set out in the exploitation contract versus the regulations. This decision will dictate the flexibility the ISA will have to modernize the conduct required of mining proponents in response to changing best practices in the industry, technological progress, and advances in the understanding of the marine ecosystem. As the first working draft of the exploitation regulations sets out an initial contract period of twenty years, it is crucial for the ISA to carefully consider the rights, obligations, and procedures it agrees to in the exploitation contract, as unilateral amendment will not be possible after contract execution."

Jan 1, 2017

By G. Cherkashov

The geodiversity of seafloor massive sulfides (SMS) deposits at the slow- and ultra-slow spreading ridges is of great variety (Fouquet et al., 2010). Tectonics and magmatism are the two principal factors which control SMS formation and localization. The geological setting of SMS deposits is determined by their position relative to the rift valley and by the types of rocks hosted (Table 1). Depending on the first parameter, SMS deposits could be localized at [ ] the axial volcanic ridge or at the flank of the rift valley. Basalts, deep-seated gabbro, and serpentinized peridotites are distinguished among the hosted rocks. The outcrops of deep-seated rocks are exposed at the flanks of the rift valley. The tectonic mechanism of the lower crust and mantle rocks exhumation process is connected with very large offsets along the detachment faults, resulting in a forming oceanic core complex (OCC) (Smith et al., 2006; MacLeod et al., 2009). The SMS related to OCCs are represented by such ore clusters as Ashadze, Logatchev, Semyenov, and some others (Table 1) and are increasing steadily in number. This fact in combination with widespread OCC formation at the slow-spreading ridges (Escartin et al., 2008) and high grades of metals in SMS related to OCCs has provoked considerable scientific and economic interest in these types of deposits. It could be mentioned in this regard that the first two applications to the International Seabed Authority for prospecting and exploration of sulfides have been submitted for the areas in the spreading centres with wide distribution of the core complexes.

Jan 1, 2011

By C. H. Hobbs

A recently completed series of projects funded by the Commonwealth of Virginia and the U.S. Minerals Management Service was designed to assess the distribution of heavy minerals on the inner continental shelf adjacent to Virginia. These projects indicate that a suite of minerals of both strategic and economic interest is present. Analysis of several hundred grab and core samples shows that zircon, monazite, and titanium minerals (ilmenite, rutile, and leucoxene) occur in quantities that probably warrant further study by the mineral industry. Furthermore, side-scan sonography and shallow seismic profiles have provided information on the thickness and areal extent of the mineral-bearing sands. Possible development of the resource is enhanced by a potential use of offshore sand for beach nourishment. The results of the preliminary studies have been presented in open-file publications and oral reports in order that the mineral industry might have an up to date basis upon which to consider more exploratory work. Much of the effort south of the mouth of Chesapeake Bay was made in cooperation with and enhanced by an independent study of sand resources for beach nourishment and other needs. Preliminary review of the quantitative analyses of the heavy-mineral content of several hundred samples demonstrates that the distribution of high concentrations is non-uniform. From core data, the greatest abundances of some economic heavy minerals (ilmenite, rutile, leucoxene, monazite, and

Jan 1, 1988

By Hyung-woo Kim

This paper concerns about steering characteristics of pilot mining robot, named MineRo II, crawling on extremely cohesive soft soil using dynamic simulation software. The MineRo-II for deep-seabed manganese nodules, which aims at the use for pilot mining test, was manufactured in 1/5 scale of commercial mining capacity (see Fig. 1).

Sep 14, 2011

By S. Jeffress Williams

The topic area for this paper covers the United States portion of the northern Gulf of Mexico, extending from the Rio Grande delta east to the Florida peninsula. Declaration of an Exclusive Economic Zone in 1983 expanded Federal economic jurisdiction on the continental margins from 12 to 200 nautical miles seaward from the coast. The nation-wide area of the EEZ totals 3 million square nautical miles, with approximately 186 thousand square nautical miles in the Gulf of Mexico. In the Gulf, the continental shelf has an area of 81 thousand square nautical miles, extending to a depth of 600 ft. and having widths of 6 to 120 nautical miles. Specific areas on the shelf offer the greatest potential for containing aggregate and other hard mineral resources. The primary geomorphic features along the Gulf coast include: barrier islands, chenier plains, tidal inlets, bays and lagoons, estuaries, and deltaic headlands. These features are composed of terrigenous siliclastic sediments, except for the west Florida coast, south of 29°N latitude, which is dominated by carbonate sediments. On the shelf, the primary features are linear sand shoals and associated sand sheets, relict delta lobes and channels, and banks related to salt diapirs and coral reefs. The composition and distribution of sediments in these coastal and shelf features are determined by numerous geologic factors including: seabed topography; riverine sediment discharge; sediment dispersal patterns due to currents, waves, storms and tides; tectonics and subsidence; and repeated fluctuations in sea level.

Jan 1, 1986

By Tetsuo Yamazaki

The Kuroko-type seafloor massive sulfides (SMS) in the western Pacific have received much attention as sources for economic recovery of gold (Au), silver (Ag), copper (Cu), zinc (Zn), and lead (Pb). Since the end of the 1980s, the Kuroko-type SMS have been found in the back-arc basins and on oceanic island-arc areas. In Okinawa Trough (Halbach et al., 1989) and on the Izu-Ogasawara Arc (Iizasa et al., 1999) are the typical representatives in the Japan’s EEZ. They yield a higher concentration in Au and Ag than the SMS found in ocean ridge areas (Rona, 1985). Similar formation processes with the Kuroko ore deposits on-land in Japan have been expected and outlined by many researchers (Sillitoe, 1982; Scott, 1985). The higher Au and Ag contents have increased the chances for profitable mining operation, which is under consideration by a private company (Malnic, 2001). Information about the resource potential of the targeted Kuroko-type SMS deposit, such as the amount of SMS ore body, the inside structure, the mean metal yields, and the geographical details are necessary for a technical and economic validation analysis for the development. The Sunrise Deposit of Myojin Knoll on Izu-Ogasawara Arc in the Japan’s EEZ is selected as a target for the technical and economic validation analysis. The relatively higher amount of information on its resource potential is the reason why the deposit is selected.

Sep 24, 2006

By Irina A. Pulyaeva

Hydrogenetic Fe-Mn crusts play an important role in marine mineral-deposit research because of their widespread occurrence and high concentrations of valuable and rare metals. Most Fe-Mn crust deposits occur on the tens of thousands of seamounts found in the global ocean as well as on ridges and plateaus. Because of these circumstances, it is essential to clarify a number of outstanding issues with regard to Fe-Mn crust history and development, including controls on metal sources and concentrations. The first-order characteristics of Fe-Mn crusts as potential ore deposits include concentrations of metals (grade) and the thickness of crusts (tonnage), which vary depending on Fe-Mn crust structure and texture. Data on the structure, composition, age, and deposit characteristics will help define which factors are key for the creation of mineral accumulation and which combination of factors leads to the formation of potentially economic concentrations of metals. In this paper, we address the structure and characteristics of Fe-Mn crust stratigraphic sections collected from Central and Western Pacific seamounts. We describe the changes in mineralogical and chemical compositions of crust layers of different ages, the occurrence and regional distribution of these layers that correlate regionally, and reconstruct the paleoceanographic conditions that influenced crust growth.

Jan 1, 2010

By S. E. Boyd

Studies of benthic recolonization following the cessation of dredging in U.K. waters and elsewhere are limited, and are largely confined to experimental circumstances. Investigations of the physical and biological status of licensed areas in the U.K. at various times following cessation of commercial dredging are very limited and so judgments as to the likely progress towards environmental restoration and the time-scales are often based on predictions rather than real data. This study was established to address this deficiency by assessing the status of seabed substrata and associated benthic fauna within and outside areas where dredging had ceased and to conduct follow up sampling to monitor progress towards full recolonization.

Jan 1, 2004

By Valery M. Yubko

During the last ten years seven applications for nodule-bearing areas of the World Ocean Floor International Region (IR) have been made by national companies of Russia (Yuzhmorgeologiya), France (IFREMER/AFERNOD), Japan (DORD), India (The State Department of Sea Resources Development), China (COMRA), Korea (KORDI) and the Interokeanmetal Joint Organization (IOM) of some East European countries and have been registered by the Preparatory Commission of the United Nations International Seabed Authority (ISA). Besides these groups registered within Resolution 11 of the Final Act of the III United Nations Conference on the Law of the Sea there are four international consortia registered in the USA [Kennecott (KCON), Ocean Mining Associates (DMA), Ocean Management Incorporated (OMI), and Ocean Minerals Company (OMCO)], which have interest in areas in the IR and can be considered as potential applicants. All registered areas (with the exception of the Indian Ocean) including the areas of potential applicants and also 6 areas, reserved for the ISA are located in the Clarion-Clipperton Zone of the Pacific Ocean. If within each area not less than one deposit of polymetallic nodule-bearing ores can be discovered, then, the total number of such deposits, for the present moment, is 20.

Jan 1, 1994

By I. V. Kubrakova, O. A. Tyutyunnik, M. L. Getsina, A. M. Asavin

An analysis of noble metals (NM) in natural samples is most problematic. Determination of their traces in geochemical samples, in part, for the purpose of deposit evaluation, is a difficult analytical task. A number of international standard reference materials of rocks and ores, in which NM content is certified, is estimated at a half dozen. For example, in the International proficiency test for analytical geochemistry laboratories (GeoPT), which is held by the Department of Earth Sciences (The Open University, United Kingdom), the data for gold and platinum are observed very rarely, and the results obtained in different laboratories differ on 1-3 orders of magnitude. It is caused by low contents of NM in nature, by a variety of their complex and mineral species, as well as by a complicated matrix composition of platinum-containing objects. Among these objects are ferromanganese ores, enriched strongly with Fe, Mn, Ni, REEs - the elements hampering a precise determination of NM due to a complexity of instrumental inter-element correction. The absence of the reliable methods of NM determination in these ores drastically limits the possibility of deposit evaluation.

By Johnson R. Cann

Ocean floor sulfide deposits are now known from many parts of the world mid-ocean ridge system and from some seamounts. Clearly they can be expected to occur commonly on the ocean floor. However, only two or three of the known deposits appear to approach the million-ton size, and in none of the deposits has the grade been well-defined. Can knowledge of the processes that happen within the hydrothermal plumbing below deposits help define the conditions under which large, high-grade deposits form? Here I review present knowledge of ocean-floor hydrothermal processes to attempt a first answer to this question. There are three sources of information about these processes. The solutions emerging from active systems must be compatible with patterns of alteration that underlie the volcanogenic sulfide deposits of ophiolite complexes, which are slices of ocean crust thrust onto land. Both of these types of evidence can be linked by computer modelling of the exchange of heat and metals between rocks and flowing water.

Jan 1, 1988

By V. Alexandrov

This paper presents the results of theoretical investigations of the energy requirements of the hydraulic lifting of mined materials from the seabed to the sea surface in the deep-sea mining of solid minerals such as manganese nodules in the Clarion-Clipperton region of the Pacific, situated on the sea floor in water depths of 4,500 m or more. The principal element of the developed underwater transport system is the Underwater Chamber, which is connected by flexible pipeline to a mining machine that gathers nodules from the seabed, mixes them with seawater, and feeds them into a flexible pipeline. In this paper, we discuss the question of the optimum water depth for placement of the Chamber, the interior of which is designed to maintain a 1-atmosphere pressure. We present a method for calculating this depth as it relates to the mechanical characteristics of solid particles, the shapes and size distributions of the particles, particle and slurry density, and other properties. These investigations were carried out in hydro-transport laboratory of the Saint-Petersburg Mining Institute and the hydraulic laboratory of Faculty Environmental Engineering in Wroclaw Agricultural University. KEY WORDS: deposit, nodule, flexible pipeline, pressure drop, concentration, hydromixture

Jan 1, 2005

By Andrea Koschinsky, Luise Heinrich, Stefan Gößling-Reisemann

"Germany, like several other countries, has entered a contract with the International Seabed Authority (ISA) to explore the prospects of commercial manganese nodule mining in the Clarion-Clipperton Zone (CCZ). Ensuring a maximally sustainable deep-sea mining operation requires a thorough understanding of the environmental impacts associated with every step of the mining process from the extraction of the nodules at the seafloor to the refinery on land. Against this background, the project presented here applies a combination of scenario-building and life cycle assessment (LCA) to assess and evaluate the sustainability performance of the individual process steps as well as the entire mining operation.Life cycle assessment (LCA) is a comprehensive methodological framework that allows the identification and quantification of impacts occurring during a products life-cycle, as well as the analysis and evaluation of their contribution to pre-defined impact categories, such as climate change, acidification and toxicity (Rebitzer et al., 2004). Until now, LCAs with a focus on raw material extraction have almost exclusively been applied to terrestrial processes. Noteworthy exceptions are offshore drilling, offshore wind farms and ocean fishing. Hence, the first part of the project is to investigate in how far LCA can be applied to deep-sea settings and if and in what way it could be adapted to be used in a deep-sea mining context."

Jan 1, 2017

By Daniel E. Walsh

The recovery of most minerals, which are amenable to gravity concentration, is standardly determined by accurate sampling and assaying. .With respect to particulate - gold ores, sampling and assaying are still the convention, but the accuracy and reproducibility of these operations are much discussed and debated points. Evaluation of gravity concentrators by conventional sampling and assaying techniques is very time consuming, costly and may introduce a large amount of uncertainty into the results due to the particulate nature of placer gold. These problems are not unique to placer gold ores and apply to any low grade ore with particulate values. A gravity concentrator evaluation process developed by MIRL employs the use of neutron activated gold (198Au) and radiation detection circuits which monitor the concentrator's product pulp streams. Concentrator recovery is determined from the ratio of the number of gold particles detected as passing into the concentrate to the total number of gold particles detected over all monitored pulp streams. This system eliminates the experimental errors introduced by sampling, sample reduction, and assaying and allows recovery to be evaluated for gold particles of specific sizes, shapes, and flatness. This system enjoys its greatest utility where a large number of tests are to be run in order to evaluate a concentrator over a variety of operational settings, i.e. factorial designs, and allows accurate testing of concentrators operated in closed circuit systems. Beginning in 1984, MIRL conducted radiotracer studies of unit processes, which included jigging, static wedge wire screening, elutriation, and concentration with compound water cyclones.

Jan 1, 1989

By Alexander Malahoff

Mineral zonation studies were conducted on hydrothermal vents of two hot spot volcanoes. One study site is located within the Axial Caldera of the axial hot spot volcano of the Juan de Fuca Ridge. The young high-temperature hydrothermal vent field consisting of two polymetallic sulfide chimneys, five meters high, located at 130°01.5'W, 45°56.5'N, along a fault complex at the base of the southwestern wall of Axial Caldera was sampled during four ALVIN dives in 1983. Temperatures of up to 270°C were measured within the orifice of one of the chimneys, which was then broken off and recovered with the submersible. Both black and white "smoke" was observed to be emanating from the one chimney sampled. The high-temperature chimney extends directly from a field of broken lobate lavas which are located at a water depth of 1,550 meters, about 200 meters east of the caldera wall. The chimney makes one of the shallowest active high-temperature vents studied to date. The vent is surrounded by clumps of vestimentiferan worms and is located within an elongate field of red-colored iron smectite blankets and chimneys. The low-temperature field forms a ribbon 150 meters wide, extending for about 1,300 meters at the base of the wall. Chemical analyses of the hydrothermal deposits ranging from the polymetallic sulfides of the chimney to the outer zones of the low-temperature field show a range of elemental assemblages consistent with temperature zonation around the vent. Chemical zonation within the high-temperature

Jan 1, 1988