Search Documents

By H. C. M. Gordon

MR. A. D. BADOUX: I have listened to Mr. Gordon's excellent paper with great interest, as I personally have gone through some of the experi­ences he has so clearly depicted. In particular, there were a good many times when we were greatly exercised in our minds as to whether we were justified or not in closing-off certain sections in the Allan mine. The difficulty in these cases arose from the fact that a peculiar smell could be detected in these sections but at the same ti me there was no positive evidence of spontaneous combustion either from heat being apparent or from the possible indications of fire getting any worse. It was suspected that the small percentage of -carbon monoxide that could be obtained by analysis in the air in these sections, and also the peculiar odour, were emanating from the coal itself, and, in order to verify this, bore-holes were drilled in the coal and the gases released from these bore-holes were analyzed. They were found to contain carbon monoxide. After quite a considerable length of time this contained carbon monoxide gradually diminished and finally could not be detected when analyzing such samples of gas. It was our intention to follow this matter up further, as such an occurrence of carbon monoxide is practically unknown, but the sections in which these occurrences were found had to be abandoned. Mr. Gordon referred t0 a case of spontaneous combustion in the Allan . mine, and I may say that, although the section in which that occurrence took place was travelled and carefully examined every day by the colliery officials, yet nothing unusual was noticed until the fire actually took place. This tire was the cause of a slight explosion.

Jan 1, 1938

By L. Xia, B. Hart, J. Nigim, Z. Chen

"Grinding ore is an important step in the flotation process. Not only does grinding reduce particle size and liberate minerals, it also creates conditions for reactions to occur on particle surfaces that can aide or inhibit flotation. There have been numerous studies examining various grinding regiments and the effect on flotation pulp chemistry, including autogenous grinding and using media of variable composition. There have been however, few studies looking at the effect of variability in grinding media size on pulp chemistry and subsequent flotation. This study attempts to link changes in pulp chemistry in response to variations in grinding media size to flotation recovery. It uses probes mounted in the grinding chamber (pH, Eh, DO, and conductivity) to monitor pulp chemistry changes during grinding of a Cu-Zn ore. Surface chemistry analysis by ToF-SIMS was performed on sphalerite from the mill discharge. Activator and depressant species were monitored on the mineral surfaces and their presence was evaluated in the context of variability in pulp chemistry linked to differences in grinding media and its ball size.INTRODUCTIONIt has been widely recognised that not only does grinding reduce particle size and liberate minerals but the grinding environment has a large effect on the flotation of sulphide minerals. This effect is attributed to Eh change, iron hydroxide coating on surfaces, oxygen reduction, precipitation from solution and galvanic coupling (Grano, 2009). As early as 1960, it was reported that after grinding the ores in an iron mill the natural floatability of sphalerite was reduced significantly (Rey and Formanek, 1960). Kocabag and Smith (1985) studied on the industrial circuits showing that the depression of sulphides flotation in a steel mill is possibly due to the coating of iron oxidation products. Peng, Grano, Fornasiero, and Ralston (2003a, 2003b) found that iron contamination from grinding media plays a dominant role in depressing galena and chalcopyrite flotation. Huang, Grano, and Skinner (2006) reported the same observation in the flotation of arsenopyrite."

Jan 1, 2016

By Ros Taplin

Realizing the potential of cutting greenhouse gases (GHGs) associated with mining, a variety of approaches has been proposed for their mitigation. The Clean Development Mechanism (CDM) under the Kyoto Protocol to the UN Framework Convention on Climate Change (UNFCCC) has been a key mechanism to assist in implementation of mitigation measures. The objectives of CDM are not only to assist Annex I countries in meeting their GHG emissions reduction targets with cost-effective reduction but also to achieve sustainable development in non-Annex I countries. However, apart from China, India, Brazil and Mexico, many developing countries are still in the stages of formulation or realizing CDM strategies. Projects associated with methane capture and flaring are the fourth most prevalent type of CDM project internationally. This research primarily has addressed emissions abatement and sustainable development aims and effectiveness of registered CDM projects associated with coal mining in China. The paper reviews 30 currently registered CDM projects in China on the UNFCCC database and six other non- Chinese projects. Systematic evaluation involving content analysis of documentary evidence regarding coal mining CDM projects is presented in relation to firstly, quantitative reduction of GHG emissions and secondly, sustainable development outcomes. The projects have been assessed via a set sustainability criteria. Overall it was found that sustainable development goals are only briefly referred to in Project Design Documents, Letter of Approvals and validation documents. Varying types of sustainability initiatives have been implemented with weak to strong indications of effectiveness. This has implications for the future effectiveness of CDM projects in the mining sector, the proposed new market mechanism under UNFCCC, and for assessment of projects under mechanisms established outside the UNFCCC.

Aug 1, 2013

By E. Ghali, A. D. Bas

"Treatment of oxide, e.g. roasted gold ores has received relatively less attention than sulphidic ones and recently, handling of oxide gold ores is becoming essential. In this study, the influence of roasted gold ore (RGO) slurry (at 35% solid ratio) on the electrochemical dissolution of gold has been examined using pure gold and iron oxide minerals (hematite, maghemite, and magnetite) as disc electrodes by zeroresistance ammeter mode either in one or two separate containers. The presence of slurry decreased galvanic currents, i.e. corrosion rates due to the release and increase in the amount of soluble and/or insoluble species that could retard further the anodic behaviour of gold. Higher galvanic currents were observed in two separate containers than that in one container indicating the primary importance of galvanic interactions. SEM-EDS results observed iron hydro/oxide coatings on gold surface in case of magnetite test. However, in case of RGO electrode it is not a perfect passivation, although somewhat decreasing trend was observed on gold dissolution. These findings have revealed that passivation is not only a laboratory phenomenon, but also it could be responsible for the slowdown of gold dissolution in industrial practice.INTRODUCTIONThe cyanidation of gold is an electrochemical corrosion process thus; the dissolution of gold can readily be studied by electrochemical techniques. The outcome/summary of previous electrochemical studies of gold leaching can partially be summarized as follows: Filmer (1982) and Lorenzen and van Deventer (1992) reported the negative effect of pyrite and pyrrhotite on gold leaching due to the galvanic interactions; Aghamirian and Yen (2005) studied gold galvanic corrosion in presence of sulphide mineral electrodes only in one cell using zero-resistance ammeter (ZRA) mode; Dai and Jeffrey (2006) discussed, individually, the anodic and cathodic behaviours between gold and sulphide minerals, and Azizi et al. (2010, 2011) used a bed reactor to examine the influence of sulphide minerals on gold dissolution in one and two separate cells. Accordingly, a slowdown in gold leaching has generally been attributed to the passivation phenomenon, although the indication of this phenomenon is still an undergoing debate. For instance, Mrkusic and Paynter (1970) identified the passivation as the film formation of dissolved species from calcine, Crundwell (2014) explained passivation, in the case of corrosion of metals, as the formation of a layer which is composed of a new chemical species on the mineral surface and this layer inhibits or blocks further reactions. He suggested that passivation is related to the oxidation of the metal, and the formation of a passive layer that retards the rate of dissolution by several orders of magnitude. Consequently, galvanic interactions, passivation phenomena, or combinations of them are considered significant electrochemical factors affecting gold dissolution (van Deventer, Reuter, Lorenzen, & Hoff, 1990; Azizi, Petre, & Larachi, 2012). It is important to note that generalizing the influence of a mineral/metal on gold dissolution may not be correct in all cases, since contrary behaviours/results (for pyrite) have been observed (Aghamirian & Yen, 2005). Therefore, electrochemical study of gold is still a subject of research and need to be examined further in detail."

Jan 1, 2016

By I. Protkova

Versa Power Systems solid oxide fuel cell (SOFC) stacks operate at intermediate temperatures 700 ? 800 °C allowing the use of metallic interconnects. Thermal expansion good matching with other stack components and cost restriction led to selecting ferritic stainless steels as interconnect material. Analytical tools and techniques were developed to understand the ferritic stainless steel behavior at high temperature while exposed to dual environment. Analytical tools such as X-ray diffraction (XRD), scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS) have provided valuable information towards describing interconnect degradation in a variety of testing conditions. Several examples are presented to demonstrate interconnect oxidation and its relation with SOFC testing results.

Jan 1, 2005

By Cristina Echavarría

MAIN POINTS ? The region: opportunities and limitations ? Overview of main issues emerging from MMSD in South America ? Who comprises the local community? ? What are the main challenges? ? Some suggestions for companies to improve their contribution to local sustainable development of mineral rich localities THE REGIONAL CONTEXT 1. The region is a producer of minerals contributing over 20% to world metal production. It consumes only 8% 2. Significant diversity of national contexts-both between countries and within countries 3. Variable but predominant need for strengthening of government and community institutions and governance, especially at the local level 4. Dearth of baseline information for decision making 5. Sustained social spending during early 90?s as a consequence of economic recovery and fiscal policy, produced important advances in education and health 6. Despite government efforts in most countries poverty continues growing 7. Highly inequitable distribution of wealth persists

May 1, 2002

By Z. S. Abisheva

The Zhezkazgan copper sulfide ore deposit in Kazakhstan contains both rhenium and the rare osmium isotope "osmium-187" (187Os) in the high isotopic purity of 99.4 ± 0.2%. This isotope is believed to have originated as a result of the disintegration of one of the rhenium isotopes, according to the reaction: 187Re75 ?> 1870576 + B- + v~ (where B is a 13-particle, v~ is a 3-disintegration antineutrino). The distribution of osmium and rhenium in metallurgical byproducts produced during the recovery of copper from these ores has been studied and process flowsheets for the processing of rhenium and osmium-containing byproducts have been developed.

Jan 1, 2007

By C. Ayora

The Iberian Pyrite Belt (SW Spain and Portugal) contains one of the largest reserves of pyrite in the world with mining activities dating back to prehistoric times. About one hundred abandoned mine wastes and galleries release a huge acidity and metal load to the Tinto and Odiel rivers. Once the mining activity is over, polluting discharges can persists for decades or even centuries with no specific responsible entity. In-situ passive remediation technologies are especially suitable for these orphan sites. The concept is to insert a reactive porous material in the natural flow path of contaminated surface and ground waters, and it is implemented through infiltration ponds and reactive barriers, respectively. Calcium carbonate pea-size gravel is the common alkalinity supplier to neutralize acidity and precipitate metals. These remediation systems have been traditionally implemented in coal mines. However, the acid drainages from the Iberian Pyrite Belt contain metal concentrations one to two orders of magnitude higher than those from coal mines and require special designs to avoid quick clogging or passivation (coating) of the grains of reactive material. To overcome these problems, a Dispersed Alkaline Substrate (DAS) mixed from fine-grained limestone sand and a coarse inert matrix (e.g. wood chips) was developed. The small grains provide a large reactive surface and dissolve almost completely before the growing layer of precipitates passivates the substrate. The high porosity and the dispersion of nuclei for precipitation on the inert surfaces retard clogging. However, limestone dissolution only raises pH to values around 6.5, which is sufficient to precipitate the hydroxides of trivalent metals (Al, Fe), but it is not alkaline enough to remove divalent metals. Magnesium oxide, which hydrates to Mg hydroxide upon contact with water, buffers the solution pH between 8.5 and 10. A DAS system replacing limestone with caustic magnesium oxide has been tested to be very efficient to remove divalent metals (Zn, Cd, Mn, Cu, Co, Ni, Pb) from drainage previously treated with limestone.

Aug 1, 2013

By Song (Bruce) Li

This paper presents a three-tier web-based GIS application that uses Java Server Page (JSP), Java Servlet and relational database to manage performance monitoring and reporting in the oil sands mining industry. It is a real-time Earth Structure Performance Monitoring System (ESPMS), which allows the user to record and store instrumentation monitoring readings as well as technical observations and instrumentation installation documentations into a complete relational database. The ESPMS introduces the advantages of precise field record keeping, due diligence, security, consistency and completeness while at the same time simplifying the task of reporting. ESPMS combines web-based Geographic Information System (GIS) mapping and data management to facilitate the collection, organization, retrieval, reporting and communication of the vast amounts of monitoring data related to mining and tailings engineering associated with site investigation and construction information. ESPMS utilizes web-based GIS technology to incorporate referenced aerial photographs, Energy, Mines and Resources (EMR) maps or AutoCAD drawings as a base map for the monitoring site. It dynamically creates and administers all instrumentation monitoring locations and reading frequencies. It enables the user to collect and manage the data associated with an unlimited number of reading events. It provides the designer with real-time monitoring data (what, why, when, how), thereby allowing them to make early adjustments to design protocols or procedures, or to take remedial action(s) regarding the subject earth structure under construction or after completion. It provides more cost-effective reporting and data sharing through the Internet. It improves security on data entry and eliminates unauthorized data changes. It allows better integration of graphics and illustrations with numerical data files. It is capable of managing the continually expanding workload resulting from new and larger structures in the oil sands or other mineral mining industries. The ESPMS facilitates easier data gathering for preparation of as-built and after-built or regulatory reports, etc. It enables quick location of the interested instruments and summarization of the performance of the instruments. It enables one to visualize performance data and QA/QC construction test results spatially on any given cross-section. Data can be exported to MS Excel for detailed analysis and to evaluate the stability of the earth structures.

May 1, 2004

By E. Burdukova

Long-chain primary amines are utilized as collectors in potash ore flotation. Krafft temperature of long-chain amines in brine is about 100 °C, and this makes such amines practically insoluble in brine at room temperature. When dodecylamine, melted at 70 °C and dispersed in hydrochloric acid (or acetic acid) aqueous solution, is added to a KCl-NaCl saturated brine at room temperature, the amine precipitates. The experimental results demonstrate that the precipitating amine hydrochloride particles are selectively abstracted by KCl particles, but not by NaCl particles.

Jan 1, 2009

By Poul Hansen

"In mid-1986, a world-class mining enterprise was created in Highland Valley, British Columbia, bringing together the copper mining operations of Lomex and Cominco . In 1988, Highmont joined the new partnership.Highland Valley Copper is the largest copper mine in North America in terms of both tonnage mined and tonnage milled, and it is one of the largest in the world. Due to its relatively low ore grade its production of copper in concentrate ranks about ninth in the Western World.The current eighteen year mine plan is based on ore reserves of 761 million tonnes. The daily milling rate is 133 000 tonnes. At the end of mine life, a total area of approximately 6500 hectares will have been disturbed. At this time, vegetation has been established on about 600 hectares and while work will be done during the operating years, it will not be until the end of mine life, about 2008, that the last half of the land can be reclaimed and revegetated.Once final reclamation has been accomplished, Highland Valley Copper will have completed its "" temporary use of the land"". In the meantime, about 1250people have had employment for about 50 000 man years, at wages ranking among the best in Canada.IntroductionTo provide and sustain our way of life, we need steel, copper, aluminum, zinc and many other minerals.To sustain mining, we must have adequate ore reserves and replacement of reserves as they are mined. Each year the search becomes more difficult as more of the Earth's surface is investigated and depo sits are mined. This calls for aggressive and sustained efforts.In British Columbia, past and present mining activities have disturbed less than one-tenth of one per cent of the land.With today’s technology, mining operations can be substantially reclaimed and thus complete the cycle of ""A Temporary Use of the Land""."

Jan 1, 1992

By M. Fairman

The effect of welding speed on the microstructure of friction stir processed (FSPed) AZ31B-H24 magnesium alloy was studied using light microscopy, image analysis, and microhardness tests. The grain size of the magnesium alloy was observed to increase after FSP from about 3.5 µm in the base alloy to about 8 µm in the stir zone. The aspect ratio decreased from 1.60 to 1.55 towards the center of the stir zone. The changes in the grain size and shape caused the microhardness of the samples to drop significantly across the FSPed region from 75 HV in the base alloy to below 55 HV in the stir zone. Decreasing the welding speed increased the grain size due to a greater input of heat energy. The faster heating rate due to the lower welding speed caused a deeper penetration of the annealing effects of FSP. It was also observed that the annealing effects caused by FSP were less pronounced with increasing distance from the interface between the sample and pin tool shoulder. The Hall-Petch type relationship of the micro-indentation hardness as a function of the grain size was observed to hold true after FSP.

Jan 1, 2007

By T. Grammatikopoulos, A. Jordens, C. Gunning

"Exploration activity for rare earth element (REE) deposits (i.e., alkaline complexes, carbonatites) has increased significantly in the last decade. A number of deposits have been evaluated around the globe. However, new mines have not been commenced in the last few years with the exception of Mount Weld (Lynas) and Mountain Pass (Molycorp).Resource estimation of REE can follow similar guidelines to other metal projects. However, the inherent mineralogical characteristics of the REE deposits, despite their complex nature, have been generally overlooked by many exploration companies. These include variability of the ore, liberation and association of the REE minerals, and grain size, all of which can affect the processing of the ore. Each deposit appears to be different in terms of matrix and REM (rare earth minerals). Light REE bearing minerals such as allanite, monazite, bastnaesite, synchysite, and HREE bearing minerals such as fergusonite and xenotime can vary widely in composition, grain size and association (e.g., carbonates or hard silicates). On the other hand, although not really REM, zircon, Zr-silicates, titanite, fluorite, apatite, and in some cases many other common silicate minerals can carry trace to significant concentrations of REE.The evaluation of REE deposits should include an appropriate mineralogical characterization in order to quantify the REM, distribution, liberation and association by quantitative mineralogical techniques (i.e., QEMSCAN, MLA, TIMA and others); chemistry of the REM by electron probe micro analysis (EPMA), Laser Ablation ICP-MS or ToF SIMS.These techniques provide valuable data for geological purposes such as: defining quantitatively, the variability and distribution of the REM; differentiating between LREE and HREE zones to delineate ore; and metallurgical purposes to predict minerals/REE behaviour during processing. The lack of a comprehensive mineralogical characterization often leads to the wrong processing path and ultimately affects the elemental/mineral recovery."

Jan 1, 2016

By C. Zangerl, W. Fellin, M. Holzmann, B. Hofer, S. Perzlmaier

"Four deep-seated rockslide systems were investigated and are under surveillance by TIWAG (Tyrolean hydro-electric Company) since the mid-1960s after impoundment of Gepatsch reservoir began. These rockslide systems consist of several individual sliding masses (slabs) which show variable activity from zero to a few centimetres per year. The focus in this paper will be on the findings for the transient deformation behaviour of the Hochmais slab which is part of the “Hochmais-Atemkopf” rockslide system.The rock mass has slid over moraine deposits in the last post-glacial period and was in equilibrium (or slow to extremely slow moving, respectively) until the filling of the reservoir began. During the initial reservoir filling in summer 1964 considerable movements had been observed over a length of 1000 m accompanied with an activation of the Hochmais slab. Geological investigations, additional surface and subsurface measurement showed that the sliding mass is characterized by an en bloc movement and the deformation accumulates within a several metre thick shear zone located within the moraine. In contrast to the deformation characteristics for the first impoundment process (1964 – 1966) where the magnitude of deformation occurred during impoundment, the maximum amount of deformation since 1967 occurs during the drawdown of the reservoir. Based on long term measurement it can be shown that the magnitude of deformations per year correlates with the minimum storage level in the reservoir. Other external influences such as precipitation and snowmelt have no observable impact on the deformation characteristic of the landslide. On the basis of long-term data series it was possible to determine the factors of influence and to elaborate a conceptual mechanical model which describes the transient deformation behaviour of the Hochmais slab induced by the drawdown of the reservoir. The mechanical model considers the reduction of uplift forces in the highly fractured and permeable rock slab during drawdown as well as increasing seepage forces in the less permeable moraine material."

Jan 1, 2015

Particles for heap leaching in conventional circuits are prepared using Cone crushers. Cone crushers are used to crush the ore to the size range between 12-25 mm for heap leaching operations. Leaching from these relatively coarse particles occurs only at the surface and in subsurface regions, which are accessible from the surface by cracks and pores. Since leaching is active in accessible areas, the method of comminution that forms multiple cracks and pores would offer an advantage for heap leach. An investigation was performed in this study to assess if the HPGR forms more cracks and pores than a Cone crusher. X-ray computed tomography (CT) was used to characterize the degree of cracks and pores formed by these two comminution devices that can be used for heap leaching feed preparation. In order to compare the effect of the comminution method on crack network generation, a bulk sample of the zinc ore was crushed by the HPGR at three different pressure settings (45, 95 and 120 bar), the sample ore was also crushed with a Cone crusher for comparison purposes. Products from the Cone crusher and HPGR experiment were then screened into five size fractions ((-25 +19), (-19+16), (-16+9.5), (-9.5+5), (-5+4.75) mm), Subsamples from the ((-25 +19), (-16+9.5), (-5+4.75) mm) size fractions were analysed. The spatial distribution of the crack network of sphalerite particles was characterized using a highresolution industrial X-ray CT system. This paper describes the use of image analysis techniques including image segmentation, which uses a combination of thresholding and other methods to characterize and quantify crack and mineral dissemination in the sphalerite particles after comminution with the HPGR and Cone crusher. The results are validated with those obtained using traditional techniques such as physical gas (with N2) adsorption, mercury intrusion porosimetry, SEM and QEMSCAN.

Jan 1, 2012

By W. Schubert, N. Radoncic

"The term “squeezing” is frequently used, although it is ill defined. Definitions like “large and long lasting displacements” raise the questions about the threshold values for the magnitude and duration of displacements. Large displacements during tunnelling frequently are observed in fault zones with high overburden. Whether this causes problems very much depends on the design approach used. On the one hand, the magnitude of expected displacements has to be predicted prior to excavation to provide for enough allowance for the displacements without violating the clearance profile. On the other hand, the support characteristics must be compatible with the expected imposed strains. As the magnitude of the displacements and thus the strains in the support depend on the support capacity and its characteristic (yielding potential), only well engineered systems will be successful.Experience in Alpine tunnels over the last decades has shown that closed shotcrete linings can sustain a strain of approximately 0.8% to 1% without failure. Any strain above this value inevitably leads to failure of the lining, and thus a loss of resistance, causing additional displacements. Based on a large number of simulations, a criterion for a critical overburden depth up to which closed linings can be used has been developed. Traditionally open gaps in the shotcrete linings have been used to allow for larger strains. To enhance the efficiency of the linings, yielding elements have been developed, which are integrated in the shotcrete lining, allowing large strains and controlled development of support resistance (Figure 2). When designing such yielding support systems, the development of the displacements, as well as the rheological behaviour of the supports must be considered. As the development of displacements to a large extent depends on the face advance, also the advance rate has to be considered, to be able to compare the time-dependent strength of the lining to the stresses developing as a result of the imposed strains. Another issue is the compatibility of the rock bolts with the large strains. With standard grouted bolts, there is a potential that the “fresh” grout is sheared due to the initially large strain rates. Special rib designs of the bolts allow for a higher strain tolerance.For successful tunnelling through fault zones quality monitoring and up-to-date data evaluation is of crucial importance. With advanced evaluation tools, changes in the ground conditions ahead of the face can be reliably predicted. With the help of empirical relations, the development of the displacements for different advance rates and supports can be predicted, allowing for the determination of the required overexcavation.The paper presents a review of the development of ductile elements, methods of analysis, and monitoring data interpretation."

Jan 1, 2015

By G. K. Quainoo

Investigation by researchers on the application of various thermo-mechanical process histories on 6000 series aluminum alloys have found improvements in mechanical properties of these alloys. However, natural aging, which is unavoidable in the automotive processing line, has been found to have deleterious effect on subsequent artificial aging properties in these alloys. In this study, the evolution of yield strength during natural aging modeled by Lloyd and Gupta has been adapted to investigate the effect of cold deformation on the natural aging kinetics in AA61 11 by means of tensile testing, differential scanning calorimeter (DSC) and scanning electron microscopy (SEM). Also, intermetallic particles in the alloy were extracted from the matrix and XRD performed on them to ascertain their composition and their role on the kinetics in the alloy. The results show that cold work effect on the natural aging kinetics of AA6111 is in very good agreement with the model proposed by Lloyd and Gupta. The kinetics of natural aging in AA6111 aluminum also decreases with increasing level of cold work. This is attributed to dislocations serving as sinks which consume quenched-in vacancies formed during the early stages of clustering. The phases of the intermetallic particles identified in AA6111 are those of a-A15Mn12Si7 and a-A15MnSi.

Jan 1, 2007

By Karl J. C. Harries

"The following is an outline or check sheet of some things that might be looked at when considering the concept of a royalty or royalty provisions. It is not intended as a guide to what is right or wrong (that is for the parties to decide). It does not replace the discussions in this work and is not intended to be a complete or exhaustive compilation of matters to be considered. It presumes that you are familiar with the basic concepts of royalties and has been included as an aide memoire only. Use it as such, with caution and common sense, and amend it to suit your needs. Remember also that brevity can result in inaccuracy or imprecision. This is a danger in many points below.The section references are for the sections where the matter is the main subject of the section – see the index for other sections.Royalty TypesNet Proceeds [§§ 5.8.; 11.4.]• No accepted or understood meaning within industry.• Literal meaning, if not defined, would imply “net operating profit”.• Often defined as net profit with revenue base of proceeds from sale of product.• Should not be used without detailed and clear definition. Net Operating Profit [§§ 5.8.; 11.4. – referred to only]• Net profit without recoupment of pre-production expenditures.• Revenue base: usually proceeds from sale of product.• Operating costs deductible.• Some reserves may be permitted.• Recoupment of some post-production capital expenditures may be permitted.• Not often seen as basis for royalties in Canada."

Jan 1, 2003

By Barton G. Stone

The mining and exploration industries have been using Geostatistics (Matheron, 1963) for the past forty years. It has been extensively incorporated into three dimensional block modeling software whose usage has reflected the growth in the use of personal computers since 1980. Because of the utility of geostatistical models in mining and production planning, much of the modern reserve and resource modeling is done by mining engineers, geostatisticians and geological engineers. Explorationists are initially less concerned with three dimensional models until such time as a deposit has been roughly delineated. However, the concept of regionalized variables in ore deposits deals with the effect of spatial correlations between data points in a three dimensional sample space and should be useful for optimizing the spacing of drill holes to allow maximum bang-for-the-buck in drilling programs. This paper examines three common deposit types (porphyry copper, VMS and intrusive gold) to examine whether geostatistical methods have been used to minimize drilling costs because of better understanding of spatial correlations. The three model types were chosen from publicly available corporate websites of Canadian based Junior Mining Companies. They include the Wolverine polymetallic zinc deposit of Yukon Zinc in Yukon, Canada; the El Morro Deposit in Chile (30 percent ownership by New Gold Mining Company, and the Fort Knox Gold deposit in Alaska and 50 percent ownership by Nova Gold Resources). Typically, individual mining corporations post their technical reports as CNI 43-101 reports on their corporate website as indications of the favorability or progress on their more exciting properties. Data considered for this paper was not collected or generated by the author, but the information was extracted from these publicly available sites and had a variety of authorship.

Oct 1, 2009

By Mark Sherman

One of the main functions of a process technology and engineering services provider is to select grinding equipment that will meet the client?s throughput rate target. Prudent risk mitigation strategies would suggest that throughput rate estimates be cross-checked using a variety of techniques. Whilst some comminution circuit designers have estimated specific energy requirements via the manipulation of the Bond specific power equation e.g. Barratt?s Grindpower and OMC?s FSAG approach, other designers have opined that the Bond Indices have no role to play in the calculation of SAG mill specific power. As a result, they have developed their own specific energy estimating methodologies, e.g. SMCC?s Drop Weight based power methodology, SPI, SAGDesign, etc. Each method has its supporters and its critics. The challenge facing the engineering provider is how to nominate an SAG mill based circuit throughput rate estimate when faced with significantly disparate specific energies calculated by the different methodologies. This challenge is exacerbated via the continuing evolution of contemporary circuit configurations such as two stage pebble crushing some of which incorporate HPGR technology as the second stage of pebble crushing. The methodology presented in this paper shows that the Bond Indices are an excellent tool for estimating the specific energy requirements for SAG mills in SAB, SABC and SSS circuits. The method accommodates primary crushed feeds, partial and or fully secondary crushed SAG mill feeds, and emulates the impact of pebble crushing on SAG specific energy. As a result, the new Bond Index based method has provided an additional tool for increasing Fluor?s confidence when predicting SAG mill based circuit throughput rates. Based on this outcome, the author proposes that the decades old conundrum of using Bond Indices to calculate SAG specific energies for SAG mill based circuits has been solved.

Jan 1, 2012