Search Documents

By E. H. Mulligan

THE ERRINGTON B-I mine is located on the Errington orebody of Steep Rock Iron Mines, Limited, at Steep Rock Lake, Ontario. In 1946, this orebody entered the shipping lists of the Lake Superior iron ranges as an open-pit operation. During the period 1946 through 1953, the mine produced a total of 9,000,000 tons of iron ?ore. In 1950, as the mine approached the economic limits for open-pit operations, ground was broken for an underground development to exploit the deposit at depth. The mine is designed for an ultimate production of 1,500,000 tons per year by the block-caving system of mining. The initial shaft is 1,200 feet deep and will produce or-e from the 700 and the 900 levels. The 1,100 level will be used as a drainage level and as a haulageway for waste rock, which is hoisted to surface by skip. Ore from the two production levels moves by a system of ?ore passes to a crushing plant located below the 900 horizon and is hoisted from this point to surface by conveyor belt. At the present time, all material handling on the levels is by tramming, but as tram distances increase conveyor haulage will probably be installed. The initial stage of the Errington B-1 development is expected to produce 6,000,000 tons of ore over a period of four years. The second stage will require deepening of the shaft and development of lowe1? production levels. The conveyor hoisting plant will be extended to serve these new levels. We visualize the mining of this orebcdy down to 2,500 feet by these methods.

Jan 1, 1956

By J. Kramer, T. Hartmann

In the Hydrometallurgical processes, the presence of the so-called “crud” is a constant challenge in solvent extraction. Crud is a stable emulsion which forms along the interface between the aqueous and organic phase. The spread is influenced by the following parameters: first, wind blows the dust and impurities into the open sedimentation tanks. Second, the undissolved solids such as sand transported in the PLS causing problems in conjunction with incorrect agitator design. The crud fraction can decisively impact the efficiency of the hydrometallurgical extraction because the phase interface can constitute a large fraction and the sedimentation tanks cannot react flexibly to it. In the downstream process of the seriesconnected sedimentation tanks, they are thus all contaminated with crud. At the same time, the necessary mass transport is significantly impeded at the phase boundary between organic phase and aqueous phase due to the crud formation. The transfer of the organic phase into the electrolysis cell can result in a “burnout” of the cathode. The carry-over of this electrolyte into the extraction can cause problems with the pH regulation. The carry-over of the organic components into the raffinate also leads to contamination of the leaching circuit. The continuous treatment of the crud with a 3-phase decanter centrifuge is extremely effective in combating this problem. This technology splits all three phases from each other and they are consequently continuously separated. All subsequent process steps exhibit a stable, uniform effectiveness. The main advantage for the customer is that fluctuations in the process are eliminated and the organic phase can be recirculated back to the extraction. The recycling of the solvent alone justifies the investment in less than 6 months as examples from South Africa and Chile show. To operate solvent recovery in daily operation fully automated online at the optimum limit, the decanter centrifuge is equipped with a concentration-dependent pond adjustment called DControl®. By this means, we can guarantee our customers the maximum possible solvent recovery and minimise the solvent costs in this process step. This system is presented in detail in this paper.

Jan 1, 2012

By Robert D. Brown

"On April 22, 1980, the Ontario government introduced a totally new incentive program for mineral exploration in the province to be effective September I, 1980. Replacing the former Mineral Exploration Assistance Program (MEAP) and also the assistance formerly provided to the mining sector under the Small Business Development Corporations Act, the new Ontario Mineral Exploration Program (OMEP) promises to offer a valuable benefit to certain eligible applicants.Unfortunately, the program is not without its shortcomings: the eligibility for grants or tax credits under the program is comparatively restrictive, and an October 1980 federal budget provision to amend income tax legislation would blunt some of the originally intended attractiveness of the grants and credits.IntroductionIn his budget of April 22, 1980, Ontario Treasurer Frank Miller introduced a new incentive program to encourage mineral exploration in the province.The Ontario Mineral Exploration Program (OMEP) replaces the Mineral Exploration Assistance Program (MEAP), which will be phased out by March 31, 1981. Exploration programs approved under MEAP will continue to qualify for incentives under that program, but will not qualify for OMEP."

Jan 1, 1981

By C. Boudreault, M. Fortier, S. Fafard

In the forging industry, the increasing trend is to use DC cast billets as forging stock to replace extruded stock. However, there is little technical information available in open literature. In order to gain a better understanding of the behaviour of cast stock during deformation, a study was initiated to evaluate the impact of an homogenisation treatment on the billet prior to cold forging. Axisymmetric upsettings of cylindrical samples machined from DC billets were achieved in order to evaluate and compare flow stresses, crack initiation and propagation. Results show a 30% decrease in flow stress after homogenisation. Observations of the deformed samples show major cracking for the as-cast material. Optical microscopy and SEM observations have related the crack initiation to decohesion around ß -AlFeSi particles and subsequent growth along the constituent path. Homogenisation effectively breaks up and transforms the ß phase, present as platelets in the cast product, into smaller spherodised a-AlFeSi particles. This has the effect of preventing crack growth in the forged product. The homogenisation treatment also resulted in the reduction of Mg and Si in solid solution. The softer matrix generated 29% less die wear when compared to the as-cast structure. Based on the results of this study, it is thus recommended to homogenise cast billets prior to cold forging.

Jan 1, 2006

By K. D. Bulin

"An interesting brief history review of shovels as the primary excavating tool will permit the reader to see that immeasurable development and resources have preceded the shovel excavators which today are used extensively throughout the mining industry. With this as a background, the shovel manufacturer has the ability to utilize his resources best in those areas of shovel development in which the maximum benefits of increased reliability, performance and ease of maintenance will improve the operating rewards to the user of the equipment. The author explains the function of the shovel as a part of the material handling system. A detailed description of those areas of the shovel in which the most recent developments and major improvements have been implemented in the manufacture of the shovel excavator arc included."

Jan 1, 1973

By H. Higuchi

The Sumitomo Metal Mining Company Ltd. (SMM) started to produce electrolytic nickel at the Niihama Nickel Refinery in 1939. In 1992, the conventional matte electrorefining process was converted to the matte chlorine leach electrowinning (MCLE) process, which is currently in practice. SMM has mainly used two kinds of nickel matte as the raw material for the MCLE process. Treatment of new raw materials, which have different impurity contents from the original nickel matte, has become mandatory because of changes in the market. Therefore, the MCLE process has been required to increase its flexibility to treat the different impurity contents in the new raw materials. An increase in the capacity for iron removal is included in such requirements. A new iron removal circuit in the MCLE process, based on a process development study, was recently installed. The iron removal circuit is in operation, and efforts are currently underway to optimize the performance of the circuit by changing the present operating parameters. In addition to the removal of the iron, the application is also expected to improve the nickel recovery. The outline of the new circuit and the current iron balance in the MCLE process are described in this paper, together with the effect of the circuit on iron treatment capacity.

Jan 1, 2006

By L Gill

The four basic types of electric motors -squirrel-cage, wound rotor, synchronous and D.C. -are de-scribed, with particular reference to speed-torque characteristics. The three classifications of squirrel-cage motors, C.E.M.A. B, C and D, are compared, and methods of selection for specific drives are outlined. Wound rotor and synchronous motors are covered from the viewpoint of construction details, methods of operation and control required. The application of these motors to crushers, conveyors and ball mills is described and reasons for their selection are given. The application of D.C. motors to haulage equipment and mine hoist drives is included, and the basic principles of a variable voltage drive are illustrated. Efforts have been made through-out to provide specific examples of motor selection, with particular reference to the mining industry. THIS paper will attempt to answer the question -"which motor should be used for a specific drive?" Although it is impossible to cover the complete subject of electric motor application here, we hope to give some idea of the types of motors available and why certain types are used on specific applications.

Jan 1, 1963

By E. A. Morris

It has been shown that Alberta oil-sands fluid coke can be effectively used to reduce SO2 to elemental sulphur while simultaneously producing sulphur-impregnated activated carbon (SlAC). In the capture of mercury from industrial flue gases, SIAC has proven to be a highly effective adsorbent material. The current research aims at developing an existing SlAC technology to meet the needs of copper smelters for mitigating both mercury and SO2 emissions, while making elemental sulphur as a co-product. The challenge behind this undertaking is that these flue gases generally contain percent levels of 02 and H20 vapour (2-12%). The focus of this study is therefore on the feasibility of reducing SO2 using fluid coke under copper smelter flue gas conditions, as well as the optimisation of SIAC properties for capturing vapour phase mercury. It is hypothesised that mercury capacity is strongly affected by the 02 potential of the activation gas due to changes in surface sulphur types arising from different reduced sulphur species. To verify this, gas chromatography is used to analyse the reaction products while XPS and XANES will be used to describe the nature of sulphur on the SlAC surface. CVAFS analysis of mercury capacity will finalise the hypothesis assessment. Preliminary results indicate that 02 at 5% does not play a significant role in SSA or pore development. As expected, increased residence time contributes to SO2 reduction and elemental S yield.

Jan 1, 2007

By B. Dyck, L. Verhelst

"Colloidal silica in Key Lake’s Solvent Extraction (SX) feed solutions has presented an operational problem for the mill throughout its history. The colloidal silica stabilizes aqueous continuous emulsions, resulting in elevated solvent losses and operational downtime. Through the years, many attempts have been made to solve this problem, but no viable solutions were found. By revisiting an idea dating back to the 1979 feasibility study and re-evaluating it under current operating conditions, a practical solution was achieved. This paper discusses Key Lake’s history around colloidal silica removal, starting with coagulation using a polyethylene oxide polymer (PEO), and ending with coagulation using a polyethylene glycol (PEG) polymer. The results of a mill trial using POLYSIL® RM1250 introduced at doses up to 300 ppm into the counter current decantation (CCD) circuit to clarify SX feed solutions are discussed with a focus on the benefits to SX.INTRODUCTION Colloidal silica has historically been a significant operational problem in the Key Lake mill. Silica originates from clays in the ore as well as concrete backfill intermixed with the ore resulting from the mining method used at Key Lake’s ore source, the McArthur River mine. The silica is dissolved as silicic acid into solution in the mill’s sulphuric acid leaching circuit. Once in solution, silicic acid polymerizes (Hearn, Smethurst, & Boskovic, 2016) forming a fine suspension of stable colloidal particles. These silica colloids are unaffected by flocculants and sand filtration reporting to the pregnant leach solution (PLS) as a fine turbidity in solution. Silica concentrations typically ranged from 700 to 1200 mg/L Si in the PLS fed to SX. Throughout Key Lake’s history, silica interactions in the Solvent Extraction (SX) process have made SX a mill bottleneck and a source of significant reagent costs."

Jan 1, 2018

By L. Kong, V. G. Papangelakis, L. Li

"The Eh-pH diagram of lithium-titanium-water system at 25°C, 100 °C and 200 °C was constructed. It shows that there exist thermodynamic stability areas of Li2TiO3. This indicates a thermodynamic possibility for the formation of Li2TiO3 in aqueous solution. A hydrothermal process has been applied for the preparation of Li2TiO3 using TiCl4 and LiOH•H2O as raw materials. The prepared samples were examined with X-ray diffraction, scanning electron microscopy and thermo-gravimetric analysis and differential scanning calorimetry. The results show that temperature and washing condition have significant effects on the phase composition of the product. Phase-pure Li2TiO3 powders were obtained at 200°C with Li:Ti molar ratio of 2.0.INTRODUCTIONLithium-containing ceramics enriched in 6Li, such as Li2O, LiAlO2, Li4SiO4, Li2ZrO3 and Li2TiO3, are considered as tritium breeding materials (Saito et al., 1998; Roux et al., 1998; Johnson et al., 1998; Hoshino et al., 2002). In view of its admirable properties: low-activation, good thermal stability and thermal conductivity, excellent tritium release performance and reasonable lithium atom density (Kopasz et al., 1994; Roux et al., 1996; Saito et al., 1998; Wu et al., 2008), Li2TiO3 is recognized as one of the most promising candidates of tritium breeding materials. Meanwhile, Li2TiO3, as the precursor of H2TiO3-type lithium absorbent, receives more attention as the development of extracting lithium from salt lakes (Zhong, 2004; Zhang, 2010).Several synthetic techniques have been applied to prepare Li2TiO3 powders, such as solid-state methods (Lulewicz and Roux, 2002; Ramaraghavulu et al., 2011; Mandal et al., 2012), sol-gel processes (Deptula et al., 2002; Lee, 2008) and solution combustion routes (Cruz et al., 2006; Jung et al., 2006; Sinha et al., 2010). A solid-state method may produce a series of problems, including impurity contamination and difficulty in morphology control of the obtained powders, although the process involved is simple. The solgel process is prolonged and usually demands for multi-step reactions, while solution combustion route requires plenty of energy and easily causes product contamination by the fuel used. Owing to its environmentally benign and highly suitable characteristics in fabricating materials, hydrothermal technology has been widely used and became a powerful tool in the field of material synthesis (Yoshimura and Byrappa, 2008). For example, ZnO in the form of bulk single crystals, fine particles and thin films, which is an attractive photoelectric material, was successfully synthesized by hydrothermal process (Sekiguchi et al., 2000; Ohshima et al., 2004). A hydrothermal technique was also used to the preparation of carbon nanotube, which possesses outstanding mechanical, structural and electric properties (Bernholc et al., 1997), and is superior to the commonly used method (Gogotsi and Libera, 2000). There, it provides an option for preparing Li2TiO3. Laumann et al. (Laumann et al., 2010) synthesized cubic a-Li2TiO3 by hydrothermal reaction at 180 °C for 18 h, using TiO2 powder, comprising of anatase and rutile, and lithium hydroxide in de-ionized water. However, the prepared a-Li2TiO3 is extremely unstable with a maximum lithium loss of 75% when treated in bathing experiment."

Jan 1, 2012

By K Komori

Naoshima Smelter and Refinery has treated shredder residue and incinerator fly ash in Japan since 2003. As a highlight, a new incinerating and melting furnace, as well as fly ash washing treatment plant were newly constructed for pre-treatment of shredder residue and fly ash respectively, and the pre-treated materials are ultimately treated in the existing Mitsubishi continuous copper smelting and converting process line. Since wastes such as shredder residue tend to vary in size and in shape, and contain some chlorine, the installation of a new pre-treatment line was required. The combination of the new pre-treatment line with the existing Mitsubishi Continuous Copper Process line has created a highly efficient and environmentally friendly system for recovering and recycling of valuable metals that previously used to be sent to a landfill. This paper reviews the approach that Naoshima took to establish its current recycling business strategy.

Jan 1, 2007

By R. D. H. Wigmore

"The title of this paper probably sounds quite simple and self-explanatory. The problem, however, was not a simple one, and proved somewhat baffling and expensive over a period of years. After outlining the problem, and the methods which were used to overcome it, we will present our solution, or perhaps it would be more accurate to say the partial solution which we reached.We have in the cyanide circuit at Upper Canada two Dorr Single Tray Thickeners with 30 ft. diameter wood stave tanks 12 ft 4 1/ 2 in. deep. In the years prior to 1948, when the tonnage was 250 to 280 tons per day, two stage thickening was practised. As the tonnage was increased to 450, 500, and finally 560-600 the thickeners were used in parallel.Some settling problems were encountered, and in those days the means to combat these problems were very few. The only remedy was to dump in pounds and pounds of lime. Then along came a few reagents, and the writer remembers one in particular, - 11 Carboxel11 (carboxymethlycellulose). When water or solution was added to this reagent, the result was a gooey mass somewhat resembling tapioca. One drawback was that it stayed in this state, and didn't go anywhere. A method was finally developed of containing the mass (or mess) on a fine screen, and dissolving some of it was a fine spray of solution. The only thing the writer recalls was that it was not a very effective settling agent.Shortly after this time, along came the new flocculents, first a few, and then many, and our settling problems were over.But when the settling problem was solved at Upper Canada, some other problems were creeping up on us."

Jan 1, 1965

By C. A. Anderson, C. A. Young, H-H. Huang, L. G. Twidwell

An equilibrium calculational computer program (STABCAL) can be used for titration simulation. The program can handle various forms of titrants: solid, aqueous, gaseous or another solution, and various type of reactions: reductive, oxidative and adsorption. Background chemistry, mathematical considerations, and program development will be illustrated. Also, simple titration applications such as how to determine the acidity of aqueous solutions and alkaline sulfide leaching of gold are presented. Processing of an acid mine water from the Berkeley Pit in Butte, Montana has been used for illustration purposes. The treatment studies included: cementation, sulfidization, and neutralization. The calculational results for the neutralization treatment using various alkaline reagents are compared to actual experimental data and potentially appropriate processes are discussed. Computational

Jan 1, 2005

By R. H. Nafziger

A novel process has been developed for preparing directly workable steel ingots from prereduced iron ore pellets by a two-stage process. The pellets are continuously charged into an electric arc furnace, where molten metal is separated from the gangue. The molten metal flows out of this furnace through a hollow nonconsumable graphite electrode immersed in a molten flux in an electroslag furnace. The molten metal solidifies on a continuously withdrawing base plate to form the ingot. A variety of standard carbon and alloy steel ingots . free of porosity , were produced using suitable decarburizers and ferroalloy additions. Some advantages of the two-stage process include: (a) consumable electrode fabrication is eliminated; (b ) no expensive deoxidizers are required; (c ) the uncontaminated electros lap flux can be reused; (d) energy consumption averages 25% less than in a conventional electric arc - electroslag operation ; and (e) the operation is continuous.

Jan 1, 1977

By M. S. Alam, Jae-Chun Lee, M. Tanaka, K. Koyama

Extensive research work is being carried out at AIST for developing energy saving green technology for base and precious metals recovery. In the present work, a new flowsheet is developed for copper recycling from waste electronic circuit board where copper was recovered by leaching followed by solution purification and direct electrowinning of Cu(I) from ammoniacal alkaline solution. In this new technology, power consumption in EW circuit was greatly reduced. This paper describes the overall process with an emphasis on different aspects of solution purification where impurities were selectively removed by cementation and solvent extraction techniques under nitrogen atmosphere.

Jan 1, 2004

By S. Demetrio

China has a traditional segment of Copper Smelters with its own Chinese technology, typically small in size from 20.000 to 50.000 tCu/a, and they are responsible for the processing and production of more than 600,000 tonnes of blister copper per year. For occidental experts, like one of the authors, it is not so easy to believe that they are profitable, because the size and the use of old Blast Furnaces, but they are with simple and effective production lines. The authors are convinced that China has a good alternative to improve theses old copper production lines with small innovative changes in its process arrangement, jumping to higher level technology, more efficient in production, productivity and cost, assuring copper as a raw material for the country and its high speed development. The key to improve that the traditional Chinese Copper Smelter is white metal as an extra raw material as a first step doubling the copper production from raw materials and the complete replacement of concentrates by white metal (WM) in a second step increasing it four times or more as the final goal. It is not so difficult nor expensive to make it happen, but there are a couple of questions for implementing this innovation in the copper smelter industry: 1 - Will the old fashioned mentality be open to this new direction for China being the biggest copper consumer on one side, and the biggest copper Primary Producers on the other hand? and 2 - Will they be open to follow this "win-win" strategic way for both ends of the copper market? We don't know if anybody will take up the challenge to improve it but our responsibility as a consulting expert and a university professor is to put the alternative on table for others to decide whether to implement it.

Jan 1, 2007

By J. J. Jonas, G. R. Stewart, N. Pokutylowicz, S. Yue, R. Varano, A. Elwazri

Differing thermal histories in and around a weld can lead to differences in grain size, phase composition and morphology of precipitates; mechanical properties will vary accordingly. Hardness testing gives limited information and the machining and testing of tensile and/or impact specimens that would reveal these variations (which may occur over very small distances) is not practical. Therefore, in this investigation, shear punch testing was applied to measure the variation in the room temperature mechanical properties of a welded pipeline steel.

Jan 1, 2005

By R. H. Andrews, F. J. West

"Jones & Laughlin Mining Company, Ltd. operate the Adams mine at Kirkland Lake, Ontario, where they mine approximately 4,000,000 tons of extremely hard iron-formation and 3,500,000 tons of volcanic waste rock annually in order to produce 1,100,000 tons of iron pellets. This paper will discuss the maintenance of the four Model 1600 P & H shovels and the two 50-R drills used to obtain this production. The chief maintenance problems at the mine are due to the hard, abrasive ore and the cold winter weather."

Jan 1, 1970

By M. M. C Jiménez, D. C. Buzzi, D. C. R. Espinosa, J. A. S Ténorio, G. F. R Oliveira

In this work the extractive and selective capacities of solvent extraction synergistic systems to recover nickel and cobalt were evaluated. The liquor used was from the high pressure acid leaching process (HPAL). Initially the industrial liquor, processed from lateritic ores, was analyzed to identify the concentrations of the metals. Experiments of synergistic solvent extraction were performed later. The extraction liquid-liquid was carried out with a mixture of Cyanex 272 (CY) and Ionquest 290 (IQ) extractants. The process was executed with the temperature of 65 ºC, pH of 5.2 and the ratio aqueousorganic 2:1. Systems of 80% kerosene and CY 20%, CY 16% - IQ 4%, CY 12% - IQ 8%, CY 8% - IQ 16%, CY 4% - IQ 16%, IQ 20% were studied during 20 minutes. The results of this paper showed that the mixture of these two extractants doesn’t improve significantly the recovery of nickel and cobalt from liquor.

Jan 1, 2014

By Jean-Jacques Bouillon, Michel Jébrak, Stephane Faure

"Le gisement polymétallique (Cu-Zn-Au-Ag) des Mines Selbaie est forme par un réseau de filons encaisses dans une séquence de pyroclastites felsiques du sill on Harricana-Turgeon. Les minéralisations sont encaissées dans le tuf de Selbaie, situe sous une épaisse séquence d'ignimbrites Iitées. Ce gisement se distingue des autres gites archéens par une chronologie atypique des minéralisations: les veines de chalcopyrite, de sphalérite et de galène recoupent un amas exhalatifpyriteux stérile. Un vaste halo d'altération hydrothermale a chlorite et mica blanc est associe à cette minéralisation.La mise en place des veines minéralisées est associée à une phase d'extension NNW-SSE. Le complexe volcanique subit, par la suite, trois phases de déformation. Une compression, orienté N-S, développe une schistosité à peine pénétrative et un réseau de fentes de tension. Une réorientation des contraintes locales selon une direction WNW-ESE conduit au chevauchement de I' écaille d'andésite et de tonalite de Brouillan. Un réseau conjugue de failles normales cassantes est associe au relâchement des contraintes."

Jan 1, 1990