Search Documents

By Shek N. Lau, Nicola Samman

"Enclosed gear cases on board heavy mining equipment have traditionally been lubricated with regular heavy duty gear oils. However, equipment manufacturers, have recommended the use of an ISO-1000 gear oil for this application to ensure adequate lubricant film strength, especially at the higher end of the working temperature range. The majority of these ISO-1000 gear oils are based either on residual/asphaltic oil or synthetics, primarily higher viscosity polyalphaolefins. Although the performance of these lubricants has been satisfactory, they suffered other shortcomings that equipment users have lived with over the years.The major requirement at the user’s mine was to provide lubrication for the shovel Hoist gear case. Within such a gear case design, the gears and the roller bearings, that have different lubrication requirements, are lubricated with the same lubricant. Several lubricants were used, light gear oils as well as the recommended ISO-1000 heavy gear oils. On the one hand, the lighter oils performed adequately for the lubrication of the bearings that formed part of the enclosed gear system. These lighter oils did not perform as well for the lubrication of the gears due to their lower viscosities, resulting in shorter gear servicelives.On the other hand, the ISO-1000 gear oils performed well for the lubrication of the gears, but were too viscous to creep into the bearing elements to lubricate them adequately, especially during the cold northern Canadian winters. This resulted in catastrophic bearing failures and secondary damages to the gears.The challenge, then, was to formulate a lubricant which met the 1000 cSt at 40°C viscosity requirement as stipulated by the equipment manufacturer, while satisfactorily lubricating the bearings at the full working temperature range. This was achieved by the development of a semi-fluid grease lubricant, which has proven in field trials to give adequate performance in this application for the lubrication of both the bearings and gears down to -40°C.This product met the equipment manufacturer’s performance criteria and resolved, to a large extent, leakage of the lubricant through seals experienced with the use of conventional and synthetic gear oils.Although the main performance criteria of the fluid was its capability to lubricate the “Hoist” gear case, it was also used during the field trial in other gear cases on board the shovel to test its full capabilities.This unusual alternative lubricant was field tested and evaluated for more than two years. Based on this assessment, the product was reformulated to improve its fluidity, slumpability and the settling of debris/wear metals to the bottom of the gear cases. This reformulated softer grade, a semi-fluid grease, has been performing satisfactorily for more than eight months and is still undergoing longer term assessment."

Jan 1, 1996

By D. Gorc, T. M. Fraser, Z. T. Nikic, R. Pesalj

"Mount Polley is an alkalic porphyry copper-gold deposit of Lower Jurassic age within the Quesnel terrane in south-central British Columbia. The silica-saturated Mount Polley intmsive complex is assumed to be coeval with volcanic rocks of similar composition in the Nicola Group in which it was emplaced. Other intmsions and some of the volcanic rocks in the Mount Polley area are silicaundersaturated and contain feldspathoids.The Mount Polley deposit is characterized by multiple intrusions that vary from diorite to crowded plagioclase porphyry to monzonite. Intmsion breccias are associated with some of the intmsive phases. Abundant hydrothermal breccias occur on the margins and above plagioclase porphyry intmsions. These breccias provide the main host for mineralization and are associated with the highest concentrations of copper and gold. The breccias are subdivided into four distinct types based on the dominant hydrothermal mineral in the matrix. Actinolite breccia is developed in an elongate zone within the core of the Central zone and grades laterally and vertically into biotite breccia to the southeast. Magnetite breccia is irregularly distributed and is relatively sparse throughout the deposit and albite breccia is dominant in the West zone. Pervasive and vein-related alteration correlates with the breccia types. The core of the hydrothermal system at Mount Polley is subdivided into three zones: actinolite, biotite and K-feldspar-albite. The margins of the core zone are overprinted by a discontinuous zone of calc-silicate minerals. This intermediate zone passes outward into propylitic alteration. Mineralization is most prominent within hydrothermal breccias and is generally present as disseminations, blebs within the matrix and abundant veins. Mineralization is associated with a chalcopyrite-magnetite-bornite assemblage in the core of the deposit passing out into magnetite-pyrite-chalcopyrite. Relatively constant copper to gold ratios suggest that both metals were precipitated under similar conditions.Hydrothermal breccias are genetically related to the emplacement of the crowded plagioclase porphyry melt. Crystallization of the melt was probably accompanied by volatile/aqueous exsolution, forming a water saturated carapace. Decompression of the chamber in response to magma withdrawal, fracture propagation and possible fault movement allowed hydrothermal brecciation to occur at the apex and margins of the intmsion. Alteration and mineralization appears to have been controlled by fluids migrating away from the plagioclase porphyry."

Jan 1, 1995

By C. M. Campbell

IN 1934 Newfoundland, after extravagant operation based on exaggerated ideas of what she had to work with, became bankrupt, ceased to be a self-governing Dominion, and passed into the hands of a Commission. Since the days of Dawson, Canadians have been taught that no country in the world is as rich as their own. This idea has become a religion; contrary views are heresy, and are suppressed even by technical organizations and government departments. Following the alleged habit of the ostrich, we have buried our heads in the sand and have refused to face the facts. This policy of "to have today and to hell with tomorrow" is now bearing fruit. After forty years of operation on the basis of unlimited natural wealth, with resulting over-expansion, wholesale depletion of capital assets, and huge borrowings, we are, now that our wealth has been shown to be very limited, face to face with the status of Newfoundland. Already, in this Province, commission government of bankrupt municipalities is not uncommon. The ostrich is referred to as the most foolish bird in the world. That is not the case-no ostrich ever hid his head in the sand. In the clear air of his home on the South African veldt, an area characterized by low bushes, he is a conspicuous object. When danger approaches, he lowers his head; matches his background, the bushes; and danger passes him by. This leaves the Canadian, with his head still in the sand, to fill the r61e cast for the ostrich. Fortunately, a few Canadians never did get their heads covered; others are getting them out far enough to see what is going on. Their comments are very much to the point. "Nowhere in the world," says Mr. Meighen, "has more harm been done to any country by an exaggeration of its resources and potentialities than has been done in Canada'.

Jan 1, 1941

By B. K. Mishra, P. Patnaik, B. C. Tripathy, I. N. Bhattacharya

Cobalt is an essential metal considering its numerous industrial applications. The demand for the metal is increasing due to its wide range of use in, for example, rechargeable batteries and as an alloying element in super alloys. Cost effective production of Co is critical. Electrowinning from aqueous sulphate solutions is the preferred technology available for the production of Co. Attempts are being made to produce uniform, smooth and bright deposits of cobalt metal. Use of organic additives in the electrolytic bath improves current efficiency and deposit morphology of the metal. We investigated the effect of quaternary amines TEABr, TPABr and TBABr during cobalt electrowinning from aqueous sulphate solutions. Among the additives studied, TEABr yielded the best results. Smooth and bright deposits of cobalt were obtained at low concentration of TEABr (10 mg/L) maintaining a very high current efficiency of 99.6%. X-ray crystallography indicated that (100) is the most preferred plane of crystal growth.

Jan 1, 2014

By D. Sharma, A. K. Singh, R. Singh, P. K. Mandal, M. Sarkar

"This paper deals with the stability investigations carried out at the XIVth seam of Jitpur colliery. The study was conducted to investigate the possible causes of roof cavity formation and face spalling at the middle slice face of block-3 longwall panel and to suggest remedial measures. The instrumentation and monitoring work was carried out in the panel over a period of nine months. On the basis of observations, it was found that if the maximum face span was reduced from the existing 4.8 m to 3.6 m, and if the face time schedule cycle was reduced from a maximum of 37 days to about 18 days, this problem could be eliminated. The recommendations of CMRI have been implemented in the middle slice face of block-4 panel with success. IntroductionModerate to steeply dipping, undisturbed seams of uniform thickness are worked by way of inclined slicing parallel to walls. In this method, the seams are treated as a combination of several moderately thick seams dipping parallel to roof and floor. Numerous variations of multislice mining have been used worldwide to get high coal recovery under local conditions of geology, subsidence control, proness to spontaneous combustion, statutes and economics. Multislice mining can proceed either downward descending from the roof or upward ascending from the floor. Ascending methods require backfill behind the working face to provide a base for the next slice. It is also adopted for surface protection against subsidence or mining under a massive roof. This paper presents a scientific study conducted in Jitpur colliery, IISCO where a 9 m thick seam is mined in three slices in ascending order with stowing."

Jan 1, 2002

By W. H. De Blois

Introduction In the contact process for ?the manufacture of sulphuric acid, sulphur dioxide gas - produced by the burning of sulphur or of sulphur-bearing ores, or as a by-product in the treatment of sulphide ores - is made to combine with the oxygen of the air to form sulphur trioxide, which then only requires the addition of water to form sulphuric acid. The substance, as for example platinum, causing this combination is usually referred to as a catalyst, a convenient term, in the definition and explanation of which many pages have been written. Catalysis is now a comparatively common means of effecting chemical combination, but if the question were raised here tonight as to what actually goes on when this apparently innocent third party unites the parties of the first and second . part, without itself being altered in any way, I am afraid even our most learned members would have to confess their inability to entirely explain the phenomenon; for although the subject is under investigation, there is still much to learn. The contact process, however, is one of the outstanding achievements in chemical engineering. ? From the standpoint of the difficulties involved and the time absorbed in their solution, it probably stands alone in the field of technical chemistry. In fact, the manufacture of sulphuric acid has, from the earliest days, been surrounded with problems which have interested the ablest chemists. The Chamber System Although this paper has particularly to deal with the contact process, it may not be amiss to refer briefly to the chamber system, which was, and still is, a most important factor in the sulphuric acid industry.

Jan 1, 1927

By O. Hungr, V. Gischig, G. Preisig

Deep-seated landslides are characterized by slow time-dependent movements induced by constant gravitational creep, and periods of acceleration associated with stress changes within the rock and the preexisting fracture network. Natural stress changes are typically caused by seasonal variations in surface temperatures and groundwater pressures, but also by rare and more violent events such as earthquakes. These processes are responsible for cyclic loading and unloading that leads to rock mass damage, fatigue and progressive failure with time, and may explain sudden, unexpected rock slope acceleration phases. In this work, we present a set of distinct-element models to investigate and compare the role of hydromechanical fatigue and seismic fatigue in the history of a deep-seated landslide. Hydromechanical fatigue arises from the fluctuation of pore pressure in fractures accompanying periods of significant groundwater recharge. In alpine areas, there are usually one or two cycles per year associated with snow melt and intense rainfall periods. In the presence of a deep confined aquifer within the rock slope, the amplitude of pressure fluctuations may reach values of 0.25-0.5 MPa. Hydromechanical models considering such pressure changes are able to reproduce observed slope accelerations-decelerations phases. Substantial accelerations may occur even in the absence of a cycle of exceptional amplitude, depending on the current state of fatigue. At a given time, one or more fractures may be critically-stressed, and a small change in applied stress is enough to cause local failure and induce a crisis of enhanced slope acceleration. This is augmented if the rock slope contains planes of weakness associated with its tectonic history, glacial debuttressing, etc. The corresponding behaviour is analogous to laboratory experiments on rock and metal fatigue. Similar fatigue effects have also been proposed for repeated earthquake events in seismically active regions. Unlike hydromechanical stress changes that occur in a more localized portion of the rock slope, those induced by passing seismic waves involve the entire rock mass. Moreover, the frequency and amplitude of stress perturbations due to earthquakes are different than those induced by pore pressure variations, although both likely contribute in combination to the degradation and progressive failure of large deep-seated landslides when both are present. The results presented illustrate that: (1) assessment of slope stability near critical infrastructure (e.g., hydroelectric reservoirs) should not only consider static stability, but also failure mechanisms related to fatigue that evolve over time and may result in an apparently stable slope progressing towards a critical state due to relatively small but repetitive stress changes; and that (2) characterization of fatigue processes affecting a deep-seated landslide requires multiparametric continuous monitoring at different observation points.

Jan 1, 2015

By Robert P. Dufresne

Electrolytic cells are used in electrowinning (EW) and electrorefining (ER) of non-ferrous metals such as zinc and copper, and are a critical part of the purification process. The cell is a large basin and has an electrolyte or aqueous solution, an anode and a cathode, an insulator, and incoming high amperage. Cells are exposed to unfavourable internal and external factors that have a direct impact on their lifespan. Their deterioration can be caused by incorrect polarity, insufficient magnitude, their construction, tension stress, thermal shock, corrosion and other, and their maintenance and replacement can be time-consuming, costly, difficult and environmentally unsafe. Occupational health hazards and dangers posed by the maintenance and removal of the cell should also be taken into consideration. Modifying the design and fabrication method of the cell, using chemical-resistant reinforcement, and increasing tensile and mechanical strength will defer maintenance for a very long time. This can be achieved by a double hull system that comprises full-length composite reinforcement, polymer concrete reinforced with fiberglass pultruded rods and rebars, fiberglass structural layers, and special resin matrices. This will provide protection against thermal shocks, corrosion, leakage, cracks. The design of this cell incorporates a lifting system that will afford quick and easy install without having to move a great number of cells in close proximity, since it is strong enough to stand on its own and not have to be bonded to adjacent cells. As well, the cell can be anchored with ease as it remains stable. This is especially important because space is limited to lift and manoeuver between the cell and the double-girder overhead travelling cranes. The lifting system can also prevent electrocution and loss in product quality, while increasing efficiency and safety in the workplace. Considerable savings in terms of production downtime are also part of the equation. INTRODUCTION Maintenance and replacement of electrolytic cells in electrowinning and electrorefining are operations that pose many challenges, health and safety concerns, and give rise to substantial operational costs. These problems have existed since time immemorial. Electrolytic cells are made of conventional concrete or polymer concrete, and because of the very nature of their composition and their exposure to severe and environmental conditions, their lifespan is short. Although polymer concrete is composed of high-quality materials, and has good thermal stability and resistance to chemicals, nonetheless, maintenance is frequently required in order to maintain the integrity of the cell and to ensure the quality of refined metals. Repairing concrete is a non-permanent solution as cracks will reappear, and every repair weakens the integrity of the cell a bit more, until it reaches a knock- down point and the structure is compromised. The cell needs to be replaced, otherwise the cell will collapse.

Jan 1, 2019

By Oliver Hall

WITH the friendly consent both of the Institution of Mining and Metallurgy, for whom this paper was written, and of the author, we had the pleasure of publishing Mr. Oliver Hall's paper on Mining at Noranda in our issue of last March and of having Mr. Hall present it at the Montreal Meeting. In the following pages we now report the discussion elicited by the paper at a meeting of the Institution in London on March 18th. The report is taken from the April, 1937, issue of the Bulletin of the Institution, to whom we again tender our thanks. THE PRESIDENT (MR. ROBERT ANNAN) said that this paper was, by arrangement with the Institution and the author, also being published by the Canadian Institute of Mining and Metallurgy for approximately simultaneous discussion. He was sorry that Mr. Oliver Hall could not be present to introduce it in person, for he was sure that the author would have had many more details to give about this most interesting mine. The paper contained a very useful account of mining operations, and personally he had been pleased to see the tri-dimensional projections of the orebody in Figs. 3 and S. It was a good illustration o the value of that method in presenting the form of an orebody such as this. While he had no desire to go into technical details, he wished to call attention to a remark in Mr. Hall's introduction, in dealing with the history of the mine and the principles on which it was run. The author had given an account of the early difficulties in solving geological problems, and later of the economic difficulties of seeing this mine through a period of intense depression in metal prices. He stated that it was clear that, to maintain income, tonnage must be increased, and, to maintain profits, costs must be decreased. It would be observed that there was no question of increasing the grade of ore. Then the author went on to say: 'Having set the house in order in the years of adversity, the higher price for gold is being used to mine to still lower limits and lengthen the life of the enterprise and the welfare of those dependent on it'.

Jan 1, 1937

By E. Tulcanaza

Mining companies normally establish exploration and research programs originated with actions in embryonic stage. At their early stages of development, these exploration and technological activities are subject to uncertainties that need, first, to be resolved, deciphered or, at least, mitigated for information reporting; and later, for valuation reporting. Under these circumstances, these exploration activities follow a sequence of development phases that range from exploration work to the profile, conceptual, and finally to basic engineering phases and construction. For information reporting, the International Template for Reporting of Exploration Results, Mineral Resources and Mineral Reserves integrates the minimum standards being adopted by the relevant professional bodies in Australia, Canada, South Africa, Chile, USA, UK, Ireland, and other European countries which set up the Committee for Mineral Reserves International Reporting Standards (CRIRSCO, www.crirsco.com). These standards are based on the progressive collection of relevant information to reduce present and future uncertainties over time under a context of transparency, materiality, and technical competence. For valuation reporting several procedures have been disclosed and applied. However, in the last decades financial instruments such as real options, decision analysis, and games theory have developed into a niche of great potential for mine valuation applications. The objective of this paper is to provide a summary of the information reporting standards prepared by the Chilean National Commission for the Qualification of Competent Persons in Mineral Resources and Mineral Reserves and show a procedure and an application of real options to the valuation of the sequential development phases of a mine asset from the exploration stage through up to full development.

Jan 1, 2007

By Nathaniel S. Scott

Caland Ore Company Limited, a subsidiary of Inland Steel Company of Chicago, Illinois, leased an iron ore deposit from Steep Rock Iron Mines Limited on January 1, 1953.. This deposit lay underneath a lake and was covered with 161,000,000 cubic yards of Jake bottom material, mainly silt. Removal of this material was done on a contract dredging basis. This contract was divided into a plant phase and an operating phase. The plant phase consisted of supplying two cutter-type suction dredges, each with two booster pumps in the discharge lines. All six pumps were centrifugal, had 36" discharges and were powered by 10,000 horsepower electric motors. Peak demand was 59,157 kilowatts. One hundred and forty miles of steel tower line were built to bring power to the site. The balance of the plant consisted of tugs, 12 miles of discharge line, varying from 36" diameter to 42" diameter and attendant land-based equipment. A number of interesting dams were constructed

Jan 1, 1961

By C. Barlow

The White Mesa Mill (WMM) began operating in 1980 as a regional processing mill owned by Energy Fuels Nuclear, Inc. Original mill design was for 656,000 Mtpa of U ore producing 1,250 tpa of U3O8 concentrate. Sustained market downturns delayed facility upgrades during most of the 1980s and 1990s. The new owners of WMM, Denison Mines, elected to advance the regional mill concept in 2007 with the modernization of these facilities. This paper details decisions taken and lessons learned in plant redesign, choice of leading-edge instrumentation, motor controls and process automation, training and some example benefits from process control stabilization.

Aug 1, 2010

By Donald F. MacDonald

THE cement plant nearest to Nova Scotia is not far from Montreal. Cement is a heavy product which, because of its relatively low value, cannot stand a high freight charge without unduly enhancing its cost. This is one reason why cement costs are high in Nova Scotia. The regular retail price per bag (8772 lb.) in Antigonish is 85 cents, which would be $3.40 per Canadian barrel of 350 pounds, or $3.65 per American barrel of 376 pounds.It is said that the lowest wholesale price in Halifax is 65 cents per sack, which would be $2.60 per Canadian barrel or about $2.80 per American barrel. According to U.S. Bureau of Mines statistics, the average factory price for cement in 1937 was $1.48 per American barrel, which is practically the same as the value per barrel indicated in Dominion statistics for the Canadian output during that year. The difference between $3.40 and $1.48 is $1.92. It is evident that the average user of cement in the Mari-times pays a stiff premium because Maritime cement raw materials have not been developed. Rock-wool, the manufacture of which is rapidly increasing in Ontario and the United States, is much needed for building insulation in the cold climate of Nova Scotia.

Jan 1, 1939

By A. C. Stevenson

"There are many critical application issues that affect all AC drives, but there are several that are absolutely mandatory for pulse width modulated (PWM) AC drives. If these rules are not followed, the drive system will have insulation, bearing EMI or noise problems. Pulse Width Output VoltageFigure 1 shows the output current of a typical pulse width modulated (PWM) drive. This is, of course, not a clean sine wave thus will have a lot of very significant harmonics. In fact, the harmonic spectrum is directly related to multiples of the carrier switching frequency plus side bands related to the basic output frequency. A typical spectrum for a PWM source bridge switching at 5 kHz is shown in Figure 2. Notice that the spectrum has multiples of the 5 kHz switching frequency and the number of side bands gets larger as the harmonic number increases.IGBT Switching TransientsWhenever we have PWM inverter switching, voltage transients are formed that propagate (usually at about half the speed of light) down the power cables to the motor just like in a radio frequency transmission line. If we do not terminate these transmission lines (motor cables) properly, the voltage pulses will be reflected when they reach the motor end and will be transiently increased up to twice their original amplitude.This transient voltage rise, shown in Figure 3, is important for three reasons:1. Insulation Voltage Stress — Higher voltage stress in the motor connecting cables and motor insulation will lead to a shorter insulation lifetime. If any of the voltage transient peaks exceed the insulation corona discharge level (partial discharge level), the insulation will gradually degrade with each voltage pulse. When it has been sufficiently degraded, it will then fail.Most new “inverter rated” motors have triple layer insulation which has a 1600 to 2000 volt partial discharge level. This will make them suitable to withstand the double voltage peak transient from a 600 volt inverter. It is wise to make sure of this fact, since a “standard” induction motor will only withstand about 1200 volts. Use of a standard motor in this application would shorten its life drastically. This can sometimes be as little as a matter of hours."

Jan 1, 2000

By Larry A. Morris

The environmental impacts of industrial activities have become very serious concerns of the public over the past few decades. Not surprisingly, governments have responded with legislation and regulations to force industry to operate in a more environmentally responsible manner and, more recently, have prompted industry to initiate voluntary measures in response to specific environmental issues. The concept of Product Stewardship has evolved as a system or vehicle for the industrial sector to demonstrate an active concern about the environmental impact of their products, services and processes.

Jan 1, 1996

By Larry A. Morris

The environmental impacts of industrial activities have become very serious concerns of the public over the past few decades. Not surprisingly, governments have responded with legislation and regulations to force industry to operate in a more environmentally responsible manner and, more recently, have prompted industry to initiate voluntary measures in response to specific environmental issues. The concept of Product Stewardship has evolved as a system or vehicle for the industrial sector to demonstrate an active concern about the environmental impact of their products, services and processes.

Jan 1, 1996

By M. A. Bérubé

Le but principal de cette étude était de vérifier certaines hypothèses de nature minéralogique susceptibles d'expliquer en tout ou en partie les variations importantes observées au concentrateur no 1 de Mines Gaspé quant aux performances du circuit B de broyage et de flottation. A cette fin, nous avons examiné six séries d'échantillons prélevés lors d'une campagne de mesures effectuée au cours de l'été 1980. Ainsi, la capacité du circuit de broyage semble dépendre principalement devariation s dans les caractéristiques minéralogiqu es et texturales du minerai, par exemple du rapport grenat/quartz, le grenat ayant une influence néfaste sur le rendement de cette étape, contrairement au quartz . Quant au processus de concentration, la fraction du cuivre sous f orme de minéraux difficilement récupérés par flottation, en particulier des carbonates de cuivre, varie de façon significative dans le minerai, et cela peut certes expliquer en partie des récupérations parfois plus basses. Malgré ces variations important es de la composition minéralogique globale du minerai et de sa broyabilité, le degréde libération des sulfures de cuivre dans le produit de broyage dépend presque seulement de la granulométrie de ce produit. Afin de garantir des performances égales à l'étape de concentration, il est fortement suggéré de contrôler cette granulométrie à un niveau constant.

Jan 1, 1984

By A. Zrimsek, G. Vingas, R. Wolke

IN 1952, prompted by the great demand of the Canadian drilling and foundry industries for sodium bentonite, the Geological Department of Magnet Cove Barium Corporation, Limited began an extensive search for bentonite deposits throughout western Canada. Their efforts were rewarded in 1958, when substantial deposits of high quality material were found approximately 100 miles southeast of Edmonton, Alberta. The bentonite material, a part of the Edmonton formation in the Upper Cretaceous, is located approximately nine miles south of the town of Rosalind. The land where the bentonite lies has in places .been eroded by stream and glacial action to form a wide gully, convenient for strip mining methods (see Figure 1). The bentonite bed is almost flat-lying, dipping to the southwest at approximately 12 feet per mile. The main bed is 8 to. 10 feet thick and is covered with 15 to 25 feet of overburden. Before stripping, the area is drilled and sampled to evaluate the quantity and quality of the bentonite.

Jan 1, 1962

By Y. M. Shneerson, E. E. Zhmarin, E. M. Vigdorchik

One of the Gipronickel Institute activities is research and development of customized leaching technologies. The work is performed in several steps. Leaching kinetics are studied on a lab-scale according to a special procedure. Experimental data are processed using mathematical models of batch and continuous processes. Reliability of kinetic data and preliminary calculations is verified experimentally in laboratory reactors of various capacities. If necessary, certain parameters of the mathematical model are adjusted after pilot plant tests in continuous mode ( 4-reactor train, each with 25 L capacity). The specified kinetic characteristics along with the mathematical model are used for further development of industrial leaching technology.

Jan 1, 2005

By M. M. C Jiménez, J. A. S Ténorio

For the recovery of valuable materials and for the protection of environment, recycling process of printed circuit board is an important subject of study. Moreover, the popularization of the computers and its technological evolution has generated a large number of waste electrical and electronic equipment. This paper presents a study of synergistic solvent extraction of copper, nickel and zinc from a sulfuric leaching liquor of printed circuit boards (PCB’s). The percent extraction of copper, nickel and zinc from dilute aqueous sulfate media besides synergistic effect of mixture of the .extractants Cyanex 272 and D2EHPA have been studied. Furthermore, different conditions such as temperature, pH of the feed solution have been examined. The results suggest that the synergistic effect of the .extractants mixture enhance the extraction efficiency of nickel.

Jan 1, 2014