Search Documents

By S. Markstrom

The Boliden AITIK copper mine is located 100 kilometres north of the Arctic Circle in northern Sweden. A pre-feasibility study was conducted in 2005 with the aim of increasing the capacity of the existing processing plant. After analysis, options to upgrade the existing plant were abandoned in favour of building a new processing plant, with higher capacity and therefore greater profitability. A new plant could be designed with greater flexibility to make potential future expansions easier. A feasibility study for a new 36 Mt/y processing plant including fully AG grinding circuits and flotation was completed in 2006. The project was approved by the Boliden board shortly thereafter. Construction started in the beginning of 2007 and was completed during 2009. Commissioning of the new plant was undertaken in the first half of 2010. The grinding circuit consists of two lines with each line consisting of a 22.5 MW AG mill and a 10 MW Pebble mill in closed circuit with a spiral classifier. The nominal production level is 2 200 t/h for each grinding line. This paper presents the start-up and operation of the grinding circuit.

Jan 1, 2012

By E. J. Schwarz, A. A. Winir

"Absolute magnetite contents were determined for asbestos specimens in various stages of milling by using a Faraday-type thermomagnetic balance. Comparison of these results with magnetic ratings (MR) supplied by the mining companies cooperating in this study reveals strong scatter. The main cause of this scatter is thought to be that the MR values were obtained in magnetic fields well below the saturating field of magnetite (5,000 oe). However, only the saturation moment is an intrinsic property and consequently must be used for the purpose of obtaining reliable estimates of the magnetite content. Curie points indicate that virtually pure magnetite and possibly Ni3Fe is present in all samples, and another phase, probably (Cr, Al) magnetite, is present in a few samples. The susceptibility in fields stronger than 5,000 oe is positive and falls in the normal paramagnetic range, whereas sy nthetic chrysotile exhibits weak diamagnetism. This suggests that, as a general rule, the least adulterated natural chrysotile concurs with the samples showing the smallest positive susceptibility above 5,000 oe. The magnetite appears to increase in quantity with a decrease in fibre length and to be somewhat more uniform in distribution for samples showing substantial fiberization (opening of the fibres)."

Jan 1, 1971

A direct comparison has been undertaken between laboratory wind tunnel experimentation and computational fluid dynamics simulation of a 3D manufactured analogue for a body of fractured broken rock, created with CAD/CAM techniques. Detailed descriptions of the ?design? of the analogue (using a discrete element analysis multi-body simulator), its manufacture (using computer aided design and 3D printing technology) and the laboratory experimentation (inserting the physical analogue into a laboratory scale wind tunnel) are presented. The agreement of the results of direct experimental observations on the manufactured analogue with the values from CFD simulations of those experiments justifies the utilization of a CFD environment for the practical investigation of geometric factors controlling air flow and heat exchange in complex assemblages of broken rock blocks. The ultimate goal is described, that of developing functional relations between bulk properties of such assemblages (such as their porosity and bulk density) and the low-level geometric factors that dictate the air flow behaviour, such as the equivalent perimeter length of the cross-sectional area available for flow, or average flow path tortuosity. A practical application area of the work in the mining context is also described; equivalent continuum air flow and heat transfer constitutive models developed on the CFD tool from such functional relations are useful in characterization of seasonal heat storage in large scale bodies (approximately 1 km3) of broken rock.

Aug 1, 2013

By J. S. Fox

"Pyroclastic rocks are useful guides to volcanic centers due to the tendency of their fragments to increase in size and volume toward the source vent. The felsic rocks of these centers can be the prime hosts of base metal deposits in the Precambrian Shield; their sub-volcanic equivalents are often the focus of porphyry copper mineralization in the Cordillera. Quantitative mapping of pyroclastic rocks has not yet developed into a routine prospecting tool in Canada, however, possibly due to the cumbersome nature of existing manual techniques and their limitation to structurally simple terrains.A rapid pyroclastic mapping method has been developed whereby the field geologist acquires only a down-plunge outcrop photograph, a record of the fragmental deformation ellipsoid and a record of some descriptive features from each station. Mean fragment size and volume percent are obtained later in the laboratory from a photo-enlargement: by means of a digital analyzer. A computer program uses the strain parameters to 'undeform' the field measurements and obtains genetic information from the descriptive data. Results can be superimposed on a geologic map, with values for each station being represented by a dot of a specified diameter corresponding to the size or volume percentile range to which the value belongs.Control traverses were run over the pyroclastic rocks surrounding the Anderson Lake mine and the Flin Flon South main shaft in northern Manitoba. In both locations, the mapping has delineated regular increasing trends in mean size and volume per cent toward the head frame."

Jan 1, 1977

By L. L. Bolton

The Department of Mines as at present constituted has evolved from the organization which came into existence following the passage of the Geology and Mines Act by the Dominion Parliament in 1907. At the outset, it may be said that it is not a function of the Department of Mines, nor of any of its branches, to administer the mining rights vested in the Crown. The title to Crown lands in the provinces of Nova Scotia, Prince Edward Island, New Brunswick, Quebec, Ontario, and British Columbia ( with the exception of certain specified areas, such as Indian Reserves, Ordnance Lands, the Railway Belt of British Columbia, and the Peace River Black) is vested in the respective provincial governments ; the title to Crown Lands in the provinces of Manitoba, Saskatchewan, and Alberta, the Yukon and Northwest Territories, and in the Canadian Arctic, is vested in the Dominion Government, and matters pertaining thereto are (with a few exceptions) administered by the Department of the Interior, Ottawa. Nor are statistics of mineral production at present collected and published by the Department of Mines. This function did belong to the Geological Survey from 1886 to 1906, and to the Mines Branch from 1907 to 1920; but commencing with 192l this duty was transferred to the Dominion Bureau of Statistics, consequent upon the decision of Government to place the collection of all statistics under the direction of one officer.

Jan 1, 1929

By J. L. Chakravarty, S. K. Dutta, S. Banerjee, D. Putatunda

"General purpose uniprocessor systems used in control applications, however fast they may be, at a certain stage attain saturation, forcing the user or designer to consider other avenues for solving the problem. This paper gives a broad overview of multiprocessing with special reference to transputers. Virtually all aspects, from parallel systems real-time control to artificial intelligence (AI) and expert systems, have been highlighted. The application of transpurters in unilayer and multilayer control are discussed in detail, with specific attention to sensor integration. Two case studies describe at length the utilization of transputers. IntroductionIn conformance with the high level taxonomy of parallel computer architectures as given by Ralph Duncan(l) (an improvement to Flynn's classification, which maintains the essential elements of useful taxonomy based on instructions and data streams), the MlMD architectures are categorized into two groups: (I) shared memory, and (2) distributed memory type. While the shared memory multiprocessors are more popular than the message-passing multiprocessors because they can be programmed in a conventional sequential fashion, their aspect of the architecture creates a perfonnance bottleneck. In contrast, message-passing multiprocessors (MPM) suffer from no such limitation and can attain linear speed increases that are directly proportional to the number of processors put into use. The MPM implementation also has its own advantages and disadvantages. Because the performance of the system is heavily dependent on it, the interconnection strategy in a distributed memory MIMD machine is of paramount importance. The transputer(2.J), a multiprocessor node of the distributed memory type, is becoming very popular. The advantages offered by the transputer make its application in the mining and processing industries very promising."

Jan 1, 1994

By L. McFarlane, D. Rollwagen

"Madawaska Mines produces a uranium precipitate (83-85% u3o8) using a magnesium oxide slurry to precipitate the uranium from solution. The solution, at approximately 9""0 g/l u3o8 is neutralized to a pH of 7.0. At the Eldorado Nuclear Refinery in Port Hope, the precipitate is not acceptable as a single feed to the refinery process. It was discovered that a 2% silica impurity caused emulsion problems in the solvent extraction column.After extensive studies of possible solutions, such as two-stage precipitation and solvent extraction, an acceptable solution was found. The selective precipitation of uranium at a pH of 3.5-4.0 using Hydrogen Peroxide produces an almost silica free product of higher purity (90-93% u3o8) to that of straight magnesium oxide precipitation. Introduction Madawaska Mines Limited is located four miles southwest of Bancroft, Ontario. The annual production of u3o8 is approximately 610,000 pounds. To produce the final product or yellowcake, nine separate steps are required. These are (1) grinding, (2) dewatering, (3) leaching, (4) acid filtration, (5) clarification, (6) ion exchange, (7) precipitation, (8) washing, and (9) drying and packaging. To illustrate these steps, a complete flowsheet of the mill is displayed on page three.The yellowcake is sent to Eldorado Nuclear Limited in Port Hope, Ontario for further concentrating and refining. As part of their routine specification check, a test called the amenability test is performed. This test indicates how a particular dissolved yellowcake product reacts to solvent extraction. The Madawaska yellowcake did not pass the test."

Jan 1, 1982

By Norman Orr, J. W. Gregg, Jack Wahl

The Pembina Cardium pool is a low permeability, stratified, solution-gas drive reservoir. Water-flooding has proven to be an effective means of pressure maintenance for all areas of the pool in which an economic rate of water injection can be maintained. The majority of water injection wells in the pool are converted oil well~ with capacities greater than 100 millidarcy-feet. If the average injection rate per unit of capacity can be in-creased the lower capacity areas of the pool can be economically flooded. Theory, laboratory work, and two . early miscible-flooding projects with-in the pool suggested that average water injection rates for converted wells could be increased two to three-fold by the initial injection of natural gas liquids and natural gas. How-ever, these two early projects received volumes of natural gas liquid!:' and high-pressure natural gas which would be economically prohibitive for routine stimulation. Area D, one of the Five-

Jan 1, 1962

By Gaston Giuliani, Jérome Massot, Didier Bourlès, Lionel Siame

"Abstract - We present a new approach for the evaluation of the potential of emerald reserves in gem projects using beryllium (Be) mobility. The distribution of Be in the different phases of hydrothermally altered (albitized) black shale hosting Colombian emerald deposits indicates that Be mobility is associated with the breakdown of Fe-Mn oxyhydroxide phases. The amount of Be that can be mobilized (~0.7 x 10-6 g/g; i.e., 0.7 ppm) may represent up to 18 wt% of the total Be contained in the black shale. A mass balance calculation applied to a well-constrained alteration zone of the Chivor mines, and based on the quantification of Be that can be mobilized under hydrothermal conditions, gives an estimate of the total gem reserves of these mines. Resumé - Une nouvelle approche, basée sur la mobilité du béryllium (Be) pour l’évaluation des réserves d’émeraude dans des projets d’exploitation de gemmes est présentée. La distribution du Be dans les différentes phases minérales de schistes noirs hydrothermalisés (albitisés) qui contiennent les gisements d’émeraude colombiens, indique que le Be mobilisable se trouve dans les oxyhydroxydes de fer et de manganèse. La quantité de Be potentiellement mobilisable (~0,7 x 10-6 g/g; soit 0,7 ppm) constitue jusqu’à 18% poids du Be global contenu dans le schiste noir. Un bilan de masse appliqué à la zone d’altération hydrothermale des mines de Chivor et basé sur la quantification du Be mobilisable, donne une première estimation des réserves à émeraude de ces mines. rieur."

Jan 1, 1999

By C. D. M. Chisholm

IN discussing stope filling, or backfilling, at the Sullivan mine, at Kimberley, B.C., a brief description of the problem will first be presented. The Sullivan orebody is a replacement in quartzite, with the ore con-forming, for the most part, with the bedding. The dip of the vein, apart from local irregularities, averages about 15 degrees near the outcrop in the southwest section of the mine, and steepens to almost 40 degrees at the northeast end of the mine. The thickness varies from a few feet to over 200 feet at the widest sections. The mineable length along the strike has averaged about 4,000 feet between the 4,600 and 3,900 levels-the section under discussion in this paper. To date, 28,000,000 tons of ore have been mined by the room-and-pillar method. Prior to 1930, all ground opened up had been supported by ore pillars, left during mining operations. From that time, the recovery of the ore from these pillars has been given serious consideration. Backfilling, as being carried on today, is the result of this study and is being done for two reasons: (1) to allow extraction of the ore pillars, and (2) to minimize subsidence of the hanging-wall rock, except where forced caving is found desirable. PRELIMINARY DEVELOPMENTS LEADING TO BACKFILLING When the Sullivan orebody was first opened up, early in the century, there appeared to be low-grade sections of the vein sufficient in extent to serve as permanent support for the roof. However, as mining extended into sections of the vein that showed continuous ore over greater areas, wooden cribs, filled with waste and low-grade ore, were erected. In some stopes, these cribs were as large as 40 ft. by 100 ft. in plan and from 50 ft. to 60 ft. in height, but it was soon realized that this method of support was inadequate. As mining progressed, it was found necessary to leave ore pillars, which eventually became the sole system of support. At first, these pillars were left at irregular intervals, but later they were laid out at definite locations on the mine plans, and these locations were adhered to as closely as mining would permit.

Jan 1, 1941

Mercapto organic compound SDMP was used as a depressant for separation of copper activated marmatite from pyrrhotite in the presence of butyl xanthate. Flotation results show that SDMP has strong depressing effect on pyrrhotite recovery in the absence and presence of copper ion, but has promotional effect on marmatite recovery when added together with copper ion. The flotation test of mineral mixtures shows that copper-activated marmatite could be separated efficiently from pyrrhotite using SDMP as depressant. Infrared adsorption spectra demonstrate that SDMP has a strong adsorption on pyrrhotite surface through its functional groups such as ?SH, -S03.

Jan 1, 2006

By A. J. Brown

This paper presents an economic evaluation of resin ion exchange and solvent extraction for the purification and concentration of uraniferous solutions derived from sulphuric acid leaching operations. Capital and operating costs are related to the uranium tenors of pregnant solutions. The conclusions drawn herein apply only to cases where resin and liquid ion exchange are technically feasible process alternatives. It is shown that solvent extraction is economically favoured for pregnant solutions at tenors greater than 0.90 gpl U3O8. Pregnant solutions with tenors below 0.35 gpl U3O8 are best treated by resin ion exchange. Between these concentrations, the economics are marginal and the favoured process is indistinguishable within the limits of accuracy of this study.

Jan 1, 1979

By L Tafaghodi Khajavi, M. Barati

The distribution of phosphorus between solid silicon and iron-silicon melt was determined to investigate the degree of phosphorus removal from silicon by solvent refining with iron-silicon alloys. The distribution coefficient which is the ratio of the mole fraction of phosphorus in solid to that of liquid is as follows: 0.22±0.02 (1310°C), 0.29±0.02 (1260°C) and 0.33±0.02 (1210°C). The removal percentage of phosphorus is: 84.2% (1310°C), 72.5% (1260°C), and 63.7% (1210°C). The average phosphorus content of produced silicon in the proposed solvent refining process would be over two times less than that of the conventional directional solidification. The values of interaction coefficient of phosphorus on iron at different temperatures were obtained as -3460±155 (1310°C), -3595±159 (1260°C) and -3694±119 (1210°C). Self interaction parameter of phosphorus at different temperatures are as follows: 68±4 (1310 ?C), 78±10 (1260 ?C) and 103±19 (1210 ?C). The calculated values for distribution coefficient of phosphorus at infinite dilution are: 0.22±0.00 (1310°C), 0.30±0.00 (1260°C) and 0.34±0.00 (1210 °C).

Jan 1, 2015

By Georges Croisé, Les-Lee Thompson, Adrien Debergé

Membrane filtration systems have regained focus in recent years as an effective means of liquid-liquid separation to increase the concentration of valuable elements, recover reagents or remove impurities. ORANO Mining (formerly AREVA) investigated this cost optimization process opportunity as early as 2011 for implementation at the Trekkopje project (Namibia). The key focus was to separate and recycle bicarbonate from the uranium bearing eluate solution. The performance targets were successfully achieved at lab- and pilot scale with an ultrafiltration and nano-filtration configuration system. Early 2015, ORANO Mining further launched an investigation into the use of membranes for acid recycling at the KATCO In Situ recovery mine in Kazakhstan based on the favorable results from the original bicarbonate application. KATCO is the world leader in ISR uranium mining with an eluate processing capacity of 80 000 m3/yr. This site consists of two processing plants namely, Muyumkum and Tortkuduk, located 40 kilometers apart, both operating under acidic conditions whereas precipitation and packaging are based in Tortkuduk only. This paper serves to present the results from the integration of a nano-filtration system at the Muyumkum satellite processing plant. The project consisted of screening laboratory bench studies conducted at ORANO-CIME followed by process validation at KATCO through further bench and pilot test work. The feasibility study assessments were successfully concluded which led to the implementation at an industrial scale in Muyumkum of a nano-filtration process to reduce eluate volumes being sent to the uranium precipitation section whilst achieving effective separation of uranium from sulfuric acid. Nano-filtration technology has drawn significant attention due to the efficiency and reproducibility of the process and its moderate capital cost relative to operational savings. The reliability of the previous results is a great opportunity to reduce operative expenditures within ORANO’s next ISR mining project in Mongolia.

Jan 1, 2020

By Samuel B. Rombeger

The behavior of gold in hydrothermal systems is evaluated as a function of pH and oxygen and sulphur activities at temperatures to 250°C. Under conditions of stability of pyrite and argillic alteration as emblages, gold will be transported as bisulphide complexes. In systems containing significant amounts of arsenic, thioarsenide complexes may be important. Oxidation, dilution and reduction in sulphur activity would cause gold deposition from saturated solutions under these conditions. Gold chloride complexes will predominate under oxidized conditions where hematite or other oxides are stable and depo ition would result from increase in pH and/or reduction . Absorption and coprecipitation are po sible mechanisms of deposition for gold in certain low grade depo it . Low concentrations of gold in the transporting solution combined with the ignificant solubility of gold as bisulphide complexes, sugge t hydrothermal solutions rarely may be saturated with gold and coprecipitation with sulphides may be an important initial depositional process. Recrystallization of the sulphides in the presence of the hydrothermal solution would be re ponsible for release of gold to more table ite . Thi mechani m i supported by the close association of gold with pyrite in many hydrothermal gold deposits.

Jan 1, 1986

By W. Beres, M. Bielawski

Recent research on the development of erosion resistant coatings has been directed to the finite element modelling of the behavior of coating and substrate, and their interface under the impact of eroding particles. The approach presented in this paper is based on advanced computer simulation techniques using ABAQUS/Explicit to investigate stress and strain at the surface and at the coating/substrate interface of multilayer coatings under single particle impact. It was found previously that solid particle erosion mechanisms are predominantly governed by the kinetic energy of the impacting particles. However, recent modelling efforts revealed that effects of various material models could be also significant. Therefore, different material models representing relevant coating and substrate properties were investigated and the effects of these models on the coating/substrate response were studied. Particularly, differences between elastic, elastic-plastic and brittle cracking model responses were assessed.

Jan 1, 2006

By S. Kaiman

This paper describes flotation test work conducted over the past several years at the Mines Branch, Ottawa, on the radioactive quartz-pebble conglomerate ores of the Elliot Lake area of Ontario. The purpose of this work has been to produce a uranium flotation concentrate for sub-sequent leaching operations. The results of earlier investigations are summarized and correlated with the results of mineralogical studies of the ores and flotation products. The results of recent pilot-plant investigations by flotation, as well as by gravity concentration followed by flotation of the gravity tailings, are given. The principal collector used for uranium flotation was a tall oil fatty acid, and the indicated total cost of all reagents ranged from 21 to 31 cents per ton of ore treated.

Jan 1, 1966

"Syncrude Canada Ltd. operates one of the largest surface mines in the world. The mining operation has two distinct phases: (1) the removal of the overburden, utilizing trucks and shovels; and (2) the mining of oilsand with drag lines and bucketwheels. Both phases combined move approximately 330 000 BCM per day.In support of current production demands and to provide a contingent oi/sand source, Syncrude has developed an Auxiliary Production System (APS) supported by the truck and shovel operation. This system utilizes oilsand sources within the existing mine area on an as-needed basis.The recent increased capabilities of the processing plant to handle a larger volume of oilsand has increased the reliance of the APS system. To facilitate the increased capacity, an auxiliary mine was developed external to the Base Mine operation with a production capacity of4.7 MBCM of oilsand per year.Development of the Northwest Auxiliary Pit began in January 1990, with the first cubic metre of oilsand taken to the plant in June, 1990. The Auxiliary Pit, as designed, has a total ore reserve of 68 MBCM of oi/sand."

Jan 1, 1993

By H. M. Woodrooffe

This paper deals with the laboratory facilities at the Mines Branch for carrying out research in the industrial minerals field, and also reviews current programs in ceramics and construction materials, in non-metallic minerals and in the milling of industrial minerals. It then discusses the application of these pro-grams to industrial problems.

Jan 1, 1967

By H. McIntire, R. Preston, D. Roberts

"Repeated 3D terrestrial digital photogrammetric surveys were conducted on hard rock mine pillars to characterize damage during secondary mining. Damage was quantified by measuring Depth of Failure, DOF, from spalling material and crack intensity, D21. These damage values were then correlated to visually assessed Pillar Damage Ratings and numerically estimated pillar loads. Measured damage, particularly Depth of Failure, correlated well with Pillar Damage Ratings. Numerical predicted pillar stress vs. damage exhibited the expected trend with shorter pillars being stronger. High resolution photographs and 3D models were also used to characterize damage mechanisms, which were found to be structurally constrained. INTRODUCTIONThe Doe Run companies Southeast Missouri Operations consists of six room and pillar lead mines (Brushy Creek, No. 29, Casteel, Buick, Fletcher and, Sweetwater) (The Doe Run Company, 2014). The mines are hosted in the Carbonates and Shales of the Viburnum trend with mining depths varying from 180 to 300 m. Pillars are commonly cut square with widths varying from 7 to 9 m and heights generally between 5 and 18 m, resulting in extraction ratios between 80 and 85% (Roberts et al., 1999). Figure 1 presents an idealized stratigraphic section through the Viburnum trend and Figure 2 shows a plan view of the five areas spanning the three mines included in this study."

Jan 1, 2015