Search Documents

By N. N. Rulyov

"Starting from fundamental principles of colloid-hydrodynamic theory of disperse systems we have shown that application of strongly non-uniform hydrodynamic fields allows to achieve not only faster rates of flocculation of suspension, but also supports significant improvements in the quality of clarified water and separation characteristics of solid phase. Specifically, it has been experimentally proven that the new treatment method based on these principles (then termed as ""ultra-flocculation"") allows:•,Increase the output of thickeners and pressure filters by 1,5-1,7 times;•,Decrease solids fall through into the filtrate in the process of vacuum filtration by 2¬3,5 times;•,Improve the rate of purification of water phase in the upright thickener by 1,5-1,9 times;•,Decrease flocculant consumption by 1,5-3 times;•,Increase the effective operational life time of cloth filters by 3-4 times;•,Ensure sustainable operation of separation equipment, i.e. decrease the sensitivity of process to variation in suspension concentration, as well as to variations of suspension composition and dispersion characteristics;•,Apply flocculant solutions of concentration 2-3 times higher, thus increasing the capacity of equipment used for solutions preparation."

Jan 1, 2004

By X. T. Feng, Y. H. Hatzor, Y. Tal, G. Yagoda-Biran

"When studying jointed rock mass deformation around underground openings it is of great importance to model correctly the excavation sequence during the numerical simulation. This is because for effective arching mechanism to develop in the roof minute block displacements must take place and some of the available discontinuities shear strength must be mobilized. If from the beginning of the simulation the underground opening already exists in the numerical model, block displacements into the excavation space will initiate and develop from time zero, before the initial stresses in the model have attained their actual initial level in the field. These initial block displacements are therefore artificial and exist only in the numerical model, not in the physical reality, and may lead to erroneous assessment of the stability of the designed structure, typically on the conservative side. We have introduced sequence excavation capabilities both in the numerical manifold (NMM) and the discontinuous deformation analysis (DDA) methods and show here the advantages of this modification using three different case studies, each illuminating a different aspect of this enhancement.We begin with the 25 meter deep 2000 year old underground Zedekiah limestone quarry below the old city of Jerusalem, Israel, which is still standing today unsupported with a free span of 40 m. We show that when the opening exists from the beginning of the numerical simulation the required friction angle for roof stability is 25 degrees, whereas when the opening is removed after all stresses and displacements in the model have been stabilized the required friction angle for stability is only 15 degrees.We then model the excavation sequence of a tunnel model representing a 2500 meter deep research tunnel in the Jinping hydroelectric project, China, in order to determine the in situ stress field at this depth by a grid search inversion of displacement data obtained using the sliding micrometer technology in the course of tunnel excavation. Thus we are able to constrain the in situ stress field at these depths where standard in situ stress measurement procedures are extremely difficult to execute properly.Finally, we use sequence excavation modeling capability to find the total height of the expected loosening zone around tunnels excavated through columnar jointed basalts which pose a great engineering challenge because of the characteristic dense network of slender prismatic blocks that transect the opening at a steep inclination. We use MPBX data obtained during excavation of a deep tunnel through such a rock mass to validate our numerical results and show that application of standard empirical guidelines for dimensioning rock bolt reinforcement in such rock masses may in fact result in very un-conservative design because existing empirical approaches typically ignore the anisotropic nature of the structure of such rock masses which, as we show, plays a very significant role in determination of the extent, shape, and geometry of the loosening zone around the opening."

Jan 1, 2015

By G. Swan

"The selection of material comprising a backfill is, of economic necessity, site dependent. Nevertheless, given the existing range of typical components-coarse waste, alluvial sand, tailings a balanced or optimal choice is no straightforward matter. A new design approach toward deciding what constitutes an optimum combination of backfill material promises to be useful. In particular a 'binder ' number, based on the mean distance between aggregate particles, specific surface and cement content, is proposed. Using this number, related empirically to compressive strength, the expected mechanical performance of any cemented fill can be predicted.IntroductionOver the years a considerable volume of information has accumulated on mine backfill material design. The principal aggregate component has been deslimed mill tailings, though more recently admixtures of rock waste, sand and tailings are quite common. For these materials uniaxial compressive strength and percolation rate properties are known to be controlled by, among other things, aggregate grading. While empirical formulae exist for relating grading to percolation rates, considerable uncertainty exists concerning strength development."

Jan 1, 1985

By Jean-Loui Frenetie, Françoi Himbeault

"Flow of traffic in the underground mine has been improved through the years with clever use of traffic lights. The evolution is characterized by three major design changes. This paper will scan the basic criteria of these designs.IntroductionMines Gaspe, formerly known as Gaspe Copper Mines Limited, is a member of the Noranda Group of companies. The mine is the ""raison d'etre"" of the town of Murdochville, located 600 m above sea level on the Gaspe Peninsula. Paved highways link the town with Gaspe, 95 km to the east, and with Anse Pleureuse, 400 km to the north, on the Gulf of St. Lawrence.The low-grade copper mineralization was discovered in 1921 at Copper Mountain by local prospectors, the Miller brothers. Noranda Mines Limited obtained an interest in the property in 1937. World War II interrupted exploration work and it was not until 195I that a decision was made to bring the property into production.Initially, operations were confined to the Needle Mountain underground deposits which commenced production in 1955. Between 1968 and 1982, low-grade ore from the Mountain open pit supplemented the production. Due to the depressed market, surface and underground operations were suspended in 1982. Needle Mountain underground mining resumed in the second half of 1984, but the Copper Mountain open-pit operation remained idle. Since 1979, more than 75 km of exploration drilling resulted in the discovery of two new deposits, one which is located under the town of Murdochville . Mines Gaspe's present ore reserve, approximating 8 million tonnes, will be depleted by the end of 1992."

Jan 1, 1988

By A. Taylor, E. Thorn Corthay, R. Storey

In response to requests from its stakeholders, the International Standards Organisation is engaged in development of an international standard for Energy Management Systems (EnMS) which will become "ISO 50001". This new standard will build on the successes of both the EN16001 EnMS standard that has been used by dozens of European companies, as well as the ANSI/MSE 2000:2008 EnMS standard that is currently being used in several pilot projects in the USA and Ontario. This paper provides an overview of the key points of the EnMS standards, and describes how they can be used to drive sustainable energy reductions in the metallurgy industry.

Jan 1, 2010

By J. Janeson

Wall control at the Pipe Open Pit is of primary importance in ensuring the long-term stability of the operation, while keeping costs to a minimum. Blasting techniques have been adapted to the variations in competence and structure of the wall rocks. A portion of the perimeter wall is being developed in incompetent peridotite . A recent change in pit slope design provides a wide safety berm on alternate benches. A support program which consists of pinning the crests of wide berms with vertical reinforced concrete dowels and horizontal bolting of walls shows evidence of increasing the stability of the pit walls. This paper describes the blasting and support techniques which are contributing to successful wall control in the Pipe operation.

Jan 1, 1979

By N. W. D. Davis

"As I have recently carried out some further research on the Navan lead-zinc deposit data while working in Michel David's research team, I should like to add a few comments on the paper- ""Universal Kriging for Ore-Reserve Estimation- Conceptual Background and Application to the Navan Deposit"", by M. Dagbert and M. David (CIM Bulletin, pp. 80-92, February 1976). The first comment is that since this research has been carried out, important new theoretical advances have been made which make for an easier application of geostatistics to the non-stationary case (see Matheron0l). This is the theory of intrinsic random functions of order k. With the aid of this theory, it has been possible to write computer programs which can carry out automatically universal kriging, although so far such applications have been largely confined to automatic contouring and not to mining problems. However, if approached with care there is no reason why these methods should not be applied to mining problems and, in this case, an automatic study has been done on this data."

Jan 1, 1976

By L. Szecowka, M. Poskart, Siwka M. . J.

Oxides of nitrogen, created during combustion, are the most hazardous components of atmospheric pollution. However, it is possible to limit the negative influence of hazardous components on the natural environment. An experimental appartatus was built to determine the influence of the following "primary methods" on the reduction in concentration of NOx: air staging, reburning and flue gas recirculation. The influence of the simultaneous usage of the primary methods on reduction in NOx emissions was also examined. A significant increase in the efficiency of NOx reduction was achieved in two cases.

Jan 1, 2004

By W. Swidzinski

"Zelazny Most" post-flotation copper mine tailings pond is the only place to of storeing wastes for KGHM POLSKA MI EDZ S.A. The flotation tailings is are the main waste stream in copper mining in Poland. Sufficient storage capacity for tailings is crucial for , thus uninterrupted production of copper is crucially related to the possibility of storing wastes in the pond. The pond covers a Its over 14 km2 arca, almost 50 m high dams making this dame this construction one of the largest in the world. The risk assessment of potential damage due to un stable ility loss of dams or environmental contamination, as well as safely constructing damsincrease of dams within the design criteriaprocess, require quick access to a large amount of the monitoring data , which in vast amount have to be monitored, that needs to be analyzed and processed and reported, every day. This In the paper describes the numerical information system "SyZeM" , used for designated to the "Zelazny Most" pond, baseding on the Oracle database and Geographical Information System , to manage the graphical and descriptive data in coherent way., is presented. The main structure of the system, as well as the methodology of storing, processing and reporting the geological, geotechnical, hydrogeological, geophysical, chemical and survey data are shown. The aspects of Optimizing optimal and risk mitigation and safe management of copper wastes and risk mitigation with the help of "SyZeM" are discussed.

Jan 1, 2007

By H. A. ?ye

The ISO TC 226 (Materials for the production of primary aluminium) has presently issued more than one hundred standards on the materials: alumina, pitch, petroleum coke, carbon anodes, carbon cathodes, ramming paste, fluorides and refractory). The object of the standardization work is to find methods that both material producers and smelters will accept. Methods that are specific for the operational conditions have been developed in addition to more traditional room temperature methods. Examples of important properties under operational conditions are: Air and C02 reactivity of anodes, Equivalent temperature for baked anodes, Sodium expansion of cathode blocks, Shrinkage and Rammability of paste, Penetration of electrolyte into refractories.

Jan 1, 2006

By G. F. Trainor

At the Canadian Natural Resources Limited (CNRL) Horizon Mine they use Wenco International Mining Systems Ltd (Wenco) Fleet Management System to monitor and control their production fleet with the goal of increasing operator productivity and safety, and raising dispatcher awareness and control. Amongst the broad productivity goals CNRL wanted to achieve with help from the system was a very specific need to blend ore at the truck level. CNRL uses 25m x 25m block geological model information to represent their complex ore body. Wenco's High Precision GPS application, BenchManager provides precise graphical actual-vs-design operator feedback and system integration. Together the two companies advanced the BenchManager product to meet CNRL's needs by using live camera feeds to compare activity with data collection that ultimately lead to changes in the algorithm to include enhanced GPS indicators and the support of a GLONASS assisted solution generating distance and bearing information.

May 1, 2011

By S. Balideh

A good understanding of the behavior of rock helps us to make more informed decisions regarding geo-structures. Engineers need accurate equations to calculate the strength and deformation of rock before and after failure. Previous studies explain the failure of rock to ultimate strength, and laboratory tests adequately determine the ultimate strength and deformation modulus of rock. However, there are few comprehensive equations to determine the post-failure strength and deformation of rock. Previous work shows that the post-failure behavior of rock depends on the behavior of the broken rock particles after failure. The following question is then posed: How can the post-failure behavior of rock be determined by the behavior of broken rock particles? In order to answer the question, this study pursues three objectives: (i) to explain the behavior of broken rock at low confining pressure; (ii) to estimate the behavior of broken rock via the extrapolation of scaled laboratory testing; and to suggest a procedure (iii) to outline the post-failure behavior of a rock mass at low confining pressure commensurate with the behavior of broken rock in a rock mass.

Aug 1, 2013

By P. A. Bahri, D. G. Dixon, T. M. Woodward

A comprehensive mathematical model of the Sherritt-Gordon ammoniacal pressure leaching process at K winana Nickel Refinery has been constructed. The process is comprised of six autoclaves functioning as a three-stage leach circuit, operating over the temperature and pressure ranges of 85-95°C and 750-1000 kPa, respectively. The process chemistry forms a complex series-parallel reaction network, characterised by: (1) the gas-liquid mass transfer and reduction of oxygen, (2) the oxidation of eight distinct minerals, (3) the oxidation of sulphur, and successive reactions involving various intermediately oxidised sulphur species, and (4) the oxidation of Fe(II) to Fe(III), and subsequent precipitation as a hydrated ferric oxide. Material balances were developed for species in all three phases, and an energy balance to account for all reactions and phase conversions. The multiple convolution integral (MCI) statistical reactor model was employed for the scale-up of particle kinetics. The model has been validated against plant data, and simulation results are in agreement with plant performance.

Jan 1, 2005

By Denni Hoffmann

"Banded iron formation rocks associated with massive sulfide lenses in the Broken Hill Pb-Zn-Cu-Ag deposit in the Namaqualand Metamorphic Complex, South Africa, were investigated with respect to the geochemistry of manganiferous silicate-rich bands. Two common varieties of these are: amphibole- and garnet-rich iron formation bands. The results reveal that the former are enriched in Fe, Mg, Cu, Co and S. The garnet-rich bands are enriched in Mn, Ca, P, Pb and Ba with significant detrital contamination of Ti, AI, Zr, Cr, Y, V, Ni and Nd.The silicate-rich bands have compositions, in terms of, Si/AI, SilFe, FelMn, LalCe and Co/Zn, comparable to submarine chemical sediments which precipitated from hydrothermal fluids. The garnetand amphibole-rich bands are interpreted as ""evolved"" and ""immature"" hydrothermal sediments, respectively. The latter resulted from rapid precipitation after exhalation, whereas the former had a longer residence within sea water. The silicate-rich bands both exhibit increasing Mn/(Mn+Fe) fractions, which are consistent with a variation expected from proximal to distal depositional settings. The prevalence of garnet-rich bands over amphibole-rich bands is interpreted as the result of injection of hydrothermal fluids from a single vent situated along the northwest margin of the Broken Hill deposit."

Jan 1, 1994

By James W. Cameron

DESPITE the fact that, after oxygen and silicon, aluminum is the most abundant and widely distributed element in the earth's crust, it is, commercially, a modern metal. Attempts were made by Sir Humphrey Davy and other chemists to decompose alumina, the oxide, into its elements, but with unsatisfactory results, and it was not until 1827 that Wohler succeeded for the first time in isolating the metal in pure form. Some thirty years later, commercial production of aluminum was started in a plant near Alais, France, using a process developed by Deville which was a modification of that of Wohler. It was not, however, until around 1886 that possibilities of low-cost production were realized. Hall and Heroult discovered, independently, the now famous process for extraction of aluminum by the electrolysis of alumina (Al,O,) dissolved in fused cryolite. This discovery, with its subsequent effect in reducing the price of the metal, was perhaps the greatest single factor contributing to the remarkable growth of the aluminum industry. But only in the years following the Great War did aluminum begin to attain equal importance in many fields with other non-ferrous metals. Numerous factors, political and economic, in the past decade have had a profound effect on the industrial history of the metal. At present, systematic substitution of aluminum for other base-metals is proceeding at a rapid rate in such countries as Germany and Italy with a view towards 'economic self-sufficiency'. Quite naturally, ?the economic depression started extensive research and experiment in various industries in an attempt to improve efficiencies and lower costs. Partial answers have been found in the extended use of aluminum and its alloys. Even against the background of tremendous technological advance that has marked the past fifty years, the rise of the aluminum industry must necessarily stand out conspicuously.

Jan 1, 1939

By Vladislava A. Ignatkina, Victor D. Samyguin

"Within the limits of two-phase approach, considering mass transfer with pulp and air streams was shown that each bubble appears to be an elementary carrier, transporting particles from the collection zone into the froth. The kinetics of flotation was described by the exponential equation in which first order flotation speed constant has to be replaced with two-phased coefficient of a mass transfer. Criteria of selectivity of two ore fractions separation, based on determination of optimum time at which maximum difference between extractions and components content in separated fractions were offered. An interrelation between optimum time of pulp residence in a flowing chamber of a flotation machine, time of bubbles mineralization and an optimum airflow has been ascertained. Cumulative criterion of mass transfer efficiency of flotation process has been ascertained to be a form of the spectrum and its position on axis of three-phase coefficient of a mass transfer.INTRODUCTIONRegularities of a mass transfer of three bearing streams: pulp stream, air stream and froth stream underlie theory of mineral complexes flotation (Samygin, Filippov, & Shekhirev, 2003)However, only description of mass transfer in pulp stream by means of kinetic equations that were simple and convenient for practical use, has gained a full distribution (Tykhonov, 2009;Rubinstein&Filippov, 1980; Saleh, 2010).Within the limits of a single-phase approach, the role of gas stream in increase of speed and selectivity of flotation, was associated with an improvement of hydrodynamic mode. An influence of particles and bubbles sizes (Rubinstein&Filippov, 1980; Rubinstein&Samygin, 1998, Samygin et al., 2003; Dai, Fornasiero,& Ralston, 2000), of pulpflow and airflow (Finch& Dobby, 1990) and turbulent energy intensity (Shubert, 1979; Massinaei, 2007) on the flotation process has been studied. It was stated that flotation selectivity is increasing by means of gradual airflow increase from first to final cameras of the impeller flotation machine (Aslan&Boz,2010; Finch, 2011) and by means of using a multizone flotation machine (Samyguin, Filippov, Matinin, Lekhatinov, &Tertyshnikov, 2013)."

Jan 1, 2016

By Brian E. Robertson

"This paper summarizes work carried out at the Dome Mine to mechanize the mining of narrow veins of less than 1.5 m in width by the introduction of new mining methods and specifically designed electric LHDs.Extensive mining trials have been conducted using sublevel blasthole, modified Avoca, and resuing mining methods. The introduction of the Microscoop and the Jarvis Clark remote, radio-controlled scooptram has increased mucking productivity.As a result of this work, additional narrow vein stopes are now being prepared for production. In the future, narrow vein stoping wil lprovide a greater percentage of the total mill tonnage.IntroductionThe Dome Mine, which is owned and operated by Dome Mines Limited, is located at Timmins, Ontario. Production has been continuous since 1910 and in 1984 was increased from 1814 to 2721 tonnes per day.At least six distinct ore types have been recognized at the mine. In general, these orebodies can be broadly categorized into wide and narrow deposits. The wide deposits are approximately lenticular in shape and vary in width from 10 m to 40 m. The narrow orebodies consist of quartz and quartzankerite veins ranging in width from a few centimetres to six metres. The average dip of the veins is 65 degrees.Since the I970s, mining activity has been largely concentrated in the wider orebodies using highly productive open sublevel blasthole and mechanized cut-and-fill stoping methods. With the demise of shrinkage stoping in 1975, investigations were initiated to develop new mining methods and introduce LHDs - truly designed for narrow orebodies. These investigations resulted in test trials of the sublevel blasthole, modified Avoca, and resuing mining methods. Consultations with equipment manufacturers and suppliers led to the development of the Jarvis Clark remote, radio-controlled electric scooptram and the introduction of the France Loader Microscoop."

Jan 1, 1986

By D. Mas Ivars, K. Suzuki, J. A. Vallejos

"A comprehensive geotechnical characterization has been undertaken at the El Teniente mine to describe and determine the rock mass behaviour strength properties of the primary copper ore. The Synthetic Rock Mass (SRM) modelling approach is used to simulate the mechanical behaviour of this heavily and unfractured rock mass. The micro-parameters of the model have been calibrated against mechanical properties and scaling laws for intact rock and veins, in order to represent virtual samples of four different geotechnical units. Results can be used to predict the rock mass scale effects, anisotropy, and brittleness properties that cannot be obtained using empirical methods.INTRODUCTIONThe primary copper ore at the El Teniente mine is described as very competent and massive, given that it exhibits a brittle behaviour (Rojas, Cavieres, Dunlop, & Gaete, 2000). This description is coherent with the geological description of the rock mass, which does not have discontinuities match as the definition provided by International Society of Rock Mechanics (ISRM, 1981). Only faults can be classified as discontinuities, but they are widely spaced. The primary copper ore has a high frequency of veins, where the cooper mineralization is hosted, these vein network structures are known as stockwork. Soft veins containing weak minerals as infill (chalcopyrite and anhydrite) control the disassembling of the rock mass during caving (Brzovic & Villaescusa, 2007).Presently, there are mainly two traditional methods used to estimate the strength of the rock mass: 1) determination of the strength envelope of the rock mass using scaling parameters from laboratory tests and 2) using numerical modelling based on back analysis of previous experiences of failure observed and measured in mining or civil excavations. The primary copper ore of El Teniente mine has no fractures; therefore, it is difficult to determine a rating that would enable to scale laboratory data, such as, RMR (Laubscher, 1977) or GSI (Hoek, 1994). This is the reason why the first option is not valid unless the entry data is manipulated or adjusted in order to obtain reasonable results. The second option requires, in general, a good characterization of a previous failure event in the rock mass, which is not always available. In recent years, new techniques of numerical modeling have been developed (PFC3D, ELFEN, Abaqus). Those methodologies are the third way to estimate the strength of the rock mass, but they are still in development. Particularly, the concept of SRM developed by Itasca is implemented in this study (Pierce, Mas Ivars, Cundall, & Potyondy, 2007; Mas Ivars et al., 2011), aiming to capture the real behaviour of the rock mass."

Jan 1, 2015

By T. Krumins, L. Zunti, R. Frischmuth

Mercury is known to occur in sulphide-bearing refractory gold deposits in the form of sulphide minerals or elemental inclusions. These deposits typically require an oxidative pre-treatment process, such as pressure oxidation or roasting, to achieve economic gold recovery. However, these processes also have the potential to liberate mercury, a portion of which may then be released to the environment through gaseous emissions. Mercury emissions from mine processing operations have been of particular interest in recent years, as governments impose lower emission targets and organizations adopt better industry practices to reduce the environmental and health aspects of releasing mercury into the environment. This paper describes various mercury removal technologies with respect to pressure oxidation gas handling circuits, with a focus on key design variables and technology selection criteria.

Jan 1, 2014

By R. G. Rosehart, S. Y. Lee

"The current investigation concerns the removal of arsenic from waste waters using ion-exchange resin and activated carbon as sorption media. Use of certain weak and strong base anion exchange resins permits the removal of arsenic. Arsenic may be loaded on the weak base resin in the pH range of 2 to 3 and on the strong base resin above pH 5. The elution of arsenic is successfully achieved using 0.5 M NaCl or a mixture of NaCl and NaOH. The activated carbon investigated was less effective on loading arsenic, but the arsenic loaded was easily eluted by simple pH adjustments."

Jan 1, 1972