Search Documents

By D. M. Muir

Many plants produce iron(II)/(III) waste liquors which must be treated by neutralisation and precipitation to remove the iron. Iron can be precipitated as crystalline goethite or jarosite by controlled oxidation at low pH and as magnetite by controlled oxidation at high pH, but only at elevated temperatures (>70°C). This study focuses on the characterisation and settling properties of the iron oxides produced at ambient temperatures using various neutralising agents in order to improve the performance of thickeners. It was found that two-stage addition of caustic to FeC12 solutions produced a fast settling material characterised by Mossbauer spectroscopy and XRD as maghemite and magnetite. However, lime and magnesia additions resulted in more ferrihydrite formation and much lower settling rates because of the enhanced oxidation of Fe(II) by air. Settling rates decreased significantly as the proportion of Fe(III) to Fe(II) in the liquor increased. The mechanism of iron oxide precipitation is discussed together with some reasons for the different behaviour of the neutralising agents.

Jan 1, 2006

By H. L. Ramandi, P. Moore

"The corrosion of support bolts in underground mines has become an increasingly prevalent issue over the past two decades. With an increase of premature failures due to Stress Corrosion Cracking (SCC), it is evident that understanding the environmental factor influencing the cable bolt corrosion is critical for maintaining effective ground support hence the safety and productivity of underground spaces. Experimental testing of rock and cable bolts were accomplished in a variety of packings, including saturated clay, saturated coal, mine water and grout/cement to investigate their corrosion behaviours. Water samples were obtained and analysed for pH and electrical conductivity (EC) during the experiment. After a period of 76 days the bolts were retrieved and analysed visually. Primary factors were found to be the presence of geological materials and the aeration of the bolts, i.e. the vicinity to air and air flow, while secondary factors were observed to be pH levels and EC. It was also found that the coal/clay interfaces and the water/grout/cement interfaces are non-relevant to corrosion of rockbolts and cable bolts. The proposed framework can be applied to other reinforcement materials used in underground spaces for improved understanding of corrosion environment.INTRODUCTION Rock bolts and cable bolts are the major reinforcement elements used in mining industry to improve the rockmass properties for safe and productive mining. They are normally used to pin large beams or blocks of rock in underground mines to stabilise the rockmass in the roof (strata) against collapse. The rockbolts are typically low cost hot rolled rebar while cable bolts are composed of strands of wire, normally wound together around a central king wire (Hyett and Bawden, 1993; Vandermaat, 2014). The typical length of the bolts in underground mines is 2.4 m and 4–12 m for rockbolts and cable bolts, respectively (Vandermaat, 2014; Windsor and Thompson, 1997). Cable bolts are much more flexible and usually offer a much higher load capacity than rigid rockbolts. Their increased length and flexibility allows cable bolts longer than the height of a roadway to be used in underground mines."

Jan 1, 2017

By Mike Dry, Mani Manimaran, Mykolas Gladkovas, Mariam Melashvili, Chris Fleming

Development of a new hydrometallurgical flowsheet requires quantitative description and optimisation of all chemical processes in each step in the process, as well as mass and energy balances across a fully integrated circuit incorporating all the unit operations. This paper covers steps leading to early modelling of a gold processing plant based on a bromine/bromide lixiviant. Research conducted at SGS Lakefield in collaboration with Albemarle provided the data that were used in the development of this model. A previous investigation in this series described the leaching behaviour of various mineral types in Stabilized Bromine reagent. This paper is concerned with the gold recovery operations associated with a conceptual bromine leaching process. The recovery of gold by different types of resin and activated carbon was studied, along with various methods of stripping the gold from the extractant. The circuit is closed by electrolysing the spent leach liquor to oxidize some of the contained bromide back to bromine that would allow recycling the regenerated leach solution back to the leach step in the process.

Jan 1, 2015

By A. P. Sasmito

It is well known that underground miners are exposed to one of the most dangerous working environments on earth. As mine delve deeper, the geological factor, mine position and climate condition as well as heat generation from mining machine give rise to the mine operating temperature. This, in turn, has an adverse effect on the environment and thus leads to higher operating costs. Careful estimation and design of air flow rate, spray system, cooling load and additional ventilation auxiliary equipment are of importance to ensure safety, comfort and productivity whilst maintaining low operating cost. A computational fluid dynamics simulation approach is employed to examine underground mine ventilation in a 36 m cul-de-sac of tunnel of coal mine. The model predictions in the turbulent range were validated by comparison with published data. Different turbulence models were tested to select one that yields adequate accuracy and is computationally efficient. Effects of the following parameters are evaluated: tunnel geometry, air flow rate and inlet air temperature. The objective of the simulation is to arrive at an optimal strategy for ventilation and thermal comfort at low cost.

Aug 1, 2013

By Frank W. Cole, Sharanjit S. Dhillonn

A new method has been developed for calculating flowing bottom hole pressure in a gas well, using as a basis the general energy equation. Fundamentally, the method shows that a plot of flowing pressure versus depth for a gas well can be represented as a series of incremental .straight lines, with the accuracy in-creasing as the number of increments increase. It is shown mathematically that for most cases the slope of the flowing pressure versus depth curve is essentially constant, in which case a single calculation based on surface conditions will yield acceptable results. In all cases studied no more than two iterations were required for very good accuracy, and in most cases only one iteration was necessary. Several example calculations are shown and the results are compared to other commonly used methods of calculating bottom hole pressures These examples show that the method provides answers which are at least as accurate as other methods usually used, and results in a considerable reduction in computation time.

Jan 1, 1960

By C. H. van Eendenburg

"Installation of a 3.6 km long raw coal conveyor in the Balmer open pit was undertaken to improve over-all haulage efficiency. This paper covers the rationale behind this project, system design and construction aspects and initial operating experiences. The majority of the construction work was performed by our own personnel. Where feasible, used equipment was installed to reduce capital cost and facilitate a tight construction schedule.BackgroundWestar Mining Ltd's Balmer Mine is located in the British Columbia Rockies, just outside of the town of Sparwood in the southeastern corner of British Columbia. The open pit mine, which has been in operation since 1969, currently produces about 6 million clean tonnes of coal per year, mostly for the metallurgical coal export market. Run-of-mine coal tonnages total between 9 and 9.5 million annually and waste removal volumes exceed 30 million bank cubic metres.The mine is a truck/shovel operation; loading equipment includes nine electric shovels, five front-end loaders and a hydraulic backhoe. The truck fleet consists of 40 units of 154-tonne, 181-tonne and 315-tonne capacity. The newer 154-tonne trucks are used for coal haulage for which they have been equipped , with tailgates to maximize their coal carrying capacity."

Jan 1, 1990

By C. Horstmann, D. Andreo, G. Barthold

"The concept of large single line grinding circuits provides a valid answer in project feasibility studies by reducing capital investment requirements compared to parallel lines for the same plant throughput rates. The benefits of this concept are reflected as well on the operational aspects, in terms of higher and greater process stability, and reduced operational costs mainly due to the associated lower maintenance expenditures. However, concerns exist in the minerals industry on whether large single line grinding could reduce the overall concentrator plant availability. The mechanical design and integrity, the mill and gearless mill drive integration, as well as assets management aspects of this type of equipment are the key to guarantee successful availability records. Together with an overview of the added value provided by large single line grinding circuits, this paper focuses on risk mitigation strategies during mill and gearless mill drive integration, as well as on the design of the equipment itself, for the key aspects which could put at risk the operations availability.INTRODUCTIONDespite a large long term demand for commodities, the mining industry has never faced complex challenges as it is doing today. Decreasing high-quality and accessible deposits, declining ore grades in existing mines, shortages of electrical energy (e.g. in Chile) and an aging workforce are the most significant among the megatrends affecting our industry. In addition to this, flat underlying commodity prices and high price volatility are currently posing strong requirements to miners when entering into the process of approving investments.Nowadays to get projects financially approved (optimizations, expansions, new plants), capital expenditure has to be reduced, as observed up to 30% compared to the last decade, and at the same time the plant design has to be such to demonstrate that operating costs will also be significantly lower than in the past.When it comes to the concentrator plant, the concept of large single line grinding circuits provides a valid answer in project feasibility studies by significantly reducing the capital investment requirements compared to parallel lines for the same plant throughput rates. The benefits of this concept are reflected as well on the operational costs, in terms of higher and greater process stability and reduced maintenance expenditures."

Jan 1, 2016

By C. Van Den Heuvel, C. B. Van Buuren

BIOX® has been successfully demonstrated over the past 2 decades for the recovery of gold from refractory sulphide concentrates. To date 12 successful BIOX® plants have been installed in 8 countries spanning 4 continents with the 13th installation currently nearing completion in the Philippines. In 2010 BIOMIN introduced the ASTER™ process for improved water balances in commercial BIOX® applications by supporting tightening environmental legislation on water usage and availability in both arid and tropical regions. Previously, a common challenge for BIOX® plants was the inability to recycle thiocyanate containing water due to the low tolerance of the organisms. ASTER™, a biological thiocyanate and cyanide destruction process, renders a non-toxic solution for re-use in BIOX®. Two commercial ASTER™ plants are in operation with the 3rd ASTER™ plant under construction in the Philippines. A 3rd BIOMIN technology, specifically developed for double refractory ores is available for implementation. The HiTeCC process has shown considerable success on ores where competition from disseminated carbon has rendered ineffective gold recoveries. Through HiTeCC, gold is desorbed from the carbonaceous matter by manipulating the ionic strength and temperature of conventionally treated CIL product. One Australian commercial plant utilises HiTeCC while a 2nd installation is set for commissioning 4th Quarter 2014. BIOMIN’s premier solutions for refractory gold processing are described herein.

Jan 1, 2014

By S. B. V. Stewart, W. W. Forsyth

"Since the Mathew's method for open stope design was first proposed by Golder Associates in 1980 it has been applied at a number of mine sites in Canada. The initial hypothesis was based on a relatively small amount of data and the intervening period has allowed the collection of a significant amount of new data to test the validity of the method.This paper examines a brief history of the evolution of rock mass classification systems to provide background and emphasize their empirical and non-rigorous approach. It also presents the new data which appear to indicate that the initial hypothesis was reasonably good. The modification to the original graph proposed by Potvin is discussed as well as the applicability of the method to predicting the onset of caving. The original graph has been updated and has been subdivided into four zones described as ""stable""; ""potentially unstable""; ""potential major failure""; and ""potential caving"". The method is recommended as a useful open stoping design tool provided it is recognized that it is not a rigorous design method.Finally the paper proposes a recommended approach for application of the method by would-be users and addresses some typical pitfalls that may be encountered."

Jan 1, 1995

By J. J. Denny

IN a preliminary paper (1) it was shown that the addition of small quantities of metallic aluminium powder almost completely inhibited the solubility of siliceous material in the beaker. Six rabbits exposed to quartz dust for six months all showed well developed silicosis. Seven rabbits exposed to quartz dust plus 1 per cent metallic aluminium powder for the same period did not develop silicosis. At that time, we were not in a position to state either the manner in which metallic aluminium reduced the solubility of siliceous material, or, from the animal experiments, whether the aluminium was acting locally or systemically, or for what period after the cessation of dusting it would continue to act. This paper reports the further progress of this investigation. CHEMICAL EXPERIMENTATION The technical details pertaining to the various substances used in the experiments are given in an appendix which is on deposit with the American Documentation Institute, Washington, D.C. For lack of space, it is not printed here. The term 'solubility' is used to indicate the concentration of silica in the solution under the conditions as noted, determined colorimetrically (2), and expressed as parts per million (p.p.m.). The term 'reduction in solubility' indicates the difference between the solubility of the .silica in the presence of the aluminium powder and its solubility in the absence of aluminium powder. It will be noted that the solubility figures for different samples of quartz with no added aluminium vary considerably. The figures do not refer to an equilibrium solubility of silica but to the actual amount of silica dissolved from a given sample in a given time at a given temperature. In view of the fact that quartz dissolves extremely slowly, it is evident that the actual figures in any case will depend upon the surface exposed, i.e., fineness of grinding of the different samples.

Jan 1, 1939

By L. S. Beck

"The Athabasca region forms part of the Churchill province of the Canadian Shield and is underlain by an Archean or Aphebian assemblage of rocks that underwent severe metamorphism and granitization during the Hudsonian orogeny (1750-1950 m.y. ago). In places, the eroded orogen is overlain by unmetamorphosed cover rocks (in-cluding the Martin and Athabasca formations) of probable Paleohelikian age. Basic dykes cut all the rocks of the region.There are innumerable vein-type pitchblende deposits and many syngenetic occurrences of uraninite in crystalline basement rocks. Evidence is presented to show that pitch-blende was emplaced during the final stages of the Hud-sonian granitization and followed the crystallization of syngenetic uraninite transitionally. In terms of P-T condi-tions, the pitchblende deposits belong essentially to Lindgren's mesothermal group.Based on the postulated uranium metallogenesis, the possibilities of finding further deposits of pitchblende and other types of uranium deposits are discussed."

Jan 1, 1970

By C. R. Machado

Sossego Mine was the first Vale SAG mill operation to process copper-gold ore. It is located in the state of Para, in the south-eastern Amazon region of Brazil. In the first six years of continuous operation, Vale investigated different alternatives for improving circuit performance by investigating operating conditions, mainly focusing on the SAG mill. Today, after a steady increase over five years the annual production rate seems to have stabilized. It is hoped this work will show how the SAG operating practice have been perfected with time and as new data are collected. Historical data of mill grind-outs and crash stops helped create operation curves depending on the ball charge volume and total charge volume. Also noted were impacts on throughput due to the effect of reducing liner weight and the ore type characteristics.

Jan 1, 2012

By E. Van Den Neste

A concise historical review is given of the Overpelt plant and the general principles of zinc hydrometallurgy are briefly outlined, together with a description of the new electrolytic zinc plant ore roasting process and, more particularly, the original Overpelt roasting process. A detailed description of the flowsheet of the zinc electrowinning plant, .with an annual capacity of 100,000 t, successfully put into operation in May 1974, is given. The treatment of the residues is performed following the goethite process ; the purification is continuous in two steps; the tank house is equipped with cells containing jumbo cathodes; the handling and stripping of the cathodes is fully mechanized. Concluding the description, some metallurgical and other features of the project are explained in detail.

Jan 1, 1977

By Robert Strachanm

The East Kootenay coal-field, situated close to the boundary between the provinces of Alberta and British Columbia, is composed of four small areas locally called the Crow's Nest Pass, the Upper Elk, the Flathead and Crown Mountain, and comprises an area of about 3 78 square miles. From eleven to twenty-five seams have been exposed of two feet and over in thickness, with a total thickness of about 200 feet of coal, and reckoning about one hundred feet to be workable, gives an estimate of coal available of about thirty-seven billion tons. The coal is a high-grade bituminous, occasionally tending towards anthracite, and the majority of the seams furnish a. very good quality of coking coal as well as an excellent steam coal. The coal-field is found in the mountain ranges in long narrow strips. The age of the fonnation and the thickness of the covering beds have had considerable influence on the character of the coal, and lateral pressure and disturbances in the process of mountain-building have wrought great changes. With such an abundance of coal, it has been a disappointment that the East Kootenay field has not figured larger industrially. So far only one portion of the coal-field has been utilized. This is the Crow's Nest, where, in 1898, the Crow's Nest Pass Coal Company commenced development. Access to the coal seams was easily obtained, the mountain creeks having eroded away the covering, and mines were driven into the coal seams. In that year about ten thousand tons of coal were produced from the mine at Coal Creek.

Jan 1, 1924

By A. G. Roach

HISTORY AND LOCATION SEAL HARBOR GOLD MINES, LIMITED, was incorporated in January, 1934, to take over 116 acres of mining lands in the Stormont gold district, Guysboro county, Nova Scotia. The nearby ten-stamp Mulgrave mill was also purchased, and since that time 974 acres of adjoining properties have been secured from the Government by direct lease. The property is served by a motor road and is about two miles from the village of Goldboro, situated on the shore of Isaac's harbour. The bulk of ?the supplies are brought in by coastal steamer from Halifax, a distance of about 100 miles, since the nearest railway connections are at Antigonish, some 40 miles distant. EARLYY WORK The Seal Harbor properties include the old Partington and Beaver Hat mines. A small tonnage of ore was mined from each and treated on the properties in stamp mills, which were later torn. down . A survey of old records shows that this ore averaged about $8.00 gold per ton. Development work by the present Company was confined to the 100-foot level until February, 1935, but after that rime the incline shaft was deepened to 425 feet and the 300-foot level was explored east and west of the shaft. Six belts of ore were intersected to the west of the shaft. The ore from these belts was hand sorted and the ore portion was put through the 10-stamp Mulgrave mill to defray operating expenses and to serve as a sample of the deposits. The average recovery per ton from this sorted ore was $6.10. Samples of the ore were sent to the testing laboratories of the Mines Branch, at Ottawa, and of Canadian Industries, Limited, at Toronto. Recommendations from both of these authorities were for removal of the coarse gold by concentration and barrel amalgamation, followed by cyanidation of the residue.

Jan 1, 1937

By Han Xing, Cui Jianzhong, Qin Ke, Shao Bo, Zhang Haitao

In this paper, a new approach that uses hot-top DC casting process to producing multi-alloy ingots is present. The different type and size of composite and coated ingots (4045/3004/4045 three-layer composite ingots with section 630mm by 1500mm and 4045/3003 coasted ingot with F140mm/F110mm in diameter) are cast by this approach. The macro-morphologies and microstructures of the composite ingots, the temperature distribution and the element distribution in the interface zone were investigated, also and the interface bonding strength was measured. Results show that the solid supporting layer formed on the cooling plates plays a key role in the casting process of composite ingots. The solid supporting layer can prevent the blending of two melts by resisting the impact of alloy melt, which ensures the stable casting process and casting high quality composite ingots, because the contact height is increased using hot-top DC casting. In addition, fabrication and properties of 4045/3004/4045 three-layer composite ingots with section 630mm by 1500mm are reported in detail.

Jan 1, 2015

By A. G. Mattes

This paper presents an overview of passive, engineered, biologically-based anaerobic bioreactor (ABR) treatment systems of the sort that can be used to remove dissolved copper from mine wastewaters. The paper begins with a brief history of the origins of this treatment technology and continues with a discussion of principles of engineered wetlands (EWs, advanced kinds of constructed wetlands, CWs) and the use of vertical sub-surface flow (VSSF) varieties that contain pulp & paper biosolids as the reactive medium for EW cells. A brief outline of a procedural methodology used in evaluating the potential for biological treatment on a site-specific basis is also included. An introduction to the microbiology of passive biologically-based treatment systems is followed by some recent research results in the general area of wetlands and ABR research. The paper concludes with a brief discussion of several sites known by the authors to have successfully (or not) demonstrated the potential of this treatment option.

Jan 1, 2007

By P. M. Dranchuk

"""PLANET EARTH seen from space appears as a fragile and limited life-supporting system in a vast emptiness. That such a view is, in fact, an accurate one is now more widely accepted than it was not long ago, before Earth's problems of over-population, overconsumption, limited resources and environmental degradation attained the limelight. The danger is that a government and public now deluged by doomsday prophecies and bemused by equally confident reiterations that technology will cure all may hesitate in coming to grips with the problem, in the hope that, given time, it will go away."" With these words, Preston Cloud begins a recent editorial, in Science(l), in which he presents a brief resume of some of the findings of the Committee on Resources and Man of the National Academy of Science-National Research Council(20.Their report, which is based on a two-year study by an extremely competent group and consists of some 250 pages of text, is even more far-reaching and sobering than the report on Energy Resources(3). It begins by quoting Sir Macfarlane Burnet as follows:""There are three imperatives: to reduce war to a minimum; to stabilize human population, and to pre-vent the progressive destruction of the earth's irreplaceable resources.(4)"

Jan 1, 1971

By L. Rodd, C. Walker, T. Koehler

"The energy content of slag represents approximately 80% of the total energy inputs to a laterite nickel electric smelting furnace. Conventional slag handling methods produce only low grade heat and the entire thermal content of the slag is wasted. A heat recovery system proven on BOF slag in the mid 1980's can be adapted to a laterite nickel rotary kiln electric furnace (RKEF) plant. Slag is granulated using a high velocity air jet inside a waste heat boiler to produce slag granules. Granules are cooled during flight via radiation to water-cooled boiler walls and by convection to the granulation air. This system has the potential to recover 80% of the total slag energy in the form of hot air and steam.Integration of the recovered slag energy into the RKEF smelter can be achieved by a number of methods, including the use of preheated air at the ore dryers, kiln or existing power plant. Energy from the slag boiler may be used to reheat boiler feed water from the power plant or to produce superheated steam and generate electricity. The heat recovery system can provide up to 25 - 30% of the total electrical requirement of each RKEF line and a reduction in CO2 emissions of 234,000 tonnes per year.The total cost of slag heat recovery, including CAPEX and OPEX, is $2.5/GJ, which is competitive with using coal when CO2 credits are $18 per tonne. With Clean Development Mechanism (CDM) carbon credits currently selling at €13 ($20 USD) per tonne CO2, there is considerable opportunity for slag producers in regions including South America, Korea, Indonesia and Africa. Increasing fuel costs and more wide-spread legislation for GHG emissions will likely create conditions in which slag heat recovery could generate a favourable return on investment."

Jan 1, 2010

By W C. Shakespeare

The Ontario Committee on Taxation is making a comprehensive study of taxation in the Province of Ontario, and in this connection has received representations concerning mining taxation from a number of interested parties. Some of the more important recommendations on mining taxation are reviewed in this article. Introduction FOLLOWING the appointment of the Federal Royal Commission on Taxation, the Ontario Government, effective in November, 1962, appointed the Ontario Committee on Taxation to review taxes and revenues available to the Province of Ontario and its local governments, to co-operate with the Royal Commission on Taxation and with any other bodies of enquiry appointed by other provincial governments, and to make such recommendations as it sees fit to the Prime Minister of Ontario and the Executive Council. The members of the Committee are: MR. L. J. SMITH, F.C.A., Toronto, (Chairman) MR. ERIC HARDY, Toronto DR. R. CRAIG MCIVOR, F.R.S.C., Hamilton MR. CARL A. POLLOCK, Kitchener MR. R. BREDIN STAPELLS, Q.C., and Toronto. Like its Federal counterpart, the Royal Commission on Taxation, the Ontario Committee has held public hearings, has received written

Jan 1, 1965