Search Documents

By T. Ouellet, F. Chiesa, J. Carignan, D. Levasseur

Common practice for the preparation of permanent mold for aluminum casting is to coat the mold with a ceramic suspension to obtain a chemically stable interface with the aluminum melt. This practice serves two purposes: first, it helps the thermal regulation of the mold and second, it prolongs its life. The possibility of increasing the coating durability by applying it by thermal spray is appealing. Plasma spray of zirconium oxide based coatings was performed on H13 tool steel to study the coating’s thermal fatigue resistance. A unique dip test setup was used to characterize the thermal fatigue resistance of the coatings and of bare H13 steel. Observations of the failure mechanism bring an insight on the requirements of the coating to maximize its durability.

Jan 1, 2014

By Veronique Falmagne

"In 1987 the only knowledge available of the Ansil orebody was that it was high grade, deep and relatively small . High stresses were also anticipated because there had been rockbursts during shaft sinking and destress blasting had been necessary (Fig. 1). From the design, through the development and now in the mining stage, rock mechanics and microseismic monitoring have been used to maximize recovery and safety and minimize dilution. Examples are given of the use of a microseismic monitoring system in the early stages o f mining. This paper also presents a review of the mine's in situ stress measurement campaign, cable bolting practice and backfill procedure.The Design PhaseAfter the initial mapping and classification work, preIiminary numerical modelling was performed using assumed stresses of ov = oH and oH = 3ov• The empirical Mathew's analysis was then used to optimize stope dimensions based on geomechanics data available at the time (Bawden et 01., 1988; Falmagne, 1987; Potvin et 01., 1988). Because of high stresses predicted by numerical modelling and a brittle, strong and relatively unfractured host rock which was believed to be rockburst prone, it was decided to mine without temporary or permanent pillars. However, in order to satisfy production rates, the orebody had to be broken up into two horiwns separated by a triangular pillar (Fig. 2). The final mining sequence is shown in Figure 3.The Development PhaseAt this point, based on work accomplished to date, including mapping and observations from drifting and modelling, the following problems were identified: (1) flat backs in the hangingwall andesite were thought to be highly stressed; (2) flat backs in weak massive sulphide ore would also be subjected to high stress and be difficult to support; (3) the felsic dyke was noted as a "" stress raiser"" , because activity increased as drifts approached it; and (4) chlorite coating of joints in the hangingwall was thought to be an important factor in reducing their stability."

Jan 1, 1991

By E. Barnard, J. Tero, J. Rajala, N. Avenido, M. Fullam, A. Nashitati, S. Mbalamba

"The Otjikoto mining and milling complex is 90% owned by B2Gold Corporation, and began commercial operation on February 28, 2015. The milling circuit operates at a throughput 3.3 million tonnes per annum, with an average reserve gold grade of 1.28 g/t. The ore is high in Gravity Recoverable Gold (GRG), which varies between 73-91%, depending on ore type. Overall gold recovery since start-up is 98.2%, with about 63.5 % coming from the gravity circuit as doré. 2016 cash operating costs, and all in sustaining cost (“AISC”) were $361 and $604 per ounce, respectively.During design, three ore types were tested for GRG content, and based on the high GRG value of all three ore types, the decision was made to treat the full ball mill circulating load by gravity. Once operating, the gravity circuit performance was characterized by performing a detailed gravity audit, which included the ore, cyclone classification, Knelson concentrators, and the Consep Acacia intensive leach system. The deeper ores contain significant pyrrhotite, and this created some unusual challenges that had to be overcome. This paper presents the gravity circuit design process, the circuit commissioning, and the audit results and ongoing improvements.IntroductionHeadquartered in Vancouver, Canada, B2Gold Corp. was founded in 2007. Currently, B2Gold has five operating mines, and numerous exploration projects in various countries, including Nicaragua, the Philippines, Namibia, Mali and Burkina Faso. The Otjikoto Mine is located in the north-central part of the Republic of Namibia. It is situated approximately 300 kilometers north of Windhoek, the country’s capital, within the Province of Otjozondjupa. The Otjikoto mining and milling complex is 90% owned by B2Gold Corporation, and began commercial operation on February 28, 2015. The milling circuit operates at a throughput 3.3 million tonnes per annum. During design, a large emphasis was placed on gravity recovery, as the Otjikoto ores are unusually high in Gravity Recoverable Gold (GRG)."

Jan 1, 2018

By T. Güyagüler, U. Y. Önder

"This study investigated the psychrometric properties of ventilating air in GAL coal mines. Related measurements were done in underground openings and have been arranged as input data for computer programs prepared for ventilation network and psychrometric analysis.Results obtained from network analysis have been used for psychrometric analysis of ventilating air. Changes in heat and moisture content of air in two major path s between entry and discharge of ventilating air have been investigated. Psychrometric processes occurring in the mine were determined and are shown graphically in Figures 1 and 2. Special attention has been given to determine the changes in psychrometric properties and processes involved in the faces. Results are outlined in this paper.IntroductionThe psychrometric properties of mine air are important factors to mine productivity and efficiency. Therefore, psychrometric analysis should be made for all underground mines; any undesired situation observe d could be corrected by taking the necessary precautions.The analyses were done as a case study for GAL mines, the only mechanized lignite coal mine in Turkey. In this mine, workable reserve is about 300 million tons of coal and yearly planned production is 2.2 million tons. Production is continuing from a coal measure-bed having two coal seams with average thicknesses of 1.52 m and 1.72 m respectively. A 0.85 m shale band exists between these two seams.Two full y-mechanized faces, approximately 220 m long, usually work simultaneously. All measurements, including mine gases and air velocity, are done by sensors connected to a control room by a monitoring system.In the analysis, a line diagram is utilized to described the mine on which every junction and branch is numbered."

Jan 1, 1992

By A. LA. Salama, D. B. Hyma

"The Western Research Centre (WRC) of CANMET located in Devon, Alberta, is a modern research facility offering services ranging from fundamental research to pilot plant investigations. Recently, a 0. 76 metre diameter by 7.9 metre high Flotaire column flotation cell was installed as a demonstration unit for Canadian coal producers. Because the column cell is intended to be used for research, development and demonstration, WRC recognized that additional sensing equipment and improved process control would be required to generate good data for subsequent column scale-up and engineering design.A low cost, personal computer based control system was, therefore, designed and installed. This paper describes the stepwise procedure in developing the control strategies, selection of system software and hardware, and installation and configuration of the system.Preliminary performance data on a western Canadian coal sample are also presented. Future testwork is planned on additional coal samples to expand upon existing database."

Jan 1, 1993

By W. H. Moore

It seems necessary, at times, that we should reconsider some of the more obscure causes that lead to explosions of gas and coal-dust in mines, in the hope that a recapitulation will keep before us that old and true saying "eternal vigilance is the price of safety". This explosion, while not extensive (resulting in only two much to be regretted deaths) enlarged our vision as to the possibility and probability of other explosions with more disastrous results. As this is only a partial report I shall have to omit many things that are generally included in describing a mine explosion. The mine was worked exclusively with electric cap-lamps -only firebosses and other officials carried safety-lamps. All shots were examined and fired by firebosses with a small hand-battery. Monobel was used exclusively for blasting, and clay for tamping. The system of haulage iri use was main-rope and winches, horses being employed for gathering. Compressed-air was the motive power for all winches and pumps, excepting the pumps at the shaft-bottom which were steam-driven. The mine was wet with practically no dust anywhere, except what was being made at the coal-face in the getting of the coal. Gas was found occasionally, generally in the brushing, especially where the brushing was carried up to a small seam, 2 to 6 feet above the main seam. The place where the explosion took place was known as Leigh's heading, which was being driven to the rise, immediately inbye of the siding (off No. 1 left, off the new slope) and was about 90 feet up from the level.

Jan 1, 1926

Weekly Capacity ? Current Schedule Rate (198.5 tonnes / hour) X Skip Time (112.7 hours) X Effectiveness (85%) = Weekly Capacity (19,015 tonnes) Capacity Conclusions - Existing hoists optimized are best option for Fraser Morgan (>20M + schedule for other). - Peak will have to be managed. - Critical to have equipment & infrastructure in best possible condition to ensure reliability.

Feb 1, 2008

By Hugh K. Taylor

"With some justification, people have long complained about the indefinition of ore reserves. Perhaps they were led to expect too much; from former and easier definition practices in the once common underground mines with exposed and available assets, where the obsolete term 'ore in sight' was at least partly literal. But such mines have become rarer, and their underground development less affordable. For most projects, valuations and its definitions have thus been advanced from actual to prospective mines, leaving a very wide gulf between 'what is there' and 'what may happen to it'. This brings the double challenges of reduced geological and technical assurance and the protraction of economic uncertainties.This paper avoids the popular field of regional resources, being confined to what may possibly be mined within single or closely grouped deposits. For these, many estimates of tonnage and grade must be made, defined and declared long before assessment of feasibility; and the uncertainties of the latter make it an unsound base for defining the earlier quantities. Despite the best of intentions, implied or inferred promises may proveimpossible to honour.A simpler framework of definitions is suggested, to some extent reverting to an earlier dependence on supporting work rather than on opinions of economic assurance or future events that are more properly the functions of production and cash flow schedules."

Jan 1, 1994

By Minghui Li

China is the largest coal producer in the world. In 2012, the coal production in China is 3.65billion tonnes, accounting for approximately 49% of global coal production. The raw coal production in 2012 was 3.8% more than the year 2011. 56% of total raw coal has been washed. The increase in raw coal production also promotes technology to be developed and brings separation capacity become larger and larger in coal processing in China. At present, over 40 extra-large scale coal preparation plants (each plant has capacity of more than 10 Mtpa) are in operation in China, the largest one is 32.5 Mtpa. Heavy medium separation are widely used in new built coal preparation, the washing limit for thermal coal feed lower and lower, the equipment selection tends larger which brings the whole washing system simplified, the local equipment developed and manufactured are more and more used. By discussing designs of several typical thermal coal preparation plants and coking coal preparation plants in China, this thesis introduces the current design of China?s extra-large coal preparation plants, and sums up the prevailing design features and trends of extra-large coal preparation plants.

Aug 1, 2013

By M. du Plessis, D. F. Malan

"Crush pillars are designed to be in a crushed state whilst being formed at the mining face. The residual stress state of these failed pillars provides a local support function in mining stopes and is used in the majority of the intermediate depth South African platinum mines. On mines utilising crush pillars, the pillar dimensions are selected to achieve a width to height ratio of approximately two. This is not achieved in most cases as a result of practical mining problems and poor pillar-cutting discipline. Furthermore, pillar dimensions are seldom adjusted to compensate for the various factors governing crush pillar behaviour. The pillars should, however, be in a crushed state whilst being formed or whilst still in close proximity to the mining face to prevent potential damaging seismicity.An underground investigation was conducted into the behaviour of the crush pillars in a trial site on the Merensky Reef at Lonmin Plc. The aim of this investigation was to examine the mechanism of pillar crushing and the related rock mass behaviour. The underground test results and pillar behaviour are compared to a limit equilibrium model to investigate if the model provides a useful approximation of the behaviour of the crush pillars. This paper details some of the preliminary findings.INTRODUCTIONOn most mining operations, the design of crush pillars is based on trial and error. As the pillar strength is unknown, the pillar sizes are adjusted to obtain the correct behaviour. Crush pillar dimensions are generally selected to give a width to height ratio (w:h) of approximately 2:1, (Ryder and Jager, 2002). Several factors affect the behaviour of the crush pillars and in many cases satisfactory pillar crushing is not achieved. This results in a seismic hazard in many of the mines using crush pillars. If pillar crushing is not initiated whilst the pillar is being formed at the mining face, as the mining face advances and the pillars move to the back area of a stope, some pillars may burst while oversized pillars may punch into the footwall. If pillars are designed in such a way that they are fractured during cutting by the face abutment stresses so that the pillars will already have yielded and reached their residual strength, further compression of the pillars will be associated with an increase in load and stability will be ensured, (Ozbay and Roberts, 1988). The stiffness of the strata must therefore be greater than the post-peak stiffness of the pillar (Figure 1) or violent pillar failure and hanging wall instability will occur. The pillar design should be aimed at determining pillar dimensions for which the post-peak curve of the pillar is as flat as possible."

Jan 1, 2015

By C-D. Johansson, B. Ögren, B. M. Ludvigsson, K-Å. Johansson, R. Lindh, G. Berg, M. Maliarik

This paper presents the High Current Density (HCD) Silver Electrorefining Process. A 25-year history of development of the silver electrorefining process as well as associated equipment is given. The process is simple and robust, but at the same time highly automated. With low operating costs and man power requirement it allows consistent production of 99.99 % quality cathode silver. The process ensures that no toxic gases are formed in the working environment. Silver Electrorefining is a heart of a Silver Refinery plant covering the complete range of processes from casting of silver Doré anodes to casting of the bars of refined silver or/and silver granulation. The process has been successfully applied at 11 installations world-wide with plant capacities ranging from 30 to 1500 tpa.

Jan 1, 2014

By Raymond D. Potts

"Minntac is a taconite mining, concentrating and pelletizing operation located near the town of Mountain Iron, Minnesota, U.S.A. It is totally owned and operated by USX Corporation and represents its largest source of domestic iron units. Minntac began producing fluxed pellets in 1988 and has produced both acid and fluxed pellets since then. This paper compares the acid and fluxed pellets produced at Minntac. It reviews modifications that have been made to the plant flowsheet and discusses areas recognized for improvement since the beginning of fluxed pellet production. It also comments briefly on the performance of Minntac fluxed pellets in USX blast furnaces and the future of fluxed pellets at Minntac.IntroductionMinntac was built in three steps with each step designed to produce 6 million long tons of acid pellets per year. The actual production has varied though. Figure I shows the production by year at Mirmtac. Step I began production in 1967, Step 2 in 1972 and Step 3 in 1978. Mirmtac produced 16.5 million tons in 1979 but only 3.5 million tons in 1982 when the facility was shut down for six months because of the lack of demand for pellets. Since the initial start up, Mirmtac has produced over 200 million long tons of pellets. Until 1987, all the pellets produced were ""acid"" pellets. In 1987, equipment to produce ""fluxed"" pellets was installed and tested. In 1988, full scale production of fluxed pellets began."

Jan 1, 1991

By W. F. Harkness, D. Hodgkinson

"A non-destructive testing program was established at Crows Nest Resources (C.N.R.), Line Creek mining operation following an in-service fatigue failure of a front wheel spindle on a large haulage truck.This failure identified a definite need for improvements in the ultrasonic techniques used during the mandatory spindle integrity examinations. Initial investigations using common mining industry ultrasonic examination techniques showed that the smallest detectable cracks were 75 mm in length for the spindle types in service at the C.N.R. site. The Initial findings indicated that inadequate inspection technique design was the cause of the poor performance. To improve inspection reliability it was identified that improved ultrasonic techniques were required. Results using designed ultrasonic techniques were encouraging, with the detection of simulated and natural cracks 12 mm long achieved. The cost benefits associated with the extended spindle life, following the removal of these small fatigue cracks, far exceeded those of the expertise and effort necessary to implement and conduct the N.D.T. program.Introduction During 50 years of evolution, non-destructive testing (N.D. T.) has progressed from a laboratory curiosity to a well accepted and invaluable tool used in the assessment of material integrity. Unlike destructive testing, N.D.T. does not deform or render the material useless. Non-destructive tests may involve many applications, from the determination of a corrosion prevention coating thickness to the examination of a raw material for internal and external deformities.Within the mining sector, highly-stressed components will normally have been subjected to some form of non-destructive test during their manufacturing cycle. These tests are used to ensure the component does not contain material flaws whichmay be detrimental to its service performance.While the component may have assured quality when produced, deterioration by fatigue may occur during an aggressive service life. Large dynamically-loaded components such as haulage truck front wheel spindles are , in particular, prone to this service related problem."

Jan 1, 1987

By C. H. B. Leitch

"The Bralorne-Pioneer deposit produced more gold than any other deposit in British Columbia over its 70 years of operation (130 kg or 4 million oz of Au, from 7 million tonnes of 18 glt ore). Mineralization is related to a suite of late Cretaceous albitite dykes of 85 to 90 Ma age. It thus occurred long after and is genetically unrelated to the Early Permian (275 Ma) Bralorne diorite and soda granite.The major veins strike about 110 degrees and dip north at 70 degrees, with slickensides plunging 45 degrees east that indicate last movement was reverse. Major ore shoots in the veins occupy somewhat less than 20% of the vein and plunge steeply west, roughly perpendicular to the slickensides. The structures that contain the veins probably formed at around 95 to 90 Ma during a strike-slip episode with easterly directed maximum compression.Disseminated pyrite, pyrrhotite, and minor chalcopyrite occur within envelopes up to several metres from the veins. Arsenopyrite is confined to vein selvages. Local sphalerite and galena appear to correlate with gold-rich portions of the veins. Traces of tetrahedrite and stibnite have been observed but tellurides have not. Gold is found principally as thin smeared flakes of the native metal in the black sulphidic septae of the strongly ribboned veins. Hydrothermal alteration envelopes around the veins grade outwards from intensely foliated quartz - ankerite - sercite (±fuchsite) to less sheared calcite - chlorite - albite to unsheared epidote -calcite.Open-space vein filling textures found in the deep (mesothermal) environment at Bralorne can be explained by a fault- valve model. High-angle reverse faults may have acted as fluid-pressure activated valves on geopressured reservoirs, causing large cyclic fluctuations in fluid pressure that promoted mineral deposition in an episodic fashion . The faults that were mineralized were reactivated sub-vertical former strike slip faults, oriented at a high angle to the northeast-directed stress in a compressive regime."

Jan 1, 1990

By Lynne Bowen

"On the da y shift in Number One Mine at Nanaimo on Vancouver Island, on May 3, 1887, William Griffiths, a coal miner with many years experience, fired a shot to advance the face of the crosscut. A flame ran out for a distance of fifteen feet along the roof and then extended up the slope for ten to twelve feet, and although many would have called this a blowing out shot, Griffiths said it was just a feeder. ""A blower"", he said, ""would have caused an explosion."" 1There was no explosion. Griffiths reported gas and the area was cleared for three hours and then work resumed. When the shift changed at 3:00 p.m., the fireman reported all places clear of gas and the ventilation good.2The ventilation in Number One Mine was the best anyone had ever seen. The air in the mine was almost too cold. The current was so strong that it sometimes blew out the flame on the miners' fish oil lamps. It delivered five to six hundred cubic feet of air for every man and animal working in the mine. The law required only one hundred cubic feet 3The miners considered Number One to be relatively safe. The manager was proud of the mine and its up-to-date equipment"". Recently, there had been reports from France and America about the explosiveness of coal dust, but the manager did not think his mine was sufficiently dusty to be dangerous.5 The dust lay thick on the floor of the mine. Sometimes when a shot was fired the dust rose in great clouds. When a miner was shovelling it, the dust would billow up and be carried off by the current of air. The dust was also in the roof and in the stopings, put there intentionally to fill up the spaces and prevent the accumulation of methane gas."

Jan 1, 1992

By Alan Reed

"Afton Mines Ltd. (N.P.L.) operates an 8500-tpd open-pit copper-gold mine near Kamloops, R.C. The pit is currently 480 feet deep and will reach an ultimate depth of 800 feet. The east, south and west walls of the pit are composed of Triassic andesites (Nicola Volcanic Formation) and contemporaneous sub-volcanic intrusions of micro-syenite, microdiorite, diorite and picrite-basalt (Iron Mask Pluton). The north wall of the pit consists of Tertiary sandstones, shales and mudstones (Tranquille formation) and dacitic dykes, sills, flows and tuff s (Kamloops Volcanic Formation).The Afton copper-gold orebody (30 million tons of open-pit ore with a grade of 1.0 per cent copper, 0.016 oz/ton gold and 0.12 oz/ton silver) occurs within the Triassic Iron Mask Pluton adjacent to its faulted contact with Tertiary rocks. The Triassic-Tertiary contact is a complex fault system dipping 65 degrees southward and causing the Triassic rocks to overlie the Tertiary rocks. The detailed trace of this contact is very intricate due to the mutual interference of three principal fault systems.The dominant geological structures in both Triassic and Tertiary rocks are faults striking WNW and dipping 65 degrees southward, i.e. sub-parallel to the orebody (strike faults). Cross faults and oblique faults are abundant and highly significant in some sectors of the pit. The Tertiary sedimentary rocks show an early series of northwesterly plunging folds deformed by a later series of northeasterly striking folds. Major lithological and structural boundaries divide the pit into 8 structural domain s within which the pitwall slope stability is controlled by the local geological structures and lithology.Assay data from production blasthole samples and exploration diamond drillhole samples show a log-normal frequency distribution, with a fairly low relative variance. Variograms computed from production blasthole samples show good continuity with elliptical horizontal zones of influence which are truncated by the major faults that bound the ore zone."

Jan 1, 1983

By Chenming Liu, Xiao Lin, Bo Wang, Hongbin Cao, Xingang Li

Over 2 million tons of NH3-N were discharged in China per year recently, rare earth industry contributed 7.03% of NH3-N pollutant from industrial wastewater in 2007. Wastewater containing NH3-N and heavy metals mainly produced in RE extraction saponificated with ammonia and precipitated by ammonia bicarbonate. Generally, 1 ton REO cost 0.6-1.2 ton ammonia for extraction and 1.6 ton ammonia bicarbonate for precipitation, and produce 35-100 ton wastewater. Processes, like Na-saponificated, Ca-saponificated and Non-saponificated technique, are widely studied to reduce the adverse environmental effect of RE industry, while traditional processes still have advantage in production cost, process stability and product quality. In this study, a novel process that combines distillation and air-stripping is developed. NH3-N is removed and recovered based on relative volatility difference of NH3 and H2O. Phase equilibrium, heat equilibrium are calculated to determine process parameters. Hydrodynamic performance like flow field distribution is also simulated. Then, design parameters for distillation trays or structured packing are determined based on calculations and simulations. Besides, the phase diagram of (NH4)2SO4-NH4Cl-H2O in 30°C - 100°C, the typical salts composition of nonferrous wastewater, is studied to ensure commercial plants’ continuous operation. Ammonia removal tower (ART) with different high efficient column internals is designed to fit RE wastewater treatment requirement. The novel process has been commercialized in RE industry in Jiangxi, China. The commercial project operation results show the novel process reached a nearly zero-emission with >99.5% NH3-N was removed and then recovered as ammonia. Combined the novel process, the traditional REO separation process using ammonia and ammonia bicarbonate could achieve NH3-N reuse and the effluent quality meets the discharge standards.

Jan 1, 2016

By Peter J. Franklin

"Short-term mine planning of open pits is an activity that has historically been carried out by hand. Typically, the use of computers has played little part in this type of mine planning. This paper describes the objectives and the procedures involved in short-term mine planning, comments on the type of computer systems available, and describes in detail a computer-aided short-term planning and scheduling system known as STEPS.IntroductionThe mine planning department of any o pen-pit mining operation performs a wide variety of different tasks. However, their primary concern is the preparation of detailed long-and short-term mine plans. These mine plan s will define the long-term operating strategies and definitive everyday working plan s for the ongoing development of the open pit.In this day and age, when operating costs have spiralled upwards due to inflation , and product revenues have decreased due to depressed economies and poor markets, it is vitally important for all aspects of the mining operation, including mine planning, to be efficient and cost effective.There are numerous options available for planning engineers when generating a mine plan. A cost effective mine plan must investigate all these options and select the optimum. When using manual planning techniques, it is often impossible to evaluate all the available options. To do this, and to produce an optimum mine plan, a computer is required.This paper discusses mine planning, with emphasis toward the short-term plan and comments on how the processes may be computerized. It also describes in detail, a computer software system called STEPS, which has been designed as an interactive graphics, computer-aided short -term mine planning and scheduling tool."

Jan 1, 1985

By S. P. Narayan

The hot deformation behavior of Pure Mg and Mg-0.29Ce alloy were studied by isothermal hot compression tests in the temperature range of 250 - 500°C and strain rate range of 10-3 - 102 s-1 in a computer-controlled 50kN servo hydraulic universal testing machine (UTM). The results show that the flow stress of Mg pure and Mg-0.29Ce alloy increases with strain rate and decreases after a peak value, indicating dynamic recovery and recrystallization. Process efficiency was increased by nearly 10 to 12% by addition of Ce in Mg. Mg pure exhibits instability zones between 250-275°C at 10 ? 102 s-1 and 400¬500°C at 101 ? 102 s-1 temperatures and strain rates respectively, rest is the safe deformation zone. Wherein, Mg-0.29 Ce exhibits two low efficiency zones from 250 ? 300°C at 10-2? 10° s-1, 400 ? 500°C at 101 ? 102s-1 and high efficiency zone at 450 ? 500°C at 10-3? 10-1s-1. 4D process maps were generated for the above said alloys which illustrate contours of power dissipation and instability in the 3D space of strain rate, temperature and strain.

Jan 1, 2011

By C. M. Clapperton, K. E. Darke, A. J. Boyce, C. M. Rice, S. D. Redwood

"Abstract - The Kori Kollo gold deposit is hosted by a c.15 Ma sericitized dacite stock in the La Joya district on the Bolivian Altiplano. The mineralization is of the Bolivian polymetallic vein (BPV) type, with a significant amount of the gold reserves contained in the oxide cap. Field and microscopic studies, K-Ar dating, ??34S values of pyrite, alunite and jarosite, and ??18O values of alunite and jarosite demonstrate that some of this gold is supergene. Two types of supergene gold are present: minute gold grains, 1 to 10 microns across, of high fineness and associated with jarosite and iron oxy-hydroxides; and ‘invisible’ gold, which is probably sorbed onto minerals such as jarosite and iron oxy-hydroxides.Pyrite ??34S values fall in the limited range -3.5 ± 0.6‰, consistent with a magmatic origin. Sulfate ??34S values are homogeneous and overlap closely with those of pyrite (-1.2 ± 2.1‰), which supports petrographic evidence that sulfates replaced pyrite. By contrast, sulfate ??18O values are inhomogeneous with a large range (alunite +2 to 26‰, jarosite -5 to +18‰). These data are interpreted as reflecting kinetically controlled reactions involving various proportions of atmospheric oxygen and local meteoric water. This is typical of supergene alteration and is due to the seasonally dry climate of the Altiplano.The oxide-zone mineralogy is dominated by sulfates and iron oxy-hydroxide minerals with some phosphates and halides, which indicates that the groundwaters were acidic, oxidizing and relatively saline. Under these conditions the most likely complexes responsible for gold mobilization are halides.Geological data and K-Ar ages indicate that oxidation of the BPV deposits began at least around 11 Ma and possibly up to 15 Ma ago, and that supergene alteration lasted until around 4 Ma. During this period, erosion was minimal. Although supergene processes have been active on the Bolivian Altiplano since the Middle Miocene, in contrast to Northern Chile, enrichment of gold has not occurred."

Jan 1, 1997