Search Documents

By R-H Yoon

Increasing the upper particle size limit of flotation would allow operators to increase mill throughput, save operating costs, simplify flow sheets, and increase rate of return. However, coarse particle flotation is difficult for various reasons, of which bubble-particle detachment has been identified as the major limiting factor. In the present work, the process of bubble-particle detachment has been studied by directly measuring the forces required to detach air bubbles from hydrophobic solids. The measurements were conducted using a hanging balance apparatus. The measured forces were converted to detachment energies that can be compared with the work of adhesion, which in turn is a function of hydrophobicity, surface tension and contact area. The results were converted to detachment energies using the Young-Laplace equation for capillarity. In the present work, the solid surfaces were hydrophobised by coating them with octadecyltrichlorosilane and cetyltrimethylammonium bromide. The results show that bubble-particle detachment occurs in two steps. In the first step, air bubbles are deformed, while the three-phase contact (TPC) line is pinned, until contact angle reaches advancing angle. In the second step, the TPC line moves along the surface until solid/air interface is replaced by solid-liquid interface. In general, the energies of detachment measured in the second step are in good agreement with calculated work of adhesion. Thus, the energy required during the first step effectively represents an energy barrier for bubble-particle detachment. It has been found that the energy barrier varies with surface roughness and surface tension. The results of the present investigation suggest, therefore, that coarse particle flotation can be improved by control of particle hydrophobicity, surface roughness, and surface tension.

Jan 1, 2005

By Patridge A. C

A pilot scale laboratory investigation of manual slurry sampling methods representative of those used in the minerals industry is described. Samples were taken from slurries made up from silica particles of various sizes and in various concentrations from a stirred tank and from the discharge lip of a rectangular launder. Sampling methods from the tank included immersion flasks and several configurations of a suction probe. The launder was sampled using a conventional narrow-mouth ladle and also with a 'mouth organ' stream splitter. Samples were analysed for overall solids concentration and size distribution and showed different but always significant and often large biases relative to the known overall composition of the slurry, the nature and extent of bias being dependent on pulp concentration, particle size, sampling method and sampling location. Results clearly show the very great difficulty of obtaining representative samples by simple sampling techniques, although the data suggest that errors can be reduced by using an appropriately designed and operated suction probe. Further work will be carried out with the objective of establishing guidelines for industrial sampling practice.

Jan 1, 1995

The type of population encountered in the sampling of coal, ores and other products of natural phenomena is one in which the variance within a cluster of elements generally increases steadily as the size of the cluster increases. To enable estimation of variances of stratified random or systematic sampling for such populations one must model the serial correlation function or alternatively, the variogram function. The author has postulated a specific symmetry of the serial correlation function which leads to expressions with rich theoretical and practical implications. These expressions provide a spatial correlation function which explains power law relationships often observed in studies of dispersion variances. They also enable straightforward calculations of sampling variances. The importance of the role of finite population size in the equations leads one to examine previously held concepts of ælargeÆ and æsmallÆ sample populations. The model based on the symmetry postulate is a fractal model with the serial correlation function of a hypothetically infinite population being of the same form as that developed by Mandelbrot for discrete fractional noise. Techniques used in fractal mathematics apply, including box counting and fitting of a dimension function. The paper establishes a framework for the understanding of this fractal theory and demonstrates how to calculate sampling variances from the model variogram using simulated data fitting the model.

Jan 1, 2008

It's my privilege to welcome you here this afternoon on behalf of the Sydney Branch of the Australasian Institute of Mining and Metallurgy. This is a most important gathering. You, the delegates, represent what is probably the most influential cross-section of the mining investment community and the oil and gas investment community to meet as a group during the last decade. We are meeting today and tomorrow to review two related issues that will have far reaching implications for the effective use of capital by the natural resources sector in the 1990's. The views which will emerge over the two days will almost certainly 'influence the availability of new capital to the companies in the natural resources sector for the decade ahead. The two principal themes of Minval '89 are, first, the valuation of mining and oil and gas assets and securities, and second, disclosure and reporting requirements in the capital markets which relate specifically to natural resources companies. This conference is taking place at a time when further consolidation and rationalisation appears likely within the mining industry. Although the base metals and other sectors of the industry are enjoying profitability not seen since the early 1980's there is caution about committing to new capacity which could bring about a return to the low prices and excess supply which prevailed during much of the last ten years. These conditions have led to increased takeover activity within the mining industry overseas, and similar trends are as evident here in Australia as they are elsewhere. Recognition of value is therefore likely to become more important than ever before in preserving shareholder wealth, for creating new wealth and for preserving the financial health of the resources industry in the future. Valuation therefore is the first theme of the conference.

Jan 1, 1989

Much of the data required for the evaluation of mine design is obtained from bore cores. It is essential to collect data that is useful and not to overlook features which might have adverse effects upon the mining practices and which might not be readily discernible to the untrained eye when examining bore cores. Interpretation of the data has progressed from the use of single-value properties, such as ultimate compressive strength or Young's modulus, to the utilisation of most measurable quantities. The simulation techniques used employ physical and mathematical models for prediction of mining conditions or strata behaviour. The application and capabilities of these methods to mine design are discussed.

Jan 1, 1977

By Braham B

The Australian mining industry isstill labouring under the impression. created by the Fitzgerald Report that it does not pay suffic- ient tax. This would appear to be the raison d'etre of the resource rent tax debate. The authors quantitatively compare the cash flows to the mine and government resulting from a large strip coal mine in central Queensland under a number of Australian and international taxation policies. The Liberal government policies are found to be internationally competitive while the Labor 1975 policy is excessively punitive. The present value of the returns to the public from the Liberal 1977 policy vary between three and six times the net present value to the mine, which belies the necessity for the imposition of a super tax. The levelling of a special royalty, excess rail freight, by Queensland could severely re- strict the development of new mines in the Bowen Basin. The impact of excessive freight rates is analysed on a combined strip-deep mine typical of the new projects nearing development in the region. Otherwise economic mines can be made marginal or even sub economic by this tax. Even with moderate rail freights, the mining tax laws of New South Wales are more favourable to the industry than are Queensland's.

Jan 1, 1978

By Whiten W. J

Data from ball mills of a wide range of sizes are analysed using detailed mathematical models and non-linear least squares fitting techniques. In this way model parameters are obtained describing the behaviour of ball mills over a wide range of mill sizes and operating conditions. These parameters define the flow and breakage of each size fraction of ore in the mill. Flow of coarse particles through the mill is found to depend on the proportion of coarse particles present. The breakage rates of coarse particles are found to decrease markedly with mill diameter for mills over 3 m in diameter.Simulation of grinding circuit throughput at constant productsizing for different mill diameters shows that throughput is proportional to theoretical mill power consumption for mills up to about 3 m in diameter. Thereafter the throughput gradually falls below that indicated by power consumption, the decrease becoming quite significant for large diameter mills. Simple qualitative physical arguments are presented to explain this behaviour. The models developed have applications to ball mill scale up. Work on their further development is continuing.

Jan 1, 1982

THIS excellent volumetric method commends itself as a means of estimating the fineness of silver firstly, owing to the large number of possible impurities which do not affect its accuracy (these impurities include Cu-up to 70 % Au, Ph, Zn, Bi, Cd, Fe, Mn, Sb, and As); secondly, the method combines accuracy with speed. The above impurities are the only ones likely to be present in the B. H. A. S. Pty. Ltd. refined silver, and, with the exception of Cu and Au, the others, if present at all, would be well under 0.1 parts per 1000.Briefly stated, the method consists in the solution of the refined silver in HN03 , addition of ferric alum (indicator), and titration with an alkaline (either ammonium or potassium) thiocyanate solution until the brown ferric thiocyanate is formed, and gives a definite tint to the solution. The method is used at the Port Pirie smelters, and the outstanding feature in the method as there applied is the type of burette employed. This burette enables the operator to read 0.01 of a cc. with ease, whereas, with the ordinary burette fitted with a float, 0.05 of a cc., when a number of readings have to be taken, becomes very straining to the eyes. Moreover, waiting for the float to rise, and dislodging air bubbles from it, hinders rapid working.A description of the burette and fittings is appended with fig. 2. DETAILS OF THE METHODSolutions required are:a) Stock Solutions:(1) Ammonium thiocyanate, 40 grm. per litre of water; 30 litres are prepared and placed in a carboy with glass syphon attached.(2) Ferric alum, 250 grnl. per litre; two litres are prepared.

Jan 1, 1922

By A Domanti, C Jewkes

This paper describes the design and constructability issues investigated in the selection of a trenchless solution in comparison to trenched construction options as part of a scoping study for the augmentation of the existing Bulimba Creek Trunk Sewer in Brisbane. Initial work involved the planning of alignment options vis-a-vis ground geology, geotechnical conditions, location and depth of shafts considering potential construction technology, flotation and stability of the tunnel, availability of construction sites and the influence of construction works on neighbourhood properties and the immediate environment. Two design pipe sizes, DN1200 and DN1500, were considered, and factors including jacking forces, specification of product pipes, pipe joints, pipe jacking methods and the associated impacts of ground settlement were carried out. Of particular interest was research on suitable lubricating fluids with the potential to minimise jacking forces and maximise the length of pipeline between launch and reception shafts.

Jan 1, 2008

By D Smith, D Reid, D Bradshaw, C Brough

The Merensky Reef at Northam Platinum Mine in South Africa is characterised by a high degree of variability with respect to reef elevation (difficult to mine), as well as mineralogy and texture (difficult to process). Development along strike and down dip of multiple reef types has led to unpredictable run-of-mine characteristics that pose problems for the mineral processing circuit at Northam. Following mining terminology, Normal, Transitional (NP2) and Pothole (P2) Merensky reef types can be defined, and this geometallurgical study aims to characterise and understand the relationship between their mineralogical characteristics and laboratory scale batch flotation performance. The plagioclase-rich NP2 reef ore is the easiest ore to process in terms of capacity for high mill throughput as well as flotation performance. The lack of very fine-grained disseminated sulfide textures in the NP2 reef ore results in better liberation characteristics relative to the Normal and P2 reef types. Consequently, chalcopyrite, pentlandite and sulfide recoveries are highest for the NP2 reef ore. The lack of ferromagnesian minerals in the NP2 reef ore also results in the recovery of the least amount of floatable gangue during flotation tests. The Normal and P2 reef ores are similar to each other, with an orthopyroxene-rich mineralogy with associated alteration minerals. The P2 reef is also characterised by the highest sulfide content and degree of pentlandite liberation. Chalcopyrite, pentlandite and pyrrhotite liberation is only significantly increased by a change in grind for the Normal reef ore. The change in grind, however, only significantly affects pentlandite flotation performance and overall froth stability for the Normal reef ore. However, for all three ores, a small change in grind has a detrimental effect on pentlandite flotation performance.

Jan 1, 2008

By R Gaze, J Horton

Block models generated with all linear interpolation algorithms contain inherent smoothing that typically results in an underestimation of grades and overestimation of tonnes in resource estimates. For mineral deposits that are anticipated to be exploited by underground mining methods excessive smoothing may result in materially misleading estimates of Ore Reserves. To account for smoothing in the open pit mining environment recoverable reserve techniques such as indicator kriging and uniform conditioning are employed to provide non-spatially located proportions of the large blocks above the cut-off grade. These models are not suitable for underground mine planning where the actual location of material above cut-off is required to design its extraction. To correct for excessive smoothing it is proposed to modify the ordinary kriged block estimates a posteriori using an affine correction with a local variance adjustment factor. The proposed methodology is demonstrated for a base metal deposit during a feasibility study.

Jan 1, 2009

By Robertson GE, McLaughlin JD

An extensive laboratory campaign was conducted to find a suitable water soluble collector to replace diphenylguanidine (DPG) in the matte separation process. The examination of the collectors was done by measuring the rate of flotation and the best candidate collectors were selected on the basis of the rate parameters. As a result of this search mercaptobenzothiazole (MBT) was selected for a plant trial. A plant trial of two weeks duration confirmed that MBT will produce separations at least as good as those obtained with DPG.

Jan 1, 1993

By Morris A. E

The thermodynamically-based pyrometallurgical simulation software STEPSOL (Version 3.0) provides for the modelling of activities using the Interaction Parameter Model, the Regular Solution Model, the Sub-Regular Three Suffix Margules Model, the Sub-Regular Four Suffix Margules Model and various simpler polynomial models. These are briefly reviewed, along with the major sources of data available in the literature, and the implementation of the models in the program.

Jan 1, 1991

The education system today is turning out potential Mine Managers and Superintendents for the coal industry who are lacking in adequate management knowledge. They are required by the Mining Act to be highly skilled operators who are operations and production oriented. This puts them in much the same category as airline pilots and ships' captains. The real need is for them to be management and profit orientated. Changes over the years in Managers' and Superintendents' roles are highlighted by identifying those professions and vocations with whom they must now work. Comparing classifications in the 1916 award and the current award, and making a comparison between management and mining degree courses, leads to the conclusion that separate degree courses are necessary for future Mine Managers and Mining Engineers. Mine management must become a profession in its own right if optimum profits are to be made from mining in the future.

Jan 1, 1980

By O J. Restrepo Baena, S Nowosad, R Webber-Youngman, N Mojtabai, P Foster, A Binder, S Hazuria, erson, S Raval, L Liu

As the mining industry faces times of change, new challenges arise to ensure raw material supply for the younger and future generations. Different scenarios are currently shaping the way we mine and teach mining engineering. Led by an increasing demand for raw materials, net zero requirements for improving long-term operation performance, technological advancements such as automation and digitalisation, safety improvements, environmental considerations and a need for social acceptance, mining is pursuing to change and adapt to these requirements at a faster pace. Such changing times raise new concerns, one of the most relevant is the lower number of students interested or enrolling in mining engineering and related fields leaving mining engineering as one of the less preferred career options between the younger generations. Nonetheless, it is essential to continue addressing and supplying the skill sets that is suited to contemporary and future of the mining industry. To this end, globally, academia is currently undergoing several initiatives such as curricula updates and adaptation, up skilling, improving teaching practices and techniques, including e-learning techniques, enhancing industry-academia and inter-university collaboration, and much more

Sep 1, 2024

By S K. Panda, M A. Van Ende, S Chatterjee

Tata Steel Netherlands (TSN) aims to reduce its CO2 emissions by 35–40 per cent by 2030 and become CO2 neutral by 2045. A first step to reach these targets is via the utilisation of an Electric Arc Furnace (EAF), which will run on a mixture of high proportion of Direct Reduced Iron (DRI) and scrap. For an EAF operation, optimisation of slag chemistry is important to achieve the right mix of basicity (for refining especially dephosphorisation), foaming, volume (rate) and refractory life. Slag composition and rate can vary widely depending on the process variables like charge mix, charge composition, feeding rate, oxygen lancing, external carbon injection/addition, fluxing and refractory erosion/corrosion. Moreover, it is important to note that the slag composition and rate are ‘transient’ parameters and change throughout the heat. This makes all the dependent phenomena and/or outcomes transient as well. To describe all these effects simultaneously and be able to realistically simulate the EAF operations, a validated dynamic process model is important in the absence of real plant data. In this study, a validated dynamic EAF process model based on the concept of Effective Equilibrium Reaction Zone (EERZ) has been utilised to analyse the impact of high DRI industrial scale EAF operations on the transient slag characteristics – including slag volume (rate), composition, phases, solid fraction and viscosity. Simultaneously, the model is able to predict the impact on steel and offgas characteristics. Case studies were performed with 70 per cent DRI:30 per cent scrap mix considering both low and high-grade DRI. Both melting and refining aspects of the process including continuous feeding, arcing program, carbon addition, fluxing and oxy-lancing were considered.

Jun 19, 2024

By Morris A. E

The thermodynamically-based pyrometallurgical simulation software STEPSOL (Version 3.0) provides for the modelling of activities using the Interaction Parameter Model, the Regular Solution Model, the Sub-Regular Three Suffix Margules Model, the Sub-Regular Four Suffix Margules Model and various simpler polynomial models. These are briefly reviewed, along with the major sources of data available in the literature, and the implementation of the models in the program.

Jan 1, 1992

By S Meffre, A E. Fallick, K Zaw, I T. Graham, G Giuliani

Dispersed gem corundum is mined from placers, commonly from basalt fields, as occurs along eastern Australian and Asian continental margins. New laser ablation inductively coupled plasma mass spectrometry analysis (LA-ICP-MS) of Australian corundum allows genetic distinctions among these suites and gives clues to their primary lithospheric sources prior to basaltic delivery. Bimodal corundum suites at Barrington Tops, Cudgegong-Gulgong-Macquarie River and Yarrowitch, New South Wales (NSW), include lower Ga, higher Mg æmetamorphicÆ and higher Ga, lower Mg æmagmaticÆ groups. The Barrington Tops æmetamorphicÆ corundum is more Fe-rich (av 4500 - 7100 ppm) than Cudgegong- Macquarie River equivalents (av Fe 1800 - 2100 ppm). Yarrowitch corundum is relatively low in Fe, Ti and Cr. Along with other eastern Australian data (north-east Tasmania; New England, NSW) and from gem fields elsewhere, the combined trace element and O isotope data, reveal considerable geographic and genetic variations within the corundum suites. A few corundum groups contain noticeable Be, Sn, Ta, Nb, a particular genetic message that also precludes easy distinction of treated corundum in the gem trade. Expanding geochemical, inclusion and geochronological data on gem corundum hold promise for characterising derivative gem corundum on both geographic and genetic features.

Jan 1, 2008

By Thatcher R

In areas where undeveloped land represents a scarce resource, an upgraded post mining land use can result in economic benefits to both the mining company and to the community. A study undertaken at Allied Queensland Coalfields Ltd's Aberdare Colliery located between Brisbane and Ipswich during 1986/1987, assessed the costs and benefits of developing the site following mining for grazing, forestry and residential uses. The proposed final land use plan comprised a combination of these uses which can be upgraded to higher valued uses once subsidence monitoring of backfilled opencut areas and dumps indicates that total settlement has reached acceptable levels. The study involved the documentation of existing site environmental parameters and the delineation of site opportunities and constraints. The unpredictable nature of settlement over backfilled opencuts and overburden dumps represents the major constraint to urban development on mined areas.

Jan 1, 1987

By Kuzugundenli OE, Nagaraj DR

Organic complexing agents have received special attention over the past few decades in the search for reagents for improved flotation separation of minerals, especially non-sulphides. The majority of such reagents that have been proposed over the past few decades have remained largely a laboratory curiosity, except perhaps alkyl hydroxamates, because their selection is seldom based on commercial viability. In this regard, the choice of complexing agents such as oximes may be more realistic because of their widespread use in solvent extraction of copper. Our earlier studies have confirmed that they are also effective as collectors for copper oxide minerals, including chrysocolla which is the most difficult copper mineral to beneficiate. The flotation behaviour of chrysocolla for several structurally-related hydroxyoximes were studied as a function of pH and oxime concentration and the role of structural features examined. The structural changes studied included substitutions in both chelating and non-chelating parts of the molecule. The results indicated that, contrary to expectations, many of the structural changes in the basic molecule, salicylaldoxime, do not have a positive effect on collector efficiency. The reduction in collector efficiency is rationalised on the basis of possible steric factors affecting complexation and packing of the collector species on the mineral surface as well as effects due to changes in electron density brought about by substituents. Introduction of alkyl substituents on the oximic carbon of salicylaldoxime yielded the highest collector efficiency.

Jan 1, 1993