Search Documents

By Smith J. W, Hart G. N

Compositional and isotopic analyses of coal seam gases in the Southern Coalfields have shown that these gases frequently contain abnormally high concentrations of magmatically derived carbon dioxide. The size of this carbon dioxide reservoir and the extent of permeation of the sediments by carbon dioxide are not known.Therefore caution in evaluating the natural gas potential of the region is advised.

Jan 1, 1981

By Dorricott M. G

Ballarat Goldfields NL is developing an exploration decline at Ballarat East using a Mitsui Miike S-125 roadheader. To-date, 530 in of advance has been achieved at an average rate of 16.1 m/week. Roadheader availability has averaged 94.3 per cent, and pick consumption has averaged 0.016 per m. Ground support has involved pattern rockbolting with split sets, 100 mm thick fibre reinforced shotcrete, and steel sets as required. The slower than expected advance rate has mainly been due to difficult ground conditions. It is expected that a further 970 in of decline will be mechanically excavated before a drill and blast system becomes more economical.

Jan 1, 1995

Government established and financed the NZ Steel Investigating Co in 1960. Its investigations showed that a steel industry was feasible and desirable based uponNorth Island titanomagnetite ironsands, and charted a route for its establishment. The initial processing used post-1945 preheating and prereduction developments, but later innovative improvements created what was essentially a new New Zealand technology. Of the North Island titanomagnetite deposits: the small ones at Waipipi were best made available for export; those at Kawhia and Taharoa were too remote for the economic siting of a mill; that at Raglan proved too small; while at Waikato North Head three times the requirement of 50 million tons of concentrate were located in two sand areas averaging 18 per cent titanomagnetite. Economic studies showed that a South Auckland site would be ideal, close to New Zealand's biggest market. The mill site, on a basalt flow at Glenbrook, was located by a half-day's fieldwork - near both the Waikato North Head deposit, and a railhead for bringing in Waikato coal, etc, and taking out steel products.   This development was one of several since World War II which altered significantly the lives and homes of New Zealanders (others were natural gas, oil, geothermal power, epithermal gold, aluminium, opencastable lignite, etc). All had the essential ingredients of the highest government backing, direct or indirect government finance, and first-class New Zealand scientific and engineering skills (eg to create new technologies). Not one such project failed.

Jan 1, 1993

The Warraua and Mount Poole Inliers form part of a discontinuous series of basement complexes in the northwestern corner of New South Wales. The Inliers comprise mainly clastic sediments of low metamorphic grade (Wonominta Beds) and minor sills, dykes and intrusives, particularly within the Mount Poole lnJier. The Warratta rnlier has received attention due to the occurrence of auriferous quartz-veins where reef mining activities havetaken place.The deformational history of the Warratta and Mount Poole Inljers is characterised by a continuous subhorizontally WSW-ENE directed compression. Deformation was associated with the development of NNW-trending and steeply west-dipping major faults, which bound or biscct the inliers. Chevron folds and a penetrative axial planar cleavage characterise the deformational architecture and document crustal shorterung of at least 40 per cent. In zones adjacent to the major faults and within pelitic and semi-pelitic uruts, a multiple deformational evolution becomes apparent, comprising two events (D1 and D2). Deformational structures considered significant in this study were the result of D1. Tight, northeast-vergent fold patterns FI' and associated axjal plane cleavage SI' and reverse dip-slip movements at major faults indicate early northeast-directed thrusting during D1. This was followed by dextral strike-slip deformation displayed by tight, recumbent folds, en-echelon fold patterns (F2'), a northeast trending crenulation cleavage (52'), and two sets of second order faults, the latter showing high angular relationship to the major faults. A final stage of the deformational history (D2) is represented by WSW-ENE trending kink folds (F2).Auriferous quartz veins, predominantly occurring within pelitic and semi-pelitic units, were generated syntectorucally during the early deformational event (D1) in the course of commencing development of cleavage (S2'). Vein textures point towards vein formation by repeated hydrauJjc fracturing and fracture healing (crack-seal process), and by simple accretionary vein growth. Folded pelite-dominated horizons, considered as low permeability units, are suggested preferential sites where migrating metamorphic Ouids pooled and were trapped, causing high fluid pressure.Hydraulic fracturing and vein precipitation was controlled by lithology and structural constraints such as cleavage.K-Ar dates of approximately 440 Ma (Benambran Orogeny) marking the peak of metamorphism, and coinciding with the development of cleavage S1', also indicate the time of auriferous quartz-vein formation. A period of deformation of at least 30 Ma is proposed for the development of cleavage S1', as constrained by K-Ar dating and the intrusion of a syntectonic granitoid, the Tibooburra Granodiorite.

Jan 1, 1992

The planned extraction of deeper copper ore at Isa Mine has necessitated a review of existing equipment and methods to contain costs and improve working conditions. Mining is in progress for a crushing-conveying system to serve the deeper southern areas of the 1100 Orebody. This system will permit direct tipping of ore to the crushers and conveying of the crushed ore by cable belt conveyor to existing shaft loading facilities, a distance of about 2 km. To develop part of the conveyor drive a new machine will be used, the Robbins MM120 Mobile Miner, a joint development project between The Robbins Company and Mount Isa Mines Limited. The Mobile Miner uses a rotating cutting wheel to excavate headings 3.7 m high and from 4.7 m to 7.5 m wide. To ventilate the deep crusher complexes and associated development at high virgin rock temperatures, a refrigeration plant will be built on surface to reticulate chilled water underground. Bulk cooling of air to the 3000/3500 Orebodies and the southern crushers will be combined with the reticulation of chilled service water to the lower workings of the mine.

Jan 1, 1984

Near Kangiara in south eastern New South Wales, Australia, a number of polymetallic (copper, lead and zinc, with minor silver and gold) mineral deposits occur within a relatively broad volcanic rock belt, intercalated with limestones, sandstones and shales, of Silurian age. The Kangiara deposit was the most significant for the region.Adjacent to the Kangiara deposit, the unaltered country rocks are more rhyolitic than elsewhere in the volcanic rock belt, and the mineralization is accompanied by silicification, chloritization, sericitization and argillization. The host rocks typically contain a higher K20:Na2O ratio than the volcanic rocks not associated with mineralization.In the Kangiara deposit the mineralization consist of massive (in part banded), fragmental, disseminated and vein-type copper-lead-zinc ores, with the massive and fragmental types divisible into pyrite-rich, chalcopyrite-rich and sphalerite-galena-rich varieties. With respect to this mineralogy, the ore textures and sulphur isotope compositions the deposit can be compared to the stratiform mineralization associated with Silurian acid volcanic rocks at Woodlawn, Captains Flat and elsewhere in the Lachlan Fold Belt, as well as the Tertiary Kuroko deposits of Japan.

Jan 1, 1990

By S L. Simpson, J Waworuntu, B M. Angel

"The Batu Hijau copper/gold mine, operated by PT Newmont Nusa Tenggara, is located in the south-western part of Sumbawa Island, Indonesia, and is situated ~10 km from the south coast at an altitude of ~450 m above sea level. The mine became fully operational by year 2000 and processes approximately 120 000 t of ore per day that contain an average of 0.53 per cent copper and 0.4 per tonne (g/t) gold. Tailings management at the mine includes a deep-sea tailings placement (DSTP) system that discharges tailings through a pipeline via an outfall located at a depth of 125 m at the head of the submarine Senunu Canyon (Figure 1).The environmental impact assessment undertaken prior to approval of the DSTP evaluated both on-land tailings storage facility (TSF) and DSTP options for tailings management. Negative attributes of the on-land TSF included removal of approximately 2300 ha of forest/agricultural land, the potential relocation of >2000 people from their communities, the high average annual rainfall (>2500 mm) and potential for earthquakes presenting challenges for water management and creating a long-term risk of failure. The final choice and Indonesian Government’s approval of DSTP was also influenced by the close proximity of the deep submarine canyon to the mine. The Batu Hijau mine is one of the larger examples of DSTP in the world and deposits tailings at the greatest depth. The depth of the main canyon increases to >2000 m within 20 km of the coast, and to >3000 m approximately 50 km from the coast.The DTSP at Batu Hijau must comply with an environment management plan (EMP) and environment monitoring plan of permit stipulation that approved its commencement in 2000; updated in 2010 and 2015. The environmental management objectives were to avoid impacts to highly productive components of the ecosystem such as coral reefs, mangroves, surface waters and fisheries, and confinement of impacts to areas of low biological productivity. In the vicinity of the DSTP outfall and within the Senunu Canyon, the management plan predicted significant adverse impacts from the DSTP on the marine ecosystem in the form of: reduction in sea water quality due to elevated turbidity and dissolved copper concentrations burial of benthic organisms a reduced habitat for demersal fish.Recovery of the pelagic and benthic ecosystem to preoperating conditions was predicted to occur within the first two years after operations cease. The CSIRO has performed due diligence studies to independently verify compliance with permits and evaluate new monitoring objectives (Apte et al, 2004; Simpson et al, 2010; Angel et al, 2015), and has performed assessments of environmental monitoring data on the tailings footprint and ore stockpile processing against the above environmental objectives (Simpson and Angel, 2015).CITATION:Angel, B M, Simpson, S L and Waworuntu, J, 2016. Long-term monitoring and targeted assessments to improve management of mine wastes – the Batu Hijau project, in Proceedings Life-of-Mine 2016 Conference, pp 81–84 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Jun 28, 2016

By H Austrheim, A K. Engvik, A Putnis

How aqueous fluids move through rocks and minerals is a question of possible pathways and mechanisms. Existing pathways such as fractures and grain or mineral boundaries provide obvious channels for fluid movement. We show how minerals reactive in the presence of an interfacial fluid can be replaced by new product phases through a process of interface-coupled dissolution-reprecipitation. A resulting porosity in the new phase provides a new pathway for fluid movement and therefore mass transport through the mineral, which progressively reacts at a moving interface. Eventually fluids of new and changing composition can pass through originally solid minerals and move on further, taking remobilised elements with them, to be reprecipitated whenever the chemical and/or physical conditions allow. One such example is albitisation of rocks associated with mineralisation.

Jan 1, 2008

By L Kempenaers, T van der Maten, U König, M G. C Zoontjes

Improving liquid blending operations in production plants is of paramount importance in many industries like mining, oils, petrochemicals and food. For accurate blending of different types of process streams, like homogeneous, heterogeneous, cold or hot streams, it is essential that the composition can be accurately monitored in real time. Advances in energy dispersive X-ray fluorescence (EDXRF) technology offers the possibility to apply XRF for online elemental analysis. In this paper we discuss an online EDXRF analyser for accurate blending control in many industries.EDXRF has the advantage that multiple elements can be measured simultaneously over a wide concentration range of wt per cent down to a few mg/kg, for elements between sodium (Na) and americium (Am) in the periodic table. To reach the desired accuracy and precision in an online XRF analyser, it is important to bring a representative and homogeneous sample of the process flow into the optical path of the analyser. The combination of a laminar flow cell design and advanced EDXRF technology leads to low detection limits and high performance. The obtained precision and accuracy allows for much tighter process control. In this paper we present two examples of industrial applications.CITATION:Zoontjes, M G C, van der Maten, T, Kempenaers, L and König, U, 2017. Online X-ray fluorescence spectrometer for accurate monitoring and improving blending sharpness in liquid production processes, in Proceedings Eighth World Conference on Sampling and Blending , pp 235–238 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

The issue of fine coal and tailings dewatering has become of increasing concern to many coal preparation operators, both in Australia and overseas due to a variety of factors. Increasing mechanisation and mining of thinner seams over the past decades has resulted in an increasing amount of fines generation while increasing international trade in coal and tighter environmental constraints on tailings disposal have resulted in the production of these same fines to be an increasing problem. However, technology to date has not always been able to supply a cost-effective solution to the handling of these fines in an efficient and environmentally benign manner. This paper will review the key issues associated with the dewatering of fine coal and tailings, will describe the major current practices and constraints, and finally will indicate alternative technologies that may have to be considered in the near future. For the purpose of this paper, "fine" coal is described as that material less than 0.5 mm in diameter (as this is the most common cutpoint between various plant circuits in Australian practice), although the technological constraints are very much dependent upon the fraction less than 45 micron. The amount of minus 0.5 mm material fed to plants varies, depending upon the type of coal and mining operation, but in Australia may range from less than ten per cent to greater than 30 per cent of the feed in higher rank coals.

Jan 1, 1991

By T D. H McGrath, O Baker, W P. Staunton, C Ypelaan

"The carbon-in-pulp process has been used extensively in the gold industry since the late 1970s to recovery leached gold from solution. Despite more than 30 years of experience in operating carbon circuits, average gold solution loss has remained at an average of 0.02–0.03 ppm (mg/L), higher than the ‘best practice’ target of 0.01 ppm.Process modelling, such as SIMCIL developed by the Curtin Gold Technology Group (GTG), can provide information on optimum set points; however, manual control of the circuit limits the potential benefits.An automated carbon measurement device, the Scout Carbon Meter, has been developed to allow for automation of carbon concentration measurement, and automated control of the carbon transfer pumps. This paper describes the results from the evaluation of the first two prototypes of the meter.Citation:Staunton, W P, McGrath, T D H, Ypelaan, C, Baker, O and Eksteen, J J, 2016. Optimising Carbon Management - Increasing Gold Recovery and Decreasing Costs with the Carbon Scout, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 225–228 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

Concrete has been used for many years in block caving, principally for drift and drawpoint linings. This paper describes the requirements for concrete in this application, the required properties, the mix design, and transportation and placement systems. In addition a concrete mix design rationale is also proposed.

Jan 1, 2000

'Industrial Minerals - their mining and use in New Zealand' is the theme of the 1978 Annual Conference of the New Zealand Branch of The Australasian Institute of Mining and Metallurgy. This paper describes the use of phosphate rock, sulphur and potassium chloride (potash) - three industrial minerals which have enabled the farmers of New Zealand to increase production to current levels. The growth of imports of these raw materials for the New Zealand fertiliser industry is well documented in NZ Fertiliser Statistics 1977. This is the most recent of the Ministry of Agriculture and Fisheries annual publications on this Subject prepared from the detailed returns of fertiliser manufacture and sales from each fertiliser works. There are now 12 of these works in New Zealand one of the most recently established being in Whangarie where this conference is being held. Its capacity to manufacture superphosphate will shortly be 300 000 tonnes twice that when it opened late in 1964. New grinding and manufacturing equipment comes on stream early in 1979. This paper illustrates the interdependence of two primary industries, agriculture and mining. New Zealand's economy in the foreseeable future will be based on agriculture so that our standard of living is dependent on the overseas prices and freight costs of the bulk raw materials from which our fertilisers are made. For the year ended 31 March 1978 New Zealand's total exports were $3395 million, of this total $2413 million (71%) came from the products of pastoral agriculture (wheat, wool, dairy and other animal products), $291 million from forest products and $501 (15%) from manufactured exports. Approximately half of the pastoral receipts can be attributed to the fertilisers applied at a total cost of about $200 million including subsidy.

Jan 1, 1978

By D Cliff

Despite advances in technology, the Australian underground coal mining industry continues to have incidents involving spontaneous combustion. Managing these incidents relies heavily on understanding the state of the event as it develops and controls are applied. Gas analysis plays a major role in aiding this interpretation. This interpretation is based upon laboratory testing of coal samples under conditions very different to those found in an underground coal mine. This paper will explore the links between laboratory data and actual events. It will highlight the difficulties of using laboratory data. It will outline the relevance of laboratory data and how it can be usefully applied to manage spontaneous combustion events as well as in establishing relevant trigger action response plans to facilitate early detection and control of such events. The paper will identify some of the factors that need to be applied when adapting laboratory data to apply to the underground coal mine. It will outline the need for comprehensive knowledge of the local conditions and gas concentrations to be expected at all locations in an underground coal mine. Further, it will demonstrate the need for mine environment monitoring to go beyond simply measuring gas concentrations but also to include reliable atmospheric pressure, temperature and air velocity monitoring.CITATION:Cliff, D, 2013. Gas analysis - Linking the laboratory with reality, in Proceedings The Australian Mine Ventilation Conference , pp 277-282 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By M Olsson, I Bergqvist

A Swedish table of blast damage depths has, in one form or other, been in use since the late-1970s. Its history and the underlying theory are described. New experimental and theoretical findings that point out a number of shortcomings in the table and the underlying theory are presented and discussed. A revised version of the blast damage table was recently introduced in conjunction with new but incomplete recommendations for cautious perimeter blasting. The new table leaves the difficult task of taking into account factors like decoupling, water in the borehole, the rock properties, type of initiation, charge length and the actual bit diameter to the user. This paper discusses different ways of doing this, based on the experimental findings and a recent formula for the prediction of the lengths of radial cracks behind the half-casts. The material presented in this paper is meant to supplement and extend the new Swedish recommendations for cautious perimeter blasting of tunnels, shafts, pits and road cuts.

Jan 1, 2001

By M Wortley, J Korteniemi, D La Rosa, L Rajavuori

Geometallurgical modelling of an orebody provides benefits to a mine by gaining a better understanding of the ore characteristics and how they affect the performance of the concentrator. With this knowledge, plant operating conditions can be adjusted to optimise throughput and recovery in advance of the arrival of particular ore types. Therefore, it is extremely important that the origin of the ore being processed is known as accurately as possible. Depending on the homogeneity of the ore characteristics, reliance on assumptions about stockpile residence times, scheduling and material handling can render the best geometallurgical models useless.The solution adopted at Agnico Eagle’s Kittilä mine was to utilise Metso SmartTags™ and in-house expertise to develop a system that continuously and accurately links geotechnical and lab data from the mine to the performance of the plant. This application presented several unique opportunities and challenges. For example, this was the first installation of a SmartTag™ system for geometallurgical modelling in an underground mine. Challenges included the fact that the system installation is routinely subjected to temperatures below -20°C.The system was installed and commissioned in early 2013 and has been operating continuously since. Kittilä has begun to see the benefits of the system, with an increased understanding of how different ores are processed in the concentrator. Other advantages include the ability to alert operators about the arrival of difficult ores and a better understanding of the ore handling systems.This paper describes the installation and use of the system at Kittilä and details some of the geometallurgical relationships that have been developed using the data collected so far.CITATION:La Rosa, D, Rajavuori, L, Korteniemi, J and Wortley, M, 2014. Geometallurgical modelling and ore tracking at Kittilä Mine, in Proceedings Orebody Modelling and Strategic Mine Planning Symposium 2014 , pp 291–298 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 24, 2014

By Hannan JC

Consent to develop and operate a new coal mine in New South Wales (NSW) will be conditional upon a number of environmental controls. In NSW, applications for any new major development associated with coal mining are determined by the Minister for Planning and Environment. The environ- mental conditions placed on the development consent, the coal mining lease and the approvals, and licences under the pollution control legislation amount to a substantial component of any new project's commissioning considerations. The nature, scale and location of projects and the principles of pollution control on which conditions of State Pollution Control Commission (SPCC) approvals are based have a considerable influence on project planning. The design, construction and operation of coal mines in NSW has been progressively modified over the past 15 years, to incorporate increasingly stringent requirements for environmental management. These requirements are in turn, a reflection of a greater community demand for environmental protection.

Jan 1, 1986

Giving the keynote address in the final session of a conference dealing with closely related topics has a disadvantage in that much of what can be said has been said. It also has an advantage, however, because it presents the speaker with the opportunity to integrate and analyse the material presented by the various speakers. I would like to look to the near future in Aust- ralia and the United States of America, to the risks, problem areas, and changes of a rapidly evolving post-industrial era-an era we are begin- ning to experience where industry no longer `calls the tune'. We miners have been quick to point out and emphasize, that ours is a `high-risk' industry in the world of business and commerce. Yet, clearly those who have survived, and been successful, have learned to anticipate and cope with risk and change. This ability has been a distinguishing feature of the industry's leaders who, in market studies and commodity selection, exploration and development, mine planning, metallurgical pro- cessing, and general administration and operation 1. identify areas of risk or inevitable change, 2. analyse, test and quantify those factors of risk or change, and 3. design methods, systems, equipment to elim- inate, moderate, or control or economically compensate for predicted risks or changes.

Jan 1, 1978

By Salmon P. T, Gilmour R

Commercial production of zinc started at the Pasminco Metals - EZ Plant, Hobart, Tasmania, in 1921. Since that time the capacity of the plant has been steadily increased to its present level of almost 220 000 tpa. Major areas of the plant have been successively upgraded over a number of years, (Roasters, 1969, 1975; Acid Plants, 1981; Casting, 1972; Residue Treatment Plant, 1971), but, until recently, the leach/purification area remained virtually unchanged from the time the plant was built. The major redevelopment of the hydrometallurgical plant began with fully integrated pilot plant testing of the proposed new circuit in 1981. The pilot plant incorporated the Low-contaminant Jarosite Process, and a new two-stage zinc dust purification procedure. In 1985, approval was granted for a major modemisation program which involved the complete replacement of most of the leaching and purification plants, and substantial improvements to the residue treatment plant. Construction of the first of the new plant sections, Strong Acid Leaching, commenced in 1986. This paper describes briefly the modernisation program itself, and the current method of zinc production at the PMEZ plant. The new plant sections comprise a Strong Acid Leach stage to improve lead residue grade; a Preneutralisation stage to reduce metal losses in jarosite; new filtration stages for both jarosite and lead residue; new Neutral Leach and Weak Acid Leach stages to replace old equipment; a new Solution Purification stage to replace the use of organic reagents to remove cobalt; and a new Gypsum Removal stage to cool the solution before electrolysis. At the completion of the modernisation program, only the electrolytic cellhouse remains of the early plant sections.

Jan 1, 1993

The theme at this yearÆs AusIMM New Leaders Conference in Ballarat was æThe Minerals Industry û Future Directions for New LeadersÆ. There was a strong focus on the recruitment and retention of trained and skilled graduates and new professionals into the mining profession. This paper highlights some of the key findings and discussion points from the New Leaders Conference. While some of the main causes of the decline in attracting new geoscientists to the mining industry have been identified, there still remains a lack of accountability among a number of Australian mining companies. Some of the factors identified that are driving new graduates away from the industry include; the social and geographical isolation, the long hours in challenging conditions and a difficulty in obtaining work straight out of University. Often there appears to be no clear opportunities within companies for career development and advancement. The opinion also still persists that the mining industry is lagging behind in both environmental and technical developments, which makes entry to the industry unattractive. Solutions that some of the large players in the Australian mining industry are implementing to help reverse the trend include targeted marketing of the lifestyle, money, freedom and travel offered in the mining industry, the development of graduate recruitment programmes and much more emphasis on the quality and reputation of the companies themselves. Incentives to attract families have also been significant in attracting and retaining employees whom otherwise would have left the workforce. However, more still needs to be done to completely reverse this trend and the mining industry needs to continue to be proactive in marketing itself as a desirable employer and career choice option for students and new professionals.

Jan 1, 2004