Search Documents

By D Caffrey

To demonstrate the advantages of using electronic delay detonators over pyrotechnic detonators, a trial using the DNES Dynatronic System was conducted at the KCGM Mount Charlotte operation in 1998. The trial clearly demonstrated that accurate control over the firing delay time between blastholes can lead to fragmentation improvement and ground vibration energy control which are two important issues for the Mt Charlotte underground operation. Excellent fragmentation was achieved by employing a 12 ms delay sequence. Detailed fragmentation analysis has shown a 10 to 20 per cent passing increase for the rock fragment size from 0.1 to 0.4 m compared with the pyrotechnic detonator firing. There was no increase in ground vibration level on the surface with the electronic detonator firing even though the electronic detonator firing had a much shorter blast duration than the pyrotechnic detonator firing. In fact, our energy calculation has clearly shown that much less energy had been propagated to the surface from the blast using electronic detonator firing.

Jan 1, 1999

During the first five years of operation, the Lihir gold mine has steadily increased plant throughput rate to over 4 Mtpa, well above the original design capacity of 2.8 Mtpa. Understanding how future variations in ore type impact on plant performance has been an integral part of LihirÆs development program. This paper discusses the key drivers for significant improvements to the plant, including a second oxygen plant, a pilot flotation plant, an autoclave heat recovery circuit, a pebble crushing circuit and additional autoclave feed pumping capacity. The result is a process plant with the flexibility to accommodate variations in ore type without significant loss of throughput.

Jan 1, 2003

By A F. von Wielligh, M Scott, L Keeney

Operational Grade Engineering (GE) is the early (pre-processing) discard of low-grade mineralised and/or barren rock to improve the ore grade and/or reduce deleterious elements within the run of mine ore to be processed. GE activities generally have an impact on primary and ancillary mining activities, equipment utilization and overall equipment productivity. By discarding material which would have reported as ore (in a non-GE mine plan) means that GE must increases the total ore and total rock mining rate requirements to sustain mill feed targets. One challenge of GE and the planning of GE activities is that there are several indirect parameters which impact operational productivity. Modelling these potential impacts and determining if they can be overcome with alternate mine sequences, equipment application or possibly a different equipment fleet altogether is a key question requiring investigation. Overcoming these potential productivity obstacles associated with a more complex operation by introducing new operational parameters and destinations for ore and possibly sub-grade blocks, requires a GE mine plan that is coupled with detailed equipment productivity metrics and a sound operational plan incorporating all GE infrastructure requirements. Several GE mine plans and equipment productivity models indicate that mining rates generally need to increase by approximately 5% to 15% to sustain mill targets and often negatively impact equipment unit productivity metrices through increased cycle times, additional queuing and destination changes. These changes to productivity metrics are however offset by step change increases in asset value. This paper details a methodology to develop GE mine plans that incorporate equipment modelling, flexible mine sequencing and equipment-based production scheduling. In addition, the paper will outline impacts of GE planning on equipment unit productivities through worked examples and models.

Nov 10, 2020

By M Gabbitus, B Young, T Lukins, M Slater

This paper details the implementation of a new type of grade control system at the Black Star open cut mine in Mount Isa, Queensland. It explores the site requirements for grade control, what as previously in place and what the site required moving forward. It also details some of the features of the system installed and why it was chosen over other grade control systems available. Black Star open cut mine has been in operation since late 2004, and was developed to extract the surface extents of the Ag-Pb-Zn mineralisation previously mined in the Isa Lead Mine. Black Star is currently mining seven distinct orebodies in and around active void hazard zones and hence, its grade control requirements are very detailed and complex. The implementation of a new system to manage the model update and block out processes was, therefore, of critical importance to the site and required a detailed understanding of the requirements of the entire mining team from drilling through to geology, survey and production. Having previously run the grade control process using site specific æblack boxÆ scripts and macros, Black Star needed to implement a more open, auditable and flexible system, which allowed the geologists to control the process and make strategic changes as the situation demanded. MineSightÆs Axis Grade Control, with its flexible, generic framework for managing the process, met these demands. Being an out of the box solution that requires minimal setup and training was also a key factor in the decision to use it.CITATION:Lukins, T, Slater, M, Gabbitus, M and Young, B, 2012. The introduction of axis at Black Star Open Cut, in Proceedings Eighth Open Pit OperatorsÆ Conference , pp 71-74 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 18, 2012

Solid Energy New Zealand Limited (æSolid EnergyÆ) is a state-owned coal mining company, producing 4.0 Mtpa from a number of opencast and underground mines in the Huntly, West Coast and Southland regions in New Zealand. The company currently exports 2.1 Mtpa of coking coal. Exports are expected to grow strongly over the next five year as the company expands production into new semi-soft and thermal coal reserves. Domestic coal demand is also expected to grow strongly, particularly in the North Island, as the Maui gas field reserves diminish, and thermal coal becomes more important for electricity generation and meeting the energy needs of forest processing and other industries. Solid Energy is expanding and developing its risk management practices across all areas of the business: strategic planning û extensive use of scenario analysis and probabilistic modelling over a 20 year period; investment decisions û development and application of a rigorous six stage æProject Assessment GuidelineÆ process for all new mine developments; geological and geotechnical risk assessment techniques û use of best practice techniques including seismic surveys; financial risk management û a dynamic approach to hedging based on effects based analysis of Cash Flow at Risk analysis against preset risk tolerances; risk financing û the use of a captive insurance subsidiary, and the experiences of a small coal company seeking to obtain insurance cover on a æhardÆ international insurance market; and integrated risk management û the challenges of trying to implement a broad integrated risk management approach across the company, that supports implementation of strategic objectives as well as meeting æcompliance or legislative basedÆ risk management requirements.

Jan 1, 2003

By A Liu, X Wang, W Peng, Q Zhang

Pulp rheology plays a critical role in fine mineral flotation. Yield stress and apparent viscosity are two important rheological parameters affecting mineral flotation recovery. In this paper, the concept of pulp rheology and its measuring method are presented. The main factors, such as particle size, pulp concentration, mineral types, pulp temperature, inorganic salts, that affect the pulp rheology are systematically reviewed, and then followed by the discussion of the relationship between pulp rheological properties and flotation performance. Generally, high pulp apparent viscosity and yield stress values have been found to have an adverse effect on flotation recovery. In addition, due to the hetero-coagulation between the valuable mineral and gangue mineral, the pulp of mixed ore shows higher viscosity than that of the single mineral slurry. This paper is expected to provide some references for the efficient upgrading of low-grade and complex ores from the perspective of pulp rheology.

Aug 24, 2022

Tumbling mills have been used in the minerals indusu) for occr WO years, with the design changing little, but the size of the individual pieces of equipment increasing significantly with the lowering of head grades, and the push for greater

Jan 1, 1997

By A Hughes, S G. Rosin

This paper presents the design and construction approach adopted for the widening and stabilisation of the existing decline tunnel forming part of the Scenic Railway Upgrade project at Katoomba in the Blue Mountains of New South Wales (NSW), Australia. The overall upgrade project included new trains and track, rebuilding of the top and bottom station and installation of a new winch and control system. All the works were undertaken over an eight-month period between August 2012 and April 2013 as part of a $30 M upgrade of the railway.The railway is the steepest cable-driven line in the world at a maximum of 52° extending over 350 m and descending from the escarpment into the Jamison Valley. The track was built in the 1880s for coal haulage and is recognised as a remarkable engineering achievement for its time. The tunnel section extends for about 120 m at the start of the decline and is about 3.5 m wide and 3.5 m high. The tunnel was excavated principally within medium to high strength Banks Wall sandstone and given that the widening only involved about 200 mm of trimming of the crown and sidewall this aspect of the work was not a critical support issue, except at the upslope portal. The tunnel crown however is entirely intersected by a major near vertical shear zone which presented significant challenges for the tunnel stabilisation works.Three-dimensional laser survey scanning was used for definition of the tunnel clearance envelope for the widening, and also to subdivide the tunnel into various geotechnical sections to assist in support design. Specifically oriented rock bolts extending beyond the shear zone into stable rock were used together with mesh, shotcrete and extensive strip drains and flushing points for drainage of the shear zone.Unique aspects of this project were included into the specifications and work methods. This included construction of a mobile working platform for tunnel works, the use of dry shotcrete application, difficult access for rock bolting and limiting vibration during the tunnel trimming works due to the risks associated with crown instability. The works also took into consideration particular safety constraints/work exclusion areas to address the risk of detachment of rock which could mobilise downslope to the track area below. This was required because other works were in progress such as micro-piling and bottom platform works which were being undertaken concurrently with the tunnel work.CITATION:Rosin, S G and Hughes, A, 2014. Scenic Railway Tunnel upgrade in the Blue Mountains, New South Wales – an approach to design and construction, in Proceedings 15th Australasian Tunnelling Conference 2014 , pp 607–618 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 17, 2014

By A Kleinitz, J Halilovic, K Trappitt

Mine operators use grade control to determine the destination of each block of material in the mine. In polymetallic mines, grades are best expressed in dollars: the Net Smelter Return, NSR, per tonne. To estimate NSRs, geologists working on grade control develop models for each geometallurgical domain in the mine. These models may incorporate observations on the mineralogy and grain sizes of the material being examined. The site’s mill operators contribute to the models by providing geologists with statistical analyses that relate assay results and mineralogical compositions to metallurgical parameters, such as the rates of recovery of each economic metal to each of the concentrates produced, and the compositions of those concentrates. The team responsible for sales and marketing of the site’s products contributes to the NSR models by providing details of the costs of shipping concentrates to smelters and refineries; and by providing figures that are specified in the smelter contracts, such as the payability of the metals in each concentrate and the fees charged by the smelter. The mill operators also provide, for the NSR models, equations to estimate the rates of recovery of deleterious materials to each concentrate. Deleterious materials comprise mostly halogens and amphoteric elements, both of which reduce the efficiency of smelters. Furthermore, deleterious materials such as antimony and arsenic may be poisonous to people and to the environment. The sales and marketing team provide specifics of the penalties that smelters impose upon deleterious materials. These penalties may reduce NSRs by tens of percent, possibly to levels below the cut-off grade. Thus, in the blocks that are subject to grade control, mine geologists monitor not only the concentrations of economic metals, but also the presence and abundance of deleterious materials. The preparation and maintenance of models, to estimate NSRs and to assess changes in the levels of potentially toxic materials to be mined, requires close and continuing consultation between corporate departments. There must be strong communication of mine geologists with the mill operators; with the people who market the mine’s concentrates; and, should there be a risk of encountering toxic levels of deleterious materials, with the mine’s health, safety and environmental officers. This co-operation could require radical changes in the structure of many organisations. However, experience suggests that such changes can significantly improve the profitability of a mine.

Mar 22, 2022

Diamond bearing deposits are extremely low grade and require large bulk samples to be tested to determine the grade and quality of the stones. The semi portable plants, for treatment of these bulk samples, have followed the development of commercial processes for diamond concentration. These processes included jigs and diamond pans, which have been largely supplanted by heavy media processes for primary concentration, due to the higher efficiencies in all size ranges. A number'of flowsheets including these processes are presented. The final recovery of diamonds from the bulk sample concentrates can be accomplished by rejigging, adherance to grease or by X-ray sorting. Flowsheets incorporating all the processes are presented. Two plants are described; one incorporating jigging, rejigging and hand sorting; the other using heavy media separation, and wet X-ray sorting.

Jan 1, 1984

By V Rasouli, G Cavanough, A Mokaramian

The sampling time, the costs and its quality are the three factors that determine the best method of drilling in mineral exploration. The two principal methods of reverse circulation (RC) and diamond core drilling are often used in combination by mine operators. RC is used for drilling shallow holes and in-pit grade control, and core drilling for deeper holes to identify future resources. The RC method is faster and more flexible than coring and provides virtually uncontaminated cuttings (ranges from dust to 25 mm chips) to the surface cyclone suitable for geochemical anomalies. The diamond coring produces core samples to increase the level of geological knowledge and the 3D extension and distribution of the orebody. However, both of these methods are subjected to certain limitations and inefficiencies in reaching deeper depths and drilling complex hole geometries. Examples of such shortcomings include the inability to provide enough air pressure for RC drilling and high friction between drill pipe and the hole wall in diamond core drilling.Considering that delivering large volume of reliable samples from deep zones to the surface in shortest possible time is of paramount importance in mineral exploration, and assuming that obtaining core samples over whole overburden is not always essential, then drilling small size holes as fast as possible and delivering the small chip samples to the surface would be a good alternative with several advantages over conventional drilling methods for deep hard rocks mineral exploration. As a result, the use of coiled tube (CT) drilling technology has been proposed recently for such applications. CT is a continuous length of ductile steel or composite tube stored and transported on a large reel; and allows fast drilling by eliminating the connection time and providing continuous circulation during drilling. This enables quick access to the zone of interest to collect the cuttings or obtain core samples. CT is advantageous particularly in drilling directional boreholes and multi-laterals. In this paper, feasibility of using CT delivering reliable samples is discussed for deep mineral exploration. In addition, recent developments and practices are presented that make CT a reliable drilling technology to drill cheaper, faster and deeper and to deliver more continuous and reliable data and samples from deep formations.CITATION:Mokaramian, A, Rasouli, V and Cavanough, G, 2012. Quality sampling using coiled tubing drilling in deep mineral exploration, in Proceedings Sampling 2012 , pp 73-80 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 21, 2012

By P D. Munro

"This is a reprise of the paper ‘Back to the Future – Why Change Doesn’t Necessarily Mean Progress’ presented to the Tenth Mill Operators’ Conference in 2009. It was observed that the ‘boom and bust’ cycles of the industry, together with trends in tertiary education and the effects of fly-in fly-out (FIFO) operations raised serious questions about the sustainability of human capital in the mineral processing sector.In 2016 we find ourselves in a ‘bust’ after enjoying a decade of the longest commodity price ‘boom’ in a century. In the ‘boom’ did we:make any technological breakthroughs?put measures in place to improve our human capital, especially in the area of ‘professional formation’?The paper makes observations on the current performance of mineral processing engineers and the organisational milieu in which they operate. It questions whether mineral processing engineers are actually ‘adding value’ at some sites given their organisational and operational practices.Some technical trends are examined and what it might mean for mineral processing engineers.Given the above and demographic trends for mineral industry professionals, changes to the seemingly current laissez-faire model of professional development are proposed.Citation:Munro, P D, 2016. Back to the Future - Still on the Dark Side, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 341–348 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016

By S Dorrington, J Olsen, N Kinkaid

Several studies have been conducted on the economic analysis of mining near-Earth asteroids for resources for use in Earth orbit. While these studies use detailed economic figures of merit, they often use many invalid assumptions in the trajectory design. Factors such as the energy and propellant requirements are estimated with analytic methods, however, the stay-time at the asteroid and the spacing of repeated launch opportunities are not taken into account. The work outlined in this paper attempts to combine detailed trajectory design methods with newly defined economic figures of merit to improve the economic assessment of asteroid mining missions. The study focuses on asteroid 2014 EK24, a near-Earth asteroid with very Earth-similar orbital properties.CITATION:Dorrington, S, Kinkaid, N and Olsen, J, 2015. Trajectory design and economic analysis of asteroid mining missions to asteroid 2014 EK24, in Proceedings Third International Future Mining Conference, pp 281–288 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

By R J. Romañach

The theory of sampling (TOS) is now followed in the development of near infrared (NIR) spectroscopic methods for the pharmaceutical industry. TOS has been the guiding light for a two-step approach for spectroscopic composite sampling available for the development of real-time analytical methods for particulate-based industrial processes. The two-step spectroscopic sample composite has been used in the development of process analytical technology (PAT), an important regulatory initiative to improve the quality of pharmaceutical products. The two-step sample composite approach overcomes the low sample volume analysed by PAT methods; one of the key limitations to PAT implementation in the industrial production of particulate-based materials.PAT methods need to be validated demonstrating their accuracy, precision, specificity and robustness. TOS provides a deeper understanding of these validation studies which involve discrete particulate material. The validation of PAT methods is now being performed considering both sampling and analytical errors, while practically all previous method validations only addressed the total analytical error (TAE) of these methods. This has been a crucial impediment for the field of chemometrics as well.PAT is a key element of continuous manufacturing (CM) processes, which are considered an emerging technology capable of increasing the flexibility, agility and robustness of pharmaceutical processes while reducing their costs. The outflow of the continuous process is a 1D lot, and variographic analysis has been shown to discern process variation from sampling and analytical errors in pharmaceutical CM processes. Thus, variographic analysis is a process improvement tool with significant potential for improving CM processes. The possibilities for improving pharmaceutical manufacturing are enormous.CITATION:Romañach, R J, 2017. Theory of Sampling – from missing link to key enabler for process analytical technology, in Proceedings Eighth World Conference on Sampling and Blending , pp 63–68 (The Australasian Institute of Mining and Metallurgy: Melbourne).

May 9, 2017

By A Hocking, S Henderson

Commonwealth of Australia (2016) defines rehabilitation as comprising “the design and construction of landforms as well as the establishment of sustainable ecosystems or alternative vegetation, depending upon the desired post-operational land use”. For open cut coal mines in Queensland and New South Wales, the question of how to apply this intent to pits at mine closure is repeated for hundreds of individual pits. In EISs, closure plans and public discussion, assorted treatments are proposed to rehabilitate pits. While some aspects of final voids have been intensively studied, there is little guidance on how to choose a final void treatment option that delivers the optimal outcome against rehabilitation goals. For example, in the Bowen Basin and Hunter Valley commonly proposed rehabilitation actions include reducing the angles of pit walls; however, with few voids successfully rehabilitated to date there is limited understanding of what different wall slopes will achieve.CITATION:Henderson, S and Hocking, A, 2018. A decision framework for comparison of coal void rehabilitation options, in Proceedings Life-of-Mine 2018, pp 127–130 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 25, 2018

By Hare S. M, Lumsdaine I, O&apos

Converter slag assaying 3.7 per cent Cu is produced by Mount Isa copper smelter at a rate of up to 180 000 tonnes per annum.Priority is given to the processing of ore, however concentrator capacity periodically exceeds that of the mine and the opportunity is taken to treat converter slag. It is processed in batch campaigns, typically through the Copper Concentrator, but the Hilton Concentrator has also been used. Slag and ore are kept as separate as possible, since each has an adverse effect on the flotation performance of the other.

Jan 1, 1993

By E Asakpo, S Chaffer, A Heath

Newmont has had continuous production at their Ahafo operations, Ghana, since 2006. In 2013, Ahafo initiated an efficiency programme to improve mill performance and reduce energy consumption. Following this assessment, a Turbo Pulp Lifter (TPLTM) was installed in the Ahafo SAG mill in April 2015 to replace the existing radial pulp lifters. Plant operational data showed delivery of a power saving of 10 per cent, an improvement in throughput of 3.3 per cent, with no loss of grind size. Pulp lifter life was also doubled from 11 to 22 months.However, during subsequent relines when the grates were removed it was found that one in four of the outer pulp lifters were wearing at a faster rate than the remainder. This was investigated by Discrete Element Method (DEM) modelling, which predicted some overtopping and internal recycle within the pulp lifter. Significantly, the model predicted that the recycled material would pass back down every fourth outer pulp lifter, matching the field observations. Subsequently, the DEM investigation was continued and became an R&D project to improve the TPL design. The results are summarised here, leading to the development of the next generation Spiral TPLTM.CITATION:Heath, A, Chaffer, S and Asakpo, E, 2018. The development of optimised pulp lifter design for the Ahafo SAG mill using discrete element method modelling, in Proceedings 14th AusIMM Mill Operators' Conference 2018, pp 585–594 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Aug 29, 2018

By N Cann

In the 10 years from 1998 to 2008 the annual number of fatalities in the Australian mining industry has plateaued (MCA, 2007-08 and abc.net.au website). Despite significant efforts to eliminate fatalities, this is not a comfortable statistic in this very public performance indicator.GHD has been working with the mining and minerals processing industry to identify the key risks that lead to fatalities utilising a semi quantitative risk assessment technique (SQRA®), initially developed to assist Major Hazards Facilities prepare Safety Cases (OH&S, 2007-08) in response to the Longford Incident in 1998 (Dawson and Brooks, 1999).Workshop cross functional teams are assembled from the sites and led by the GHD facilitators to identify the incident types that can have fatal consequences, the causes of those incidents and the controls that are utilised (or could be utilised) to reduce the risk. The risks for each incident type are quantified to produce a risk profile for the facility and the critical controls – the controls that have the greatest impact at reducing the risk of fatality – are selected. These controls are assessed for their adequacy and improvement actions are identified. Prioritisation of the actions is achieved by re-estimating the incident risk profiles.A review has been undertaken using a small sample from the more than 100 individual studies that GHD has completed at mining and minerals processing sites. The five most significant risks reported by sites are:1. Fall from Heights,2. Vehicle/ Vehicle and Vehicle/Pedestrian interactions,3. Entanglement,4. Molten Metals and Materials, and5. Electricity.The most significant reductions in risk identified were found to be by implementing engineering controls. Examples include:1. Chutes to contain splashes and spills of molten materials,2. Redesigning instrument and equipment layouts to take personnel away form high risk areas,3. Designing remotely operated equipment to remove personnel away from high risk areas,4. Proper fire fighting equipment provisions such as deluges around flammable materials, and5. Adequate risk assessment to ensure equipment is designed to handle the real situations and not a design case to meet an arbitrary specification.All of these cases and many of the actions identified in the studies could have been handled through better design and construction early in the life of a project rather than retrospectively fitted after operations have begun.

Aug 8, 2011

Nippon Telegraph and Telephone Corporation (NTT) developed a new construction method (the M-2 method) that could drive a long, curved small-diameter tunnel (4>1.2 m) without human labor. This method employs the cast-in-place lining system, using quick-hardening resin mortar, so that it can greatly increase the driving distance and execute both long distance driving (longer than 500 m) and curved driving with a radius of curvature of 200 m. Furthermore, the central control system with a mini-computer in a vertical shaft enables all work in a small-diameter tunnel, i.e., excavation, lining, and transportation of excavated soil and materials, without human labor. NTT conducted several field tests and a Practical Application Test (P.A.T.) under a public road bearing great traffic. Good results were obtained and the practicability of this method was demonstrated. Therefore, from now on, NTT will apply this ii-2 method to drive telecommunication cable tunnels in urban areas. This method will also be applicable to constructing public tunnel facilities, such as for water, sewage, electricity and gas.

Jan 1, 1987

By T D. H McGrath, R Byleveld, W P. Staunton, J J. Eksteen

"The Gold Technology Group at Curtin University through the AMIRA P420 series of projects has recently developed the integrated liberation leach model (ILLM) for optimisation of gold plants. The model encompasses recovery by both gravity (batch centrifugal concentrators or BCCs) and leach adsorption (CIP/CIL) circuits. The ILLM essentially combines the Group’s well-known standalone models (ie gravity and SIMCIL) to create a robust simulation package.The ILLM process model provides a tool for sites to determine optimum set points for operations to optimise recovery (eg target grind size). It can also be used to predict the effect on gravity recovery, leach recovery and overall recovery when changes are made to circuit design, either temporarily (eg a leach tank taken off-line for maintenance) or as part of a circuit expansion (eg expanded gravity circuit capacity, or addition of leach tank capacity).This paper discusses the capability of the ILLM process model by highlighting a recent case study. The paper also addresses the test work and plant data required as model inputs, as well as limitations and the application of the ILLM to greenfield projects.Citation:McGrath, T D H, Staunton, W P, Eksteen, J J and Byleveld, R, 2016. Application of an Integrated Liberation Leach Model for Process Optimisation, in Proceedings 13th AusIMM Mill Operators’ Conference 2016, pp 173–178 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Oct 10, 2016