Search Documents

By Egan J. R

Changes have recently been applied to the Sullivan Concentrator lead and zinc circuits to treat fine-grained ores which make-up the majority of ore reserves in the mine. Pilot plant testwork conducted in 1990 - 91 indicated that concentrate grades would be substantially improved by reducing the particle size (Pao) of the lead from 38 to 15 ¦m and the zinc from 45 to 24 ¦m. Circuit revisions involved installation of major new equipment including: two 600-kilowatt Vertimills for regrinding, a four metre diametre column flotation cell and a four metre diameter hyperbaric pressure filter for dewatering. Duties of the existing regrind mills were Reassigned.

Jan 1, 1993

Most compact bucket wheel excavators in use are in the small to medium range. Large compact bucket wheel excavators compete directly with con- ventional longer boom excavators which have operational advantages over the large compact. There are, however, situations where the large com- pact excavator is viable. In the development of these large compacts there are a number of technical features to be addressed. In addition the SECV now propose to expand the concept to a large compact bucket wheel excavator with a bridge and loading unit for their Loy Yang Open Cut.

Jan 1, 1989

By N S Melkoumian

While improvements in occupational health and safety (OHS) in the mining industry have decreased fatalities and accidents, little attention has been paid to the cultural confound of 'safety' in the increasingly multicultural mining industry. Occupational health and safety processes often contain assumptions of cultural understanding that may not be shared or understood by mining employees. There are potentially dangerous and costly implications of cultural difference in the mining environment. Some people have been enculturated with high levels of anxiety concerning catastrophe and uncertainty while others have a more laissez faire attitude to accidents and disaster. The level of cultural anxiety about uncertainty can be a major factor in the acceptance of OHS processes. OHS manuals based on a comprehensive set of rules and procedures may assume that the authority of 'rules' is shared by all employees regardless of a variety of cultural understandings when this may not be the case. Similarly, cross-cultural employees may not share a background or acceptance of expensive technological innovation and so resist/avoid the application of new safety equipment. Then too, OHS staff may not realise the significance of religious belief or personal responsibility on employees' attitudes to safety in the workplace environment. A lack of consideration of these cultural elements could have fatal and expensive results. This paper explores the impact of cultural difference in the understanding of OHS in the Mining Industry, presents a model to improve the understanding of the cultural confound in safety, improves analysis of OHS in practical multicultural situations, provides assistance for those involved in OHS training and may become a basis for developing OHS policy and procedure.

Dec 6, 2010

By D Morgan, D Sato, B Lumsden, S Senanayake

Laboratory flotation tests on fresh cyclone overflow samples are a useful tool to troubleshoot and indeed to improve plant performance; however, reproducibility between laboratory flotation test and plant performance is important for interpretation of the laboratory tests and hence their usefulness. Chemical reproducibility can be achieved with the addition of the required reagents; however, reproducing the physics of forces and energy in a 5 L cell compared to a 50 000 L plant cell or a 500 000 L plant cell is not generally studied or discussed. For some tests such as collector evaluation the physics of the flotation process may not be critical, but for some evaluations in the laboratory, it can be important.All flotation plants suffer from losses of valuable <20 µm mineral. Selective mineral aggregation has long been recommended to improve the poor flotation recovery of <20 µm sulfide minerals; however, successfully testing any type of selective sulfide mineral aggregation’s effect on flotation recovery in the laboratory on practical plant samples requires reproducing plant cell physics. The energy input per litre and the forces in a laboratory cell are vastly different to a plant cell. Reproducibility between laboratory and plant tests requires that these differences be minimised. The physics of the laboratory flotation cell is particularly important when fine mineral aggregation tests are carried out.This paper outlines a modified laboratory aggregation and flotation method that closely reproduces plant performance in a laboratory test.CITATION:Sato, D, Lumsden, B, Senanayake, S and Morgan, D, 2014. Development of a laboratory flotation method to test plant mineral aggregation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 173–178 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By Upfold RW, Velzeboer MD

An underground mine fire will influence the ventilation equilibrium in several ways which results in a redistribution of the ventilating quantities and pressures throughout the whole mine. The ventilation carries the combustion products which constitute the greatest danger of mine fires through the mine and provides the oxygen on which the intensity of the fire depends. However, as a result of the ventilat- ion disturbances created by the fire, changes in airflow patterns can take place which are not always obvious, especially when the mine is being served by several fans. The use of com- puter simulation techniques allow for the likely effects to be tested and the different ventilation options to be evaluated as an integral part of the overall emergency/rescue planning and control procedures.

Jan 1, 1981

By F H. Henrfquez, A G. Oroz

Design and operating conditions of large size mechanical flotation cells were evaluated by comparing them with actual operating conditions in a plant. The objective was to determine the time scale-up factor, typically based on empirical rules. Experiments were conducted on the rougher flotation circuit at Minera Escondida Ltd. The circuit consisted of self-aerated mechanical cells of 160 m3, arranged in six parallel banks with nine cells each. The rougher circuit flotation kinetics were evaluated from direct sampling and local mass balances around each cell of the bank. Adjusted overall mass balances were also developed. This information was used to fit different kinetic flotation models, and it was found that the rectangular distribution function was the most appropriate to describe the distributed rate constant for industrial operation. Then, a rougher flotation simulator was developed to describe the actual operation in terms of the operating variables (mass flowrate, solid percentage, feed grade) and the actual volumetric flowrate entering to each cell. In this study feed pulp samples were taken in parallel from the rougher circuit and were simultaneously floated in the laboratory. The kinetic behaviour was then modelled at a laboratory batch scale in order to determine the time scale-up factor between laboratory batch flotation data and industrial size flotation. The time scale-up factor observed for large sized cells, 160 m3, was found to be reasonably similar to those previously determined for self-aerated mechanical cells, but of lower size, operating at similar recoveries. In addition, the relative effect of mixing, between laboratory batch and an industrial flotation bank, was quantified by the parameter, separating the impact that kinetic and mixing changes have on the time scale-up factor. In general, the rougher flotation operation was found to reach the predicted metallurgical target, and the optimal separability criterion was also respected. The diagnostic generates information about the internal state of the process and helps to identify potential improvements for design, operation and control of the circuit.

Jan 1, 2005

By D J. Brake

The risk from fire remains one of the most serious of underground mine disaster scenarios. The impacts of mine fires on the underground ventilation system and the production of toxic gases have been difficult to model and therefore assessments have relied largely on empirical data, historical precedent and subjective opinions. Underground fire modelling software has had limited availability and been technically challenging and time consuming to use especially for routine mine investigations. There has also been no well-accepted set of assumptions for fire modelling in mines, which has resulted in a lack of confidence in adopting its use more widely. This paper describes modelling of three critical fire scenarios in underground hard rock mines: a fire (LHD) in an underground diesel refuelling facility, a fire in an underground explosives magazine and a fire on an underground ore transport conveyor. Modelling was undertaken using VentsimÆs VentFIREÖ fire simulation module. It describes the basis of design, the key assumptions, the methodology used and provides examples of the outputs, conclusions and recommendations. It reviews the impacts of these fires on egress and entrapment strategies in the mine. Some general principles regarding improvements to ventilation circuit design based on this analysis are also recommended. Whilst the fire scenarios were based on actual case studies, they have been disguised for this paper.CITATION:Brake, D J, 2013. Fire modelling in underground mines using Ventsim Visual VentFIRE software, in Proceedings The Australian Mine Ventilation Conference , pp 265-276 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 1, 2013

By J Taylor, M Smith, A Tunnadine, D Nikolakopoulos

As Olympic Dam rapidly expands into the Southern Mine Area (SMA) the Mine Geology team has concurrently ramped up underground diamond drilling to sustain rates of above 175 km/a. With >10 underground rigs double-shifting, traditional paper sections used for the management of drill programs were no longer optimal due to scale of operations. An opportunity was identified to modernise monitoring of all underground diamond drill programs, through the integration of logged copper sulfide estimates with Olympic Dam’s first-fully integrated deposit-scale geological model in Leapfrog Geo. This paper describes the transition within the Mine Geology team from reliance on 2D paper sections, towards near-real time 3D geological modelling for optimising end-of-hole decisions in the field. This transition was enabled by innovative database solutions informing locally constrained implicit models, limited by a distance buffer around active underground fan drilling. Due to the high volume of historic drilling, there were significant computational challenges with the implementation of daily production style implicit models at Olympic Dam and initial testing of regular updates to implicit gradeshells and sulfide domains required in excess of 12 hrs to run. The enabling solution was to optimise the interfaces between the AcQuire database, Deswik MDM and Leapfrog Geo to create a dynamic, streamlined workflow that was easily completed by Mine Geologists in accordance with daily production duties. Geologists are now building rapid implicit models for a range of variables from an integrated data set of logged sulfide estimates and existing assays, spatially constrained by 150 m buffers around active drilling using a unique drill fan identifier flagged during the planning phase. Once the live-implicit models are updated, they are exported for visualisation on field tablets to be used during logging and core checks at the start and end of every shift. To manage the risk of ‘going digital’ interpretation remains at the forefront of the drill section close-out process, with Mine Geologists critically reviewing the finished sections on a standardised template with new learnings wireframed and communicated to stakeholders. The Live Field Model has enabled a step-change in the geological effectiveness of diamond drilling, reducing over – and under-drilling ore-waste at Olympic Dam continuing to push drilling effectiveness towards 20 per cent of intercepts >2 per cent Cu. In addition, upside or risk identified during the proactive management of drilling execution can be rapidly capitalised or mitigated.

Mar 22, 2022

By B Vietnieks, N Widmer, L White, E Tata, J Natukunda, D C. Ilouga, J P. Tyler

The Republic of Uganda aims to exploit its’ significant, un-developed iron ore resources to supply the required raw material for developing its’ iron and steel industry across all the stages of the supply chain. Large prospects of iron ore exists in Uganda in the eastern (Tororo) regions and southwestern (Kisoro-Kabale) regions of the country. The Kisoro-Kabale iron ore projects covers mineralisation in hematitic banded iron formation (itabirite) in the north-eastern Congo-Tanzania Craton; covering ten Iron ore prospects. The prospects include Kamena, Karukara, Nyamiringa, Kyanyamuzinda, Rugando, Katagata, Rwengongo, Kijuguta, Kihumuro and Katuna. High-grade hematite ore prospects in south-western Uganda have known grades ranging from 55 per cent to 68 per cent iron ore content with an exploration target estimated at over 500 million tonne (Mt). Small scale production of iron ore from the south-western regions provide raw material to existing steelmaking and direct reduction iron ore plants located in the Jinja and Iganga districts of eastern Uganda. Large quantities of iron ore and other steelmaking raw material, however, are required to be imported into Uganda due to the limited exploration and development of their own iron ore mining operations. A joint collaboration between the European Union (EU), the Department of the Geological Survey and Mines (DGSM), Ugandan Ministry of Mines in partnership with Australian drilling and mining consultancies, ADT Africa and Kalem Group as a EU funded project was undertaken during November 2022 and September 2023. Exploration and evaluation of the ten iron ore prospects in south-western Uganda was undertaken through geological mapping, drilling, assaying, and technical studies with the view to attract investment for the development of Uganda iron ore mining and steelmaking industry. The collaboration developed mineral exploration policy, guidelines and standards, an iron ore exploration manual, a geological data management policy, and to support the sustainable development of iron ore mining in Uganda through building the capacity of local Ugandan geology and mining personnel through the transfer of knowledge and expertise from experienced iron ore experts. The quantification of these resources is an important first step in assessing their economic potential and attracting mining investors. This paper presents an overview of the investigation program and the preliminary results as an important first step in attracting mining investors to this exciting new iron ore province.

Sep 18, 2023

By B Yeganeh, A Sam, A Kohsari

The base of separation at Gol-e-Gohar iron ore plant (Sirjan in the south of Iran) is magnetic separation after milling. Magnetic separation in the plant is divided into two parts: dry magnetic separation and wet magnetic separation. Sixty-five per cent of the plant production belongs to the dry magnetic separator section. Therefore, investigation of this part of the plant is necessary. Prediction of plant production is one of the most important subjects in mineral processing plants. That means, before feed enters the plant, specification of production has been calculated with laboratory methods. The purpose of this paper is the prediction concentrate quality has achieved from the dry magnetic separator. The content of iron in the final dry concentrate will be predicted, with laboratory, pilot and modelling methods, before feed enters the plant. Different variables are used in this approach, which consist of: speed of the first dry magnetic separator (rougher), speed of the third dry magnetic separator (cleaner), iron content in plant feed, size of 80 per cent passing of feed, size of 20 per cent passing of feed and iron content in pilot dry magnetic separation concentrate that performs in a standard manner. The artificial neural network is used for modelling and one of its branches is the radial basis network (RBN). Iron content in magnetic separating concentrate in plant will be introduced as the target and will be calculated with the RBN method. In the RBN method, a set of data enters to neural network and they will be trained and simulated. Finally, the target will be predicted. Ultimately, the original target (actual iron content) and the predicted target (predicted iron content) compare and error of them will be calculated. The obtained result is acceptable and satisfactory.

Jan 1, 2007

By J D. Pease, J M. I Tuppurainen, P D. Munro

This paper examines how legislation and regulation can be external drivers of technical change in mineral processing and extractive metallurgy and how the industry can respond. Two examples are considered; the production of copper metal from concentrates and the cyanide process for gold production.The Clean Air Act (1970) in the USA initiated a wave of attempted innovations in the extractive metallurgy of processing copper sulfide concentrates to meet forthcoming standards on sulfur dioxide emissions. Interestingly, a satisfactory technical solution existed (flash smelting and gas capture) but had not been widely adopted.Nearly fifty years later the primary copper industry finds itself with new challenges. One major challenge is how to deal with the increasing level of arsenic in copper concentrates. Most countries impose an upper limit on arsenic in imported concentrate; typically, 0.5% As or less. Higher arsenic concentrates can be blended with cleaner ones to meet the limit, but this tactic cannot be used indefinitely as the average arsenic level of global concentrates rises inexorably. Further, smelters (often in urban locations) cannot be expected to deal with both ever-increasing arsenic in the feed and stricter restrictions on emissions and disposal. A rising “inventory” of primary copper deposits are already constrained from development by high arsenic concentrate. These deposits will need to be developed if future copper demand is to be met. An economic and technical solution to arsenic is needed. The gold industry may also face challenges in the use of cyanide, by far the dominant lixiviant used in gold and silver production. Public perception has driven restrictions on the use or transport of cyanide in some jurisdictions. History suggests that such pressure is only likely to increase. While there are several alternative lixiviants, none can yet match the utility and economics of cyanide.Such important issues will not be resolved by incremental change or new equipment items. They require development of new process technology - a tectonic event rather than an incremental change. It requires sustained effort (and expenditure) over decades and is very unlikely to result from “business as usual” for producers, suppliers or academics. Past major process developments were driven by a dire need for economic survival or by legislative change. What will drive the future changes?CITATION:Munro, P D, Pease, J D and Tuppurainen, J M I, 2017. Technology change by regulation – a cresting wave?, in Proceedings MetPlant 2017, pp 45–58 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 11, 2017

The tankhouse of the electrolytic zinc plant at Nordenham is operating with a very high operating efficiency of 99 per cent. This has been achieved not only by strict control of the quality of the zinc sulphate cell feed solution but also by all the improvements in housekeeping in the tankhouse developed during the past years: aluminium cathode specification, cathode stripping cycle, edge strips, copper contacts, anode isolators, cell cleaning, fittings and washing devices. During 1987 to 1992 the casting department was completely remodelled in order to improve the quality of the zinc products, the safety of the operations and the flexibility. The remodelling includes the enlargement of the area for the casting shop, the storage buildings and the five casting lines on the same ground level. New lines for alloying products and for SHG25 kg zinc ingots have been constructed. The line for galvanising products has new equipment in some parts and the other lines have been modified.

Jan 1, 1993

By N Jeannee, L Rattmann, M W. N Buxton, A deJong, K Nienhaus, A Soares, P Graham, A Korre, J Benndorf, D Buttgereit

The flow of information, and consequently the decision-making along the chain of mining from exploration to beneficiation, typically occurs in a discontinuous fashion over long timespans. In addition, due to the uncertain nature of the knowledge about deposits and the inherent spatial distribution of material characteristics, actual production performance often deviates from expectations. Reconciliation exercises to adjust mineral resource and reserve models and planning assumptions are performed with timely lags of weeks, months or even years.The key concept of real-time mining promotes a change in paradigm from discontinuous intermittent process monitoring to a continuous process and quality management system in the resource extraction process. The framework includes a real-time feedback control loop that rapidly links online data acquired during extraction at the mining face, material handling and processing with a sequentially updatable resource model. This will allow near real-time optimisation of decisions related to long-term planning, short-term sequencing and production control.The proposed framework integrates the following building blocks in a holistic manner: automated sensor-based material characterisationonline machine performance measurementsunderground navigation and positioningunderground mining system simulation and optimisation of planning decisionsupdating techniques for resource/reserve models.This paper introduces the real-time mining concept and the building blocks and provides a review of the state-of-the-art. Technological readiness of necessary building blocks is assessed, and critical gaps for further technology development are identified. The value added is illustrated by means of a case study.CITATION:Benndorf, J, Buxton, M W N, Nienhaus, K, Rattmann, L, Korre, A, Soares, A, deJong, A, Jeannee, N, Graham, P, Buttgereit, D, Gehlen, S, Eijkelkamp, F, Mischo, H, Sandtke, M and Wilsnack, T, 2015. Real-time mining – moving towards continuous process management in mineral resource extraction, in Proceedings Third International Future Mining Conference, pp 37–46 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 4, 2015

The Olympic Dam copper/uranium deposit was discovered in 1975 and subsequently commenced production in 1988 at a rate of 1.5 Mtpa using the sublevel open stoping mining method. In the following five years the operation underwent two optimisation programs that have increased mine output to the current rate of 3.4 Mtpa of ore. The pre-expansion requirements were annual development of approximately 10 000 m and the placement of around 500 000 m 3 /yr of cemented backfill. Previous to 1995 all hoisting was carried out by the Whenan shaft. The Robinson shaft was commissioned during that year to hoist increasing development mullock tonnages and to allow for increased ore hoist via the Whenan system. In 1996 WMC committed to expanding the output of the operation from 85 000 tpa (1996/97 budget) copper metal to 200 000tpa. The corresponding increase in mine ore production requires expansion to a nominal rate of 9.0 Mtpa. To achieve these increased tonnages, major hardware installations will include sinking of a third shaft capable of hoisting in excess of 9.5 Mtpa, a rail haulage horizon utilising automatic trains, expansion of the existing backfill plant to a production capacity of over 1.8 million m 3 /yr, increasing long term development rates to 15 000 m/yr and increasing the production drilling and blasting rates in line with the higher stope production output. This paper provides detail into the intended hardware (shafts, equipment, etc) of the mining system, and outlines the intended long-term operation and management of the operation. Of particular note is the background requirement of ensuring existing production targets are met to provide critical cashflows into the project during the period of expansion.

Jan 1, 1998

Operating metallurgists spend a significant part of their time running plant trials to compare two or more conditions in order to improve the process, such as a new reagent, flow sheet or piece of equipment. The best way to conduct such a trial is as a paired experiment when testing two conditions (eg 'old' and 'new') or a randomised block design when testing more than two conditions. These experimental designs should always be preferred over alternatives if their requirements can be met, because they block the effect of uncontrolled variables ('covariates') and are the most statistically efficient, ie they will lead to the required level of confidence in the outcome faster than other methods. Sometimes, however, it is not possible to switch condition easily, which is a prime requirement of these methods. In such cases the only option may be to switch condition once only, and compare the process performance before and after the switch. Examples are testing grinding media, large equipment, or long residence time processes such as leach trains or CCD thickeners. This paper considers some data analysis methods to deal with this situation. Modelling with intervention analysis (IA) uses regression models with a dummy variable to indicate the presence or absence of the test condition. IA with a time series model ensures that the residuals are uncorrelated. IA with a process model helps to deal with the problem of covariates. The reference distribution is a method free of any statistical assumptions but is less powerful than the other methods. Cusum charts are a helpful visual aid to interpreting time trends. A combination of these methods can help improve the confidence in the final decision. None are as good as a formal experimental design such as a paired trial.

Jan 1, 2008

By J Harris, J Li, M Shi, P A. Kirsch, D Sprott

Australia has an enviable global reputation as a leader in health and safety outcomes in the hazardous industry of mining, in part due to an increased application of risk management regarding operational planning and mining practice. In 2010, the Australian Coal Association Research Program (ACARP) initiated a major project, RISKGATE, to build, capture and deliver a national body of knowledge to assist companies with the management of risk in coal mining. The online system contains information for tyres, collisions, fires, isolation, strata underground, ground control open cut, explosions, explosives underground, explosives open cut, manual tasks, slips/trips/falls, outbursts, coal bumps and bursts, human–machine interface, tailings dams, occupational hygiene and inrush. In 2014, RISKGATE is developing content for fitness for work (fatigue, drugs, alcohol, physical well-being, psychosocial well-being).This paper analyses underground mining fatalities in Australia and the United States since 2002 and introduces RISKGATE with a focus on the knowledge base for management of hazards in underground operations. Through capturing coal industry expert operational knowledge, RISKGATE provides a cumulative corporate memory at a time of high personnel turnover within the mining industry. This coal-based body of knowledge is a platform that can be evaluated and implemented for other mining domains and high-risk industries within the energy supply chain.CITATION:Kirsch, P A, Shi, M, Harris, J, Li, J and Sprott, D, 2014. RISKGATE and underground operations, in Proceedings 12th AusIMM Underground Operators’ Conference 2014 , pp 11–18 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Mar 24, 2014

By Keyte SG

Gravity methods of recovering alluvial gold are not very efficient at particle sizes below about 0.1mm. Whereas such gold may not have been economic to recover in the past, the same may not be true today. Centrifugal concentrators, like the Knudsen and Knelson bowls, are showing promise after an inauspicious start, at least in New Zealand. The large proportion of heavy mineral in many auriferous beach sands and the natural hydrophobicity of fine gold should make flotation an attractive contender for its recovery. The conventional mechanical flotation cell is effective, but roughing, scavenging and cleaning are necessary to achieve both high recovery and low mass yield. More problematic is the difficulty of maintaining coarse and dense sands in suspension. The air sparged hydrocyclone is effective at recovering fine gold from a fine Colarado River sand, but is not effective for the coarse and dense beach sands of New Zealand. The flotation column shows much promise for these sands, when recoveries of over 80% and mass yields of less than 1% can be achieved in a single pass. The froth separator of the USSR and flash flotation could also be worthy contenders. It is felt that flotation could be limited to naturally and artificially de-slimed concentrates.

Jan 1, 1990

The deep seafloor in Papua New Guinea's proposed Exclusive Economic Zone appears to be a gold-rich province in the same sense as the territory above sea level. Two significant sites with polymetallic massive sulphide deposits forming today are known on neovolcanic ridges in the Manus Basin. Their high precious metal contents have led to renewed interest in the issue of exploiting seafloor mineral deposits. The prospects of finding other, possibly larger deposits in the region appear substantial. This paper reviews current data on seafloor deposits in Papua New Guinea (PNG) and raises some issues relating to future commercial exploration and mining of the sea floor. One of the known PNG deposits could become a prime candidate for the trials needed to develop technology, establish costs, and minimise environmental impact.

Jan 1, 1994

By B Poborowski, A Chen

"For some time, the Australian and Chinese underground coal mining industries have evolvedindependently with minimal infl uence on each other. Despite the fact that in recent years severaltechnologies and solutions have become common to both industries, this trend has seeminglycontinued to the point that there are still many important diff erences in legislation and hazardmanagement systems in both countries. Austar Coal Mine as an Australian based and Chineseowned enterprise has a unique opportunity to benefi t from the technology and knowledge ofboth nations. This paper compares the Australian and Chinese approach towards spontaneouscombustion hazard management in order to exchange experience, identify possible improvements and learn from each other."

Jun 1, 2012

By T X. Le, H T. Tran, K Zaw, T Manaka

"An EXTENDED ABSTRACT is available for download. A full-length paper was not prepared for this presentation. The Truong Son fold-thrust belt (TSFTB) is a prominent tectonic component of mainland Indochina that occurs as a north-west–south-east-trending tectonic entity that extends from north-eastern Laos, straddles the Laos-Vietnam border area and is submerged under the sea basin in east central Vietnam. The TSFTB hosts numerous regional-scale gold and polymetallic base metal deposits, and the mineralisation occurs along the strike of the belt; however, the potential of many of these deposits are inadequately evaluated. The ore mineralisation is hosted by different rock assemblages, including highly metamorphosed Late Proterozoic metasedimentary rocks and Palaeozoic sedimentary and/or volcanic packages, which were intruded by several phases of magma and underwent a number of tectonic events. Several ore-forming styles – including porphyry, Carlin-type and sediment-hosted orogenic Au – were formed during at least two phases of regional thermotectonism that have been identified in the TSFTB. However, all of the major gold deposits/mineralisations are closely related to region-wide structural breaks and many of them are controlled by large-scale, high-strain zones. The fold-thrust structures in the TSFTB therefore play important roles for regional gold mineralisation and metallogeny.CITATION:Tran, H T, Zaw, K, Le, T X and Manaka, T, 2015. Structural controls on gold mineralisation in the south-eastern Truong Son fold-thrust belt and its significance in regional metallogeny, in Proceedings PACRIM 2015 Congress, pp 521–530 (The Australasian Institute of Mining and Metallurgy: Melbourne)."

Mar 18, 2015