Search Documents

By K White, R Hardie, J Merritt, B Kirsch, R Lucas

Constructed stream diversions are a common element of mine sites across Australia. A review of constructed stream diversion performance in the Bowen Basin funded by the Australian Coal Association Research Program (ACARP) in 1999 found over 80 per cent of constructed stream diversions failed to meet regulator and operator expectations. Since that time, improvements have been made in the assessment, design, monitoring and management of constructed stream diversions. Fundamental to these improvements has been the development of a better understanding of the regional stream systems and efforts to replicate the natural stream processes in the function and operation of constructed stream diversions.This paper discusses the history of constructed stream diversions through the Bowen Basin in central Queensland recorded in the outcomes of a series of ACARP funded research projects. Further, the paper reports on the outcomes of a current ACARP funded project that has reviewed the success or otherwise of constructed stream diversions in the region. The assessment has compared the performance of diversions that have been designed to replicate and provide for ongoing stream geomorphic processes with those diversions that were designed and built prior to the development of these design improvements. Based on these investigations we have identified design and construction successes and issues requiring further research and management attention.CITATION:White, K, Lucas, R, Hardie, R, Merritt, J and Kirsch, B, 2013. Challenges and opportunities for constructed stream diversions in the Bowen Basin, Central Queensland, in Proceedings Water in Mining 2013 , pp 73-82 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 26, 2013

To enable ammonium nitrate-fuel oil (AN-FO) to be used on an equal weight basis with nitroglycerine explosives, smaller diameter bore holes became necessary with consequent modifications to drill steel and burden on holes. Detonation of AN-FO in small diameter holes proved successful both with and without primer charges but some alterations were required to adapt anoloders to the smaller holes.Important factors in training all operators in the new charging method were the retention of improved fragmentation, avoidance of excessive overbreak and keeping wall rock dilution to an absolute minimum. The successful storage of ammonium nitrate in climatic conditions with daily temperature fluctuations above and below the critical 90°F has been achieved.INTRODUCTIONTechnical aspects of ammonium nitrate-fuel oil (AN-Fa) blasting agent are well covered in recent literature. This paper deals primarily with the manner of its introduction as the principal explosive underground at Great Boulder Gold Mines Ltd. and with the many problems encountered in the process. Following reasonably successful experimental firings in June 1962', using granular ammonium nitrate and an anoloder, permission was granted by theWestern Australian Mines Department to carry out test work in selected areas of the mine. The permit allowed for fuse firing only, and for a mixture of AN-Fa containing between 5t and 6 per cent fuel oil, with an adequate primer.The use of AN-Fa on an equal weight basis with nitroglycerine explosives, involved smaller diameter holes with alteration to ground burden and modification to drill steel.Initial tests indicated that it was apparent that AN-Fa could not replace gelignite on an equal weight basis if the...

Jan 1, 1965

By B Darlington, L Sandberg, O Vallati

The D47 and D39 Mechanical Dynamic Extra bolts (D47 MDX and D39 MDX) have been developed in response to the ever-increasing demand from the mining industry for rock bolts with high dynamic capacity. To prove such capacity, Sandvik has performed numerous in situ dynamic testing with the unique Dynamic Test Rig (DTR) (Darlington, Rataj and Roach, 2019; Roach, Rataj and Darlington, 2019). To complement the collection of testing data, Sandvik, in collaboration with the Swedish Research Institute for Mining, Metallurgy and Materials (Swerim) have performed additional experiments in laboratory condition using Swerim’s new drop test rig. This rig utilises a momentum transfer method to apply a dynamic load to the bolt. The sample falls together with the mass until the support beam impacts stationary dampers and the momentum energy is transferred to the bolt. Part of the charged energy is released by the dumpers while the remaining portion is absorbed by plastic deformation and/or displacement of the ground support element. The D47 and D39 MDX bolts have been tested at Swerim’s test facility with different levels of input energy. Six tests were performed at the specification energy of 36 kJ and six tests were carried out with the maximum allowable energy from the facility, ie 44 kJ. The bolts confirmed their dynamic performance absorbing the input energy without failure. The D47 MDX bolt absorbed up to 33 kJ with 150 mm displacement while the D39 MDX bolt absorbed up to 35 kJ with 162 mm displacement. This work will present an overview of the drop test rig at Swerim’s facility and a collection of results of the test performed on the D47 and D39 MDX bolts. The test method and results will be analysed and compared to the tests carried out with the in situ DTR.

Nov 29, 2022

By C J. Moran

Given that the mining industry is committed to sustainable development principles and that Australia is experiencing changes to the regulatory environment that aim to modernise the water sector and encourage adoption of consistent approaches, there is a well defined need for the Australian minerals industry to develop a water accounting framework. This requires: key terms and definitions for water metrics for use in the Australian minerals industry that is consistent with the wider water sector, a suite of metrics representing key components of an operationÆs water balance, a calculation method for some of the metrics, and a reporting protocol. This paper presents the methodology that was used to derive these four components. Existing accounting frameworks were reviewed and key terms and definitions that were consistent with current requirements were proposed. A calculation methodology was developed to obtain some of the key indicators and variables that cannot be easily measured directly (water loss through evaporation is an example). The adopted terms and definitions dictated model development, with the conclusion that a systems approach was the most effective calculation process. To test the proposed definitions and calculation methodology, values for water metrics were derived for eight sites. The proposed framework and definitions could deal with the specific situations selected as case studies. The associated calculation methodology produced complete accounts at various levels. Some elements of the accounts could be directly checked against available data and simulations. The framework captured well variations in the reuse efficiencies; reuse efficiency could even vary for similar processes. It is concluded that this preliminary accounting framework provides a consistent language and metrics for quantifying and communicating water management, both at the intersection of the site with the surrounding landscape (through detailed reporting of site inputs and outputs) and within operational activities. Using this consistent framework for quantifying and documenting water use within an operation will provide a platform for compiling and comparing minerals industry water use with other sectors. This may support benchmarking activities within regions or companies and help demonstrate leadership amongst water users in water resource stewardship. The approach presented here is applicable to a wide variety of mining and processing activities, and biophysical environments, and can be adopted as the first step towards developing national water accounts for the Australian Minerals Industry.

Jan 1, 2009

By M Haest

This study demonstrates the application of HyLogging™ technologies for mineralogical characterisation of different iron ore types throughout the Hamersley Province (Western Australia), including a channel iron deposit (Murchison Metals Ltd) and bedded iron deposits in the Brockman and Marra Mamba Iron Formations (BHP Billiton Ltd).Drill core from these deposits was analysed using CSIRO’s hyperspectral drill core logging systems (HyLogging systems), which are commercially available at the AMDEL and AMMTEC laboratories in Perth (Western Australia), through a leasing agreement. These HyLogging systems provide high resolution photographs at 0.1 mm pixel resolution as well as visible and infrared spectroscopic refl ectance data at 1 cm spatial resolution. The minerals identified include haematite, goethite and its subtypes (ie vitreous and ochreous goethite), AlOH-clays (kaolinite, Al-smectite and white mica), carbonates, gibbsite, chlorite, amphibole and hydrated silica as well as water content. The abundance and composition of these minerals was established from the spectral data and was validated against XRF analyses.The full potential of HyLogging systems in the iron ore industry is only starting to be unveiled, but some major benefits have already been demonstrated:• HyLogging systems can delineate different ore zones by mapping the vitreous and ochreous goethites. This has a potentially large impact in mine planning and operations, as hard, vitreous goethite and soft, powdery, ochreous goethite have different processing characteristics that can affect plant throughput if not carefully managed.• HyLogging mineralogy can also be used to support stratigraphic interpretations of the host, for example in subdividing the Dales Gorge 1 - 4 submembers of the Brockman Iron Formation.• HyLogging can have a potentially signifi cant impact on waste rock characterisation, as many of the waste materials can be identifi ed and quantifi ed with hyperspectral data (eg clay-type,• hydration state).• HyLogging can provide accurate three-dimensional (3D) mineralogy to iron ore companies that will empower them to improve future exploration and resource planning.• Application of high resolution photography to further improve ore deposit domaining is also to be considered.

Jul 11, 2011

The past decade hap seen revolutionary advances in com-munications and information-handling techniques which have been stiriulated by "cold war" military requirements and by, current programmes for probing into outer space: The tools used in exploration for petroleum and minerals have been improved significantly as a result of this new space age technology and even greater improvements are on the way.Two areas of technical activity have been particularly fruitful in enhancing the effectiveness of exploration, methods. These are (1) The development of new approaches, based on information theory, for extracting signal from noise more efficiently than before, and (2) The use of high-speed digital computers for storing and processing all kinds of exploration information, not only geophysical but geological as well.In seismic prospecting, use of information theory has led to new techniques such as time-domain filtering, wave-number filtering and correlation methods which have made it possible to obtain usable reflection data from areas which were previously considered NR. Complex playback and other data processing facilities have been developed to apply these approaches.

Jan 1, 1963

By G Zhao, S Hapugoda, E R. Ramanaidou, P Hapugoda, Y Jin, G O’Brien

In 2021 the ports of Port Hedland and Dampier in the Pilbara Region of Western Australia handled 900 Mt of iron ore. This ore was produced in the Hamersley’s mines and transported by trains to the ports for subsequent export. Dust, which is generally considered to be particles less than 100 μm in diameter, is generated at all steps in the supply chain. Whilst all dust may have potential impacts on human health and mangroves and buildings a proportion of the dust is classed as respirable (PM10) dust, which consists of particles <10 μm in diameter. In 2021, in response to the community concern with iron ore dust, CSIRO commissioned an internal study to characterise and benchmark the dustiness of the different ores and to develop targeted strategies to minimise dust impacts, without affecting other iron properties, such as stickiness during transportation. A specific concern is that that the dust in the PM10 fraction may contain significant amounts of particulates, such as free silicates which may have health implications for the workers and residents. This study provided detailed mineral and chemical characterisation of the dust generated from the railed fine ore products for five generic Australian ore types: Australian Channel iron Deposit (ACID), Australian Brockman (AB), Australian Marra Mamba (AMM), Australian Pilbara (AP) and Australian magnetite (AM). The dust from these fine ore products were compared to that generated from a sample of Brazilian Hematite (BH) type ore fines. The ores were evaluated for their physical, chemical and mineralogy properties, dust generating potential and understandings of the relationship between the dustiness of iron ores and their physiochemical properties. The size distributions of the railed fine ore products were determined and a suite of analyses were conducted on subsamples of total (-106 μm) and fine (-38 μm) dust. For all the ores, the total dust fraction contains less Fe and more contaminants (SiO2 and Al2O3) than did the bulk ore. The fine dust fraction contained even less Fe and more contaminants (SiO2 and Al2O3) than the total dust fraction. This suggests that the iron ore dust contains more clay and potentially free silica than does the bulk ore. These findings were supported by optical and Scanning electron microscopy analyses of the samples. Dustiness measurements were made for each of the different ores (-106 μm) to investigate the relationship of dustiness of various iron ores with their physiochemical properties and assess their responses to dust suppression by the application of water sprays.

Sep 18, 2023

By D C. Curry, M F. Young

Many flotation operations need to improve liberation to increase recovery, yet often plant operators are concerned that finer grinding will produce æslimesÆ with low flotation recovery. Yet simple circuits can be designed to give good liberation and excellent fines recovery. The economics of fine grinding has changed fundamentally with new stirred milling processes like the IsaMill. This has also transformed flotation design due to the clean surfaces produced in the inert grinding environment and the narrow size distribution produced by the IsaMill. Past poor experiences with æovergrindingÆ in flotation circuits was often due to the wide size distribution and the degradation of mineral surfaces produced by conventional devices using steel media, like ball mills and tower mills. The correct practice is to design both grinding and flotation together to suit the liberation characteristics of the ore. This may result in several stages of grinding and flotation, recovering mineral as soon as it is liberated, then applying further grinding energy only to those particles that still need liberation. Flotation then occurs in relatively narrow size bands and with minerals with similar liberation characteristics. Though the circuit may look more complex on paper, in reality it is far simpler to operate since each section performs predicably. Circuit design also needs to address materials handling. Finer particles affect froth handling and dewatering, but can still be easily handled by standard products with careful attention to design of launders, pumps and pumpboxes, and de-aeration before thickening and filtering. Excellent examples of designing circuits to include ultrafine grinding include Mt Isa and McArthur River (MRM). In the last decade these operations have produced over ten million tonnes of concentrate with an average grain size below 10 ¦m and above 80 per cent recovery. At Mt Isa, zinc recovery was increased by ten per cent by applying fine grinding to existing poorly liberated streams. In fact, grinding finer in the IsaMill actually improved the recovery of fine particles by ten per cent, and maximum particle flotation recovery occurs for 10 ¦m particles. A more recent example is the flotation of Platinum Group Metals (PGMs). The use of conventional ball or tower milling to improve liberation is severely limited by the impact of commonly associated chromite on classification, and degradation of flotation performance by the steel grinding environment. The ability of open circuit IsaMills to deliver a narrowly sized ultrafine product with clean mineral surfaces is transforming the design of platinum flotation circuits. The science and practice of fine-grained flotation is now thoroughly proven. The availability of the 2.6 MW IsaMill has made ultra fine grinding a practical tool for flotation plant design. It is expected to become a standard choice for future applications of both fine-grained ores and for minerals with difficult flotation characteristics.

Jan 1, 2005

By S Williams, N McBride

The aim of these analyses was to utilise the latest available production information for the Wandoo operation to determine the optimal blasting parameters, costing information and predicted results (fragmentation, muckpile shape and vibration). Much of the data used as input was made available from the information gathered during the excavation of the test pits during 1995. As with any æplanning stageÆ analyses, many assumptions were required to fill gaps in the available data. The calibration of computer blasting models was conducted using data from the last of the test pit blasts (this blast was carried out in material that closely resembled rock expected to constitute the bulk of the base case design pit). This calibration was refined using observation and experience based judgements to extend the accuracy of the predictions as far as possible. All the simulations were performed assuming that the blastholes will be wet (as instructed by BGM). This has consequently determined that the appropriate explosive for the simulations and the actual blasting will be a pumped emulsion/ANFO blend. The following blast design parameters were derived by determining a likely range of powder factor (from other similar scale gold mines) with a median value of 0.62 kg/m 3 being the powder factor arrived at through the field optimisation process conducted during the test pit excavation. The total swell/displacement percentage (volume after blast/volume before blast) largely determines the diggability of a well fragmented muckpile. Consequently where fragmentation is good any reduction of total swell will probably reduce diggabilty. Any reduction of diggability can and should be traded off against increased gold recovery. In most gold mines, diggabilty will be substantially compromised at the balance which produces the most profit. When these considerations are combined with the cost to drill and blast material, processing costs and the achievement of æacceptableÆ diggibility, the analysis becomes extremely complex and qualitative. Many trends are evident including:the relationship between powder factor (for each blast design) and maximum forward displacement (throw), see Figure 1; and the relationship between powder factor (for each blast design) and drill and blast cost per BCM, see Figure 2. The following blast designs are matched to each of three ore-tonnage alternatives (as supplied by BGM) (Table 1). They are all based on powder factor of 0.62 kg/BCM and are considered optimum from a mining æpoint of viewÆ. The costing of each design includes drilling, explosives and labour cost to load, stem and tie-in holes. Using the available rock data and relying heavily on the wall exposures in the test pit(s), it is the opinion of the author that between 20 per cent to 40 per cent of the final walls excavated in the Wandoo pit would be likely to have the angle between the dominant foliation and the wall plane that is well suited to presplitting and be cost-effectively served by presplit technique. The drilling cost for 125 mm blasthole is about $11.40 per drilled metre and the cost of 40 mm presplit explosive is about $140 per 25 kg (17 metre) case. This implies that the cost to drill and blast presplit on the above parameters would be about $10.90 per square metre of presplit face. The remaining wall area would be most cost-effectively delineated using modified production blasting techniques. This requires the use of modified parameters such as smaller hole diameters, smaller spacing/ burden, higher powder factor, free face firing, less rows per blast and longer delays. These altered blast parameters would usually be applied uniformly across the entire blast fired adjacent to the wall and this ætrimÆ blast would relieve burden away from the wall, into the pit. In simplest terms, this method relies upon maximised burden relief to minimise blast energy applied to the wall. It is only applicable where the material to be blasted is waste since the throw achieved is inconsistent with ore dilution control. The largest charge weight per hole for these analyses is 360 kg and the nearest domestic structure to the proposed Wandoo pit is about 6100 metres distant. From these parameters and assuming a worst case example of rock controlled site factor, the predicted ground vibration is 0.5 mm/sec that is about five per cent of the lower limit set down in AS 2187 part two (1993). This suggests that for the current location of neighbours, ground vibration will not be an issue for the Wandoo operation.

Jan 1, 1999

By Smith C. B

Major diamond pipes discovered in Western Australia in the late-1970s exhibited a number of unique features that not only resulted in Australia becoming the largest diamond producer in the world in volume terms by 1986 but also changed geological thinking on the primary occurrence of diamond. They were: - lamproite is an alternative primary diamond host to kimberlite. - the extremely high mean grade of the Argyle lamproite pipe at 5 ct per tonne. - the tectonic setting of the lamproite pipes in mobile zones mar- ginal to the Kimberley Craton in contrast to the traditional African setting within stable cratons. Diamond was one of the earliest economic minerals discovered in Australia but 128 years elapsed between its first recognition and the first Australian economic pipe discovery (Argyle). During that period some 200,000 ct of alluvial diamonds were mined in Australia (mostly in New South Wales), but such alluvial output is insignificant on the world scene where annual production today runs at 95 million ct of natural stones some 76010 of which comes from primary pipe sources such as Argyle which alone produces 30 million ct per annum. Of particular significance therefore is the geological nature of the primary diamond source rocks in Australia. The Argyle and Ellendale Pipes are lamproites, differing from kimberlite in their mineralogy and geochemistry, and characterised by the presence of typical lamproite minerals such as leucite, priderite, potassic richterite, and the abnormally high content of chemical elements incompatible with ultramafic rocks. But not yet widely appreciated is that many other Australian olivine-rich lampro- phyres also contain diamond. Such picritic alkaline rocks can

Jan 1, 1988

By V Shrotri L Muhmood, P Gandhre

The current work deals with the measurement of some thermophysical properties of Ca(NO3)2 based ternary nitrate molten salts as HTF (heat transfer fluid) / TES (Thermal Energy Storage) material for CSP (Concentrating solar power) plants. The density and viscosity of different compositions of the ternary salt mixture containing Ca(NO3)2, NaNO3 and KNO3 close to the liquidus has been experimentally measured. An attempt has also been made to measure the melting point of the salt using the cooling curve technique as well as Differential Scanning Calorimetry (DSC). Thermogravimetric analysis has also been performed to estimate the peak operating temperature of the salt. Compatibility of suitable pipe material (SS304) with molten salt has also been discussed. The salt mixture proves to be a viable alternative to the already existing HTFs like Therminol VP-1 (organic oil) or Solar Salt® in regards to its lower melting point, wider operating range, low cost, nontoxicity, sufficiently high density and comparable viscosity.

Jun 19, 2024

By D K. Weatherley, A N. Mainza, I Govender, L M. Tavares, M S. Powell

It is understood that rocks do not instantaneously transport along a grinding mill and are consequently not perfectly mixed, but this is conveniently overlooked in mill modelling. A lack of understanding of the transport phenomenon and the difficulty of modelling realistic transport in a complex tumbling system, contribute to this. Visual observation of segregation in AG and SAG mills and measured lag time of mill response to changes in feed provide evidence of the influence of axial transport within mills. Incorporating this lag in dynamic models should underpin dynamic simulation of milling circuits for design and for model-based control. Limitations and errors in predicting the influence of increased power via mill length versus diameter, inability to predict pebble production, and a lack of the differential in residence time across rock sizes and competences, all contribute to inadequate design prediction that can be especially acute for large Autogenous mills. Examples of dramatically under – and overloaded pebble regrind circuits and the inability to predict pebble load in AG milling discouraging the application of this energy-efficient option, point to the need for predictive modelling of breakage by competence linked to transport through and out of mills. Incorporating progress in granular flow and mixing, coupled to computational advances enable models to be based on complex breakage and transport models at high spatial resolution. This allows mechanistic models to simulate thousands of times faster than real time, opening the door to more accurate mill design, including dynamics in process simulation and to live simulation for process control – all with advanced mechanistic models. The value of grasping this opportunity is not easily refuted.

Aug 24, 2022

By M Schaffer, T Kewe, N Moffatt

Porgera mine is 95 per cent owned by Barrick Gold Corporation. It is located at an altitude of 2200–2700 m above sea level in the Enga province of Papua New Guinea and produces approximately 460 000 oz per annum with a proven and probable reserve of 6.2 Moz. The refractory ore is ground in a conventional semi-autogenous grinding and ball mill circuit. After the gravity gold is recovered, the slurry is floated, oxidised in the autoclaves and then leached. This paper will focus on the flotation circuit and the recent upgrade of the control system. The five interdependent flotation circuits were challenging for operations to control as they dealt with variable grade, throughput and circulating loads, as well as the physical limitations of the equipment. With the installation of 18 Portage Froth Characterization® (PFC) cameras, the plant’s operation has been converted from a level-control based strategy that was focused on individual cells to one that targets grade and recovery control across the entire circuit. Variability in feed and the corresponding launder issues were addressed with a unique site initiative of deflector plates to indicate filling level. Non-linear closed loop control was implemented directly in the DeltaV Distributed Control System (DCS) using Portage Advantage Regulatory Control (PARC) algorithms and optimised with AwaRE advanced controllers. The most noticeable benefits achieved with the upgrade include improved flotation gold recovery, consistent flotation sulfur grade and autoclave performance. Correspondingly, there was a significant drop in boiler diesel fuel usage and launder overflow conditions.CITATION:Kewe, T, Moffatt, N and Schaffer, M, 2014. Porgera flotation circuit upgrade and expert system installation, in Proceedings 12th AusIMM Mill Operators’ Conference 2014 , pp 345–356 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Sep 1, 2014

By D J. Williams, S Islam

Fine-grained coal tailings slurry undergoes only limited settling and self-weight consolidation, and tends to remain slurry-like and unsuitable for conventional laboratory consolidation testing. In addition, constant rate of loading consolidation testing is more representative of the continuous disposal of tailings slurry into a tailings storage facility (TSF) than conventional step loading. The laboratory consolidation testing of coal tailings slurry under a constant rate of loading has been carried out in a purpose-built, large-scale, slurry consolidometer, instrumented with load cells and pore water pressure (PWP) transducers. In the slurry consolidometer, the rate of loading may be varied to represent the actual rate of rise of the tailings in the TSF. A slow rate of loading increases the test duration, while too fast a rate of loading may build up very high excess PWP, without achieving significant consolidation. For the particular fine-grained coal tailings slurry tested, the rate of loading in the slurry consolidometer is varied to access its effect on the development and dissipation of excess PWP. The resulting consolidation parameters are evaluated and explained using the recorded settlement and PWP data.CITATION:Islam, S and Williams, D J, 2018. Optimisation of constant rate of loading slurry consolidometer testing of fine-grained coal tailings, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 72–80 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

No paper available.

Jan 1, 1996

By D A. Williams, P J. Chapman

The acceptable rate of rise of the tailings beaches on upstream-raised tailings storage facilities (TSFs) is critical to life of mine planning. This is illustrated through a case study in Western Australia presented in this paper. Accurate estimates of expected beach slopes, the maximum rate of rise at which the tailings can be placed, and the dry density that the tailings solids will achieve after deposition (stored density) are required in order to design TSFs that will allow upstream raises to be constructed safely and economically. Where operations have been occurring for some time, these three parameters are able to be measured and can be well-defined. If process plant throughputs are proposed to increase through mine expansion, for example, increasing the rate of rise of the tailings can compromise the potential for upstream TSF raising, thus influencing the viability of such an expansion, the timing for its implementation, and significantly increase costs.This paper outlines how rate of rise can be a key constraint, and that ‘rules of thumb’ that are typically applied may not result in the outcomes they were meant to achieve. An example of an experimental method to justify an increase to the ‘rule of thumb’ ~2.5 m/year limit for gold tailings in a semi-arid climatic setting is discussed, followed by rate of rise modelling that ultimately framed the decision-making process for a mine expansion. The rate of rise modelling method was adopted to carefully distribute tailings deposition across four TSFs, comprising nine separate tailings cells, in order to maintain appropriate rates of rise. The implications resulting from various deposition splits are presented, including the need for expansion. In addition, this paper outlines the effect of rate of rise on the state (density) of the tailings after deposition, and provides commentary on how anecdotally acceptable rates of rise, based on the aforementioned ‘rule of thumb’ of 2.5 m/year may not provide assurance of geotechnical stability through the tailings achieving a dilative state, as has been thought in the past. An example of the influence of rate of rise on the state of the tailings, with respect to air-drying and the critical state line (CSL) for the material, is presented. The data indicate that reducing the rate of rise may allow a higher dry density to be achieved through air-drying (evaporative desiccation), sufficient to move the material from the contractive to the dilative zone (i.e. from above the CSL, to sufficiently below it).CITATION:Chapman, P J and Williams, D A, 2018. The importance of rate of rise in life-of-mine planning of an upstream raised tailings storage facility – a case study, in Proceedings Mine Waste and Tailings Stewardship Conference 2018, pp 350–360 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Jul 23, 2018

By K Osten, N Scagliotta, G Lane

Oceana Gold (New Zealand) Limited operates the Macraes Gold Mine near Dunedin on the South Island of New Zealand. The orebody is mineralogically complex and comparatively low grade requiring a series of unit processes and resulting in a relatively complex plant. As part of Oceana GoldÆs ongoing Business Improvement program, a concerted effort has been made to focus on operational efficiency. One aspect of this has been the efficient use of energy in the gold recovery process. A benchmarking process has been developed for the Macraes operation that includes comparison with other operating mines and theoretical design. Criteria for determining operational efficiency have been developed. While benchmarking is, in theory, a simple process, this paper looks at putting benchmarking into practice by catering for variability in ore and associate processing methods. The unit processes discussed include the comminution circuit, flotation plant, pressure oxidation plant and gold recovery circuits.

Jan 1, 2004

By F Sinaga, E Widijanto

PT Freeport IndonesiaÆs Deep Ore Zone (DOZ) mine is the new underground block caving mine within the East Ertsberg Skarn System (EESS) which started production in mid-2000. The DOZ will produce 25 000 tpd using mechanised block cave mining method and will be the fourth underground mine opened within the EESS deposit. A review of the DOZ extraction bolting design was conducted in November 2000. The aim of this review was to re-evaluate the effectiveness of the current design in relation to bolt length and spacing and to challenge some questions about the technical background of the design. For instance, the influence of the rock condition on the design. To review this bolting design, several books and papers are reviewed and several experienced people have been contacted to give their opinion. The methodology used for this review is:reviewing the technical background of current design; collecting ideas and alternatives; collecting data from books and personal communication and conducting analysis; and conclusion and proposed design.

Jan 1, 2002

By M Scoble, A Ostry, J Shandro

Mining companies are not ill-informed on the topic of community health. There have been a number of research studies that have illuminated community health issues associated with mining, especially in the western Canadian province of British Columbia. However, what is missing amongst the literature is the perspective of mine managers and mining executives on this topic. This is important as mine managers and executives face a number of issues related to community health and are under pressure to consider the topic in more detail. This paper presents results from an exploratory qualitative investigation based on grounded theory research techniques into current community health considerations from the perspectives of mine executives and mine managers working in Western Canada. Interviews were conducted between February and May 2012 with 11 mining versus ten mining executives and managers who represented operating mines or mining umbrella organisations in Western Canada. Participants report on general community health issues that are perceived to be important, the perceived role that the mining sector should play?in contributing to community health and how this differs in Western Canada as compared to locations abroad, and?risks companyÆs face in making community health contributions. This paper concludes by drawing attention to pressing health needs that are present in Northern, rural and Aboriginal populations in Western Canada and provides a platform for future research initiatives focused on improving the health and well-being of communities associated with the mining industry. CITATION:Shandro, J, Scoble, M and Ostry, A, 2012. Community health considerations from mining executives and managers in western Canada, in Proceedings International Mine Management 2012, pp 97-104 (The Australasian Institute of Mining and Metallurgy: Melbourne).

Nov 20, 2012

By K Higuchi, K Saito, O Ishiyama

Iron ore in Australia is predicted to increase in its phosphorus content in the near future, which is detrimental to properties of steel product. Steelmakers are concerned by the content of phosphorus in iron ore will exceed limits for steelmaking and increase the converter slag ratio to molten steel, which will finally lead to a decline in competitiveness in high-grade steel production. In this paper, fundamental development of a dephosphorisation technique by reduction gasification is considered. Basic reduction examination was carried out using Australian and a synthetic model iron ore sample with phosphorus compound reagent, varying reaction time and composition of substances to find out suitable process condition for dephosphorisation. With successful lowering of phosphorus concentrations by gasification reduction of the iron ores, dephosphorisation was assumed and further elucidation works were carried out. More than 10 mass per cent of dephosphorisation ratio is obtained from Australian iron ore through batch-type 25 g furnace experiment using hydrogen as a part of reducible mixed gas. Lowering of phosphorus content occurred preferentially either in wustite or in another reducing zones, suggesting a relationship between reducing conditions to efficient dephosphorisation of iron ores. Another result of the fundamental experiment using a model sample with reagent is different dephosphorisation occurred with different reagents contributing to with unified reduction model for phosphorus, providing positive possibility for comparative evaluation, even if new morphologies of phosphorus in iron ore are clarified in future. According to these approaches, it is important to reduce iron ore efficiently and to avoid gasified phosphorus retaining and reattaching to adjacent iron ore particle at the same time. A kiln-type furnace is suggested to overcome previous technical issue, and additional experiments using larger rotating furnace were carried out for verification.

Sep 18, 2023