Search Documents

By H. J. French

WITHIN the past few years, particularly because of the rapid growth of the airplane industry during the war, considerable attention has been paid to the manufacture of light-wall cold-drawn seamless and welded steel tubing for structural purposes. While the manufacture of such tubing is not, in itself, a difficult matter, some difficulties have. been encountered in producing the same under specifications requiring definite physical properties. It is the purpose of this paper to describe the methods of manufacture and the properties that may be obtained by such methods for tubing coming within about ½ to 2 in. (12.7 to 50.8 mm.) outside diameter and 10 to 22 Birmingham wire gage (0.134 to 0.028 in. wall thickness). Such tubing is largely used as structural material in the aircraft industry, and it is of the utmost importance that the physical and chemical properties should be known, and also that the various factors entering into the manufacture should be under such control as to allow these properties to be varied and held within definite limits. In general, tubing may be divided into four classes: namely, specialty tubing, such as riveted-sheet or plate, lock jointed, etc.; brazed tubing; welded tubing; and seamless tubing. Welded tubing may be divided into hot product, such as lap welded and butt, welded, and cold product, such as acetylene and electric welded. Seamless tubing may be hot rolled or cold drawn.

Jan 9, 1919

By R. J. Brison, R. D. MacDonald

This chapter is written primarily from the standpoint of development of flotation processes for treatment of specific ores. However, most of the principles and techniques discussed are equally applicable to other forms of applied flotation research such as improvement of procedures in existing plants and development of new reagents or methods without reference to specific ores. Because it is not possible to cover this subject in detail here, much of the material presented is in the form of a guide to the literature, with emphasis on readily available, English language publications. Details are included only if considered to be widely applicable or not readily accessible in the literature. Related subjects which are covered elsewhere in this volume, such as flowsheet design and statistical techniques, are not emphasized in this chapter. The material presented is intended primarily for those familiar with the theory and practice of flotation, but with limited experience in applied flotation research. It may be of value to the experienced investigator as well, by calling to his attention some useful viewpoints or techniques that he may have overlooked. It has often been said that flotation is more of an art than a science. In- deed much of the knowledge of flotation behavior is empirical. However, the unsystematic, artisan approach to flotation problems results only in an ac- cumulation of unrelated data. Like any other physical or chemical process, flotation is amenable to investigation by systematic experimental methods. The experiments should be based, as far as possible, on an understanding of the natural laws that govern the process and on good experimental procedures. SAMPLING OF A DEPOSIT In working out a flotation process for a mineral deposit, no step is more important than that of obtaining a suitable sample or samples. Experimental procedures cannot compensate for the lack of a representative sample. Methods of sampling a deposit have been published elsewhere,l-4 but a few points are of special importance from the standpoint of flotation. First, the sample should be representative of the deposit, not only in respect to chemical composition, but also in respect to mineralogical composition and degree of dissemination of the valuable minerals. To help ensure

Jan 1, 1962

By C. E. Birchenall, W. Batz, H. W. Mean

AT temperatures between 1095' and 1347ºC, 13 runs have been made on the diffusion of silicon in iron. In two of the runs the couple compositions were entirely within the loop of the Fe-Si system; the base alloys contained 0.0 and 1.0 wt pct Si. The other runs in which the couples consisted of a 2.3 wt pct Si alloy welded to a 3.7 pct Si alloy were a phase throughout. The alloys were made by melting electrolytic iron and commercially pure silicon. Trace impurities were not determined. The butt welded couples were diffused in an inert atmosphere of argon or hydrogen. After cooling, cuts of two mils or greater thickness were machined parallel to the weld interface. The chips were analyzed for silicon. When the concentration and distance data were examined on the conventional probability plot,' no marked variation of the diffusion coefficient with concentration was indicated over the narrow composition ranges employed. Therefore, a single diffusion coefficient is recorded for each run in Table I. The temperatures and atmospheres of the diffusion anneal are listed along with the compositions of the base alloys. For a iron the silicon diffusion coefficient is given by the equation: D = 0.44 e-48,000/RT where R is the gas Constant and T, the absolute temperature. However, since the scatter in the data is fairly large, the activation energy may be in error by as much as 6000 cal per g-atom. The two ? iron points do not permit estimation of the activation energy with any reasonable certainty. They do indicate that the coefficients reported by Smithells2 and Jost,3 based on the work of Fry,4 are much too high. Although very dilute solutions in iron of manganese,5 nickel,8 cobalt,7 and molybdenum8 give dif- fusion coefficients quite close to those obtained for self-diffusion in iron, the silicon values are considerably higher, though of the same order of magnitude. This seems to be consistent with the fact that the silicon atom is the only one of those listed here which is appreciably smaller than iron. The authors are grateful to the Office of Naval Research for their support of this work under Contract N6ori-47, Task order IV, Project NR 031-184, to J. K. Stanley and the Westinghouse Research Laboratories for the silicon alloys used, to several steel companies for the silicon analyses, and to C. Wells, of the Metals Research Laboratory, Carnegie Institute of Technology, for numerous suggestions during the course of the work. References 'C. Wells: Atom Movements (1951) Chapter 2. A.S.M. 2C. J. Smithells: Metals Reference Book (1949) p. 405. Interscience. Pub. Co. 3W. Jost: Diffusion (1952) p. 223. Academic Press. 4 A. Fry: Stahl und Eisen (1923) 43, p. 1039. T. Wells and R. F. Mehl: Trans. AIME (1941) 145, p. 315. "C. Wells and R. F. Mehl: Trans. AIME (1941) 145, p. 329. 7M. F. Hawkes and R. F. Mehl: Trans. AIME (1947) 172, p. 467; Metals Technology (August 1947). .J. L. Ham: Trans. A.S.M. (1945) 35, p. 331.

Jan 1, 1953

By Shiou-Chuan Sun, R. F. Wesner, J. D. Morgan

FOR successful electrostatic separation, the behavior of the component minerals of the tested ore under various conditions should be known. In the course of investigation, it was found that these are difficult to measure accurately by the presently available methods. The method used by Johnson1 is handicapped by the fact that particles in the extreme front and rear end of the falling stream are difficult to control or observe accurately. Furthermore, this method is not applicable when the tested sample consists of more than one mineral. The deflection method, as reported by Fraas,' is inadequate to show the differential amounts of mineral particles deposited at the various horizontal positions under the grounded roll of the separator. This weakness is further noted when the tested sample contains more than one mineral. The purpose of this paper is to introduce a new method capable of measuring the behavior of mineral particles under various conditions, and of defining the optimum condition for separation. The main factors which influence the behavior of mineral particles in electrostatic separation are also described. dividing gauge and the two attached collecting chutes of a Johnson separator.~ This distribution analyzer consists of sixty or more 1.0-cm wide cells as shown in part in fig. 1; it has been fully described in a previous article." Except where otherwise stated, the testing procedure used in this paper is as follows: (a) calculate the weight of feed for a l-min run at a constant feed rate of one layer of closely packed particles falling on the grounded roll; (b) weigh and dry the feed at 100°C for 12 hr; (c) place the top of the distribution analyzer level 4 cm below the bottom of the grounded roll, so that the cells are longitudinally parallel to the grounded roll and the zero edge of a suitable cell is directly under the front vertical tangent to the grounded roll (see fig. 1); (d) with the charged roll at a negative potential of 15.5 kv, the dry hot sample is introduced into the feed chute at a constant feed rate; and (e)

Jan 1, 1951

By Shiou-Chuan Sun, R. F. Wesner, J. D. Morgan

FOR successful electrostatic separation, the behavior of the component minerals of the tested ore under various conditions should be known. In the course of investigation, it was found that these are difficult to measure accurately by the presently available methods. The method used by Johnson1 is handicapped by the fact that particles in the extreme front and rear end of the falling stream are difficult to control or observe accurately. Furthermore, this method is not applicable when the tested sample consists of more than one mineral. The deflection method, as reported by Fraas,' is inadequate to show the differential amounts of mineral particles deposited at the various horizontal positions under the grounded roll of the separator. This weakness is further noted when the tested sample contains more than one mineral. The purpose of this paper is to introduce a new method capable of measuring the behavior of mineral particles under various conditions, and of defining the optimum condition for separation. The main factors which influence the behavior of mineral particles in electrostatic separation are also described. dividing gauge and the two attached collecting chutes of a Johnson separator.~ This distribution analyzer consists of sixty or more 1.0-cm wide cells as shown in part in fig. 1; it has been fully described in a previous article." Except where otherwise stated, the testing procedure used in this paper is as follows: (a) calculate the weight of feed for a l-min run at a constant feed rate of one layer of closely packed particles falling on the grounded roll; (b) weigh and dry the feed at 100°C for 12 hr; (c) place the top of the distribution analyzer level 4 cm below the bottom of the grounded roll, so that the cells are longitudinally parallel to the grounded roll and the zero edge of a suitable cell is directly under the front vertical tangent to the grounded roll (see fig. 1); (d) with the charged roll at a negative potential of 15.5 kv, the dry hot sample is introduced into the feed chute at a constant feed rate; and (e)

Jan 1, 1951

By B. W. Frazier

At a recent meeting of the North of England Institute of Min ing and Mechanical Engineers, during a discussion upon the com pression of air, attention was called to an apparent anomaly in the phenomena attending the compression. At a subsequent meeting this apparent anomaly was explained by Prof. Herschel, and all the facts observed shown to be strictly in accordance with the laws of thermodynamics. Upon reading the report of the discussion in the published transactions of the society, it occurred to me that an attempt to determine mathematically the amounts of energy (whether in the form of heat or of work) expended and absorbed in compressing air, and causing it to perform work by expansion, might prove of use to some who have not access to any treatise upon the application of the laws of thermodynamics to the compression of air, and who have not the time or the inclination to make such application for themselves. The apparent anomaly noticed was this: If air be compressed, and at the same time, by the sufficient application of a cooling medium, kept at a constant temperature, the indicator diagrams in the

By Cloyd M. Smith

A few years ago, the Ventilation Committee established the practice of resenting one topic each year for discussion at the annual meeting. The practice has met good response on the part of committee members and I suggest that it be continued. The topic chosen for this year, "Underground Anemometry," is a topic which has bothered me for more than 20 years. It seems to me that the coal industry is content to rely on slipshod methods for measuring the rate of flow of air underground, so I prefaced my discussional charge to committee members with the statement that I regard air measnrements made in the usual way, with hand held anemometer, as no good. Agreements and disagreements came in from more than a dozen engineers, some of whom are with operating companies, coal and metal; some with manufacturers; others with government agencies. The statement was accompanied by a questionnaire on the use of the rotating vane anemometer and by one describing two methods of using a mechanically held anemometer. The questionnaire will be considered first. The questionnaire and statement are as shown on pages 5 and 6, the committee members and respondents are given on page 4, and the general comments of the latter on page 5. Questionnaire 1. Has your company or agency issued written instructions for care and use of anemometers? If so, please enclose a copy with reply. Only one answer, McElroy's, was affirmative. It gave reference to Bureau of Mines publications1'5 which recom- mend the hand held anemometer for rough measurements and indicate that am accuracy of 5 pct can be had if calibration and method factors are used. Mathews said that instructions are principally oral while Maize reported that state inspectors of his department are well trained in use and care of anemometers. 2. Are your anemometers calibrated periodically? If so, by their manufacturer? or by? Are calibralion corrections applied to all observed mean velocity readings? Only one respondent, Lee, answered negatively as to calibration. This means that anemometers are generally calibrated but the questionnaire failed to ask how often this is done. As no one volunteered the information, we have no data on this point. In six cases the instruments are sent to their manufacturers for calibration. but Krickovic reports that his company limits manu-facturers' calibrations to anemometers which are used by operating personnel; those used by the engineering department being calibrated by U. S. Bureau of Standards. The Anaconda Copper Mining Co. has its ventilation engineers calibrate its anemometers. Most of the respondents say that a calibration correction is applied to each mean velocity reading, but Krickovic limits this to surveys made by the engineering department. Since Lee does not calibrate, he has no correction to apply. Maize reports that his department has its anemometers calibrated but does not apply corrections. 3. Do your men hold the anemometer by hand in measuring air flow? for 1 min? or traverse the section? for 1 min? or at? points for 5 sec each? Of 10 replies, 6 were "yes," 3 were "no," and one was "seldom" with respect to holding by hand. Among the six hand holders, four hold in a central position in the measuring section for a minute, except that two of them, Krickovic and Matthews, traverse the section by hand for survey or fan test. Their operating personnel hold by hand, centrally, for routine measurements. McElroy sometimes traverses with hand-held anemometer in rapid survey work. 4. If the anemometer is not held by hand, how is it supported? Augustadt supports the anemometer on an adjustable rod, Condon on "a rod of sufficient length to reach all points with observer standing in one position throughout traverse and at arm's length from plane of traverse." I presume that arm's length must be interpreted liberally enough to allow for arm movement, otherwise it would be impossible to manipulate the anemometer throughout the traverse section. Mancha upholds Condon in this method of traversing. Glanville hangs the anemometer on the end of a 4-ft staff by the hasp at the top of the anemometer frame. McElroy mounts it on the end of a rigid square shaft, 12 in. long, the staff being at right angles to the axis of the instrument. He traverses the section in two halves, holding the anemometer 3 feet from his body.

Jan 1, 1950

By John L. JR. Schroder

INTRODUCTION-SYSTEM DESIGN The design of an underground mining operation requires the integration of transportation, ventilation, ground control, and mining methods to form a system which provides the highest possible degree of safety for mine personnel; the lowest cost per ton of product; the most suitable quality of final product, considering its intended use; the maximum percent recovery of the reserve, consistent with cost and subsidence rights ; and the minimum disturbance to the environment. The selection of mining method is generally the controlling factor in overall mine design. Some important considerations in the choice of mining method are : 1) Depth of cover over the coal seam. 2) Strength and thickness of rock strata in the overburden. 3) Characteristics of the coal seam, including thickness, nature and location of impurities or irregularities, dip (or pitch), nature and direction of cleavage, hardness, and structural strength of the coal. 4) Nature and strength of the immediate roof (top) over the coal seam. 5) Nature and strength of the floor (bottom) under the coal seam. 6) Presence and amount of explosive gas (methane). 7) Quantity of water likely to be encountered in the mining operation. 8) Any previous or concurrent mining in seams above or below the coal seam to be worked. 9) Any restrictions on recovery required for subsidence control. Topographical and geological reports and maps of the area are usually available from state and federal geological surveys, and contain excellent general information to guide more detailed investigations. Exploratory drilling, and the plotting and analysis of the information thus obtained, are essential steps in any development program, and aid in the correlation and evaluation of information gained by other means. Other good sources of information are operating coal mines that may be in the same

Jan 1, 1981

By Kurt Kennedy

A method is described by which three elements can be condensed simirltaneously on a common substrate in such a way that the composition varies with position on the substrate. Almost all possible combinations of three solid elements can be formed in a single evaporation. The three elements are heated by magnetically deflected electron beams. The alloys and cornpounds formed by this method generally correspond to those trade by other methods; however, many exceptions exist. Simple symmetric crystallographic phases tend to form in preference to more complex phases. The Nb-Sn. Cr-Fe-Nt, and other systems of alloys made by this method will be discussed. Phases that form very slowly, such as the o phase in Cr-Fe alloys, may be formed rapidly by this method when certain substrate temperatures are used. STUDYING all the mixtures and compounds of two or more elements by the preparation of individual samples forces the investigator to make sampling sufficiently close together so that the properties of the intermediate compositions can be inferred. A completely unknown system will require a dis c our aging ly large number of preparations in order to fully know all its properties. For the purpose of expediting this type of investigation, methods have been devised to prepare samples that have a continuous variation in composition over some predefined area. The code-position of two elements onto suitable substrates has been used to produce alloys or compounds that have variable compositions depending on their positions on the substrates Composition gradients have been formed by depositing a wedge-shaped layer of one element and then depositing a second wedge-shaped layer on top of it such that the total film thickness is kept constant. Concentration equilibrium perpendicular to the surface is then established by annealing.4 This paper describes a method for the simultaneous condensation of three volatile components on a substrate such that there is a regular variation of composition with position on the substrate. The arrangement of the evaporation sources and the substrate is shown schematically in Fig. 1. Materials to be evaporated are placed in three water-cooled crucibles located at the corners of a 10-in. equilateral triangle. Electron beams from cathodes located below the crucibles are bent 180 deg by magnetic fields and focused on the material to be evaporated. The cathodes are connected in parallel to a constant-current 12-kv power supply. The distribution of emission current from each cathode is controlled by filament temperature. When materials that sublime are to be evaporated, the electron beam is deflected by an auxiliary ac magnetic field so that the beam moves over the surface of the evaporating material rather than digging a hole in one spot. The substrate is a 10-in. triangle of 2-mil stainless steel or molybdenum which is stretched against a slightly curved heat sink by a frame as shown in Fig. 2. This frame and heat sink are located so that each corner is directly above an evaporation source. The heat sink has three radiant heaters at each corner that can be separately controlled permitting the

Jan 1, 1967

By R. E. Lund

Josephtown Smelter employs the St. Joe-developed electrothermic process for producing zinc metal and zinc oxide. The process uses resistance-type electric furnaces. Flow of current through the sintered ore and coke charge develops the energy required for smelting at the reaction sites. To produce zinc metal, the furnace off-Gases bubble through a large "U"-tube filled with molten zinc which condenses the zinc to liquid; the metal is then mechanically cast into slabs. To produce zinc oxide, the furnace vapors burn in air and the resultant powders are collected. The smelter comprises three distinct circuits. One circuit produces American Process zinc oxide and high grade metal; another circuit produces tailor-made alloys of controlled lead and cadmium content; the third circuit produces prime western zinc metal and feedstock which is refined into special High grade metal and French Process zinc oxide. The roasting circuit utilizes multiple-hearth furnaces for deleading the zinc concentrates; fluid bed and suspension roasters are employed for desulfurization. Sintering produces a hard, porous furnace feed. The flexible smelting process is adaptable to consuming various kinds of secondary material. Extensive residue treatment accomplishes high overall zinc recovery. Smelter by-products include sulfuric acid, cadmium, and mercury.

Jan 1, 1970

By Frank H. Macpherson

FEW people realize the tremendously important part that Saline and Pulaski Counties in central Arkansas have played in the winning of the war. The present favorable war situation might have been very different if we had not had the bauxite produced during the past two years from these two small areas, a total of about 15 square miles. As a general statement, it can be said that the Arkansas bauxite deposits are, individually, relatively small, irregular in thickness, somewhat scattered and, therefore, compared with coal or iron-ore or open-pit copper deposits, relatively ill adapted to a rapid and drastic expansion in output. A few years ago it would have seemed an impossibility for these two counties to produce over six million long dry tons of bauxite in one year. However, with the cooperation of the operators, that is what happened in 1943, when the state of Arkansas achieved the seemingly impossible with a production of 6,020,684 1 long tons (dried equivalent) of bauxite ore during the calendar year, compared with an average annual production of 323,725 2 tons in the period 1931 to 1941. It became apparent early in the year 1941 that the United States soon might be drawn into the war, and, therefore, that an immediate study of the domestic metal situation was necessary. Aluminum is by far the most important metal used in the manufacture of aircraft and many other implements of war and it was evident that there would have to be a tremendous increase in the domestic production of bauxite, which is practically the only present source of this metal. As more than 95 per cent of the known bauxite reserves of the United States was in Arkansas, careful preliminary studies were made in that state by representatives of the United States Bureau of Mines, the United States Geological Survey and the War Production Board in the summer of 1941. Reserves in other states also Were studied. The result of these studies was a recommendation by the War Production Board that mining in the bauxite-producing areas of Arkansas be geared for maximum production, in order to supply sufficient ore for this country's war requirements and, if necessary, to supply the war needs of Canada as well. The annual goal of eight million long tons (dry Weight) set for Arkansas by the War Production Board Was exceeded in 1943, when in August the output reached a rate equivalent to more than 8,300,000 long tons, dry basis. Because of the comparatively small tonnage of bauxite reserves, Congress appropriated funds for an extensive drilling program to be carried out by the Bureau of Mines in cooperation with the Geological Survey. Drilling began in May 1942 but owing to delay in delivery of drills, and trucks upon which the drills were mounted, the program did not get into peak operation until early in 1943. By the end of July 1944, the Bureau of Mines records indicated an addition to the Arkansas reserves of 10,000,000 long tons (wet basis) in place

Jan 1, 1945

By R. M. Brick, Arthur Phillips

The Institute of Metals Division Lecture in 1936, given by R. F. Mehl, on diffusion in solid metals1, was introduced with the statement that "the phenomena of diffusion are intimately related to many basic problems of the metallic state, but in addition to this the process of diffusion is of first importance practically." In view of the scope of that lecture, it does not seem necessary to review the importance, history or present status of diffusion problems. One aspect of the subject of diffusion that has received little attention became of some immediate importance in the course of a study on segregation. When a solid solution alloy freezes, the familiar mechanism of solidification requires that the first nuclei formed be low in solute concentration, with a resultant normal segregation or coring effect during freezing. Theoretically, musion of solute atoms during solidification should result in a homogeneous solid solution. Actually, of course, it is impossible in most binary alloys to obtain a cooling rate that will permit diffusion to eliminate coring in the freezing dendrites. For a given alloy, the extent of diffusion attained up to the point of final solidification will determine the degree of enrichment in solute atoms of the final liquid phase. The flow of this liquid into dendritic contraction channels and the solute concentration of the liquid seem to be the determining factors as to whether the final gross segregation is normal, inverse or absent. The purpose of the present study of diffusion was to determine to some extent the separate diffusion rates of copper and magnesium into pure aluminum with a view to clarifying previous results on segregation in these alloys; i.e., the fact that under similar freezing conditions aluminum-copper alloys segregate inversely and aluminum-magnesium alloys segregate normally. Of concomitant interest were the questions of the homogenization times required for segregated ingots or partially melted, i.e., "burnt," structures, and the solution heat-treatment times required for cast, hardenable aluminum-copper and aluminum-magnesium alloys, for worked and annealed structures, and so forth.

Jan 1, 1937

By H. S. Kalish, F. J. Dunkerley

INTRODUCTION AND PREVIOUS WORK THE determination of the low temperature tensile properties of tin and tin-lead alloys was initiated as part of an extensive research program on the phasial equilibria of tin binary systems below 13.2°C and the property changes associated therewith. A survey of the literature revealed that, although some room temperature tensile data were available for tin and a few tin-lead alloys, there existed no survey report of the low temperature tensile properties of these alloys. Accordingly, the tensile data for tin and a series of pure tin alloys containing from 0.01 to 50 pct lead were measured at eleven temperatures from -196 to +20°C and are presented here in survey form. In addition to the importance of these tensile data as a preliminary to certain fundamental research, this information promises also to be of commercial importance because of the 'extensive use now being made of tin-lead solders in refrigeration and gas liquefaction equipment. Occasional failures of the solders in low temperature service have been attributed by some metallurgists to low temperature mbrittlement, while others hold that failure results from the transformation of the tin-rich phase of the solder from the solid white (beta) to the powdered gray (alpha) form. From the data previously available in the literature, neither of these explanations can be completely corroborated. Cohen and van Lieshout1 have established the beta to alpha tin transformation at 13.2°C and have shown that strain accelerates the transformation. Further, they showed that although I pct lead retarded the transformation, it was not eliminated. It will be pertinent, then, to note whether the beta to alpha transformation of the tin-rich phase will occur in a short-time tensile test. Polanyi and Schmid2 studied the tensile . properties of tin single crystals at -185°C and report that tin is brittle at-this temperature. In 1946, Kostenets3 reported that pure tin was brittle at -196 and -253°C, while lead remained ductile at both these temperatures. He also studied the tensile properties of tin-lead alloys containing from 10 to 75 pct lead at -253, -196 and +17°C. The ultimate tensile strength increased more than two times in going from room temperature to -196°C and about three times that value on further cooling to -253°C. All the alloys were brittle at -6°C except those containing more than 75 pct lead. Even at -253°C, the 75 pct lead alloy retained 36 pct elonga¬tion in a 30 mm-ga. length. Creep is also an important phenomenon

Jan 1, 1948

By R. L. Orr, J. D. G. Masse, Ralph Hultgren

The relative partial molar enthalpies of gold and tin in liquid Au-Sn alloys have been measured from Xsn = 0.474 to 0.510 at 696°K, slightly above the melting point of solid AuSn. Within an average precision of 6 cal per g-atom, the data are represented by two smooth curves, which satisfy the Gibbs-Duhem relationship and which do not show any anomalous behavior in the range of composition studied. The results give no support to the hypothesis that atomic associations in the equiatomic liquid alloy resemble those in solid AuSu. LITTLE has been firmly established as to the nature of atomic distribution in liquid metallic phases. A favored hypothesis assumes the existence of atomic groupings in the liquid phase which are similar to those in solid phases occurring at lower temperatures. Beginning with this hypothesis, it is often possible to adjust the values of certain parameters (such as degree of association) so that approximate agreement is achieved with certain features of the X-ray diffraction pattern of the liquid, even though many other possible structures might satisfy the data equally well. Thus, in this manner, the structure of liquid tin has been described as a dispersion of fragments of gray tin in a matrix of metallic tin.1 Four X-ray diffraction studies2"5 have been made of the liquid alloy of composition AuSn at temperatures slightly above the melting point of the solid. Each investigator concluded, on somewhat different grounds, that the liquid consisted to a large extent of arrays of atoms similar to the solid, with admixture of more disordered arrays. Solid AuSn has the nickel arsenide crystal structure: each tin atom has six nearest neighbors, all gold atoms; and each gold atom has six tin and two gold atoms as nearest neighbors. It remains highly ordered to the melting point. The liquid alloy has a large exothermic (?H700° K = -2700 cal per g-atom6) enthalpy of formation, favoring ordering and making the hypothetical molecular association not unreasonable. The possible existence of such solidlike arrays, or of a high degree of order that occurs preferentially at a specific composition in a liquid alloy, might also be revealed by thermodynamic behavior somewhat analogous to that in highly ordered solid alloy phases. The latter often exist over wide composition ranges, within which the highest degree of order occurs at the ideal composition for which the atomic fractions are equal to the fractions of sites which are "right" for each kind of atom. On departing from the ideal composition, the excess atoms occupy "wrong" positions, raising the internal energy and making it progressively easier for additional atoms to occupy "wrong" positions. Thus, on either side of the ideal composition, there should be a pronounced rise in the entropy and enthalpy, which would be shown particularly by the change in the relative partial molar enthalpies, ?Hi, since they depend strongly on d?H/dx. In the one case where accurate measurements have been made, the solid AuCu ordered phase, the structure becomes much less ordered as the composition deviates from the ideal, and relative partial molar enthalpies change sharply as shown by the data6 given in Table I. This suggests the possibility of finding similar pronounced changes in the relative partial molar enthalpies of gold and tin in liquid alloys near the composition AuSn if the postulated solidlike ar-

Jan 1, 1967

By C. F. Kaiser, T. J. Roberts, I. A. Thomson

The Broken Hill Pty. Co. Ltd. grate-kiln pelletizing plant located at Whyalla, South Australia, produced a total of 250,000 tons of fluxed pellets during 1970. More than 180,000 tons were exported to Japan, while the remainder was used in B.H.P. Co. blast furnaces. The pellet plant treats high grade hematite ore fines and has a nominal capacity of 1.5 million tpy. The induration equipment includes a grate 12-ft 2-in. wide by 164-ft 1-in. long, a kiln 18-ft 6-in. diam by 118-ft 8-in. long, and a rotary cooler 50-ft mean diam by 7 ft wide. Operating problems encountered in the production of fluxed pellets are detailed. The most significant aspect of the trial was the increased production, from about 5100 tpd up to a maximum of 7100, brought about by the addition of artificial magnetite to the plant feed. Laboratory evaluation of fluxed pellets showed that pellets having a basicity ratio (CaO to SiO2) in excess of 1.2 have excellent physical qualities. Reducibility and compressive strength after reduction were both higher for these fluxed pellets than for normal acid pellets. Although it was not possible to publish blast furnace operating data, blast furnace trials on fluxed pellets indicated that production was higher and dust losses substantially lower, compared with similar operations on acid pellets.

Jan 1, 1973

By Strathmore R. B. Cooke, Thomas E. Bam

The paper discusses the mineralogy, structure, and strength of magnetite pellets fired in air and in a neutral atmosphere at various temperatures. The information obtained from this investigation is used to explain the origin of the structures occurring in pellets produced by pilot-plant operation. MUCH experimental work has been performed on i-VL the mechanism of agglomeration and pelletiz-ing of moist ore and concentrates and on the process of firing agglomerates, but except for the work of Tigerschiold and Ilmonil much of the published information is empirical, and the literature contains no information concerning the structure of fired pellets. Results of a preliminary study of the micro-structures occurring in pellets produced both in the laboratory and on a pilot-plant scale are presented in this paper. Most of the results were obtained from pellets prepared from Mesabi magnetic taconite, but through the courtesy of the staffs of the Minnesota Mines Experiment Station and the Bethlehem Steel Co., fired pellets produced from limonite and hematite ores and from Lebanon magnetite have also been examined. The work has been restricted almost entirely to pellets produced without additives, the exceptions being those in which coal was added to the filter cake before rolling. Schwartz has described the microstructures occurring in ore sinters produced under reducing conditions.' Many of the structures and constituents he describes are common to fired pellets, but the constituents normally occur in markedly different proportions. His statement that "in all satisfactory sinter the amount of hematite is small, perhaps not over 2 or 3 per cent" is inapplicable to pellets produced by pilot plant operation or by any process in which air is not deliberately excluded. Pilot plant pellets contain over 90 pct by weight of hematite, and those produced in the smaller furnaces of the Minnesota Mines Experiment Station contain more than 80 pct of that constituent. Preparation of Specimens It is difficult to examine unfired pellets microscopically because of their insufficient coherency to withstand sectioning and polishing. Fired pellets sometimes lack coherency and frequently contain holes which are troublesome during polishing. Impregnation of both air-dried and fired pellets is readily accomplished by the use of methyl metha-crylate monomer." The dry pellets are covered in a test tube with excess monomer, to which a small amount of accelerator has been added. When the test tube is placed in a cooling bath and evacuated with an aspirator, most of the entrapped air is removed, and disruption of weak pellets by boiling of the monomer is reduced to a minimum. Polymerization is then effected by immersion of the test tube in a water-bath at about 45"C, this temperature being held for 4 or 5 days. The test tube may then be broken away from the solidified mass and the pellets sectioned by a carborundum wheel or a diamond saw. Where time is important, impregnation is carried out at a higher temperature by Meyer's method.' Air-dried pellets must be impregnated with especial care; otherwise swelling occurs and the solids are displaced. It is more important to be certain that the monomer forms a reasonably complete network throughout the specimen than that all entrained air is removed, and for this reason the vacuum technique may be omitted. Impregnated agglomerated products and pellets are extremely coherent, section well, and may be polished either by hand or by machine. Hand polishing is not satisfactory for the examination of conditions existing at the boundaries of grains, and for this machine polishing must be used. The Graton-Vanderwilt machine gives excellent results, provided that pressure on the specimen is considerably in excess of that recommended by the manufacturer. Mineralogy of Fired Pellets Only two opaque iron minerals, magnetite and hematite, have been recognized in pellets. The complete identity of, these artificial minerals with their corresponding natural counterparts is shown by their mineralographic characteristics and their X-ray structures. Wiistite has not been found. Slag is the most common transparent constituent of fired pellets. Occasionally conditions have been appropriate for the crystallization of fayalite from the slag, and at other times another crystalline sil-

Jan 1, 1953

By Strathmore R. B. Cooke, Thomas E. Bam

The paper discusses the mineralogy, structure, and strength of magnetite pellets fired in air and in a neutral atmosphere at various temperatures. The information obtained from this investigation is used to explain the origin of the structures occurring in pellets produced by pilot-plant operation. MUCH experimental work has been performed on i-VL the mechanism of agglomeration and pelletiz-ing of moist ore and concentrates and on the process of firing agglomerates, but except for the work of Tigerschiold and Ilmonil much of the published information is empirical, and the literature contains no information concerning the structure of fired pellets. Results of a preliminary study of the micro-structures occurring in pellets produced both in the laboratory and on a pilot-plant scale are presented in this paper. Most of the results were obtained from pellets prepared from Mesabi magnetic taconite, but through the courtesy of the staffs of the Minnesota Mines Experiment Station and the Bethlehem Steel Co., fired pellets produced from limonite and hematite ores and from Lebanon magnetite have also been examined. The work has been restricted almost entirely to pellets produced without additives, the exceptions being those in which coal was added to the filter cake before rolling. Schwartz has described the microstructures occurring in ore sinters produced under reducing conditions.' Many of the structures and constituents he describes are common to fired pellets, but the constituents normally occur in markedly different proportions. His statement that "in all satisfactory sinter the amount of hematite is small, perhaps not over 2 or 3 per cent" is inapplicable to pellets produced by pilot plant operation or by any process in which air is not deliberately excluded. Pilot plant pellets contain over 90 pct by weight of hematite, and those produced in the smaller furnaces of the Minnesota Mines Experiment Station contain more than 80 pct of that constituent. Preparation of Specimens It is difficult to examine unfired pellets microscopically because of their insufficient coherency to withstand sectioning and polishing. Fired pellets sometimes lack coherency and frequently contain holes which are troublesome during polishing. Impregnation of both air-dried and fired pellets is readily accomplished by the use of methyl metha-crylate monomer." The dry pellets are covered in a test tube with excess monomer, to which a small amount of accelerator has been added. When the test tube is placed in a cooling bath and evacuated with an aspirator, most of the entrapped air is removed, and disruption of weak pellets by boiling of the monomer is reduced to a minimum. Polymerization is then effected by immersion of the test tube in a water-bath at about 45"C, this temperature being held for 4 or 5 days. The test tube may then be broken away from the solidified mass and the pellets sectioned by a carborundum wheel or a diamond saw. Where time is important, impregnation is carried out at a higher temperature by Meyer's method.' Air-dried pellets must be impregnated with especial care; otherwise swelling occurs and the solids are displaced. It is more important to be certain that the monomer forms a reasonably complete network throughout the specimen than that all entrained air is removed, and for this reason the vacuum technique may be omitted. Impregnated agglomerated products and pellets are extremely coherent, section well, and may be polished either by hand or by machine. Hand polishing is not satisfactory for the examination of conditions existing at the boundaries of grains, and for this machine polishing must be used. The Graton-Vanderwilt machine gives excellent results, provided that pressure on the specimen is considerably in excess of that recommended by the manufacturer. Mineralogy of Fired Pellets Only two opaque iron minerals, magnetite and hematite, have been recognized in pellets. The complete identity of, these artificial minerals with their corresponding natural counterparts is shown by their mineralographic characteristics and their X-ray structures. Wiistite has not been found. Slag is the most common transparent constituent of fired pellets. Occasionally conditions have been appropriate for the crystallization of fayalite from the slag, and at other times another crystalline sil-

Jan 1, 1953

By E. L. Tucker

IN THE metallurgy of precious metals, it has been standard practice for years to use cyanogen compounds, so it was but natural that early investigators in the field of flotation should consider these compounds as possible flotation reagents. In Australian Patent 9508, of 1913, alkali cyanides were described as suitable reagents for the separation of heavy sulfide minerals, the reagents being employed either in an alka-line or neutral circuit. In U. S. Patent 1236501, of 1917, to John M. Tibbet, the use of cyanide in conjunction with soda ash or lime is described. One of the claims of this patent reads, "An improvement in the cyanide process for the treatment of ores comprising, mixing the ore with cyanide solution and oil and alkali: emulsifying the oil in the presence of the ore, the alkali and the cyanide solution, floating a portion of the values in the pulp by producing gas bubbles in the mixture-and removing the values floated." More recently, Sheridan and Griswold, in U. S. Patents 1421585 and 1427235, describe a somewhat similar process and have, successfully introduced it in. the mill of the Timber Butte Milling Co. U. S. Patent 1429544, of 1922, to Stevens, describes the use of double cyanides of copper, zinc, and lead. The success of cyanide as a reagent in the differential flotation of lead and zinc sulfides in highly complex ores is proof that these patents have a solid foundation.. Although the technique of their application to particular ores has been worked out in many cases, no one, so far as is known, has attempted to describe the nature of the action of the cyanide or to determine the ideal conditions for its, application. It was the purpose of the present investigation to gather information on these points. Naturally this would have been an exceedingly ambitious.

Jan 8, 1925

By Frances Jane Cromwell, D. J. McAdam, G. W. Geil

INTRODUCTION IN a series of papers, the authors and their associates have shown that the technical cohesion limit is affected by the same four factors that affect the flow stress, namely, the stress system, plastic deformation, temperature, and the strain rate.16-28 Moreover, each of these factors affects the technical cohesion limit in the same way that it affects the flow stress.‡ The influence of any one of these factors may be represented by a curve of cohesion limits, although only one point on the curve may represent actual fracture. As the term "fracture stress" has come into use with the same significance as "technical cohesion limit," the authors are here using the shorter term with the understanding that it does not always refer to actual fracture. This paper presents the results of an investigation of the flow of notched and unnotched specimens between yield and fracture. A study has thus been made of the flow and fracture of metals as affected by the stress system, and of the ductility of metals as affected by the stress system throughout plastic deformation. Since two of the principal stresses were equal (S2 = S3), the stress systems can be represented in terms of the radial stress ratio, the ratio of the transverse radial stress S3 to the longitudinal stress Sl.* The results of the experiments are represented by a series of complete flow-stress curves for each of the metals investigated, and these diagrams have been used for the development of other diagrams of various types. Ludwik was the first to suggest that fracture occurs when the flow stress becomes equal to a technical cohesion limit. Although Ludwik was incorrect in his view that the technical cohesion limit depends only on the amount of plastic deformation and not on the stress system, he was correct in his view that the flow-stress curve for any stress system terminates at a point representing a technical cohesion limit. The authors have seen some recent references to assertions by other investigators that a point representing the fracture stress need not be on the flow-stress curve. The Ludwik principle, however, would seem to be axiomatic, provided that the flow stress and fracture stress are properly defined and that the fracture stress is properly determined. Disregard of this principle has led to some untenable theories of criteria for fracture. When a metal is very ductile, the conventional method of determining the ductility and fracture stress by dividing the breaking load by the sectional area after fracture, generally gives values that are much too high. With some metals and in some conditions, the fracture stress thus determined may be two or more times the

Jan 1, 1948

Organization Place Date 1918 American Chemical Society Cleveland, O. Sept. 9-12 American Society of Sanitary En Engineers Chicago, Ill. Sept. 3-5 National Petroleum Association Atlantic City, N.J. -Sept. American Institute of Mining Engineers Colorado Sept. 2-7 National Association of Stationary Engineers.... Cincinnati, O. Sept. 9-13 Association Iron, Steel, Electrical, Engineers Baltimore, Md. Sept. 9-14 British Iron and Steel Institute, Autumn Meeting London, Eng. Sept. 12-13 National Exposition of Chemical Industries New York, N. Y. Sept. 23-28 American Electrochemical Society Princeton, N. J. Sept. 30- Oct. 2

Jan 9, 1918