Search Documents

By Charles R. Austiuon, Carll H. Samans

It has been known for several years1 that certain alloys of the Konal type, containing commercial cobalt (99.32 per cent Co and 0.42 per cent Ni) and varying amounts of ferrotitanium, exhibit very high tensile strengths at 600°C. However, their proportional limits and yield pints are relatively low. published data' for the alloys quenched in water from 950°C. and then tested at 600°C. are summarized in the upper section of Fig. I. Similar specimens that were aged at 650°C. for 72 hr., after quench and prior to testing at 600°C., gave the result; shown in the: lower section of Fig. I. In the present work the investigation of the properties of these materials has been extended by a study of the tensile deformation characteristics in moderately longtime tests at 600°, 700' and 800°C. after quenching from various solution temperatures. In addition, some metallographic studies have been made to correlate with the deformation tests, and to obtain information on the quasi-binary system cobalt-Fe2Ti. The material, very kindly furnished by the Westinghouse Electric and Manufacturing Co. in the form of hot-swaged rods of 3/16-in. diameter, analyzed as shown in Table 1. The alloys, when originally made up,' were based upon an iron-titanium compound, Fe3Ti, as indicated by the work of

Jan 1, 1941

By Carll H. Samans, Charles R. Austiuon

It has been known for several years1 that certain alloys of the Konal type, containing commercial cobalt (99.32 per cent Co and 0.42 per cent Ni) and varying amounts of ferrotitanium, exhibit very high tensile strengths at 600°C. However, their proportional limits and yield pints are relatively low. published data' for the alloys quenched in water from 950°C. and then tested at 600°C. are summarized in the upper section of Fig. I. Similar specimens that were aged at 650°C. for 72 hr., after quench and prior to testing at 600°C., gave the result; shown in the: lower section of Fig. I. In the present work the investigation of the properties of these materials has been extended by a study of the tensile deformation characteristics in moderately longtime tests at 600°, 700' and 800°C. after quenching from various solution temperatures. In addition, some metallographic studies have been made to correlate with the deformation tests, and to obtain information on the quasi-binary system cobalt-Fe2Ti. The material, very kindly furnished by the Westinghouse Electric and Manufacturing Co. in the form of hot-swaged rods of 3/16-in. diameter, analyzed as shown in Table 1. The alloys, when originally made up,' were based upon an iron-titanium compound, Fe3Ti, as indicated by the work of

Jan 1, 1941

By C. S. Matthews, H. M. Girner, C. D. Williams, M. J. Edwardson, H. R. Parkison

Quantitative interpretation of electric logs requires knowledge of formation temperature. In this paper, methods are developed for computing changes in formation temperature caused by circulation of mud during drilling operations. The basis of the method is the mathematical solution of the differential equation of heat conduction. The solution of this equation is presented in a series of graphs. These graphs are used to determine formation temperature disturbance at various radii for arbitrary mud circulation histories. Example comparisons with field results show reasonable agreement. It is concluded that, in general, the temperature disturbances caused by circulating mud are small beyond 10 ft from the wellbore but are quite significant near the wellbore. INTRODUCTION Quantitative interpretation of electric logs requires knowledge of the formation temperature in order to establish the resistivity of the formation water with accuracy. To determine the formation temperature, the temperature disturbances produced by circulating drilling mud must be evaluated. -The objective of this investigation was to develop a method for the numerical determination of these temperature disturbances at any distance from the wellbore as a function of time. The first step was to solve the differential equation describing the temperature behavior in the formation during and after mud circulation. This solution was used to calculate a series of curves relating temperature disturbance to shut-in time for various circulating periods. An "exact" method for computing formation temperatures with the use of these temperature-disturbance plots is described, and the results of an application of this method to a well in Montana are presented. Procedures for approximating formation temperatures are also discussed. BASIC EQUATIONS AND ASSUMPTIONS With the assumptions that (1) cylindrical symmetry exists, with the borehole as the axis, (2) heat flow is 1. The formation can be treated as though it is radially infinite and homogeneous in extent, as regards heat flow. 2. The presence of mud cake can be disregarded. 3. The effect of heat generated by bit action is negligible. 4. After mud circulation ceases, the rate of radial heat flow at the wellbore is negligible and is assumed zero for purposes of calculating temperature change with time. These assumptions are believed to be reasonable because of the agreement achieved between calculated and measured borehole temperature in a well, to be discussed later. Further, the agreement at the wellbore indicates that temperatures in the formation were also approximately correct. since it is the formation temperatures that determine wellbore temperature after ceasing circulations SOLUTION OF THE DIFFERENTIAL EQUATION AND ITS APPLICATION The solution of Eq. 2 for the temperature behavior during and after a single period of mud circulation is

By J. M. Woodall

GuAs crystals which have been grown in quartz boats by the horizontal Bridgman method in the pvesence of Ga20 vapov have beetz found to have carrier and donor distributions which do not correspound to those expected from simple dopant seg-vegation during directional freezing; Instead, the carrier distribution is determined by the heat-trentnzent history of the crystal, while the donor distribution, zohiclz is principally due to silicon, is fixed by the pozuth rate, the geo)tlet.ry of the crystal growth vessel, and tlze initial Ga20 pressure. WHEN semiconducting materials are made into doped crystals by the normal freezing method,&apos; they usually exhibit doping variations along the growth axis. If a) there is no dopant diffusion in the solid, b) the dopant is distributed uniformly in the melt, and c) the distribution coefficient, k, does not vary with composition, then the doping variation along the growth axis is represented by the equation: where C is the doping level in the solid at a point where a fraction g of the original liquid has frozen, and Co is the mean concentration. When the dopant is either a singly ionized shallow donor or shallow acceptor, C also represents the carrier concentration. Even though this equation accurately describes the dcping profiles of a large number of normal freeze systems, there are several special systems for which Eq. [I] does not apply. One such system is the horizontal Bridgman method for preparing oxygen-grown GaAs crystals using quartz vessels. Several workers2"* have shown that GaAs crystals grown by the horizontal Bridglnan method using quartz vessels are generally contaminated with silicon in concentrations in excess of 5 < 10lG atoms per cu cm. This contamination is ascribed to a reaction: occurring at the walls of the crystal-growth vessel which liberates silicon into the melt and Ga2O vapor. It has been shown4 that this reaction, and, hence, the silicon contamination, can be suppressed by the addition of oxygen to the crystal-growth apparatus. It is the purpose of this paper to describe a special apparatus capable of yielding single crystals of GaAs grown in the presence of oxygen and to describe both the kinetics of silicon suppression in this system and the relationship between the carrier concentration profile and the silicon concentration profile. EXPERIMENTAL-CRYSTAL GROWTH A schematic diagram of the apparatus used in the oxygen addition experiments is shown in Fig. 1. The most important features of this apparatus are: a) the use of a sand blasted quartz boat, h) a quartz rod of length 1, with a hole of cross section A, that is placed near the boat to limit the free space volume V, over the melt during the growth, and c) the temperature gradient at and near the solid-liquid interface. Sand blasting the boat is necessary to prevent wetting of the melt. The quartz rod retards the diffusion of the GazO vapor away from the melt to the colder portions of the ampoule. A crystal is prepared by first loading a 5.5-in. boat, which has been cleaned in aqua regia, with 40 g of 99.9999 pct Ga along with 1 to 8 mg of Ga203 powder. GazO3 is a convenient source of oxygen since it reacts with gallium at the melt temperature to form Ga20 vapor, the species which apparently controls the suppression of silicon contamination. The loaded boat, the quartz rod, and the 99.9999 pct As are placed in the ampoule as shown in Fig. 1. Generally, GaAs seeds were not used since most of the unseeded growths resulted in monocrys-tals. The ampoule is evacuated to 10-5 Torr and sealed off. The GaAs melt is synthesized by placing the ampoule into a two-zone horizontal Bridgman furnace. The two zones are separated by several sandwiched layers of -in. Fibre-Fax board drilled with holes slightly larger than the OD of the ampoule. This causes a very large temperature gradient between the two zones, which is necessary for single-crystal growth. The two-zone furnace is mounted on a stand fitted with a roller bearing which allows uniform motion of the furnace in a horizontal direction. A uniform velocity of the stand is achieved by the use of a windlass device which winds up a wire attached to the stand. Movement of the solid-liquid interface is accomplished by fixing the position of the ampoule and moving the stand. Growth rates investigated in this experiment were between 0.4 and 1.2 in. per hr. The composition of the melt is fixed by maintaining an arsenic reservoir at 618°C. The stand is moved away

Jan 1, 1968

Boundary and general corrosio~z rates for higkpurity alutninum were ~rzeasured irz 16 pct HC1 at sJmllow penetrations (< 25 p). The rates for several high-angle random tilt boundaries, several [001] synzmetrical tilt boundaries, a 54-deg [010] twist, and a 15-deg randorn tw~st boundary were one-fourth to one-third higher than that of the (001) surface used as reference. Boundary attack was slower for 23 and 37-deg [001] tilt boundaries and a 16-deg [010] twist boundary. The corrosion rate for a (111) surface was roughly om-third higher than for (001) and was thus about as high as the corrosion rate of the fastest boundaries. The boundary attack did ?lot appear to parallel the variatiorz of boundavy energy. The signvicance of the anisotropy of corrosion was discussed.

Jan 1, 1966

By E. C. Bohlen, H. l. Burghoff

THE work reported in this paper was carried out to supplement the existing information concerning directional properties and recrystallization textures of annealed brass sheet and strip. These characteristics are of direct interest when the forming and drawing properties of such material are being considered. Among those who have made contributions in this field are Bass and Glocker;1 Bauer, Göler and Sachs;2 Phillips and Samans;3 Pratt;4 Price;5 Cook;6 Richards;7 Brick;8 and Brick and Williamson.9 These investigators have found, in general, that in brass strip that shows directional variations in properties, tensile strength has a minimum value and elongation has a maximum value at 45° to the rolling direction. The most pronounced directional properties have been found in material given the greatest reductions in rolling followed by high annealing temperatures. Recrystallization texture of brass has been variously reported as (113)[112], (001)[100], and a combination of (110)[115] and traces of the primary rolling texture, (110)[112]. The directional studies have been very informative, but actual tests appear to have been confined to material in its final condition. Tests at intermediate stages have received little attention although previous history of some materials has been partly considered. Perhaps the most comprehensive investigation was made by Cook,6 who studied the directional properties of 70-30 brass strip for which the final and penultimate, or next to the last, anneals and the final reductions were varied. He found that, for any given combination of penultimate anneal and final reduction, the tendency toward the development of directional properties was reduced as the temperature of the final anneal was decreased. In addition to drawing cups and making tensile tests of the finished material at various angles to the rolling direction, he measured the frequency and the angles of twins in grains for several specimens. Plots of his twin counts showed directionality for the materials that produced eared cups. TEST MATERIALS AND EQUIPMENT For this investigation, one commercial heat of 68-32 brass was cast in the form of bars for cold-rolling, 13 ½ in. wide and 1 ½ in. thick. The analysis was as follows: 68.83 per cent copper, 0.04 per cent lead, 0.01 per cent iron, 31.12 per cent zinc (by difference). The bars were so processed to the final thickness, 0.020 in., as to obtain on this thickness all possible combinations of the variables listed below except those involving the sequence of 84 per cent penultimate reduction and 84 per cent final reduction: I. Penultimate reductions of 37 per cent, 50 per cent and 84 per cent; 2. Penultimate anneals at 800°, 900°, 1050° and 1200°F.; 3. Final reductions of 37 per cent, 50 per cent, 69 per cent and 84 per cent;

Jan 1, 1942

By P. G. Shewman, T. L. Wilson

Using published surface-diffusion (D,) data and published sintering equations, it is shouln that surface difusion should dominate the neck-growth stage of intering for all materials in which D, has been measured (six metals and A1as). Also, grain boundary diffusion can be expected to contribute appreciably to shrinkage and possibly to neck growth below some critical temperature of the order of 70 pct 01- the absolute melting temperatuve. In view of the widespread conclusion in previous sintering work that volume diffusion dowzinates neck gvowth, experiments were conducted using spherical copper powders to test this conclusion. Scaling studies on neck growth at 950°and 1020°C clearly demonstrated that suyface diffusion dorninates. Kinetic studies on shrinkage gave more equivocal results that indicated an increasing role of&apos; grain boundary transport at lower temperatures. Five diarszeters from 100 to 300 u were used in the scaling sludy and a temperature range of -650&apos; 10 950 C was covered in the shrinkage studies. All experiments were conducted in dvy hydrogen. In 1949, Kuczynski published his now classic paper on the determination of the transport mechanism in sintering from the time laws of neck growth. In the interim, these laws have been applied to many systems and slightly modified by several authors. Essentially all these authors concluded that, for crystal- line materials, the dominant transport mechanism in neck growth is volume diffusion. This stems from the observation that the neck radius increases about as t"5 and that the activation energy approximates that for lattice diffusion. A related but independent series of studies stems from Mullins&apos; rigorous analysis of the growth of the groove formed where a grain boundary meets a free surface." xperimental work stemming from this analysis has shown that for each crystalline material studied (Au, Ag, Cu, Ni, Fe, Pt, Al2O3) surface diffusion was clearly the dominant transport mechanism for groove widths up to the order 10 to 20 p. The ratio of the quantity of material being carried by lattice diffusion to that carried by surface diffusion increases linearly with the groove width, so surface diffusion is dominant for all widths under 10 to 20 u. The analysis of the relative contributions of surface and volume diffusion to grain boundary grooving, and to neck growth in sintering, shows that they are quite similar. Thus, using the available surface-diffusion data and the approximate equations of Kuczynski, or the more rigorous recent equations of Nichols and Mullins, 3 it can be shown that the small necks between particles must grow almost entirely by surface diffusion. The purpose of this study was to re-examine the basis for the conclusion that the neck-growth stage of sintering proceeds by volume diffusion. Using spherical copper powders, of several different diameters, precise experimental measurements were made of both neck growth and shrinkage. Application of Herring&apos;s scaling laws to the neck-growth data clearly indicated that neck growth occurred by surface transport, even though the neck radius increased as or Using the recent analysis of Mullins and Nichols as well as published data on surface diffusion, it is shown that the observed time law, as well as actual rate of neck growth, can be satisfactorily explained by a surface-diffusion mechanism.

Jan 1, 1967

By C. E. Mills

Studies of ground movement and subsidence resulting from mining operations cover a broad field. It is also a very important consideration and one that eventually affects nearly every mining operation of any extent. The damage to surface buildings, removal of mine surface plants and replacements of main hoisting shafts must reach an astounding expenditure were these cost figures available over a period of years. Were the subject one of mathematical formula and dependent only on the angle of draw of the walls or country rocks, the problem would be relatively simple. Consideration must be given to depth and extent of workings; structural conditions of the orebodies and enclosing country rock; physical properties of these same rocks, including schistosity, bedding, jointing, slips, dikes, faults, and other structural weaknesses. The method of mining, extent of openings, supporting pillars, and amount of moisture or water underground are other pertinent factors. With such a large number of variable factors, it is apparent that the subject of subsidence is one that must be based largely on experience and results at other mines where conditions are somewhat comparable. In presenting this paper, it is the intent to describe the progressive results of past ground movements at the United Verde, to bring out physical conditions largely responsible for this movement, but to refrain from theorizing on the ultimate extent of subsidence resulting from future mining operations. Geology and Structure1 The ore deposits of the United Verde are of the massive sulfide, schist-replacement type. A structural anticline formed by the intrusion of diorite between bedding planes of steeply dipping and severely folded greenstones and porphyry localized the deposit of sulfide. The mineralized zone is of great horizontal extent varying from 200,000 to 400,-000 sq. ft., and extends from the surface to the lowest levels at a steep dip of from 50° to 75. The irregular interfingering of the sulfide with

Jan 1, 1934

By J. D. Rice, P. L. Wearden, W. L. Hensou

Solutions to the unsteady-state partial water-drive reservoir performance problem can be obtained through the use of analogue computers or high-speed electronic digital computers. The solutions that have previously been resolved for use on digital computers, however, demand a knowledge of the aquifer parameters. Generally, the analogue computers now in use do not require this knowledge. A solution is presented herein where the aquifer performance, expressed in terms of difference equations, is related to the reservoir performance as expressed by the modified Scbiltbuis material-balance equation. A numerical procedure for a medium-sized digital computer also is presented in which a solution to the set of equations defining the aquifer and reservoir performance is obtained and the aquifer parameters (permeability and sand thickness) are automatically optimized while simultaneously matching the known pressure behavior. Predicted pressure behavior can be calculated using rates from any assumed future production practice. The procedure provides an output format which presents the cumulative, incremental and average rate of natural water influx, the per cent gas-cap expansion, the calculated reservoir pressure, the measured reservoir pressure, and the difference between the measured and calculated pressures. Results of a test problem are presented in comparison with results obtained by the Bruce Analyzer, Ohio Oil Co. &apos;s Pace General Purpose Analogue Computer, and Sun Oil Co.&apos;s Single-Pool Electronic Reservoir Analyzer. These results indicate that unsteady-state reservoir perlormance for a single-pool system can be adequately simulated by a numerical method employing a digital computer and that the special-purpose analogue computer can be supplanted by this method. INTRODUCTION The numerical approach to the unsteady-state partial water-drive reservoir performance problem heretofore has been limited in that solutions have been resolved only for certain fixed parameters. Also, prior to the advent of high-speed electronic digital computers in the last few years, calculations were so tedious and time-consuming that they ordinarily were neglected, or some other means of obtaining the solutions were used. The analogue approach had been used for obtaining solutions to the transmission-of-heat problem and, consequently, means were developed for applying the electrical analogue to the unsteady-state reservoir performance problem. Bruce submitted a paper for AIME publication in Sept. 1942, in which he described an electronic device (now called the Bruce Analyzer) for analyzing the water-drive performance of any reservoir, based on either steady or unsteady-state flow characteristics. 1 Sun Oil Co. adopted the analogue approach in 1949 and now has two special-purpose high-speed electronic reservoir analyzers in use.2,3 Two main features of Sun&apos;s analyzers are (1) the high repetitive rate of reproducing the entire history of reservoir performance cyclically a number of times per second, and (2) the elimination of the necessity of knowing the properties of the associated aquifer. Since the advent of larger and faster digital computers, the possibility of incorporating this second feature into a numerical approach appeared feasible. Previous work has been done and material published covering the application of numerical methods to the behavior of the pressure with respect to time at any point in an associated aquifer? However, the aquifer parameters must be known from some source. The material presented in Ref. 4 has been used to a great degree in developing the numerical method described herein. DIFFERENTIAL EQUATION AND BOUNDARY CONDITIONS The problem of simulating the performance of a reservoir and the associated aquifer is to determine the characteristics of the aquifer such that the

By S. S. Marsden, S. A. Khan

Externally generated foam was injected continuously into short porous media. Both flow rate and pressure drop were measured. Liquid saturation was determined by electrical conductivity. Foam yuality I, expressed as the ratio of gas volume to total volume, was varied from 0.70 to 0.96. As measured with a modified fann VG Meter, apparent viscosity of this foam µa decreases with increasing shear rate but usually falls within the range of 50 to 500 cp. At a given shear rate, µa increases almost linearly with I-. When measured with a Bendix Ultraviscoson, kinematic pa is independent of V but absolute pa increases with T from about 3 to 8 cp. The effective permeability -apparent viscosity ratio ke/µa decreases almost linearly with V for porous media of high permeability, but the rate of decrease becomes less for tighter ones. The relative permeability-apparent viscosity ratio kr/µa us V data does not fall on a single line. The kr/µa ratio increases with liquid saturation in the porous medium and with surfactant concentration. Estimates of pa for foam in porous media vary from 30 to 100 cp. INTRODUCTION Although research on the development of a foam-drive, oil recovery process has been going on for almost a decade, most of the significant publications have appeared within the last several years. This illustrates well the rate at which interest in this process is accelerating. Bond and Holbrook 1 were the first to describe the use of foam to improve oil recovery in their patent of 1958. They proposed that an aqueous foaming agent slug be injected into the formation and that this be followed by gas to produce a foam in situ. Fried 2 studied the injection of foam into porous media which had already been subjected to conventional gas or water drives and found that gas could be used to drive a foam bank which would, in turn, displace additional oil in the form of an oil bank. He attributed the increased oil recovery to the high effective viscosity of foam flowing in porous media. His microscopic observations showed the importance of foam generation and regeneration within the porous medium. By injecting both air and aqueous surfactant solution, Bernard3 generated foams within the porous medium in which oil displacement was being studied. In a separate empirical test, he also measured the dynamic foaming characteristics of the same surfactants in water and/or oil. With some exceptions and for the seyen surfactants studied, there seems to be a qualitative relationship between the efficiency of liquid rlisplacrment and the dynamic foaming testtsed. This relationship was not consistent enough to eliminate the necessity of actual foam flood tests in porous media for surfactant selection. In a study basic to gas storage in aquifers, Bennett4 described the displacement of brine by foam in consolidated porous media. Among other things, he stated that the ability of a surfactant solution to foam is more important than the stability of its foam. The presence of a foam bank between the displacing air and the displaced brine improved both breakthrough and ultimate recovery. In a continuation of this work Kolb5 attributed the great reduction in surfactant solution production rate as displacement by air progressed to a decrease in relative permeability to gas. These several effects reported by both Bennett and Kolb can all be attributed to the high apparent viscosity of foam which was obviously flowing in the porous media. Bernard and Holm6 observed that gas permeability in the presence of foam was much less than in the absence of foam when both were measured at the same gas saturations. This reduction in permeability was proportionately greater for more permeable sands and sandstones than for the less permeable. Viscosities of the surfactant solution and air were used for their calculations rather than apparent foam viscosities. The foam stability increased with decreasing permeability, which was probably due to the natural regenerative properties of porous media, and the permeability reduction increased

Jan 1, 1967

By Donald W. Scott, Nathaniel Arbiter, A. C. Richardson

This paper describes the application of amine flotation to a specific problem—that of increasing the grade of magnetite concentrates derived from an iron ore requiring extremely fine grinding for mineral liberation. Experiments conducted on an iron ore from Wisconsin had shown that concentrates containing 60 to 62 per cent iron and 12 to 14 per cent silica could be produced by magnetic separation. The residual silica occurred as quartz and hornblende, either entrained or locked with magnetite. Most advantageous utilization of the concentrate, however, necessitated that the silica content be reduced to about 5 per cent, equivalent to an iron content of 67.5 per cent. It had been demonstrated that tabling of the magnetic concentrate removed sufficient quartz and hornblende to yield an acceptable concentrate, but disadvantages inherent in tabling dictated that flotation be investigated as a substitute. The goals set for the flotation investigation were: (I) the production of concentrates of about 68 per cent iron content from the magnetic concentrate; (2) an iron recovery of about 85 per cent of that in the feed to flotation; and (3) minimum reagent cost. Both batch and continuous flotation tests were employed; the former, to establish the procedure and the latter to verify it. Although the data were obtained on a specific ore, and with a commercial application in view, it is believed that they have a bearing on other problems where amine flotation is being used or is anticipated. Samples Two samples, designated "(minus 100-mesh magnetic concentrate" and "minus 150-mesh magnetic concentrate," were used for the batch experimental work. They differed only in the degree to which the crude ore was ground prior to magnetic separation. They were stored moist in steel drums in quantities sufficient for all the experimental work reported. This procedure had the advantage of allowing all tests to be made on common samples, but had the disadvantage that the individual flotation samples, because of the difference in storage time, were subject to various stages of surface alteration. Previous work had indicated that common samples were desirable for the batch studies, and it was decided that if these data appeared sufficiently promising the effect of surface alteration could be checked best by continuous tests. The size distributions and the assays of the samples are given in Table I. The minus 150-mesh magnetic concentrate, on which most of the flotation tests were made, assayed 60.9 per cent iron, 13.3 per cent silica, and 0.016 per cent phosphorus. The minus 325-mesh portion represented 78.I per cent of the sample by weight, and assayed 67.9 per cent iron. Thus, the insoluble, mainly silica, was concentrated

Jan 1, 1947

By Donald W. Scott, Nathaniel Arbiter, A. C. Richardson

This paper describes the application of amine flotation to a specific problem—that of increasing the grade of magnetite concentrates derived from an iron ore requiring extremely fine grinding for mineral liberation. Experiments conducted on an iron ore from Wisconsin had shown that concentrates containing 60 to 62 per cent iron and 12 to 14 per cent silica could be produced by magnetic separation. The residual silica occurred as quartz and hornblende, either entrained or locked with magnetite. Most advantageous utilization of the concentrate, however, necessitated that the silica content be reduced to about 5 per cent, equivalent to an iron content of 67.5 per cent. It had been demonstrated that tabling of the magnetic concentrate removed sufficient quartz and hornblende to yield an acceptable concentrate, but disadvantages inherent in tabling dictated that flotation be investigated as a substitute. The goals set for the flotation investigation were: (I) the production of concentrates of about 68 per cent iron content from the magnetic concentrate; (2) an iron recovery of about 85 per cent of that in the feed to flotation; and (3) minimum reagent cost. Both batch and continuous flotation tests were employed; the former, to establish the procedure and the latter to verify it. Although the data were obtained on a specific ore, and with a commercial application in view, it is believed that they have a bearing on other problems where amine flotation is being used or is anticipated. Samples Two samples, designated "(minus 100-mesh magnetic concentrate" and "minus 150-mesh magnetic concentrate," were used for the batch experimental work. They differed only in the degree to which the crude ore was ground prior to magnetic separation. They were stored moist in steel drums in quantities sufficient for all the experimental work reported. This procedure had the advantage of allowing all tests to be made on common samples, but had the disadvantage that the individual flotation samples, because of the difference in storage time, were subject to various stages of surface alteration. Previous work had indicated that common samples were desirable for the batch studies, and it was decided that if these data appeared sufficiently promising the effect of surface alteration could be checked best by continuous tests. The size distributions and the assays of the samples are given in Table I. The minus 150-mesh magnetic concentrate, on which most of the flotation tests were made, assayed 60.9 per cent iron, 13.3 per cent silica, and 0.016 per cent phosphorus. The minus 325-mesh portion represented 78.I per cent of the sample by weight, and assayed 67.9 per cent iron. Thus, the insoluble, mainly silica, was concentrated

Jan 1, 1947

By K. K. Clark, W. H. Somerton

The feasibility of reducing pressures needed to fracture formations by heating the borehole intensively has been investigated on a laboratory scale. Reductions in fracture pressures of heated Bandera, Berea and Boise sandstone cores were observed at various confining pressures, simulating reservoir stress conditions to a depth of 5,000 ft. Both permeable and impermeable borehole boundary conditions were tested. Three heating conditions were used in the tests. One group of samples was heated in a furnace to a temperature of 600C, cooled to room temperature., and then tested for fracture pressures. Two other groups of samples were heated with a borehole heater to maximum borehole wall temperatures of 625 and 792C, then cooled and tested. In all cases, heated samples showed substantial reductions in fracture pressures compared to unheated samples. The higher temperature borehole heated samples showed the greatest reduction, amounting to 70 per cent in the extreme case. In actual application to wells, it was concluded that fracture pressures may be reduced by 20 to 50 per cent by intensive borehole heating before fracturing. INTRODUCTION Hydraulic fracturing of oil and gas wells is an accepted and effective technique for increasing well productivity in many areas, but is notoriously unsuccessful in other areas. The technique becomes less interesting for production stimulation purposes when excessive fracture pressures are necessary. Formations which do fracture but require high pressures, probably form horizontal fractures. There is good evidence to indicate that some formations do not fracture at all, but yield plastically under high pressure. Thus, any technique which will make formations easier to fracture or will reduce fracture pressures is potentially interesting to petroleum producers. Horizontal fractures generally occur in planes of weakness, such as bedding planes, and at pressures equaling or exceeding the effective overburden stress. In the unusual case where planes of weakness do not exist, a slightly higher pressure must be applied to overcome the tensile strength of the rock. In general, high fluid-loss fracturing fluids are conducive to the formation of horizontal fractures.1 Vertical fractures, when they do occur, are initiated at pressures generally lower than overburden pressure and are favored by low fluid-loss fracturing fluids or impermeable boreholes. The pressure necessary to create a vertical fracture in an impermeable, elastic medium can be predicted from the so-called "thick-walled cylinder" equation: Pf = 2 or+ st.............(1) where pf = fracture pressure or = radial stress st = tensile strength of medium. This equation indicates that to fracture it is necessary to overcome a tangential compressive stress, induced by and equal to two times the radial confining stress, plus the tensile strength of the medium. If the above equation held strictly true for rocks, very little could be done to reduce fracture pressure. The tensile strength of the rock might be reduced somewhat, but any change in st would be small compared to the magnitude of the tangential stress at reasonable subsurface depths. Laboratory tests have shown that actual fracture pressures exceed values predicted from Eq. 1 by factors of 1.4 to 28.6.1,2 Eq. 1 thus does not properly describe the

Jan 1, 1966

By Matti J. Saarivirta

Two new precipitation hardening copper-base alloys, Cu-1.5pct Ti-2.5 pct Sn and Cu-1.5 pct Ti-2.5 pct Sn-0.4 pct Cr were developed. High strength and medium conductivity are obtained by solution annealing and subsequent heat treatment. Combination of solution annealing, cold working, and heat treatment increases the strength further. Good elevated temperature strength and ductility makes these alloys superior to copper-beryllium-cobalt alloys. A considerable amount of research work is being done throughout the world to develop new and improved copper-base alloys. In many cases, the object is to develop alloys having a combination of high electrical and thermal conductivities, and high strength. The problem is complicated by the fact that any alloying element added to increase strength, invariably decreases conductivity. Among the few commercial precipitation hardening type copper-base alloys, the Cu-Be-Co alloys are best known. These alloys are used in many applications that require good spring characteristics cornbined with high strength and moderately high electrical conductivity. They can be formed readily after solution annealing, then heat treated to obtain high strength and conductivity. Because of the relatively high cost of the Cu-Be-Co alloys, considerable research has been aimed at developing new lower cost alloys having similar properties. As far as is known today, the binary Cu-Ti alloy is the only one whose properties are

Jan 1, 1962

By George K. Foster, Charles D. Borror

THE Jeffrey mine of the Canadian Johns-Manville Co., Limited, is in the town of Asbestos, situated approximately 100 miles northeast of Montreal and about the same distance southwest of Quebec, in Richmond County, Quebec. Mining operations were started in 1881 on outcrops on a hill, as a side-hill cut, followed by a second and third cut. This development was the forerunner of the present large open-pit operations, the mine now ranking as the largest openpit asbestos mine in the world. Operations were first carried on by hand, then by horsepower and later by stem cableways. By 1924 the derrick spans, 2000 ft. or more long, became unwieldy. To overcome this, and also to eliminate hand labor as much as possible, steam shovels and railroad haulage were introduced. The steam shovels were replaced in 1928 by larger electric shovels of the full-revolving type. THE ORE BODY The ore body is a serpentinized peridotite rock mass. The chrysotile fibers form a network of veins throughout, varying from microscopic width to two or more inches measured across the veins (Fig. I). These veins may be continuous for a few or many feet; they may increase or decrease in width within a few feet. The veins in which the fibers occur perpendicular to the veins are known as cross fiber. Those in which the fibers lay parallel to the veins are known as slip fiber. The cross fibers are of better quality, and more in demand. The majority of the fiber [ ]

Jan 1, 1946

By Albert Wiggin

THE copper-bearing sulphide ores from the mines in Butte, Mont., which are for the most part concentrated at the Boston & Montana duction Works in Great Falls and at the Washoe Reduction Works in Anaconda, contain the following minerals of economic value: Chalcocite, Cu2S; enargite, Cu3AsS4; cupriferous pyrite; bornite, Cu3FeS3; covellite, CUS; tetrahedrite, 4 CuS2Sb2S3; and tennantite, Cu8AsS7;. All of the ores carry a high percentage of pyrite. Many of the above sulphides are argentiferous and also carry from 10 to 20 cts. per ton in gold. The gangue is quartz and highly altered granite, with sphalerite and galena and more rarely barite and hubnerite as accessory minerals. An average chemical analysis of the second-class ore concentrated at Great Falls and Anaconda would be as follows: Copper 3.2 to 3.4 per cent. Silver 2. 3 to 3.0 oz. per ton. Gold 0.0-1 to 0.15 oz. per ton. Si02.. 55 to 60 per cent. FeO 12 to 15 per cent.. Sulphur 12 to 1.5 per cent. Al2O3, S to 10 per cent. CaO 0.5 to 0.8 percent. As203, 0.5 to 0.6 percent. Lead 0.2 to 0.3 percent. Before describing the Great Falls flow sleet as installed, at Anaconda, a brief history of the Great Falls concentrator will be given, including a description of the various concentrating machines and systems which have been tested in the search for a flow sheet which would give a higher recovery of copper.

Jan 8, 1913

By G. H. Matheson, J. M. W. Mackenzie

The flotation rate of coal has been studied using a continuous laboratory flotation cell and a multiple exposure photographic technique. The effects of particle size, reagent additions and cell turbulence on the flotation rate of coal have been investigated. The results have been analyzed in terms of current theories of particle bubble encounter and adhesion. The rupture forces which occur during particle bubble encounter have been shown to have an important effect on the flotation rate of coarse coal particles. The flotation of coal is a time dependent process, and in order to obtain a complete understanding of the operation it is necessary to determine the kinetics of the process. In coal flotation, the flotation rate and the associated values of cell productivity in terms of tons per kilowatt-hour and tons per cubic foot of cell volume are of greater importance than in most other mineral flotation operations. The reasons for this are associated with the low unit value of coal and the relatively high cost of coal flotation compared with other coal cleaning processes. An important aspect of coal flotation kinetics is the design of coal flotation cells. The cells used in many coal cleaning operations are often replicas of those used for the treatment of sulfide ores and are not necessarily suitable for the treatment of coal washing pulps, which usually contain a higher percentage of coarse and floatable material than the sulfide pulps for which the cells were designed. This disadvantage of many coal flotation cells has been recognized by Russian engineers who, by the addition of baffles to their subaeration coal flotation cells have increased the cell capacity by 100%. Investigation of the variables which influence flotation kinetics and cell productivity are, therefore, important to the coal industry where flotation is the only accepted method of cleaning the fine (-1/2mm) coal. The kinetics of the flotation process have been investigated in detail by Schumann10 who developed a continuous flotation cell which permitted the study of flotation under steady state conditions. This technique has been used by Gaudin et a1.,6 Brown and Smith and recently by Jowett and Savfi.7 The latter authors have developed a refined mathematical treatment for interpreting the results of continuous laboratory tests. Attempts have also been made to study flotation kinetics using conventional batch testing techniques. The experimental difficulties, however, and the problems of determining the order of the flotation rate process have made this technique of dubious value. A summary of the proposed rate equations for batch testing and the difficulties associated with this technique is given by Brown and Smith. 2 The experimental techniques described above are concerned with the rate of production of froth product. However, several authors, notably Sutherland, 11 Bogdanov1 and Philippoff, 9 have analyzed flotation

Jan 1, 1963

By D. B. Kibler

Pill Florida hard-rock field extends from Suwanee and Columbia Counties in northwest Florida to south of Croom, Florida, in Hernando County this area is approximately 100 miles long and varies from 2 to 30 miles 1n width Florida hard-rock phosphate was discovered at Hale Springs, about one mile northwest of the town of Dunnellon Marion County, in the year 1888, by Albertus Voight who lived within a few hundred yards of the spring Soon after this discovery there was a great influx of land speculators and wildcat operators into the vicinity of Dunnellon A few years later phosphate was found in Alachua, Levy, Citrus and Hernando Counties, and a great number of small crude plants were built from Newberry, Alachua County, all the way to Croom, Hernando County Phosphate was found in many places as "outcrops " Looking for outcrops was the first method used by the early prospectors in searching for deposits Several years passed before any systematic method of prospecting was used EARLY MINING The early method of mining hard-rock phosphate was with picks and shovels, wheelbarrows, mules and wagons The pick-and-shovel method was used altogether until about 1900, when some of the larger operators began to use railroad-type steam shovels of from 1/2 to 1-yd capacity Picks and shovels, with negro labor loading the phosphate ore (called "matrix") into wooden side-dump skip-cars, was continued until about 1907 From the discovery of hard-rock phosphate until approximately 1905, overburden was removed with mules and scrapers At some places, the overburden was loaded into side-du nip skip-cars by negro laborers and the cars were then pulled up an incline with a steam hoisting engine The maximum depth of overburden that could be economically removed by hand labor mules and scrapers was approximately 15 feet About 1905 one of the companies erected a producer-gas powerhouse near Dunnellon and generated its own electricity and about the same time the larger companies began using hydraulic methods for the removal of overburden From the year 1888 through the year 1939, approximately 75 companies were operating at one time or another in the hard-rock territory, on approximately 500 locations The hard-rock deposits are more irregular and have higher mining costs than the pebble-rock deposits, therefore they have not been competitive in the domestic market, but because of the higher grade of the hard rock it is in demand for the export trade Discovery of phosphate outside of the United States has made it increasingly difficult in recent years for the hard-rock companies to survive, so today only three companies are operating These

Jan 1, 1941

By M. Cohen, R. T. Howard

It has long been realized among metallurgists that a fast, reliable method for the quantitative determination of the percentage of microconstituents in an alloy would be of great benefit in studies of equilibrium and transformation in the solid state. For example, Polushkinl has shown that the compositions of two coexisting phases in a binary system at a given temperature may be calculated very simply with the aid of two alloys lying in the two-phase field if the relative amounts of the two phases in each alloy can be determined. Recently, Grange and Stewart2 have traced the course of the austenite-martensite reaction in a series of commercial steels by making visual estimates of the percentage of martensite formed as a function of cooling temperature. The correlation of mechanical properties with structure, a subject of wide-spread current interest, is likewise dependent upon quantitative microanaly-sis. Yet, there are very few investigations described in the metallurgical literature, wherein methods of quantitative microscopy are employed. Usually, the relative amounts of the microconstituents are estimated in a qualitative or semiquantita-tive way. The authors were faced with this problem some time ago in studying the kinetics of austenite decomposition. Several aspects of this research could not be treated satisfactorily by other quantitative tools, such as specific volume,&apos; magnetic,6 dila-tometric, electrical resistance7 or x-ray measurements.a It became necessary to find an impersonal quantitative method that could be applied to microstructures. Fortunately, it was noted that geologists and petrographers had coped with quantitative microscopy to a considerable degree in their attempts to evaluate the mineral contents of rocks. A number of excellent articles were found on this subject, and since they appear to be unknown generally to many metallurgists, the first part of the present paper is concerned with a review of the literature in some detail. With this survey as a background, the authors have adapted the so-called methods of point-counting and lineal analysis to metallography, as described in the second part of the paper. Austenite-martensite structures were selected for illustration not only because they are important in many ways, but because such fine intermixtures are notoriously difficult to estimate visually. Literature Survey Perhaps the earliest work on quantitative microscopic analysis goes back to Delesse9 (1848) who proved mathemati-

Jan 1, 1948

By M. Cohen, R. T. Howard

It has long been realized among metallurgists that a fast, reliable method for the quantitative determination of the percentage of microconstituents in an alloy would be of great benefit in studies of equilibrium and transformation in the solid state. For example, Polushkinl has shown that the compositions of two coexisting phases in a binary system at a given temperature may be calculated very simply with the aid of two alloys lying in the two-phase field if the relative amounts of the two phases in each alloy can be determined. Recently, Grange and Stewart2 have traced the course of the austenite-martensite reaction in a series of commercial steels by making visual estimates of the percentage of martensite formed as a function of cooling temperature. The correlation of mechanical properties with structure, a subject of wide-spread current interest, is likewise dependent upon quantitative microanaly-sis. Yet, there are very few investigations described in the metallurgical literature, wherein methods of quantitative microscopy are employed. Usually, the relative amounts of the microconstituents are estimated in a qualitative or semiquantita-tive way. The authors were faced with this problem some time ago in studying the kinetics of austenite decomposition. Several aspects of this research could not be treated satisfactorily by other quantitative tools, such as specific volume,&apos; magnetic,6 dila-tometric, electrical resistance7 or x-ray measurements.a It became necessary to find an impersonal quantitative method that could be applied to microstructures. Fortunately, it was noted that geologists and petrographers had coped with quantitative microscopy to a considerable degree in their attempts to evaluate the mineral contents of rocks. A number of excellent articles were found on this subject, and since they appear to be unknown generally to many metallurgists, the first part of the present paper is concerned with a review of the literature in some detail. With this survey as a background, the authors have adapted the so-called methods of point-counting and lineal analysis to metallography, as described in the second part of the paper. Austenite-martensite structures were selected for illustration not only because they are important in many ways, but because such fine intermixtures are notoriously difficult to estimate visually. Literature Survey Perhaps the earliest work on quantitative microscopic analysis goes back to Delesse9 (1848) who proved mathemati-

Jan 1, 1948