Search Documents

By H. B. Pulsifer

One of the most common basic open-hearth furnace products is a simple carbon steel with a carbon range from 0.05 to 0.15 per cent. The material is widely used for sheets, tubes, bars, wire and the innumerable special objects of secondary fabrication. The properties of the material vary over wide ranges, depending on the more exact composition and details of manufacture or treatment that affect its structure. The present paper is a review of those properties and structures that have been found by studying this steel as used in the cap screw industry. At first glance this might be thought a narrow application of the steel, but, since the industry uses the material in the cold-worked, annealed and heat-treated conditions, the title of the paper may be excused for its comprehensiveness. Yet, in studying the wide ranges of properties and structures that preclude a more specific title, there can be no suggestion of completeness or finality. Even a summary of a few years' work is no more than a preliminary survey of a field that will be fertile in scientific data and industrial products for many years to come. An outline of the structures will be given first, then a list of the previous contributions that are at hand and finally some details of the work and related problems, especially concerning this low-carbon steel in the surface-hardened condition. Wire Used in Manufacture of Cap Screws The wire that is used for making cold-upset and roll-threaded cap screws has been cold-drawn from hot-rolled rods that were pickled and limed. The common sizes used in the industry range from 0.185 to 0.750 in. dia., the exact diameters depending on the plant practice and having the usual tolerances of 0.002 in. for the smaller sizes and 0.003 in. for the larger sizes. The carbon range, by pit analysis, is usually between 0.07 and 0.12 per cent. Manganese should be within the usual 0.30 to 0.50 per cent. range. Sulfur rarely exceeds 0.045 per cent. and phosphorus seldom exceeds 0.030 per cent. Silicon is usually below 0.03 per cent. but in the silicon-killed steels may be in the customary 0.10 to 0.25 per cent. range. Rimmed steel is not considered most suitable for cap screws that are cold-headed or for parts that are to be surface-hardened.

Jan 1, 1931

By D. J. Schmatz, H. I. Aaronson, H. A. Domian

Diffusion kinetics in disordered hcp Cd-Mg alloys have been investigated by means of the Kirkendall effect and concentration-penetration curves determined with an electron-microprobe analyzer. Self-diffusion coefficients of both species were determined at the three marker compositions obtained, averaging 27.6, 46. 7, and 78.1 at. pct Mg, by means of the Darken analysis. These coefficients were then corrected for the unequal and concentration-dependent partial molar volumes of the two elements with the Balluffi analysis, and for the vacancy flux effect by the Manning analysis. The latter correction reduced the Balluffi correction produced larger changes in the self-diffusiv-ities; neither, however, produced statistically significant changes in the Do's or the H'S. The most striking result of this investigation is that at all three compositions and at all temperatures studied both the uncorrected and corrected self-difjusivities of magnesium are higher than those of cadmium. The Cd-Mg system is the first one found in which the higher melting, lower vapor pressure element diffuses more rapidly. Both an empirical correlation due to Toth and Searcy and considerations of the atomic mechanism of diffusion indicate that this anomaly is probably due to a comparatively low value of the activation energy required for a magnesium atom and a vacancy to exchange sites, perhaps occasioned by the higher compressibility of magnesium atoms. KIRKENDALL effect studies have been previously reported for only two hcp solid solutions: the E phase of the Zn-Cu system1 and the a phase of the Cd-Hg system.' In neither investigation were the marker-movement studies supplemented with the concentration-penetration curve determinations necessary to evaluate self-diffusivities by means of the atano and the Darken analyses. The present program was undertaken to obtain both types of data on a hexagonal solid solution in order to provide more detailed information relevant to the mechanism of diffusion in this type of lattice. The Cd-Mg system was chosen for this study because the disordered solid solution extends across the entire phase diagram at temperatures above 253"c5 and the substantial difference in the melting points of the component pure metals promised that marker movements would occur at reasonably rapid rates should the diffusivities of the two species be as unequal as might be anticipated. The experimental convenience of the relatively low melting points of cad-miun and magnesium and the availability of extensive and accurate activity data6 (required for application of the Darken analysis) were additional reasons for selecting this alloy system. Since the anisotropy of diffusion is not large in either pure cadmium7 or pure magnesium,' the diffusion couples were prepared from polycrystalline components. The presence of a well-defined texture in the couples—the c axis of individual crystals tended to be normal to the diffusion direction— however, provides a fair degree of crystallographic definition to the data obtained. The principal (and entirely unexpected) finding of this investigation, that magnesium, the high-melting low-vapor pressure element, diffuses more rapidly than cadmium, in contradiction to a broad range of results in fcc and bcc alloys, as well as in the previously studied hcp alloys,172 makes the self-diffusivity determinations of immediate interest in understanding the origin of this anomalous result. EXPERIMENTAL PROCEDURE The cadmium (Belmont Smelting and Refining Co.) and magnesium (Dow Chemical Co.) used in this study were both of 99.99 pct purity. Alloys containing 51.0 and 65.6 at. pct Mg were prepared from these materials by melting under a MgC12-base flux in a high-purity graphite crucible. These alloys were subsequently hot-worked and then homogenized in a helium atmosphere at temperatures close to their solidus points. Sandwich-type diffusion couples of the type g/d/g were prepared from the pure metals by solid-state diffusion. Two-piece alloy couples of Mg/65.5 at. pct Mg (Mg/gCd) and Cd/51.0 at. pct Mg (Cd/CdMg) were welded by a liquation technique. The individual components of both types of couple were initially cylinders 1.27 cm in diam and in length; the ends of these cylinders were machined accurately flat and parallel. For both welding techniques, the pure cadmium cylinders and the alloys were chemically polished in a mixture of 40 pct ethyl alcohol, 40 pct hydrogen peroxide (30 pct conc), and 20 pct nitric acid,g while those of pure magnesium were polished in a solution of 10 pct nitric acid in ethyl alcohol.' Immediately afterwards, both metals were rinsed in freshly distilled acetone, and then in similarly purified methanol.' The Mg/Cd/g couples were assembled in a carefully cleaned stainless-steel welding fixture, in which a screw operating through a self-centering arrangement permitted a controlled pressure to be exerted upon a couple prior to welding.'' Tungsten marker wires 0.005 cm in diam were placed at the d:g interfaces of some of these couples, and imbedded in the couples during the application of pressure. As soon as a couple had been assembled, the welding fixture was inserted into a Pyrex capsule containing a packet of zirconium chips at each end. The capsule

Jan 1, 1967

By PHILIP N. MOORE

PHILIP NORTH MOORE was born on July 8, 1849, at Connersville, Ind. His father, a civil engineer, was descended from Henry Moore who came from Ireland in 1773 to live in Washington, Pa. Through his mother, Philip Moore was descended from John North, who came to America in 1635 and settled in Connecticut. The story of Mr. Moore's life as told by himself is given on pages 373-386 of T. A. Rickard's "Interviews with Mining Engineers." He studied at Miami University, where he gained the degree of A.B. in 1870, and A.M. in 1873. In 1920 his alma muter conferred on him the honorary degree of LL.D. He, as a special student, was a member of the class of 1872 at the School of Mines of Columbia University.

Jan 1, 1930

By Paul T. Benson

MOST important of the various departments of a custom smelter, so far as the financial welfare of the plant and the confidence of shippers are concerned, is that responsible for correct weights, accurate moisture sampling, and the obtaining of control samples that are strictly representative of the lot of ore from which they come. Treatment rate schedules are based on the metal content of ores received, reduced to dry weight. These rates must be low enough to keep the ship- per from taking his business else- where and still must allow the smelter a profit. Assay results, likewise, must satisfy the shipper, but if they show too high a metal content for the ore they represent, the smelter will actually lose money. It is always considered, and constant checks through umpire assays prove, that laboratory results are closely correct, so the bur- den of the plant profit and loss and the satisfaction of the shipper rest squarely upon the sampling department.

Jan 1, 1936

By L. O. Millard

Stockpiles in the minerals industries serve a wide variety of purposes. Usually they are for surge between stages of processing, for a dependable plant feed in anticipation of delays, or to provide for single or double shift mining in conjunction with round-the-clock milling. Often surge piles are necessary to insure a uniform feed to continuous process equipment where the material is received as an intermittent or variable flow. Extensive use is made of stockpiling for the primary purpose of blending. The significant fact about all stockpiling of bulk materials is that storing and reclaiming are two separate and distinct operations and they may present widely different problems in the selection of methods and tools.

Jan 10, 1959

By Eugene Guccione

Australia could eventually become a major world supplier of uranium oxide-but how quickly that happens depends on the outcome of a highly complex and emotional battle among different special interests.

Jan 1, 1977

By E. G. Banks

THIS paper is presented in the belief that metallurgists and chemists will be interested in the practice of grinding in tube-mills in connection with stamps, especially since the records of working here given extend over a lengthy period of time (since May, 1905). The ore from the Waihi mine-more especially that produced in the upper levels-contains a large proportion of hard, chalcedonic quartz, and the gold exists in an exceedingly fine state, conditions which necessitate very fine crushing in order to ob¬tain a high extraction of the precious metal. Before the introduction of tube-mills at the 90-stamp Waihi mill, it was found necessary to stamp through 40-mesh (1,600 holes per sq. in.) woven wire-screens, having a fairly high discharge. The pulp then graded

Jan 1, 1907

By E. Ray Webb

A interest to geologists and to mining and petroleum engineers is a laboratory method for determining the dip and strike of sub- surface structures, as well as the direction of fault planes traversing them. The information is derived by making use of the magnetic properties of borehole cores which must show visible representations of bedding or fault planes. Complete knowledge of these factors aids greatly in the successful exploitation of both ore and petroleum deposits.

Jan 1, 1940

By ARCHIBALD DOUGLAS

AT various times during the past quarter century proposals have been made that the basic Federal mining law of 1872 be repealed or amended, and that in its place a new and simpler law be enacted to provide for the entry upon, working, and the taking up of claims on the unallotted Federal mining lands in our western states and in Alaska. Serious discussion and study have been given such proposals but little has resulted there from, except perhaps a lively interchange of opinion and the conclusion that though the Apex law of 1872 is in many ways highly unsatisfactory and frequently a fomenter of strife and trouble, it still bids fair to remain with us. Under this act a greater part of the non-ferrous mining industry of the United States has developed. With all its short-comings it is the legal bridge that has carried over the innumerable caravans of adventurers and prospectors who explored our mining frontiers. For without any amendments of substance this act has for fifty-eight years been the guide in the location of our western Federal mineral claims and has stood unchanged during the most important period of our mining history. While Federal and state acts and amendments have been ground out by thousands and tens -of thousands the mining act of 1872, with a :strange tenacity, has remained as constant as the Rock of Gibraltar, and under it states, mining districts, and local customs have developed different codes for its application but its fundamentals have been unaltered. "Use doth breed a habit in a man"; until now the application of the law of 1872 has become a second mining nature.

Jan 1, 1930

By Joseph B. Perry, G. M. Kirwan

MAGNESITE is found in 22 California counties, but many of the deposits are too small or too impure to be of commercial value. Several of substantial size and quality were entirely exhausted by wartime operation. At present, three properties comprise the only known workable deposits in the state. Of these, the Western mine and the Patterson mine have been known and worked for many years, and have been described in considerable detail in various publications, therefore need only brief mention here, because of their proximity to the Bald Eagle mine. The latter, recently developed, is unusual in type of ore deposit, plant design and operation, as well as products made, and very little has been written concerning it. WESTERN MINE The Western mine, 32 miles south of Livermore, Calif., was formerly operated by C. S. Maltby. It has been a consistent producer for many years.1 The ore is of amorphous variety, occurring along fracture zones in serpentine. The veins vary greatly in width, the average being perhaps 8 ft., with the maximum indicated in one early stope of 40 ft.; 2 ft. is considered the minimum for economical mining. The strike of the veins is predominantly north and south, with dip to the west varying from 40º to 75 º. Walls are well defined and as a rule firm and easily supported. Veins range in length from a few hundred feet to 1000 or more. Their maximum vertical extent is about 350 ft., but many run less. Early mining consisted of open-cut and glory-hole work on the larger outcrops. This was followed underground by a modified shrinkage system, the waste and low-grade horses being removed by hand sorting on the tramming levels and transported to surface dumps. Filled-stope mining is used now, in order to eliminate the handling of waste, which has

Jan 1, 1938

By H. J. Rose, J. J. S. Sebastian

When coal is stored under ordinary conditions, progressive changes take place in its chemical and physical properties. These changes are largely caused by the reaction of atmospheric oxygen with the coal substance. Although this "oxidation" or "weathering" occurs slowly in the case of high-rank coals, it is nevertheless a matter of considerable importance, since even a small amount of oxidation may affect the value of coal for carbonization purposes. Coal storage is a necessity at all carbonizing plants. In normal times there are about 5,000,000 tons in storage at by-product coke ovens and gas retorts in the United States, as compared with an annual throughput of about 75,000,000 tons. In other words, the average coal reserve at such plants is slightly less than one month's supply. However, owing to the cost of storage and recovery, coal is usually left in stockpile for as long a time as the management thinks advisable. Storage for six to eight months is common practice and is, in fact, a necessity at certain plants which obtain their coal by water routes that are closed during winter months. Modern by-product coke ovens operate continuously, and they are not cooled down from the time that they arc put into operation until they are shut down for rebuilding—perhaps 20 years later. This continuous operation is imposed by silica-brick construction and high operating temperatures. It is therefore obvious that coke plants must at all times maintain an adequate supply of stored coal, in order to prevent a failure in supply from any cause whatever. Thus when strikes or other emergencies threaten, abnormally large coal stocks are accumulated and held at coke and gas plants. Many of these plants have been forced, at some time or other, to use coal that has been stored for several years. Such coal may fail to coke at all, or it may produce a dirty appearing, weak coke of reduced value. The yields of salable by-products may also be distinctly lowered. However, it must not be assumed that slight oxidation or heat effects are always injurious. Certain high-volatile coals produce a stronger, blockier

Jan 1, 1930

By Arthur Notman

YEAR ago, the Committee on Mineral Economics ventured to predict a more realistic attitude by the public toward the folly of seeking to have more by making less under the guidance of the Blue Eagle. A unanimous decision of the Supreme Court of the United States has now laid that embattled bird to rest. De rnortuis nil nisi bonum. In spite of dire predictions of disaster to follow its early demise, the metal industries and many others have improved substantially. One could name many indications of that improvement, and on the strength of stock-market activities might assume

Jan 1, 1936

By Byron E. Eldred

(Pittsburg Meeting. March, 1010.) GENERALLY speaking, the practical study of combustion has been made mainly from the stand-point of the steam engineer. This. narrow view-point has left open a large field for scientific research on the application of combustion in other arts, where the conditions of heat-utilization are widely different from those presented in the steam-generator. The great economic importance of the boiler and the ease of measuring its performance, together with the comparative uniformity of conditions in the steam-generator, is, probably, quite largely responsible for the practical neglect of the study of the use of fuels in other arts save only on the basis of their thermal value. Yet these other arts show quite plainly that a thermal-value basis alone is Dot sufficient. For example, in burning lime, under ordinary conditions of firing, a cord of wood will do as much work as a ton of coal, though the latter affords more than twice the number of heat-units. Similar results are evidenced in burning brick, in the roasting of certain ores, in reheating billets, and in many other arts where heat is to be applied over extended areas to fragmental masses of more or less refractory materials. In these arts much is to be gained by a careful study of the application of the heating-agent in the form of the long flame, and in the production of the heat in contact with, or in direct proximity to, the object to be heated. Of necessity, in boiler-practice, combustion cannot be maintained in actual contact with, or in close proximity to, the object to be heated. Speaking in a general way, heat is imparted from burning bodies to things to be heated in two ways : directly, by radiation, and indirectly, by transfer of the sensible heat of hot gases by convection or contact; by conduction from the hot uses. Both ways are utilized in boiler-practice-directly, by

Jun 1, 1910

By Wm. E. Milligan

LEAD stocks at the beginning of 1943 were comfortable when compared with those of other base metals such as copper, zinc and tin. This situation was early recognized by W.P.B. and other Governmental agencies and every effort was made to encourage the substitution of lead for these latter metals in all essential uses. Despite this apparently healthy condition, lead was not denied participation in the various measures inaugurated by the Government to relieve metal shortages. Thus in the Mexican trade agreement, effective Jan. 20, the tariff on two important classes of lead importss was halved. Similarly, in the setting up of B quota premiums, a B base was allotted to lead, with all pro¬duction above this figure receiving an additional payment of 2.75c. per lb., or a total payment of 11.75c. per lb. At about the same time it was announced that all quota transactions would be based upon the lead content as shown by the smelter settlement sheets. This basis was 86 percent of the lead content for all ores shipped to custom milling plants and 95 per cent for ores and concentrates shipped to custom smelting plants. The importance of this action can be appreciated when in the Coeur d'Alene it was estimated as equivalent to a 5 per cent increase compared to the previous base.

Jan 1, 1944

By Augustus Locke

WHY should I, a geologist, be coming before you to talk about finding ore? Certainly, the great discoveries of the past have not been made by geologists, but by men of very different tastes and training. If, in the year 1800, the course of ore discovery could have been foreseen, there would have been no reason to put it into the hands of geologists or other men of technical preparation. It was not geologists but explorers, Indian fighters, prospectors, manual laborers, and hardy financiers, who initiated the American mining industry. Then why this association of geological technique with ore finding? Why this feeling that the way to find ore is to apply to the problem what we call geo- logical principles? Well, to put it broadly, the old method has run out on us. It no longer works. Or, to put it another way, the cost of finding ore by the old method has mounted so high that one old district after another has become, practically speaking, dead, and various other old districts that are still going apparently at full strength are actually beginning to limp, and, with the cost of discovery mounting yearly, to fear, more than they will acknowledge, that the end is approaching.

Jan 1, 1926

By R. Walker, R. J. Anslow

Today at Tampa we see the end results of a team effort: A vital link in an intermodal transportation system, the link that enables the unit-train concept to be employed with full effectiveness and the link that improves the economics of water transportation systems. Two new phosphate transfer complexes with a multi- million ton annual capacity are in operation in Tampa, Fla. Revolutionary in concept, these companion installations represent a total investment in the Tampa Bay area of $18.5 million.

Jan 1, 1970

By R. Schuhmann, J. Th. Overbeek, P. L. De Bruyn

THE technique of concentrating valuable minerals from lean ores by flotation depends upon the creation of a finite contact angle at the three-phase contact, mineral-water-air. If the mineral is completely wetted by the water phase, contact angle zero, there is no tendency for air bubbles to attach themselves to the mineral. However, when the contact angle is finite, the surface free energy of the system, water-air bubble-mineral particle, can be diminished by contact between the bubble and the particle, and if not too heavy the mineral will be levitated in the froth. With a few exceptions, all clean minerals are completely wetted by pure water. Thus the art of flotation consists in adding substances to the water to make a finite contact angle with the mineral to be floated, but to leave the other minerals with a zero contact angle. The contact angle concept and experimental measurements of contact angles have played important roles in flotation research for several decades.'-" Nevertheless, there remain unanswered some basic questions as to the scientific significance of the contact angle and the nature of the processes by which flotation reagents affect contact angles. The contact angle is a complex quantity because the properties of three different phases, or rather of three different interfaces, control its magnitude. Considering the interfaces close to the region of ternary contact to be plane, the relation among the contact angle and the three binary interfacial tensions is easily derived. The condition for equilibrium among the three surface tensions, Fig. 1, or the requirement of minimum total surface free energy leads to Young's equation, Eq. I: ysa — ysl = yLA cos 0 [1] According to this equation, the contact angle has one well-defined value. Actually it is found in many experiments that the value of the contact angle depends on whether the air is replacing liquid over the solid (receding angle) or the liquid is replacing air (advancing angle). The receding angle is always the smaller of the two.4 Two explanations have been offered for this experimental fact. According to some investigators,5-8 roughness of the surface causes apparent contact angles that are different for the receding and the advancing cases although the actual local contact angle may be completely determined by Eq. 1. The other explanation involves the hypothesis that the solid-air interface after the liquid has just receded is different from the same interface when no liquid has previously covered it.1,4 Adsorption of constituents of the air or liquid might play a role here. In this discussion the difference between advancing and receding contact angle will be neglected and plane surfaces where Eq. 1 describes the situation will be considered. But there is still a fundamental obstacle to the application of Young's equation. The surface tension of the liquid (rla) can easily be determined, but the two surface tensions of the solid (rsa and ySL) cannot be measured directly. Eq. 1, however, is not without value. By contact angle measurements it is possible to establish how ysl — ysl varies with the addition of solutes to the liquid phase. Also, Eq. 1 affords a convenient starting point for calculating net forces and energy changes involved in the process of bubble-particle attachment.1,2 . If for the moment surface tension of the liquid (yLa) is considered a constant, an increase in ysa — ysL, will tend to decrease the contact angle. A decrease in ySA — ysl, corresponds to an increase of the contact angle. In cases where ySA — ySL > yLa the contact angle is zero; it will only reach finite values when ysa — ysa has been decreased below YLA. Thus on the basis of Young's equation and contact angle measurements alone, it can be learned how flotation reagents affect the difference Ysa — ysl, but no conclusions can be drawn as to the effects of reagents on the individual surface tensions ysa, and ysL, not even as to signs or directions of the surface tension changes resulting from reagent additions. A quantitative relationship between the surface tension or interfacial tension and the adsorption occurring at a surface or an interface is given by the Gibbs equation, which for constant temperature and pressure reads dy = — 2 T, du, [2] where dy is the infinitesimal change in surface tension accompanying a change in chemical potential

Jan 1, 1955

By E. S. Shaw

Utah continues as a very unimportant factor in oil and gas production. During the year 1933 there were no developments of noteworthy significance. There were no completions of either producers or dry holes during the year. The only commercial production in Utah has been from the five fields listed in Table 1 and mentioned briefly in the following paragraphs. Virgin Field.—Oil was first discovered in 1907 in a well drilled in sec. 13, T.41S., R.12W. Of the first 15 wells drilled, all but three were failures. In 1920 production from four wells from 550 to 600 ft. deep was about 20 bbl. per day. San Juan Field.—The majority of drilling in this area was done during the years 1908 to 1911. Probably the first commercial well in the field was that drilled in NW.$i sec. 6, T.42S1 R.l9E., in 1909. Farnham Dome.—The discovery well was drilled by the Utah Oil Refining Co. in April, 1923. A number of years later a second well was drilled by The Carbon Dioxice a mica1 Co., the present operator, which markets the gas in the manufacture of "dry ice" and allied products. The eslimated production, as indicated in Table 1, includes 500 million cubic feet estimated to have been lost while drilling the discovery well. Cisco Dome.—The discovery well was drilled by The Utah Oil Refining Co. in November, 1924. The Crystal Carbon Co. markets the gas in the manufacture of carbon black. Ashley Valley Dome.—The discovery well was drilled by the Utah Oil Refining Co. in April, 1925. The Uintah Gas Co. markets the gas in Vernal, Utah, for fuel. Woodside Structure.—In February, 1924, gas was discovered in a well drilled by Utah Oil Refining Co. in sec. 12, T.l9S., R.l3N., on the Woodside structure. This gas is reported to contain an appreciable amount of helium. It is being held as a helium reserve by the United States Government. Salt Valley Structure.—The test of the Utah Southern Oil Co. in sec. 31, T.23S., R.21E., on the Salt Valley structure has been shut down for some time at 6120 ft. This test has passed through more than 5000 ft.

Jan 1, 1934

By G. D. TRANT

HOT metal is commonly transported from the blast furnace to the open hearth by one or the other of two general methods: (1) by hot-metal ladles, usually in conjunction with a stationary mixer, or; (2) by means of mixer-type ladle cars, taking the place of both the hot-metal ladles and the stationary mixer. In both cases, the use of transfer ladles for charging the metal into the open-hearth furnaces is necessary. The American Rolling Mill Co. at its Middletown division, adopted hot metal practice on. June 2, 1928. The pig iron is produced' in a .blast furnace about 11 miles from the open-hearth furnaces, and is trans- ported in Pugh-type mixer cars having a capacity of 150 gross tons each. Three cars are in service and handle the delivery of hot metal to the pig machine and the open-hearth furnaces. The capacity of the blast furnace is 550 tons and casts are made every four hours.

Jan 1, 1929

By J. L. Christie, W. R. Webster, R. S. Pratt

Since the delivery of our paper on Some Comparative Properties of Tough-pitch and Phosphorized Copper,1 a new brand known as "oxygen-free high-conductivity copper" (brand OFHC) has become available to consumers. It was thought desirable to make a comparison between the properties of this material and those of the materials covered by our original paper and its discussion. Preliminary tests had indicated some notable differences. A billet of oxygen-free high-conductivity copper was taken from regular production. A chemical analysis of the particular billet was not made, but the producer of the material has given as typical the analysis shown in Table 1. The

Jan 1, 1933