Search Documents

By Robert Bakish

VARIOUS aspects of structure-sensitive corrosion of single crystals and polycrystalline aggregates of Cu,Au have been presented in papers by the author, in association with W. D. Robertson. Prompted by some observations in the course of these studies, a new approach to the problem was undertaken. Results of these new experiments are reported here. Thin slices, less than 2 mm thick, were prepared from single crystals 3.5 mm in diam grown by the Bridgman technique. The crystals were homogen- ized for 300 hr at 850°C. Crystals with no deformation, crystals deformed in tension to the yield point, and crystals deformed 20 pct in excess of the yield point were used. Crystals of several different orientations were studied. Slices were immersed for one month in 2 pct aqueous solution of FeCl3 and, subsequent to this immersion, were subjected to bending. Immersion and bending were carried out at room temperature. The size and geometry of the crystals did not permit accurate data on the loads involved. A most unexpected result was obtained in the process of bending these slices of Cu3Au crystals normal to the (110) plane. Completely brittle be-

Jan 1, 1958

By Edward E. Hicke, Charles A. Stickels

The dihedral angle of liquid-lead inclusions in solid nickel has been measured as a function of temperature from 371 to 816 C at zero pressure. and as a function of pressure up to 50,000 psi at 317 and 593 C. Thermodynamic expressions are derived for the temperature and pressure coefficients of interfacial tensions in this system. A method is presented for obtaining relative tempmature and pressure coefficients from dihedral-angle data, and the resulting values are used in conjunction with the thermodynamic relations to calculate excess properties of the solid-liquid interface. Defining the position of the solid-liquid interface by the condition that the excess concentration of lead is zero, the excess concentration of nickel and the excess entropy at the solid-liquid interface are: where y(593) is the interfacial tension of the nickel grain boundary saturated with lead at 593C and zero pressure. These values are considered reliable to within a factor of two. While similar calculations are not possible for the nickel grain boundary, it is shown that the expwimental results imply that the excess concentration of nickel at the boundary and the excess entropy of the boundary are negative. THE temperature and composition dependencies of interfacial tensions in metal systems have been reported by several authors in the last 15 years.'-' No measurements of the effect of pressure on inter- facial tensions in metals have been reported, although measurements made on nonmetallic gas/liquid and liquid/liquid systems suggest that a measurable effect should exist.6-l2 The purpose of these experiments was to determine the influence of temperature and hydrostatic pressure on dihedral angles in the Pb-Ni system. The equilibrium dihedral angle is expressed as a ratio of interfacial tensions by2: where 8 is the dihedral angle, yGB is the Ni-Ni grain boundary tension, and SL is the solid Ni-liquid Pb interfacial tension. Three sets of ex- periments were run to determine: a) the effect of temperature from 371" to 816°C on the dihedral angle at zero pressure; b) the effect of pressure up to 50,000 psi on the dihedral angle at 371° and 593°C. THERMODYNAMICS The properties of interfaces of most direct concern are the interfacial tension, excess concentrations of various components at the interface and the excess entropy of the interface, S°. These quantities are defined following Gibbs. Consider an interface separating phases a and 0. Construct two surfaces C, and C such that all properties of phase a remain uniform up to C, and all properties of phase 0 remain uniform up to C. The region between C, and Cp is the interfacial region. Let a "dividing surface", D, be constructed in the interfacial region such that it passes through all points "similarly situated with respect to the condition of the adjacent matter."l3 Surface D divides the interfacial region into a portion a' adjacent to phase adjacent to phase . Let a closed curve, C, enclose an area A in D. Erect normal lines to D along C; these lines and the surfaces C,, Cp, and D then enclose volumes V and V' in the two halves of the portion of the

Jan 1, 1964

By D. J. McAdam, R. W. Mebs

The technical cohesive strength of a metal means, not the interatomic forces, but the technically estimated resistance to fracture. An example of such resistance to fracture is the so-called "true" breaking stress of a tension-test specimen, the breaking load divided by the sectional area at fracture. According to the prevalent view,8 the technical cohesive strength of a metal. in any particular state as regards prior mecharlical treatment and heat-treatment, is determined by a limiting value of the algebraically greatest principal stress. In two previous papers by one of the authors, evidence was presented to indicate that the technical cohesive strength of a metal cannot be represented by a single stress value, but that it comprises an infinite number of values corresponding to the infinite number of possible combinations of the principal stresses. The technical cohesive strength thus comprises an infinite number of technical cohesion Limits, each representing a specific stress combination at fracture. In the same papers, evidence was presented that plastic extension causes a continuous increase in the technical cohesive strength. Such a variation is not in accordance with the prevalent view that plastic extension first increases, then decreases, the technical cohesive strength.' In this paper, as in the previous papers,14.15 the algebraically greatest principal stress will be designated S1, the least principal stress will be designated 33, and the intermediate principal stress will be designated S². The technical cohesion limit under polarsymmetric tension (S1 = S2 = S3) will be termed the "disruptive stress," and the cohesion limit under unidirectional tension (S2 and S3 = o) will be termed the "severing stress."l4, .l5 The yield strength of a metal, according to the generally accepted theory, may be represented by a constant value of the shearing-strain energy, and hence by a constant value of the sum of the squares of the three principal stress differences. In the second of the previous papers,15 however, evidence was presented that the limiting yield stress decreases with increase in the volume stress, the algebraic average Of the three principal stresses.* This in fluence of the volume stress becomes prominent only in the field of triaxial tension. In the two previous papers,".'5 diagrams were presented to show the variation of the technical cohesion limit, yield stress, and ultimate stress with the combination of principal stresses and with plastic extension. Those diagrams and the resultant • Any stress system ma? be resolved into a polarsymmetric stress causing pure volume strain and a combination of pure shearing stresses. which cause no change of volum

Jan 1, 1945

By P. Farrar, H. Margolin

The Ti-Pb diagram was investigated in the region 0 to 58 pct Pb and from 500°C to liquidus temperatures. Three reactions were encountered: I—ß?a+Ti Pb at 725 10°C; 2—ß+L?Ti4Pb at 1305+ 10°C; and 3—the possible eutectic L-+Ti,Pb and y between 1200" and 1300°C. LEAD-RICH alloys have been investigated by Nowotny and Pesl,' who used sintered compacts and studied the region from 37.5 to 100 pct Pb by X-ray diffraction analysis. The only phase found in addition to titanium and lead was the hexagonal compound Ti Pb. Alloy systems of lead with metals of the transition group, such as iron, chromium, tungsten, cobalt, nickel, or manganese, generally show little liquid or solid solubility.' Craighead et al.,3 however, indicated that lead is soluble in a and ß titanium to at least 2.1 pct. They also found that approximately 50 pct of the lead added was lost during the arc-melting of Ti-Pb alloys. In the present investigation, are-melting also was used to prepare Ti-Pb alloys and similarly large lead losses were encountered. Experimental Procedure Alloy Preparation: Considerable difficulty was encountered in the melting of the Ti-Pb alloys and a number of experiments were performed before the method described was developed. Alternate layers of lead and titanium were wrapped with titanium sheet and compacted. This "sandwich" was annealed at 300" to 350 °C and was melted according to the procedure described by Cadoff and Nielsen.' Using a low current, 150 amp, and an argon atmosphere, four to eight 10 to 20 sec melts were made on each alloy, with the button being turned over between each melt to insure homogeneity. In the high lead range, the preliminary sintering was found to be of doubtful value and was eliminated. In the region above the nominal composition of 70 wt pct Pb, the alloys prepared in this manner always consolidated into two phases. The outside appeared to be composed entirely of lead and the inside was a Ti-Pb alloy. In order to determine whether this phenomenon was caused by a miscibility gap, master alloys with a nominal composition of 40 wt pct Pb were machined and mixed with various percentages of lead sheet. This mixture was compacted and melted in the same manner as the other alloys. Although these alloys were not homogeneous, they did not show the layering that was observed

Jan 1, 1956

By Harmon D. Nine

DISCONTINUITIES in the strain vs cycles to failure (S-N) fatigue curves have been reported for polycrystalline materials by Porter and Levy for copper,&apos; by Benham and Ford for mild steel,&apos; and by Williams and Stevens for 18/5 stainless steel.3 However, the considerable scatter of the points for polycrystalline materials have made a statistical analysis of the data necessary to confirm the discontinuities. By using oriented single crystals of high-purity material and low grown-in dislocation content, the reproducibility has been improved to a degree which makes statistical analysis unnecessary and clearly shows discontinuities in the S-N curves. A recent publication4 reports an abrupt change of slope in the S-N curve for ( 100) axially oriented copper single crystals fatigued in torsion. The reported discontinuities in the S-N curve, along with a different mode of failure in the two branches of the curve, have been interpreted as being due to two different amplitude-dependent mechanisms. Further work on copper single crystals of (111) axial orientation has now been completed which supports the existence of an amplitude-dependent change in the mechanism of fatigue. In the present study torsional-fatigue experiments were performed at room temperature in air on (111) axially oriented single crystals. The crystals were grown and prepared as reported in Ref. 4. Two different methods of growing the crystals also discussed in Ref. 4 produced crystals of two different perfections: Type I with dislocation density of >l06 per sq cm and Type I1 with dislocation density of <l05 per sq cm. In accordance with the accepted hypothesis that crystal flaws are primarily responsible for the scatter of fatigue lifetimes, particularly at low amplitudes, the values for the three lowest amplitudes for Type I crystal are believed to be uncertain. They are marked in braces in Fig. 1. On the other hand, at amplitudes above a surface shear strain (SSS) of *0.003, the data for both types of crystals are in agreement. Most remarkably the S-N curve for torsional fatigue of (111)-oriented single crystals is composed of three segments separated by rather large discontinuities, Fig. 1. Metallographic and X-ray measurements indicate that the lower branch corresponds to the low-amplitude (F) region of the (100) copper single-crystal results as discussed in Ref. 4, and the two upper branches correspond to the high-amplitude (H) region. The lower discontinuity in the (111) S-N curve and metallographic evidence give further support to the hypothesis that different mechanisms of failure operate for high and low strain amplitudes. Reference to the resolved shear stress diagram, Fig. 2, shows that the highest stressed systems in

Jan 1, 1965

By WILLIAM BOWIE

THE development of the isostatic idea during the last century would make an interesting paper in itself. But the various steps in the development have been covered in a number of papers and books which are readily available. Therefore this short paper should not give space to. the historical phases of the subject. Isostasy is really an old idea, but it is only in the last few decades that it has taken on any great prominence or importance in the study of earth phenomena. It is really remarkable how closely Dutton&apos; sensed the isostatic principle 40 years or more ago. His general principles of isostasy as outlined by him have stood the test of time and fit in closely with the general ideas held today. It would seem, however, that some of his views with regard to the application of isostasy to geological processes must be modified or abandoned.

Jan 1, 1930

By L. A. Cowan

IF the elements of personality be those characteristics in which humans differ, and if this definition be applied to the purchasing department for the Climax operations in Colorado, it must he concluded that this department has no distinguishing traits that would give it a departmental personality different from that possessed by the similar department of any progressive mining enterprise. Or, one may go further by stating that the rudimentary functions of any purchasing practice employed principally in the acquisition of maintenance, repair, and operating supplies are much alike, whether or not the industry involved be mining or milling. However, in the fact that the principal purchases of a mining company are materials for maintenance and repair and consumable operating supplies lies that essential characteristic which differentiates mining and milling purchasing functions from those of the manufacturer, the fabricator, or the ordinary processor.

Jan 1, 1946

By Samuel S. M. Chan

The magnetic susceptibilities of some ores and the major rock formations of the Precambrian Belt Supergroup in the Coeur d&apos;Alene mining district were determined both in the laboratory by the use of the Gouy method and in the field with a Bison susceptibility unit. Trace element analysis of the same group of rock samples was also made using the atomic adsorption technique. Results of this preliminary study indicate that some correlation exists between the magnetic susceptibilities and the various rock formations. This may be useful for regional mapping and mineral exploration.

Jan 1, 1974

By Joseph E. Pogue

THERE are two methods employed in the development of oil pools. The older and dominant method is one in which the primary object is the protection of the underground deposit from drainage through competing wells, and considerations of efficiency of extraction and cost of production are subordinated thereto. The newer and less prevalent method is one in which maximum efficiency and minimum cost are the first objectives and developments to these ends may proceed undisturbed by the exigencies of competitive drainage. The second method has developed mainly in pools under single ownership and the term "unit operation" has come to be applied to this procedure. A single ownership, however, is not essential to the method, for unity of operation may be achieved by agreement under split ownership, or even by a concert of enlightened purpose. There are examples of unit operation where neither the ownership nor the management is a unit, but merely where unity of procedure has been attained, as is the case of the Yates pool. .Throughout this paper unit operation is used in its broad sense without implying sole ownership or single management, although unit operation is more conveniently attained where these conditions are present.

Jan 1, 1930

By R. S. Dean

PROCESSES for the direct production of iron and steel from ores are hardy perennials, and new processes and revivals of old ones are continually being brought to the attention of the investing public if not to the attention of metallurgists. Direct production of iron and steel is so simple that it offers a fertile field for the promoter. Unfortunately in this way direct processes have acquired a bad name, not always deserved, with conservative capitalists and metallurgists. Direct processes cannot, except in special instances, be looked upon as a substitute for any single operation in present iron and steel practice but must be considered, as one link in an entirely new chain of metallurgical process from ore to finished steel. Thus it is, in my opinion, inadvisable to consider the use of sponge-iron processes as a means of treating ore of ordinary blast-furnace grade to produce open-hearth feed. In time I think it will be found equally inadvisable to smelt iron-ore concentrates in the blast furnace.

Jan 1, 1935

By Brian F. Dyson

The surface tensions at 1550°C of some Fe-S alloys (in the range 0.008 to 0.052 wt pct S), Fe-Sn alloys (0.31 to 48.4 wt pct Sn), Fe-P alloys (0.038 to 2.38 wt pct P), Fe-Cu alloys (2.15 to 22.8 wt pct Cu), and Fe-1 pct C-S alloys (0.005 to 0.076 wt pct S) along with the surface tension of the base iron have been measured by the sessile-drop method. A mean value of 1754 dynes per cm was found for the surface tension of the base iron. Sulfur was found to be highly surface-active, the surface-tension results being in quantitative agreement with existing data. Tin and copper were found to be less surface-active than sulfur while phosphoms was completely nonsurface-active. The surface tensions of Fe-1 pct C-S alloys were found to be lower than those of the Fe-S alloys containing the same sulfur content. This was shown to be a mmzifestation of the increase in the thermodynamic activity of suZfur by carbon. It is only in recent years that attempts have been made to measure the surface tension of liquid iron of known high purity.1-3 Earlier measurements4-7 were made on liquid iron containing variable amounts of what are now known to be surface -active solutes. The exact value of the surface tension of liquid iron is still, however, open to some doubt. Halden and Kingery&apos; reported a value of 1720k 34 dynes per cm at 1570°C, Kozakevitch and Urbain8 gave 1790k 25 dynes per cm at 1550°C, while Van-Tszin-Tan et al. obtained a value of 1865k 37 dynes per cm at 1550°C. The first systematic investigation into the effect of controlled solute additions on the surface tension of iron was made by Halden and Kingery.&apos; They showed that sulfur and oxygen were highly surface-active, whereas nitrogen was only slightly active, and carbon inactive. A subsequent investigation by Kingery indicated that two other group-6B elements, selenium and tellurium, were also surface-active. This highly surface-active nature of sulfur and oxygen has recently been substantiated by Kozakevitch and Urbainla and Van-Tszin-Tan et al. l1 Kozakevitch and Urbainl2 have also conducted an experimental survey of the effects of a number of metals on the surface tension of liquid iron. Their surface-active nature was, in all cases, less than that of the group 6B elements. The present investigation was undertaken to study in more detail the surface tensions of dilute Fe-S alloys and to measure the surface tensions of binary alloys of iron containing phosphorus, copper, and tin. The effect of sulfur additions on the surface tension of Fe-1 pct C alloys was also determined. EXPERIMENTAL PROCEDURE The sessile-drop method was employed in the present investigation. An apparatus was built similar in principle to that described by Humenik and Kingery.lS It consisted of a horizontal silica tube, which could be evacuated to pressures less than 10-5 torr, with its central portion surrounded by a water jacket within which was a high-frequency coil. This generated heat in a tantalum susceptor placed inside the silica tube, which in turn radiated heat to the specimen mounted on a recrystallized alumina plaque. Temperatures were measured by an optical pyrometer and photographs of the molten drop were taken on a fixed-focus plate camera giving a magnification of X2. Surface-tension values were determined from the resultant drop using the method described by Baes and Kellogg.l4 The high vapor pressure of molten iron made it necessary to conduct all the experiments under a 1/4 atm of argon (greater than 99.995 pct purity). The analysis of the base iron used in the investigation is given in Table I. Each sample was approximately 3 g in weight and had a hemispherical base to ensure a uniform advancing contact angle on melting. The iron alloys were prepared individually in the sessile-drop apparatus by drilling a hole in the top of each sample and adding the required amount of solute, the drops being analyzed after the experiment. This method of preparation had the advantage of ensuring a consistent minimal contamination by oxygen due to refractory attack and also allowed surface tension to be measured at the same time. Every precaution was taken to ensure that the specimen was not contaminated by grease when it was introduced into the apparatus, the samples being cleaned in acid, dried in alcohol, and rinsed in petroleum ether. All handling was done with tweezers. Once the specimen had been placed inside the susceptor, the furnace was evacuated and the Sample leveled. The furnace was then degassed at approximately 1000"C before the argon was introduced. In every case the surface tension was determined at 1550" C.

Jan 1, 1963

By Joseph W. Roe, L. L. HEWES

A GRAPHIC solution of Kutter&apos;s formula for the flow of water has been worked out By Dr. L. I. Helves in connection with his course in Graphic Computations, given in the Sheffieild Scientific School, Yale University, which may be of interest to those who deal with canals, flumes and streams.

May 1, 1909

By Paul F. Kerr

QUARTZ of a certain kind, is one of our strategic minerals, and Brazil is probably the one important available source. Crystals of quartz of suitable size and perfection for piezoelectrical application are rare; their most outstanding use is in radio work. Clear quartz, or "crystal," free from twinning, cracks, foreign particles of other disturbing lines of growth, and gaseous or liquid inclusions, is cut into plates which provide excellent control of frequency in broadcasting. The squares or rectangles are less than a millimeter in thickness and ordinarily on the order of 1 in. along each side. They are cut at definite angles with respect to the axes of the crystal, and ground with opposite surfaces parallel. Each small slab must be a section of one crystal, uniform throughout in atomic alignment. The thickness of the chip controls the frequency of a broadcast and it is most important to have the plates oriented and ground with utmost precision. Opposite surfaces are parallel to within 0.001 mm. and expansion or contraction due to the temperature is limited to one part in a million.

Jan 1, 1942

By George A. Komadina

From its modest beginning in 1957 with one mill grinding section handling 3000 tpd Pima has steadily expanded. In July 1966, work was completed that allowed the concentrator to treat in excess of 18,000 tpd. Almost immediately Pima embarked on another expansion program that will increase plant capacity to 30,000 tpd during the summer of 1967. This repeated expansion has corresponded with the development of additional low-grade ore deposits and with the improved operating economics realized by handling larger masses of material. Early in the life of Pima it was known that a mineralized area was present on the flanks of the high-grade orebody which systematic drilling had shown to be a low-grade copper orebody. Many months of engineering studies revealed that this was sufficient to allow Pima to compete with other large scale, low-grade copper operations in the Southwest.

Jan 11, 1967

By AIME AIME

AMONG the European nations Germany is the center of interest economically as well as politically, and of prime importance for Europe as a whole is Germany&apos;s capacity to produce mineral products for armament and for export in exchange for the import of the essential supplies to maintain its industries. So far as minerals are concerned, Germany is worse off than any other great power except Italy, and deficiencies are being met by attempts to increase output from local deposits and by greater use of substitutes derived from domestic raw materials to replace imported metals, petroleum products, and other minerals.

Jan 1, 1939

By H. J. Fraser

LIKE a runner catching his second wind, the mining geologist in 1944 has had some opportunity to appraise the result of three years of active and intense search for the metallic sinews of war and peace. The war period has been one of physical activity and accumulation of new data but has not so far resulted in the announcement of any profound or revolutionary theoretical concepts or techniques. Most technical publications during the year have been either descriptive or statistical. A review of accomplishments during the war years, although affording some measure of satisfaction in individual cases or regarding production of certain metals or&apos; ores, is far from justifying any feeling of complacency regarding the growth of the profession either in fundamental knowledge or in application. During 1944 an abundant supply of all metals and minerals flowed steadily to smelters and fabricating plants. Also, during this and preceding years, adequate stock piles for war needs, in view of the improved foreign and domestic supply situation, were accumulated in many metals in such quantities that the mining industry has become concerned not with the problem of supply but with the effect these accumulated stocks, if maintained, might have on the postwar market. These considerations culminated in the enactment by Congress of the Surplus Disposal Act, which, admittedly a tempo-

Jan 1, 1945

THE TRANSACTIONS of the Institute for the early years display but Little interest in physical metallurgy-indeed, it is striking how thoroughly process metallurgy absorbed attention until quite recent years. The first volume carries no article that can be strictly described as physical metallurgy, unless one on the rolling and hammering of ingots be doubtfully so described. Nor does the second volume contribute more the interest then was in mining, and in production methods, both ferrous and nonferrous, with much attention to the new methods of making steel. The third volume records papers on: the condition of carbon in gray and white iron, a paper devoted to chemical rather than microscopic analysis; the annealing of spiegeleisen; phosphorus and carbon in iron and steel, similarly chemical. Much attention was given, and continued to be given for years, to the manufacture and behavior of rails. The question of the nature of steel appeared early (Vol. 11)-What is Steel, by A. L. Holley-where arguments on nomenclature were already active; and Holley also bemoans, in modern spirit, the Inadequate Union of Engineering Science and Art; Pearse wrote on cast iron for guns (reflecting again the ironic beneficence of war in metallurgy), and said that Captain Walbach was the first to insist on chemical analysis of gun irons; he quotes Major Wade&apos;s study of comparative hardness, using penetration hardness measurements (Brinell was to come later), and quotes the important Reports on the Strength and Other Properties of Metals for Cannon, by H. C. Baird, Philadelphia, 1855, in which the advanced state of tensile testing at the time is shown. Hewitt, in Vol V, comments upon the function played by technical schools and technical societies upon the growth of metal-

Jan 1, 1948

By Lester Uren

Beginning with theoretical concepts of oil drainage, this paper demonstrates that the flow of petroleum into a well from a stratum of oil-saturated sand of uniform texture increases with the diameter of the well. This conclusion is supported by experimental evidence. It appears that if a well may be reamed to a diameter of 20 ft. within the oil sand, its production will be approximately doubled. A novel method is proposed for forming and supporting a cavity of such proportions within the oil-producing stratum. PETROLEUM occurs, in nature, as a fluid saturating the pore spaces between the grains of porous rocks or aggregations of rock particles such as sand, sandstone, conglomerate, shale, limestone, etc. The oil, under the influence of gas pressure, hydrostatic pressure, gravity, earth pressure, and, perhaps, other natural forces, is caused to flow through the porous "reservoir rock" into wells penetrating the stratum in which the oil occurs. The principal moving force is the pressure of dissolved or occluded natural gas within the oil, though this;, force is assisted by gravity and by the hydrostatic or buoyant pressure of ground water about the edges of the "pool." The wells, providing outlets to the surface, are centers of reduced pressure and the flow of rock fluids into a particular well is usually an expression of the difference in pressure existing between the space within the well and that of the stored oil .within the reservoir rock. The greater this differential pressure, the more rapidly will oil flow from the source rock into the well. Opposing movement of the oil from the reservoir rock into the well are certain natural forces related to the rock structure, such as pore friction and capillarity, and certain others related to the physical properties of the oil, such as viscosity and adhesion. The differential pressure between the well and the boundaries of the area drained by it must be sufficient to overcome the forces opposing flow if there is to be movement of oil into the well. If by any device the resistance to movement of the oil may be reduced, the oil will flow into the well at a more rapid rate and the effective area of drainage will be increased.

Jan 10, 1924

By Thomas Henderson

Strategically, intermaterials competition is important to companies involved in raw materials extraction, smelting, refining or other processing, semi-finished and finished goods fabrication, and end-use consumers. In other words, just about every company involved in manufacturing. The array of materials covered by other papers in this session is testimony to the subject&apos;s breadth. In trying to provide an over- view of such a broad topic, the purpose has been to relate some of the common characteristics of the markets, economics and technology of raw materials, and to describe some of the ways in which Intermaterials competition impacts the markets, economics and technology of raw materials.

Jan 1, 1982

By Will H. Coghill, Fred D. DeVaney, R. G. O’Meara

The size of ball mills in the ore-dressing industry has increased from about 4 ft. in each dimension to 10.5 ft. in diameter by 8 ft. in length. In the cement industry they are as long as 45 ft. Plainly the trend has been toward larger mills. The common belief is that the big mills economize in floor space and first cost, but the advantage with respect to friction has not been clearly defined. In the ball-mill studies at Rolla, Mo., laboratory mills as small as 2 by 2 ft. have been found as efficient in terms of the amount of grinding per unit of net power as mills 6 by 4 or 6 by 12 ft. Therefore, if supremacy can be claimed for the big mills, advantage must come from other sources. The advantage to be considered here is reduced loss by friction or dead load. In the study to determine whether big mills have relatively less loss by friction the commercial catalogs were used for fundamental figures. The dimensions and weights of Table 1 are taken from the catalogs (the last line gives data on a Rolla laboratory mill). The net power—that is, the power expended within the mill for grinding—is calculated by a new formula.&apos; The assumed speeds are each at 70 per cent of their theoretical critical speeds, and the mills are loaded to the center with balls. In other words, they are assumed to be working under analogous conditions and are set for good grinding. In the last column the ratio B: A shows that the larger commercial mills are lighter per unit of net power than the smaller mills, and more of the motor output should therefore go into grinding. The laboratory mill seems to have some advantage over the larger mills; it would be expected to be light because it has no liners.

Jan 1, 1935