Search Documents

By D. J. Spottiswood, C. N. Robinson, D. E. Spiller, E. G. Kelly

This paper describes the performance of a new design of spiral that is optimized for fine coal cleaning. Reduced Performance (Tromp) curves are presented to compare this spiral with the older design, as well as with other commonly used coal cleaning equipment. As an aid to equipment selection and circuit design, data are also presented to show how variables, such as flow rate, pulp density, and particle size, affect efficiency and the separation specific gravity.

Jan 1, 1985

By K. S. Lane

The problem of stability of slopes in reservoirs is one of real interest in civil engineering. The problem is whether the valley walls will remain stable or whether they are likely to slide as conditions are changed by storage of water in the reservoir. If major slides are indicated, as on the walls of relatively steep canyons, one must estimate whether they will be so located and of sufficient size as to interfere with operation of the reservoir-as by blocking the outlets, or by displacing sufficient water to over-top the dam in a huge wave. Some cases involve problems in soil mechanics for slides in earth or weaker rock; other locations need the assistance of rock mechanics for slides in harder rock. While this is not a new problem, attention has recently been focused on its importance by the hugh landslide into the Vaiont reservoir in 1963, which claimed the lives of over 2000 people and forced abandonment of the dam and powerhouse. VAIONT RESERVOIR SLIDE Fig. 1 shows Vaiont Dam in Italy which is a double curvature arch, 875 ft high, located on a tributary of the Piave River, north and west of Venice. When completed in 1960 it was the highest arch dam in the world. In 1960 a sizable landslide (some 700,000 cu yd) occurred on the left abutment a short distance above the dam. Following this, the reservoir was held down for construction of a by-pass tunnel through the right valley wall to insure connection with the upper end of the reservoir in event of further slides. In October 1963 a giant landslide occurred on the left valley wall, over a width of some 14 miles (see Fig. 2). Over 300 million cu yd slid into the reservoir, displacing the water and forming a hige wave 700 ft above the top of the dam as it hit the opposite, or right, wall of the valley. The wave then passed some 500 ft over top of the dam, followed down the tortuous winding canyon and debouched into the

Jan 1, 1967

By Edward T. Koch

A new concept involving the use of a crawler-mounted slurrifier for open-pit ore mining and overburden removal is dealt with. The design and application are discussed. Based on field experience, the area and type of operation where this machine would be effective is indicated. The slurrifier is also compared with draglines, shovels, and bucket wheel excavators. A number of the design concepts, as well as the mechanical and operational parameters, are discussed.

Jan 1, 1976

By Luis Toron, Salvador Cortes-Obregon

John D. Price (Colorado Fuel and Iron Corp., Pueblo, Colo)—The paper on the coal fields of the Oaxaca district as prepared by engineers Toron and Cortes-Obregon of the staff of the Bank of Mexico bears witness to the thorough and careful way in which the men associated with this organization perform their work. There is little to be added to their paper in way of discussion other than to confirm and amplify some of their statements. Since the only extensive and well-developed field of coking coal lies in the northeastern section of the country adjacent to Sabinas in the state of Coahuila, it follows that blast furnace plants would be located in that same region. Two such plants are now operating at Monterrey and Monclova, using coke produced at the Sabinas district mines. But the nearer of these two plants is 600 miles from Mexico City and even farther from the center of population. Transportation of products from these mills to the market area is therefore expensive, both because of the distance and the difficulty of the terrain over which it must be carried. The development of an integrated steel industry closer to the center of population has therefore long been a goal toward which the Mexican technicians have been striving. While the presence of coal of some grade has been reported in many of the states, and many ideas have been advanced regarding its possible uses in iron and steel production, deposits of anthracite in Sonora and the various coals of the Oaxaca district as reported on in this paper are the only ones that have been explored in a serious manner. The coking coal from the Mix-tepec zone appears to offer promise of producing a coke which could be used in a standard blast furnace. Several problems are indicated, however: 1—The ash in the coal is high as mined, but indications are that it can be washed to an ash content of 15 pct with a recovery of 70 pct of washed coal. 2—Such washing would increase the volatile content from 17.4 pct to about 20 pct, and in a byproduct oven this should give a coke yield of close to 80 pct with an ash content of coke under 20 pct. 3—A free swelling index of 5 appears low for a good coking coal, and below that of the coals from the Sabinas district, which show between 6 and 9. But washing of the coal should result in an improvement in this regard; in the United States coals from Utah with an index even lower than 5 have made a usable coke. 4—A coal with volatile as low as 17.4 in raw coal and 20 in washed coal would come close to being classed as a low-volatile rather than medium-volatile coal, and low-volatile coals are notorious for their high expansion properties. Several plants in the United States are making coke from straight medium-volatile coal of 26 to 28 volatile content, and one at Rosita,, Mexico, from coal of 25 volatile. But no plants to my knowledge are using coal as low as 20 volatile. Since the Rosita coal appears to be a borderline coal from the angle of its expansion properties the coking of one of the straight lower volatile must be approached with caution. 5—There are few coals possessing any degree of coking properties which cannot be used in coke production by careful attention to its preparation and blending. The fact that coals of other types are available in this same region make improvement through blending very possible. 6—There are other workable methods of reducing iron ore other than the conventional coke-blast-furnace method. These will not be discussed here but it is known that their use has been considered. The technicians of not only Mexico but also of the other Latin American countries are keenly aware of their natural resources and their national needs. This paper emphasizes the fact that the Mexican technicians are working on their problem and attempting to speed the day of self-sufficiency for their country. Salvatore Cortes-Obregon (author's reply)—I wish to thank Mr. Price for his kind remarks. The Mixtepec coal as shown in Table II has 30 pct ash and a free swelling index of 5, but when the same coal is washed to 15 pct ash it has a free swelling index of 8 to 9 and the volatiles increased from 17.4 to 20.7 pct. A satisfactory coke has been produced from blends made in the Mexican laboratory using at least 40 pct of the Mixtepec coking coals with the other Oaxaca non-coking coals. Koppers in Germany report good coke obtained from the Oaxaca coal with a blend of 80 pct Mixtepec coal. Consideration is being given the possibility of using methods other than the conventional blast furnace for the reduction of iron ore near the Oaxaca area; electric furnaces appear promising. The non-coking coals could be used to produce cheap electric energy and the coking coals to make metallurgical coke.

Jan 1, 1955

By C. J. Guntner, R. P. Reed

A commercial 18Cr-8Ni iron alloy (AISI 304L) was examined in tension at 300°, 76°, 20°, and 4°K. Continuous stress-strain recordings were made, X-ray analyses at periodic stress (strain) intervals were obtained, and the magnetic measurements were taken. From this data the percentage of martensitic products [bcc(a) and hcp (E)] was computed as a function of stress (strain). It was found thatup to 15 pct E phase forms at low temperntures. The amount of E formed increases to a maximum at about 5 pct strain, then decreases. This decrease indicates the additional transformation of E to a'. The total amount of E and a' was suppressed at constant stress (strain) at 4°K as compared to 76°K. It is proposed that the suppression of E and a' is associated with the decreased mobility of extended dislocations at very low temperatures. The yield strength decreased as the temperature was depressed below room temperature and then increased rapidly near 4°K. SOME ferrous alloys which are austenitic (fcc ?) at room temperature appear to be unique in that two martensitic products (hcp e and bcc a') may form on cooling to lower temperatures or on application of mechanical stress. The most common room-temperature austenitic ferrous alloys are 18Cr, 8Ni stainless steels. Most aspects of the spontaneous transformations have been previously described for these steels.' Several previous papers have described special aspects of the stress-induced transformations at low temperatures for the stainless steels, such as the existence of the hcp phase (c) after straining at 76oK,2-7 the morphology after straining using electron microscopy,7 and the decrease in E at higher strains at 76oK.4 However, for a complete representation, one must know the stress-strain characteristics and the dependence of both martensitic products on applied stress and temperature. It is the intention of this paper to provide that documentation. To accomplish this, continuous stress vs strain recordings were made at four temperatures: 300°, 76", 20°, and 4°K for annealed AISI 304L (a commercial 18Cr-8Ni alloy). At periodic stress intervals at each temperature the integrated X-ray line intensity of a selected peak for each phase (y, E, and a') was measured. In addition, photomicrographs of the strained surfaces were taken and magnetic measurements were made. The magnetic readings can be directly converted into percent a'.',e With these measurements the percentage of each phase may be plotted as a function of stress (or strain) and test temperature. It was found that up to 15 pct E phase forms upon stressing the AISI 304L alloy at low temperatures. The E percentage increases abruptly after the alloy yields, but then decreases gradually at higher stresses. The rapid increase in e at 76°K is associated with an "easy-glide" portion of the stress-strain curve. The total amount of a' + .G is suppressed below 76°K at a constant stress or strain. The yield strength decreases down to 76°K but increases rapidly below 20°K. EXPERIMENTAL PROCEDURE Tensile test specimens were cut parallel to the rolling direction from 0.1-in.-thick sheet. Continuous stress vs strain recordings were obtained at each test temperature (300°, 76o, 20°, and 4°K) using equipment and methods described elsewhere.' The specimens which were used in the X-ray analysis were stressed to successive increments of strain at each temperature, analyzed at room temperature, then restressed at the test temperature. This procedure was repeated until approximately ten X-ray analyses had been performed with approximately 1.0 pct strain increments. The specimens had a reduced section 1 in. long, 1.2 in. wide, and 0.1 in. thick. They were electro polished prior to testing and after each strain increment. Table I lists the chemical composition, grain size, and hardness for the alloy which was used. This is the same alloy for which extensive mechanical-property tests3 and morphological studies of the spontaneous transformations' have previously been made. For the low-temperature tests (76o and 4°K) below the Ms temperature the specimens were initially cooled to the test temperature, held for 1/2 hr, then warmed and X-rayed at room temperature. The results are listed in Table 11. From earlier work8 it was known that additional transformation on the second cycle would be considerably less (-0.1 pct

Jan 1, 1964

By M. H. Loveman

The orebody described below has been rediscovered and developed within the last 3 years. It has, however, been known and worked by the Chinese for hundreds of years. When assay values and size are considered, it contains what is probably one of the largest single bodies of zinc and lead sulphides yet found. The tonnages developed at other places, as at Broken Hill, are much greater but the average zinc and lead sulphide contents are considerably lower than at Bawdwin. Bawdwin is situated in the semi-independent State of Tawng Peng, one of the numerous units which make up the Northern Shan States. These States are under British rule and are generally considered as a portion of Burma. They are governed as a separate administrative unit, however, under the Lieutenant Governor of Burma. Each State is under its own chief, or Sawbwa, who has considerable power over his own subjects. Bawdwin is approximately in latitude N 23°6', longitude E 97°201, about 50 miles south of the nearest point on the Chinese border and 450 miles north of Rangoon (Fig. 1). The period at which mining was first begun at Bawdwin is unknown. The most reliable records have been obtained by deciphering local Chinese inscriptions and from these it is concluded that the work dates back to at least the beginning of the 15th century. The first undoubted reference to the mines by a European is by Syrnes in 1795. Crawford in 1827 estimated the output of silver from the mines at $600,000 anually. At about the middle of the 19th century the rebellion of the Chinese Mohammedans in the neighboring Chinese province of Yunnan so weakened the power of the Chinese that the incursions of hostile tribes (Kachins) made work extremely dangerous. The mines were finally abandoned by the Chinese about 1868. The . closing down of the mines was probably not entirely due to outside causes but may have been influenced somewhat by the increasing difficulty of handling the water, as the workings gradually descended below the water level of the district. Several attempts were made by the Burmese kings, Mindon Min and Thebaw, to resume operations, but because of a

Jan 1, 1917

Minnesota School of Mines Experiment Station, University of Minnesota, Minneapolis, Minn For copies of Bulletins or a list of publications, address The Director Bulletins available are Bulletin 1, Iron mining in Minnesota, by C. E Van Barneveld (1912), $1, 2, Concentration tests on Mesabi ores, by W R Appleby and E Newton (1913), 3, Preliminary concentration tests on Cuyuna ores, by W. R Appleby and E Newton (1915), 4, Bibliography of Minnesota mining and geology, by W. Gregory (1915); 5, Manganiferous iron ores of the Cuyuna district, by E Newton (1918), 7, The future of the Lake Superior district as iron-ore producer, by E W. Davis (1920), 9, Magnetic concentra¬tion of iron ore, by E. W Davis (1921); 10, Ball mill crushing iii closed circuit with screens, by E W Davis (1925); 12, Minnesota manganiferous iron ore in relation to the iron and steel industry, by T L Joseph and S P Kinney (1927). A mining directory of Minnesota, by J J Craig, is published annually.

Jan 1, 1933

By H. F. JR. Miller

(Butte Meeting, August, 1913.) THE major cause of the deterioration of the open-hearth furnace as its length of service increases, is the melting down, or rather the slagging, of the checker-brick, together with the deposition of dirt in the form of iron oxide, etc., which helps to close the openings, as well as to slag the brick by chemical action. Any construction that will do away with the necessity of having the waste gases come down through the checkers will eliminate the main reason for their deterioration. There are some other well-defined reasons which are subordinate to the main one given above. Some of the defects of the present type of regenerator chambers are as follows: 1. The checkers cannot be cleaned while the furnace is in operation, nor can they be cleaned at the end of the run without taking out all of the checker-brick. This causes high costs for labor and brick. The labor cost is high because all checker-brick have to be handled twice. The brick cost is high because many of the bricks are spalled in the double handling, rendering them useless because a spalled brick will not stand up. 2. The top courses of brick become coated with iron oxide, etc., melt clown, and large amounts of dirt are deposited throughout the checkers, especially at the bottom. The draft of the furnace is decreased by the closing of the top and bottom openings, especially the top ones, and the entire working of the furnace is affected. If an effort is made to clean the checkers the dirt and brick falling down into the holes still further diminish the draft. 3. The distribution of the air or waste gases through the checkers is in many cases uneven, resulting in a lower temperature of pre-heated air and therefore a slower working furnace. Also, the passage of air and waste gases is so crooked that sometimes the chimney is not powerful enough to overcome the friction.

Jan 6, 1913

By James K. Richardson

FIRST indications that mineral industries expansion is beginning to show results are contained in the report by Defense Mobilizer Charles E. Wilson, The Battle for Production. The report, submitted to the President early this year, says that the United States has reached a $2 billion-per-month rate in military deliveries-three times that of 1950. Plant expansion in 1951 totalled $11.1 billion, the report states. Certificates of accelerated amortization have been approved to cover $11.4 billion in proposed plant construction. In reference to plant expansion significant to the mineral industry, the report states: •Steel industry goal is 120 million ingot tons by 1954, compared with present 108 -million ingot ton capacity. •Taconite beneficiation should result in 15 million tons by 1955. •An existing annual aluminum output rate of 860,000 tons. •An estimated 500,000 tons of sulphur by late 1953 •Manganese production up 50,000 tons as- the result of new projects in 1952. •Montana tungsten project coming into production in 1952. •Present zinc production expansion projects to add an estimated 150,000 tons to the 1951 production figure in 1953. Information gathered from official sources, other than Mr. Wilson's report, indicates an increase in the annual capacity of other segments of the industry by 1955, as shown in Table I. [ ]

Jan 1, 1952

By A. M. Tweedy, Felix A. Vogel

Since the publication of Prof. J. W. Richards's paper on The Schumacher Briquetting Process,' this process has been in operation on a practical scale in two plants in the United States, and a few notes on the results obtained may be of interest. An experimental plant, consisting of a toggle press and a hydraulic press, was installed at Johnstown, Pa., together with the necessary bins and other equipment, and an attempt was made to briquette a mixture of Mahoning fines and blast-furnace flue dust, in a ratio of 7 parts of ore to 3 parts of dust. The results were unsatisfactory, in that the briquettes made were not hard enough to stand the severe handling to which they were subjected in the various transferences necessary between the press and the furnace. The trouble was due to several causes: First, the mechanical arrangement of the plant, which did not lend itself to a proper hardening and loading of the briquettes into the cars. Second, the irrrgular composition of the flue dust, as to both its lime and its fine coke contents. Third, the variability of the moisture content of the ore, and its viscosity when wet. Fourth, the ratio of fine ore to flue dust; that is, it was attempted to bind in too large a quantity of fine ore for the small amount of flue dust used. The first trouble could be overcome, and has been improved upon in the plant as it stands to-day. The second trouble was important, because of the small amount of dust used as a binder, and might have been easily removed by mixing the flue dust of the different furnaces, which, however, was never done. The third difficulty was more serious, but could have been partly solved, had it been possible to meet this along with the fourth difficulty, by decreasing the percentage of ore in the briquettes. It was proposed to do this, but it seems that the problem at the works in question is, primarily, to prepare Mahoning fines for reduction in the blast furnace, and only secondarily to use up the flue dust, and a solution along this line did not seem to be interesting.

Jan 1, 1914

By Francis Crockard

DURING the past five years we have probably witnessed greater technological advances than in any similar period. Industry and science have steadily marched ahead. The makers of iron and steel products have watched with great interest the development of stream-lined trains, faster and safer airplanes, the entirely new science of air-conditioning and the widespread use of stainless steels. Since 1930, we have witnessed the erection of the world's largest suspension bridge, the largest and fastest ocean liner and the spectacular Boulder Dam, while even greater things are planned in these particular fields. Other indus-tries, too, have been moving ahead rapidly. This advance in a few years has been caused primarily by the fierce competition of the depression. Now, more than ever, is the emphasis placed upon quality and service. Makers of southern merchant pig iron have been no exception and have been confronted with increasingly strict chemical specifications and with much greater stress on physical characteristics than ever before. For example, sulfur in the iron must be held very low, competition demanding that it be in the 0.020's and low 0.030's; silicon content must be held within a very narrow range, and definite requirements of phos-phorus and manganese are an essential part of the specifications. Physical characteristics are becoming of increasingly greater impor-tance. The introduction of triple-skimmed, slow-cooled iron several years ago was the first step in this direction. Now there are a few customers who buy iron by chemical analysis and physical appear-ance, having found that the analysis alone is an insufficient guide to their requirements.

Jan 1, 1936

By J. E. Dorn, L. A. Shepard

LOW and Gensamer' demonstrated a number of years ago that the yield point phenomenon in mild steels was associated with the presence of fer-rite soluble carbon or nitrogen. More recently the yield phenomenon in body-centered-cubic metals containing interstitials was rationalized by Cottrell' in terms of a simple dislocation model. Interstitial atoms interact with dislocations in two ways; they cause not only local expansions but induce local tetragonality in the lattice. Consequently, interstitial~ interact with the hydrostatic tension and shear components of the stress about dislocations. They tend to migrate toward the expanded regions of edge dislocations and to assume sites that relieve the shear stresses of screw dislocations. Thus, a dislocation saturated with solute atoms constitutes a lower free energy state than that obtained when the dislocation threads through the average composition regions of the matrix. A greater stress will be required to separate the dislocation from its atmosphere than to move the dislocation through the matrix. This factor gives rise to the upper yield stress, which is required to unleash a series of dislocations in a localized region. This local yielding is propagated across the specimen to form a thin band of plastically deformed material known as a Lueder's band, making an angle of about 45" to the stress axis. Once the band has formed, deformation continues at the lower yield stress by the spreading of the Lueder's band in the direction of the applied stress. Undoubtedly the spreading of Lueder's bands at the lower yield stress is accomplished by the high stress concentrations at the band fronts, which serve to induce continued unlocking of new dislocations in advance of the migrating band fronts. Cottrell and Bilby have shown that the dependence of the yield point on temperature can be deduced by assuming that thermal fluctuations aid the stress in unlocking small dislocation loops from their solute atmospheres. Once a loop that exceeds a critical size has been nucleated, the entire locked diqlocation is released and can migrate. Fisher4 simplified this analysis by assuming that the locking forces were short range, so that if the dislocation loop were displaced only one Burgers vector from its atmosphere, it would be unlocked. Applying his model to the special case of delayed yielding under a constant stress of the order of the upper yield strength, he demonstrated that the delay time 7 for yielding should depend on stress and temperature according to where A and B are constants, G is the shear modulus, and u and T are the resolved shear stress and absolute temperature, respectively. Cottrell and Bilby, Fisher, and Fisher and Rogers' have shown that the above deductions are at least in qualitative harmony with the experimental facts. A number of investigators5-0 have shown that the yield point phenomenon can also be induced in sub-stitutional alloys of face-centered-cubic metals. In general such yield points are not as pronounced as those encountered in body-centered-cubic metals containing interstitials. The yield point phenomenon in these materials is usually enhanced by prestrain-ing at low temperatures and aging at intermediate temperatures. Undoubtedly the yield point phenomenon induced by strain aging substitutional alloys also results from locking of dislocations. But the locking of dislocations in substitutional alloys of face-centered-cubic metals differs somewhat from interstitial locking of dislocations in body-centered-cubic metals. Substitutional elements in face-centered-cubic lattices cause only radial displacements of the adjacent lattice points. Consequently, only the edge components of dislocations can be locked by the mechanism suggested by Cottrell. Additional locking, however, can be obtained by the Suzuki mcchanism.10 In face-centered-cubic metals, dislocations exhibit lower energies when they are present in the

Jan 1, 1957

By V. V. J. Sarma

Interpretation of earth resistivity data involves not only obtaining depth to interfaces but also determining the nature of formations from their resistivity characteristics. Moore's method of interpretation envisages obtaining depths to the interfaces alone. A simple method of estimating the true resistivity values of formations by applying Hummel's formula of average resistivities is proposed. The method would increase the interpretative value of Moore's method as originally proposed. For most of the earth resistivity measurements, the four-electrode configuration developed by Wennerl is employed. In principal, the method consists of energizing (Current I) the ground through two outer electrodes and measuring the resultant potential (v) between the two inner electrodes. The configuration is such that the separation (a) between any two successive electrodes is equal. The apparent resistivity (pa) for such a configuration is given by 2p- a (V/I). By increasing the electrode separation (pa vs a) curves are obtained. Ideally, a homogeneous isotropic formation underground has a characteristic resistivity. However, the field conditions do not present such ideal cases. Almost invariably, even in the same geological bed, the physical conditions are widely different at different parts in the bed. It is further shown that the penetration of the current into the ground for a given horizontal electrode separation, a, is roughly down to a depth, equal to a. It is therefore, evident that the apparent resistivity calculated from the field observations is a weighted average of the resistivities of the materials present down to this depth. With some prior knowledge about the relative dispositions of the geological formations and their physical conditions, it would be possible, by resistivity surveys, to obtain characteristic resistivities for these formations. It is, thus, that the apparent resistivity-electrode separation curves enable one to decipher the resis- tivity distribution at various depth levels and therefore the nature of the geological formations present. Both empirical and theoretical methods have been developed for determining resistivity characteristics of the various formations. The theoretical methods proposed by Tagg2 and Roman3 are derived from studies of the potential distribution on the surface due to the presence of layers of widely differing resistivities underground. The more recent methods of Wetzel and McMurry4 and Wetzel and Mooney5 are but extensions of the original Roman method of superposition. These methods suffer from lack of similarity of the actual field conditions with those of assumed conditions in developing the theory. The empirical methods such as the one developed by Gish and rooneY6 depend purely on personal observation and local peculiarities, and are applicable only for those limited areas. Out of the empirical methods, moore's7 cumulative resistivity method is still found to be applicable in several localities of differing conditions. While Reudy in 1945 adduced some theoretical justification for the method (Eve and Keys),8 Muskat9 and Mooney 10 tried to show the lack of theoretical basis for the same. It is, however, observed that the method in practice "forms a valuable means of successfully attacking the apparent resistivity curves which fail to respond to the Gish-Rooney, the Tagg or the Roman logarithmic methods" (Ramachandra Rao). 11 Comparatively good results are also reported by Melbyel2 by employing Moore's method in interpreting the resistivity results obtained for ground water in the city of Gunnison, Colo. MOORE'S METHOD As has already been pointed out, the application of the theoretical methods is time-consuming, laborious and sometimes not applicable for quick and accurate interpretation of the field data. moore7 has developed a quick method for obtaining depths to interfaces by plotting the cumulative sums of resistivities, against the corresponding electrode separations a instead of plotting the usual Pa — a curve. In this process of continuous integration, corrections for small variations in resistivities, arising due to local surface conditions or adjacent layers, are made, while large consistent variations are brought out

Jan 1, 1963

By Roswell H. Johnson

What becomes of the water which must have filled the oil and gas sands at the time of deposition, has long puzzled students of oil and gas and has found expression in Munn's well-known article on the hydraulic theory. Both Munn and Clapp have pointed out that in the Appalachian field the deeper sands carry increasingly less proportionate amounts of water. It seems to me probable that the principal source of oil and gas has been in the shales in proximity to the sands which now contain these products. The sand spits which mark off the lagoons from the sea comply particularly with the requirements of a limited sand imbedded in shales rich in organic matter. Cunningham Craig has objected to this view that the rich organic muds of lagoons are found only at the surface. That such muds do extend to considerable depth 1 am assured by Prof. Douglas W. Johnson, who has made an extensive study of the Atlantic Coast marshes. As any particular sand body becomes weighted by a heavier and heavier overburden, the result of increasing deposition, a part of the very large percentage of water in the uncompacted sand and mud is forced out. The water percentage of freshly settled mud is vastly higher than that of the resultant shales, or even of a very porous sand. If beds of less compressible material meet or underlie the shales in question, there will frequently be a lateral motion along such beds to some point where the upward movement will be resumed. We find in our laboratory work here that oil, gas, and water have extremely slight capacity for gravitational sorting while in a state of rest, but when moving the gravitational sorting is readily accomplished. As the oil, gas, and water pass a body of larger pores, the gas, owing to its lack of capillary attraction, is retained in the large pores. This has been predicted by Washburne, Blatehley and others on the ground that the water has a higher capillarity and grips the finer pores in such a way that there will be a greater proportion of oil and gas in the large

Jan 1, 1915

Papers in Classes A-Metal Mining, B-Milling and Concentration, H-Industrial Minerals, and I-Mining Geology are distributed in MINING TECHNOLOGY, which is issued every Other month. Papers in Classes C-Iron and Steel Division, D-Nonferrous Metallurgy and E-Institute Of Metals Division are distributed in METALS TECHNOLOGY, which is issued twice quarterly. Papers in Class G-Petroleum Division are distributed in PETROLEUM TECHNOLOGY, which is issued every Other month. TECHNICAL PUBLICATIONS in Classes F-Coal Division, J-Mineral Industry Education Division, K-Mining Administration, and L-Geophysics, are issued as separate pamphlets. Contributions are papers that when printed Or mimeographed are available, but Only On request. All the TECHNICAL PUBLICATIONS Of the F, J, K Or L classes, the TECHNOLOGYS and the CONTRIBUTIONS issued in 1945 are available at Institute headquarters, unless Otherwise noted. They are also On file in many public, university and technical libraries and, when so indicated in the list, the papers may be found in the TRANSACTIONS. An Institute member is entitled to One copy Of any TECHNOLOGY, TECHNICAL PUBLICATION Of the F, J, K Or L classes, Or printed Or mimeographed CONTRIBUTION. Copies Of TECHNOLOGYS and TECHNICAL PUBLICATIONS Of the F, J, K Or L classes listed have been mailed to members Of the Institute according to their registration by classes. CONTRIBUTIONS will he sent upon request. A member may purchase an additional copy Of a TECHNICAL PUBLICATION Of the F, J, K Or L classes, a paper in a TECHNOLOGY, Or a CONTRIBUTION at One cent a page; minimum charge, 25¢.

Jan 1, 1946

THE following statement is contained in an article entitled "Mortgaging the Future." by Walter C. Teagle, president of the Standard Oil Co. of New Jer-sey, appearing in the current issue of the Lamp, the official organ of the Standard Oil Co.: "During the last eight months the domestic daily production. of crude oil has risen 300,000 bbl.. which means that no less a volume than 2,500,000 bbl. now are coming to market each day. . . . Every twenty-four hours 250,000 bbl. more than the consumer required are being added to our surplus oil storage. The temporary advantage of cheap petroleum products and the availability of fuel .oil, for a widespread use as a substitute for coal are not being weighed against the time when scarcity may follow on the heels of plenty and the public of tomor-row may have to pay for today's excesses. The over-production of crude and its consequences constitute a problem of national import which far outweighs the temporary advantages either to a part of the industry or to sections of the public.

Jan 8, 1927

By G. R. Speich

The precipitation of the Feab and Fe,Ti Laves phases (MgZn, type, C14) from Fe-Nb and Fe-Ti solid solutions, respectively, has been studied in the temperature range 500" to 800°C using hardness measurements, light and electron microscopy, and X-ray and electron diffraction. The Fe-Nb alloys contained 0.96, 1.67, and 3.80 pct Nb and the Fe-Ti alloys 3.5, 5.8, and 8.8 pct Ti. In both systems only the equilibrium Laves phase is formed, with nucleation occurring at grain boundaries, at dislocations, and in the matrix. No cellular precipitation or transition phases were observed. The precipitation of the Laves phase in a fine dispersion leads to significant hardening in both systems. The hardness of the aged alloys is proportional to the reciprocal of the square root of the interparticle spacing. The maximum solid solubility of titanium in a! iron is 9.0 pct Ti at 1280°C. THE precipitation of the FezNb and FezTi Laves phases (MgZn2 type, C 14) from Fe-Nb and Fe-Ti solid solutions, respectively, has been investigated as part of a continuing study of the mechanisms of precipitation from ferritic binary iron-base alloys. The iron-rich portions of the Fe-Nb and Fe-Ti phase diagrams are shown in Fig. l(a) and l(b). The Fe-Nb diagram is essentially that given by ansen' with the more recent work of Hume-Rothery and Gibson2 added. Goldschmidt3 indicates that the FezNb Laves phase has a solubility extending from 32 to 55 wt pct Nb. The Fe-Ti diagram is also essentially that reported by Hansen.l The recent results of Nishimura and kamei, Murakami, Kimura, and Nishimura,' indicate that the FezTi Laves phase has a solubility extending from 22.5 to 30.5 wt pct Ti. The L/6 + FezTi eutectic temperature of 1298°C indicated by Kornilov and oriskina' has been adopted. The addition of niobium or titanium to iron lowers the 6 — y transformation temperature and raises the y — a! transformation temperature. This results in a closed y field in the Fe-Ti system, but the lower solubility of niobium in a! (6) iron results in a eutec-toid, 6 — y + FezNb, at 1200°C, and a peritectoid, y + FezNb —-a, at 989°C in the Fe-Nb system. The maximum solubility of niobium is reported to be 4.5 wt pct in 6 iron,' 1.0 wt pct in y iron,7 and 1.8 wt pct in a iron.' Some results from the present work indicate that the maximum solubility in a! iron is actually less than 0.96 wt pct Nb. The maximum solubility of titanium in a! (6) iron is somewhat uncertain since the early work of To faute and Butting-haus indicated a value of 6.0 wt pct while later work of Kornilov and Boriskina6 yielded a value of 14.0 wt pct. The present work indicates that the maximum solubility is actually 9.0 wt pct. In both systems the phase in equilibrium with the iron-base solid solutions is a Laves phase (Mg znztype, C14), FezNb or FezTi. Both of these Laves phases have a wide range of Solubility. The precipitation-hardening behavior of Fe-Nb or Fe-Ti alloys has not been studied extensively. Genders and Harrison' reported that binary Fe-Nb alloys hardened upon aging. Peter and Fisher7 studied the mechanical properties of Fe-Nb and Fe-Ti alloys quenched from different phase fields.

Jan 1, 1962

By A. L. Mular

Two equations express the integral rate at which fines are produced from a homogeneous material: It has been demonstrated that the Gaudin-Meloy distribution for single fracture is equally applicable to multiple fracture and is related to the Gaudin-Schuhmann distribution at least when the distribution modulus a is close to unity. A, xoY was found to be independent of starting mass over the range studied when particle size was held constant. The equations are related to the input energy to the mill. In an earlier paper,' it was shown that when Mo g of uniformly sized homogeneous material is ground dry in a batch rod mill, the energy-size reduction equation is expressed at any time by the mass of unbroken starting material left at time t, ku is the size modulus of the portion Mo - Mt, and P is a constant that is generally equal to the distribution modulus a. If the power to the mill is constant, Et is proportional to time and Eq. 1 is rewritten where (Mo -Mt)/t is actually the integral rate at which fines are produced from a parent material, and A, is another constant. The size modulus, k,, is determined from the Gaudin-Schuhmann equation:2 where y is the cumulative fraction finer than any size x. Recently, Gaudin and Meloy derived a distribution equation for single fracture on the assumption that the random fracture of a homogeneous material produces daughter particles of similar shape. Their equation is given by where y is the cumulative fraction finer than size X, x, is the size of the unfractured parent, and r is designated the size ratio. Although Eq. 4 is derived for a single event, it should also approximately hold for a series of com-

Jan 1, 1962

By Fred C., Fred C. Bond

Comminution energy is principally energy of deformation before breakage, which appears as heat. An empirical equation is presented which covers the entire comminution range. The new strain-energy theory considers comminution from the known principles of mechanics and the reduction ratio. Energy requirements according to the different theories are compared.

Jan 1, 1950

By W. A. STERLING

IN the opencut iron mines of the Mesabi Range in Minnesota, the trend in mining is in the development of mining equipment and mining methods which will move surface overburden and ore-bearing materials with less labor and at a cheaper cost. This is a must for most of the independent operators. Their reserves of direct-shipping ore are extremely small and their operations are being conducted in small, or intermediate pits, with a high stripping ratio in the outer fringes, or shore lines of older pits. and in ore bodies passing from direct shipping to the washing and the intermediate, or retreat ore state. The trend is toward deeper stripping, longer and steeper hauls, and the necessity of moving a total of from three to five or six tons of overburden and ore material for each ton of shipping-grade ore produced. This naturally calls for greater production, with larger shovels, or draglines. cheaper drilling and blasting costs through the drilling of larger-diameter blastholes, and cheaper haulage through the use of trucks of larger capacity and more extensive use of belt-conveyor systems. This trend is notable both in stripping and mining.

Jan 1, 1948