Search Documents

By C. D. Hall

This paper may be divided into two main parts: (1) analysis and data to show that Eq. 6 adequately correlates the authors' experimental data, and (2) the assertion that Eq. 20 "should permit scale-up with data taken from one pipe diameter for Newtonian, inelastic non-Newtonian, and viscoelastic fluids, such as dilute polymer fracturing fluids, which produce considerable pressure reductions." The authors might well recommend that this broad grouping of fluid types could be correlated by using Eq. 6 (requiring data from at least two pipe diameters). On the other hand, Eq. 20 is only shown to be adequate for conditions within the range of the present data set. Specifically, predictions by Eq. 20 for diameter scale-up to casing sizes would give larger deviations than implied in Table 2, and scale-up for some other fluids that give large drag reduction could be grossly in error. The description of a class of fluids "which produce a diameter family of straight parallel lines on a log (d?p/4L) vs log (8 v/d) plot. . ." defines a necessary condition for using Eq. 6; i.e., that s shall be constant for each fluid. The proposal that Eq. 20 is applicable to turbulent flow of such fluids is equivalent to saying that the spacing of these parallel lines, with A being constant, will be found to correspond to m = -1.20 for all such fluids. Table 1 shows the values of m derived from data on 16 non-Newtonian fluids. The key statement of this paper is that the diameter exponents "do not vary significantly from . . . -1.20." In statistical terms, this says that the m value for each fluid, which was obtained from all the measurements made on that fluid. has not been shown to be different from the arithmetic mean of the m values for the 16 fluids tested. This implies that the group mean, -1.20, is a more reliable value to use for an individual fluid than is the m value derived from the data on that fluid alone. No statistical test is described to support the key statement that the diameter exponents do not vary significantly from -1.20. Such a test would have to take into account that each individual m value is shown to correlate the pressure gradients for its fluid, with only about 3 percent standard deviation over the diameter range covered. That is, the m value is not the result of a single independent measurement. Thus, it would not be sufficient, or valid, to compare the deviation of one of the m values with the variance of the 16 values of m about their mean. An alternative interpretation of the key statement is that the diameter exponents do not vary appreciably from -1.20; i.e., that using -1.20 does not cause serious inaccuracy. Table 2 seems to be offered in support of such an assertion. However, such a statistical treatment (1) is unnecessary and (2) cannot lead to any valid scale-up generalization. The amount of error introduced by using a 1"wrong" value of diameter exponent — i.e., -1.20 instead of m — is determined by Eq. 6. The ratio of the pressures predicted by Eqs. 6 and 20 for scale-up from ds in small pipe to d, in casing is The pressure for 30-percent calcium carbonate slurry (m = -1.112) in 10-in. ID pipe would be predicted 30 percent higher by Eq. 6 than by Eq. 20, if based on tests in 0.5-in. ID pipe. The data set tested in Table 2 represents only a limited sample of pipe diameters (ratio of about 4:l) out of the population of diameters that would

Jan 1, 1970

By S. G. Lasky

W E seem to have assumed the careless habit in recent years of treating mining geology as synonymous with exploration geology, and exploration synonymous with exploration for new deposits-to be forgetting that mining geology includes also the geologic control or guidance of day-by-day mining operation. In the publicized romantic spotlight of the search for new deposits, we forget the man with the dirty over-alls, grubbing away at the daily tasks of finding new shoots and of helping to keep production up and cost down. During 1949, as in previous years, the resident geologist continued his quiet efficient functioning while the exploration geologist continued to stay in the spotlight-although this time he shared it with what may be called the resource-appraisal geologist. Many broad problems of national import such as tax modification, the operations of the Economic Cooperation Administration, and certain international relations have come up against an unexpected factor lurking in the background, namely, appraisal of world and domestic reserves and latent resources. T. M. Broderick opened the year with his address as retiring president of the Society of Economic Geologists, wherein he analyzed the problems of exploration geology listing among them "the shortcomings of the geologists themselves, of the educators, the mining companies, our Published by permission of the Director, U. S. Geological Survey. technical publications, the Federal Survey and Bureau of Mines, and the property owners."

Jan 1, 1950

By S. J. Kidder, G. C. McCartney

THE Helen Mine, of the Algoma Steel Corporation, in the Michipicoten district, Ontario, Canada, has produced more than 6,240,290 tons of iron ore. Prior to and during World War I, 2,823,369 gross tons of brown ore were shipped, and from 1939 to the end of the 1944 season, 3,416,921 gross tons of siderite ore were produced from open-pit operations. Brief descriptions are given of the nature of the ore, the mining methods employed and the manner of treatment of the ore. Shipment of the finished product, known as Algoma sinter, is made to blast furnaces in both Canada and the United States. The iron-ore bodies-i.e., the oxide ores of the Old Helen and the siderite of the New Helen-are a part of a tabular shaped area of iron formation that extends over a length of more than 10,000 ft. and has a maximum width of 1000 ft. The ores are considered to be a product of introduction of iron-bearing material accompanied by replacement of the rocks already present. It is shown that introduction took place subsequent to the development of the major folded structures. It is believed the iron-bearing material emanated from an igneous source.

Jan 1, 1946

[Trans. No. Place Date Vol. Page 1, Wilkes-Barre, Pa.* .... May, '71.. 1 3 2. Bethlehem, Pa Aug., '71.. 1 10 3 Troy, N. Y Nov.,'71.. 1 13 4. Philadelphia, Pa Feb., '72.. 1 17 6. New York, N. Y •.... May, '72.. 1 20 6. Pittsburgh, Pa..:.Oct., '72.. 1 25 7. Boston, Mass Feb., '73.. 1 28 8 Philadelphia, Pa.' May, '73.. 2 3 9. Easton, a Oct., '73.. 2 7 10. New York, N. Y Feb., '74.. 2 11 11. St. Louis, Mo.* May, '74.. 3 3 12. Hazleton. Pa Oct.. '74.. 38 13. New Haven, Conn Feb., '75.. 3 15 14. Dover, N. J.' May, '75.. 4 3 16. Cleveland, 0 Oct., '75.. 4 9] [ ]

Jan 1, 1925

The General Electric Co., in cooperation with the Montana School of Mines and under a research grant from the Anaconda Co., is presently experimenting on a new non-explosive method of breaking rock with radio-frequency electrical power. The method is known as electrothermal forcing. It must be understood that present equipment has not been designed to perform primary blasting functions. Its conceived use will be restricted to small pieces of rock too large to pass through a chute or grizzly. However, even this use is still far in the future. Experiments to date have been limited mostly to rock smaller than 18 in.

Jan 11, 1961

By Stuart Croasdale

NOT long ago I was called upon to conduct some experiments on the treatment of ores from the New Cornelia copper mine, Ajo mountains, Arizona, for the Calumet & Arizona Copper Co. The problem was a very interesting one and contained some unusual features. Incidental with this problem was the utilization of a large amount of low-grade pyrite in the Bisbee mines of the company, provided this could be accomplished by any feasible method. The New Cornelia mine is situated 45 miles south of Gila Bend, the nearest railroad point, on the Southern Pacific Railroad. It is about 160 miles, almost due west, from Tucson. This section is one of the most arid in the United States. The normal annual precipitation, as given by the United States Weather Bureau covering a period from 1870 to 1901, is 3 to 5 in. During June and July, 1913, the records kept by the company gave the following results. These are all I have available, but they show the enormous evaporation that can be expected, which may be a factor in leaching operations on a large scale.

Jan 8, 1914

By R. J. Wasilewski

The variation of elastic modulus with terrzperature between -150° and 600°C has been investigated. Compounds close to equiatomic cornposition exhibit very low modulus values and very high damping near room temperature. The modulus rises steeply with both decreasing and increasing temperature. The modulus minimum and the high damping are believed to be connected with a martensitic transformation of TiNi. In bulk material this transition takes place slightly above room temperature quite rapidly and reversibly, with a hysteresis of some 30°C, depending on the Ti:Ni ratio. Oxygen impurity affects the reaction time. THE inter metallic compound TiNi has been reported to exist in an ordered CsCl (B2) structure,l-6 the homogeneity range varying rather markedly with temperature.7 Some investigators reported this compound to decompose peritectoidally to Ti2Ni and TiNi, between 650° and 800°C,3 or below,',g the latter workers also suggesting the decomposition to be strain-sensitive. Purdy and Parr were the first to report a structural transformation to a new, possibly hexagonal, structure at 36°C,7 a temperature indubitably too low to allow the significant amount of diffusion necessary for a peritectoid reaction. Mechanical-property investigations of compositions close to TiNi just above room temperature have qualitatively shown remarkable anomalies, particularly with respect to clamping,' and to a "memory" effect, that is, plastically deformed material returning to its original shape on being heated through the "decomposition" temperature.9 The original explanation of this effect—based on the apparent experimental observation of Ti2Ni or TiNi, formation in the material subjected to tensile or compressive stresses, respectivelp—does not appear plausible. It appeared more probable that the change involved may be a martensitic, diffusionless structural transformation, similar to those observed in other B2 structures such as 0 brass,'' AuCd,ll and AuZn.12 The existence of such transformation has been established recently,', although the symmetry of the low-temperature structure is not yet known. The present paper describes the elastic modulus and damping behavior of polycrystalline TiNi in both structures. EXPERIMENTAL METHOD 1) Specimens. All the specimens to be investigated were prepared from premelted electrolytic nickel and iodide titanium by nonconsumable arc melting and casting in a water-cooled copper mold. The cast billets were canned in mild steel, extruded, and swaged to approximately 0.375 in. diam. The cans were then removed by pickling or machining. Preliminary material balance checks indicated no significant weight losses on melting (less than 5 mg on a 50-g button); hence nominal compositions have been used throughout. In agreement with previously reported observations7 no single-phase material was obtained at—or close to—Ti 1.00 Ni1.00 a small amount of finely divided second phase always being present. It was found that most of the oxygen impurity was associated with this minor phase, which was identified as oxygen-bearing Ti2Ni—possibly Ti,Ni,O. The amount of this phase—at any given Ti:Ni composi-

Jan 1, 1965

By H. C. Schultz

CERTAIN local conditions were known to govern in large measure the successful adaptation of liquid-oxygen explosives to the large-scale blasting at Chuquicamata. The wide variation in hardness of the rock at this mine makes necessary the use of several types of explosives. A locally manufactured, relatively cheap black powder is used in blasting the softer waste and capping material, where a thorough displacement, breaks the ground sufficiently. Before the introduction of L. 0. X., an ammonia dynamite of about 65 per cent. strength was being used exclusively in the harder underlying orebody, where a strong disruptive as well as a displacement effect is required for breaking the ore. The L. 0. X., as developed for quarry work in the United States, has a practically pure carbon cartridge material, and the explosive has an extremely high rate of detonation, which should therefore cause it to usefully develop its full disruptive effect in hard ground. The individual blasts at Chuquicamata are large, black-powder shots which dislodge masses of rock averaging 250,000 tons each, and dynamite shots which dislodge masses averaging 80,000 tons each. It was desirable, therefore, to attempt to displace with L. 0. X. the faster, higher-cost ammonia dynamite used in the smaller blasts. It was not considered practical to attempt to displace the low-cost black powder with L. 0. X., as estimated costs showed no probable saving if this were accomplished. Since it was desirable to continue shooting relatively large blasts for effective operation, it was recognized that larger storage facilities than had been in use would be needed for the liquid oxygen. Because of the difficulty of transporting and discharging large storage containers of efficient design, the better plan appeared to be storage and discharge of the liquid at the place of manufacture, and transportation of the filled soaking boxes to the blast.

Jan 1, 1928

By Alfred H. Bell, Virginia Kline

In 1944, Illinois produced 77,413,000 bbl. of oil, or 4.6 per cent of the total for the United States, and continued to rank sixth in the nation in oil production. This represents a decrease of 6 per cent from 1943, when- the total Illinois production was 82,256,000 bbl. This decrease was much less than the 23 per cent decrease in 1943 from production of the previous year. The principal factor in arresting the production declinc, which had been going on since 1941, seems to be the increased drilling that followed the relaxing of the Federal Government's rules in regard to well spacing. The daily average production for 1944 was approximately 212,000 bbl. Daily averages by months were as follows: Jan......... 219,000 July........ 206,000 Feb......... 220,000 Aug......... 211,000 Mar........ 216,000 Sept......... 209,000 Apr......... 211,000 Oct......... 210,000 May........ 213,000 Nov........ 209,000 June........ 209,000 Dec......... 205,000 During the year, 1991 wells were drilled for oil and gas in Illinois as compared with 1791 in 1943, an increase of II per cent. Of the 1991 wells, 430 are classified as "wildcat" as compared with 461 in 1943. Twenty-eight new pools (Table 2 A) were discovered in 1944 as compared with 29 in 1943. Changes in federal drilling regulations, permitting closer spacing of wells, resulted in a drilling program that emphasized development of proved acreage rather than wildcatting. Data on production and drilling by fields are given in Table I; data on annual production and drilling for Illinois, in Table 3. Discoveries Twenty-eight new fields (Table 2 A), 42 extensions (Table 2 B), and 39 additional producing zones in existing fields (Table 2 C) were discovered in 16 counties in Illinois during 1944. Of the 28 new fields, one was abandoned during the year, 14 were one-well fields, eight others had not more than 6 wells, one had 8, one had 9, one had 11, one had 15, and the largest new field, Roaches North, had 28 producing wells at the end of the year. In all, 109 wells were producing in these new fields on Jan. 2, 1945, as compared with 111 wells producing from 29 new fields at the end of 1943. . The average initial production of the discovery wells of the 28 new fields was 129 bbl. of oil and II bbl. of water, a notable decline from the average initial production of 194 bbl, of oil and 15 bbl. of salt water for the 1943 discovery wells. In fields discovered since 1936, the total number of oil wells producing at the end of 1944 was 12,335. Productive Acreage The area of proved production in the new fields (discovered since 1936) increased from 144,335 acres at the end of 1943 to 173,485 acres at the end of 1944 (Table I), an increase of 29,150 acres. Of this increased area, 1720 acres are in fields discovered during 1944 and 27,430 acres are in extensions of fields discovered earlier.

Jan 1, 1945

By Tomek Ulatowski

This presentation discusses the necessary ingredients for the creation of an acceptable credit structure, i.e., the structure that enables the borrower to attract the funding from different groups of lenders. As the amount of debt in the capitalization of new projects increases, it becomes quite critical that the mining venture sponsors obtain funding in a manner which maximizes the project economics. Attention normally is focused on the inherent operating cost characteristics of a venture such as the cost of mining, milling, transportation, smelting, and refining. The projected costs are derived from lengthy feasibility studies often taking millions of dollars and years to prepare. For a variety of reasons as the amount of equity directly provided by the sponsors declines, the balance must be made up from external credit sources. As a result, once the project becomes operational, debt service requirements assume crucial importance. For most new ventures, in the early years of production, the total amount of periodic debt amortization charges together with the projected interest expenses equals or exceeds the total operating cost. Utmost care must be taken, therefore, to reducing these costs which will then increase the chances for the implementation of the project. Project sponsors must carefully evaluate different funding sources in terms of their potential economic impact and, concurrently, evaluate alternative credit structures in order to be able to attract the selected funding vehicles. In this presentation I will discuss credit sources in the order of their relative appeal; i.e., from the standpoint of maximizing rates of return to the project owners. The tenor of the credit, that is the period from signing a loan agreement to the time of last repayment under the loan agreement, is undoubtedly the most important variable in evaluating the attractiveness of debt sources. Therefore, I will begin by discussing debt sources with the longest maturities and will end with a description of credits with relatively shorter tenors. The availability of different funding possibilities will naturally depend on the geographic location of the proposed venture, the creditworthiness of the borrower and the sponsors, the project economics, and finally the actual liquidity conditions in the capital markets at the time that the funds are committed. U.S. LONG-TERM DEBT MARKET - PUBLIC OFFERINGS AND PRIVATE PLACEMENTS The long-lived nature of most mining projects dictates that the majority of the mine financing be raised from long-term sources. In today's world capital markets U.S. debt issues probably carry the longest maturities available. The maturities can range from 5 to 40 years. Various types of long-term corporate debt instruments can be differentiated from one another by their terms, seniority as to claims against the assets of the issuer, legal form, and whether issued privately or through a public offering. The terms of these debt issues vary widely. For example, the interest rate which is typically fixed at the time of issuance, is determined by the credit quality of the issuer, the maturity, the average life, the seniority of the debt, the quality of control covenants or type of assets pledged as security, and other exogenous factors such as: economic policy, general level of interest rates and cur-rent level of financing activity. The entire principal amount of the debt may be due and payable at maturity (known as a "bullet" maturity) or, more typically, through periodic repayments in equal or staggered amounts. Almost all such debt issues allow for prepayment at the option of the issuer, but require varying amounts of repayment penalties. Disbursements are made over a relatively short period after signing of the debt documentation which may not coincide with the actual funding needs of the project. Financial covenants can be quite stringent, covering areas such as the issuer's financial leverage, working capital, payment of dividends and other distributions, merger and acquisition activities, and limitations on the disposition of property. Long-term debt issues may also be distinguished by the seniority of their claims against

Jan 1, 1985

By AIME AIME

Adjustable Pyrometer-Stand. By L. W. BAHNEY, xxxvii, 33. Agency of Manganese in the Superficial Alteration and Secondary Enrichment of Gold-Deposits in the United States. By WILLIAM H. EMMONS, xlvi, 767. Application of Descriptive Geometry to Mining-Problems. By JOSEPH W. ROE, xxxix, 173. ARNOLD, C. EVERARD. The Giroux Shaft at Kimberly, Nev., xlii, 461. BAHNEY, L. W. An Adjustable Pyrometer-Stand, xxxvii, 33. BALL, SYDNEY H., and SHALER, MILLARD K. Mining-Conditions in the Belgian Congo, xxxix, 253. BEALS, ROGER L., and TWEEDY, GEORGE A. Cyanide-Plant and Practice at the Minas del Tajo, Rosario, Sinaloa, Mexico, xxxviii, 123.

Dec 1, 1910

By Charles R. Cavanaugh, John F. Elliott

The activity of nickel in liquid Pb-iVi alloys which are rich in lead was measured in the temperature region of 700° to 1100°C by means of the galvanic cell: The electrolyte used was stabilized zirconia. Tlze data were correlated using the a function, and a plot of the temperature coefficient aE/aT All subsequent calculations of the thermodynamic properties are based on these two functions. The activity, activity coefficient, and molar properties of mixing of nickel are reported. Nicke1 shows extreme positive deviations frorn ideality while lead shows a very slight positive deviation in the composition range studied The study of the activity of nickel in liquid Pb-Ni alloys reported herein was undertaken to explore the use of stabilized zirconia, an oxygen-ion electrolyte, with liquid-metal electrodes, and to obtain further information on the thermodynamic properties of the liquid binary Pb-Ni system. The cell The reversible electromotive force of the cell results from the difference in the chemical potential of the oxygen at the two electrodes: po, (left) - p~ (right) = -4E5 [I] The chemical potential of oxygen on the right is fixed by the activity of nickel in the solution and pure solid nickel oxide. That on the left is set by pure solid nickel in equilibrium with pure solid NiO. By definition: Since the chemical potential of nickel is related to the chemical potential of oxygen through the equilibrium constant for the formation of NiO from nickel and oxygen gas, the electromotive force of the cell is also expressed In this case, n is 2, E is the reversible potential of the cell, and 5 is Faraday's constant. The work of Kuikkola and wagnerl and Schmalz-reid2 has shown that the stabilized zirconia electrolyte is essentially an ionic conductor at the oxygen levels encountered in the experimental arrangement of the work, i .e., PG > 10-l7 atm. THE EXPERIMENTS The advantage of this type of reversible cell over those using a liquid electrolyte is the simplicity arising because the electrolyte also functions as one of the containing crucibles. A further simplification was the choice of the Ni (sat.)-NiO electrode as the standard. This permitted a ready check on the behavior of the electrolyte, as the potential of the cell must become zero when the right electrode becomes saturated with nickel, either because of a change of temperature or because of the addition of nickel to the electrode. It also permitted the potentials being measured to lie in the most satisfactory experimental range of 0 to 100 mv. Although it was not theoretically necessary, lead was included in the standard electrode as it assured good contact between the electrode and electrolyte. Cell Design. The general arrangement of the experimental cell assembly is shown in Fig. l(a) and the details of the cell itself are contained in Fig. l(b). The anode lead wire on the interior of the cell was connected to a coil of perforated sheet nickel. Within this coil were nickel oxide pellets which were held beneath the surface of the liquid Pb-Ni alloy. A disc of nickel oxide was held at the bottom of the external crucible (alumina) by means of the thermocouple protection tube. The nickel oxide disc and pellets were compressed dry at 10,000 psi and sintered at approximately 1000°C for an hour in air. A major experimental difficulty of reversible electromotive force cells with liquid electrodes is the selection of suitable materials for connecting

Jan 1, 1964

By C. O. Burgess, W. D. Forgeng

The results of an investigation of the ternary system iron-chromium-silicon were reported in 1936 by the present authors.l Partly for the sake of theoretical interest, and partly because of the possible commercial importance of these alloys, the present investigation was undertaken to determine the effect of some of the commoner elements likely to occur, deliberately or otherwise, in such alloys if made on a commercial scale. The elements thus added were carbon, nickel or manganese. The alloys studied were, therefore, parts of quaternary systems. This investigation was concerned primarily with the effect of these additional elements on the alpha-iron phase and the boundary between this phase region and the alpha plus sigma two-phase region. The sigma phase is a ternary solid solution based upon the compound FeCr. The work was performed mainly by X-ray methods, but a number of microscopic examinations were also made and are reported. While isolated alloys in the composition ranges studied may have been discussed in metallurgical publications, no systematic investigation of any assistance to us was found. Of the earlier work, the investigations on the iron-chromium-carbon system and on the chromium carbides by Westgren and his coworkers2'3 enabled us to identify the carbide phase. Several articles appeared after the present experimental work had been completed. Lucas and Wintrup4 determined the solubility of carbon in molten iron-chromium-silicon alloys. Tofaute and his coworkers5'6 have made detailed studies of the iron-chromium-carbon system, which will be referred to later. Materials and Methods Materials.—The iron, chromium and silicon used were essentially the same as those used in the investigation of the ternary system.l The

Jan 1, 1938

By C. O. Burgess, W. D. Forgeng

The results of an investigation of the ternary system iron-chromium-silicon were reported in 1936 by the present authors.l Partly for the sake of theoretical interest, and partly because of the possible commercial importance of these alloys, the present investigation was undertaken to determine the effect of some of the commoner elements likely to occur, deliberately or otherwise, in such alloys if made on a commercial scale. The elements thus added were carbon, nickel or manganese. The alloys studied were, therefore, parts of quaternary systems. This investigation was concerned primarily with the effect of these additional elements on the alpha-iron phase and the boundary between this phase region and the alpha plus sigma two-phase region. The sigma phase is a ternary solid solution based upon the compound FeCr. The work was performed mainly by X-ray methods, but a number of microscopic examinations were also made and are reported. While isolated alloys in the composition ranges studied may have been discussed in metallurgical publications, no systematic investigation of any assistance to us was found. Of the earlier work, the investigations on the iron-chromium-carbon system and on the chromium carbides by Westgren and his coworkers2'3 enabled us to identify the carbide phase. Several articles appeared after the present experimental work had been completed. Lucas and Wintrup4 determined the solubility of carbon in molten iron-chromium-silicon alloys. Tofaute and his coworkers5'6 have made detailed studies of the iron-chromium-carbon system, which will be referred to later. Materials and Methods Materials.—The iron, chromium and silicon used were essentially the same as those used in the investigation of the ternary system.l The

Jan 1, 1938

By W. G. Matteson

BENJAMIN L. MILLER, So. Bethlehem, Pa.-In discussing the question personally with Mr. Matteson I have found that he simply proposed this as a suggestion and he recognizes, as well as a great many other oil geologists and oil operators, that to put into practice such a suggestion would mean the overcoming of many difficulties. Yet perhaps it may be possible to overcome the various objections that may be offered. Undoubtedly one of the most serious objections is that of incomplete and inaccurate well records. Faulty records are worse than no records at all. Perhaps, however, definite instructions and insistence on their observation may remedy this defect after a time. THE CHAIRMAN (M. L. REQUA, San Francisco, Cal.).-This subject is a. very important one, but just how far the National Government can go in .taking action is a question: It involves, of course, the question of State rights. California, I .think, has done very well up to date and probably will do better in the future. The law that was passed at the session of the Legislature 2 years ago is working as satisfactorily as anything of that kind can work with so little experience to guide the framers of the statute. We recognize in California the vital necessity of conserving the oil of the State. We have come to the conclusion that there is not as much oil ,in California as we thought there was. In the month of December the State drew on its oil stocks to- the extent of 1,800,000 bbl. and I think that the January statistics will show probably as much more. There is more or less of a.: panic at the present time among the large marketing concerns regarding the question as to where they are going to get their oil for future requirements

Jan 4, 1917

By Guy W. Crane

The geology of the Tintie mining district, fully treated, would occupy an elaborate monograph. This less comprehensive paper is devoted primarily to the occurrence and origin of the orebodies of the district, while space is given to those phases of the general geology only which seem necessary to a proper setting of such a discussion. The first geological report on the Tintic district to be issued was that by Tower and Smith, published in 1899, in the form of a paper in Part III of the Nineteenth Annual Report of the U. S. Geological Survey, and also as Folio No. 65, Geologic Atlas of the United States. About four years ago a second investigation was begun by Waldemar Lindgren and G. F. Loughlin, of the U. S. Geological Survey. With the exception of a paper on the oxidized zinc ores of the Tintic district by Mr. Loughlin, the results of their work are still unpublished. The writer's acquaintance with the district began in the fall of 1913, and has extended over a period of about two years. 1. Location The Tintic district lies about 65 miles due south of Salt Lake City, and on the west central slope of the Tintic Mountains, a short range, which forms the connecting link between the Oquirrh Mountains on the north and the Canyon Range on the south—the group constituting the first of the Basin ranges to the west of the Wasatch Mountains. The productive portion of the district embraces an area about 6 miles long and 2 miles wide, which is divided between Juab and Utah Counties. Within this area are the towns of Eureka, Mammoth, Robinson, Silver City, and Knightsville. All these points are tapped by the Denver & Rio Grande and S. P., L. A. & S. L. Railways. 2. Topography As in most of the Basin ranges, topographic relief is strong, dropping rapidly from peaks of 8,100 ft. above sea level to elevations of 5,600 ft. in Tintic Valley on the west and 4,500 ft. in Goshen Valley on the east.

Jan 1, 1916

Organization Place Date 1918 National Society of Naval Architects New York, N. Y. Nov. 14-15 American Society of Mechanical Engineers New York, N. Y. Dec. 3-6 Geological Society of America Boston, Mass. Dec. 28-31 American Association for the Advancement of Science Boston, Mass. Dec. 27¬ Jan. 2. 1919 American Society of Civil Engineers New York, N. Y. Jan. 15-16 American Wood Preservers Association St. Louis, Mo. Jan. 28-30 American Society of Heating and Ventilating Engi¬ neers New York, N. Y. Jan. 28-30

Jan 11, 1918

By Robert H. Hafner, Irvin R. Kramer

In recent years considerable interest has been shown in surface-alloyed metals, particnlarly those of chromium (chromized steels), which have excellent corrosion resistance under a variety of severe conditions, and may undergo bending and flanging operations without spalling. An early method1 employed to produce a high-chromium case on steel was developed by Kelley in 1921. It consisted of heating a low-carbon steel in intimate contact with powdered chromium in the presence of hydrogen at temperatures sufficiently high to permit diffusion of chromium into the steel. The usefulness of this process was limited because the extremely high tem- peratures of 1200º to 1400ºC. (2200° to 2550°F.) caused excessive grain growth and warpage. Louenstein and Ulmer2 packed iron castings in ferrochromium and com- mon salt, and heated for approximately three hours at 930º to 1040°C. (1700º to 1900ºF.). A recent and more practical method of depositing chromium on steel surfaces has been developed in Germany by Daeves, Becker and Steinberg3-8 and in Russia by Izgaryshev and Sarkisov.9 This process consists of passing gaseous chromium chloride over the steel to be chromized at temperatures of 900º to 1000ºC., or packing them in a porous, ceramic material that previously had been saturated with chromium chloride. They reported obtaining a Chromized layer, 0.004 in. thick, on low-carbon steels. Later, Daeves4 established a relationship between the carbon content

Jan 1, 1943

By Robert H. Hafner, Irvin R. Kramer

In recent years considerable interest has been shown in surface-alloyed metals, particnlarly those of chromium (chromized steels), which have excellent corrosion resistance under a variety of severe conditions, and may undergo bending and flanging operations without spalling. An early method1 employed to produce a high-chromium case on steel was developed by Kelley in 1921. It consisted of heating a low-carbon steel in intimate contact with powdered chromium in the presence of hydrogen at temperatures sufficiently high to permit diffusion of chromium into the steel. The usefulness of this process was limited because the extremely high tem- peratures of 1200º to 1400ºC. (2200° to 2550°F.) caused excessive grain growth and warpage. Louenstein and Ulmer2 packed iron castings in ferrochromium and com- mon salt, and heated for approximately three hours at 930º to 1040°C. (1700º to 1900ºF.). A recent and more practical method of depositing chromium on steel surfaces has been developed in Germany by Daeves, Becker and Steinberg3-8 and in Russia by Izgaryshev and Sarkisov.9 This process consists of passing gaseous chromium chloride over the steel to be chromized at temperatures of 900º to 1000ºC., or packing them in a porous, ceramic material that previously had been saturated with chromium chloride. They reported obtaining a Chromized layer, 0.004 in. thick, on low-carbon steels. Later, Daeves4 established a relationship between the carbon content

Jan 1, 1943

By Robert H. Hafner, Irvin R. Kramer

IN recent years considerable interest has been shown in surface-alloyed metals, particularly those of chromium (chromized steels), which have excellent corrosion [ ] resistance under a variety of severe conditions, and may undergo bending and flanging operations without spalling. An early method' employed to produce a high-chromium case on steel was developed by Kelley in 1921. It consisted of heating a low-carbon steel in intimate contact with powdered chromium in the presence of hydrogen at temperatures sufficiently high to permit diffusion of chromium into the steel. The usefulness of this process was limited because the extremely high temperatures of 1200° to 1400°C. (2200° to 2550 F.) caused excessive grain growth and warpage. Louenstein and Ulmer2 packed iron castings in ferrochromium and com- [ ] mon salt, and heated for approximately three hours at 930° to 1040°C. (1700° to 1900°F.). A recent and more practical method of depositing chromium on steel surfaces has been developed in Germany by Daeves, Becker and Steinberg3-8 and in Russia by Izgaryshev and Sarkisov.9 This process consists of passing gaseous chromium chloride over the steel to be chromized at temperatures of 900° to 1000°C., or packing them in a porous, ceramic material that previously had been saturated with chromium chloride. They reported obtaining a chromized layer, 0.004 in. thick, on low-carbon steels. Later, Daeves4 established a relationship between the carbon content

Jan 1, 1942