Search Documents

By Rudolf Gahl

Some time ago the Detroit Copper Mining Co. had to decide the question whether it would pay to re-treat slime-tailings, and several machines were tested in order to ascertain the type of construction which would give the greatest saving. In previous tests on the ore of this company, several tables proved far inferior to the Frue vanner, and for this reason they did not receive any serious consideration. In the late tests, however, one table was found to surpass the vanner in the percentage of saving made. The Frue vanner used in these tests had been adjusted approximately to the slope which the slime-vanners in the concentrator of the Detroit Copper Co. had at that time, about 2 in. between the inside of the wooden posts, or 0.272 in. per ft. It had not been determined, however, if this slope was the most economical one for treating the slime-feed in the mill, or for re-treating the tailings from the slime-vanners, and I was instructed to ascertain by test-runs, under different conditions, the best adjustments for the work to be done. In order to determine if a change in the adjustments of the machines would improve the results, it seemed sufficient to continue running the tests between the vanner and the table before mentioned, keeping the feed and all other conditions the same, but varying the adjustments of the vanner from run to run. I employed a vanner-man of long experience to operate these machines, who expressed the opinion that a slope between 28 and 2.5 in. between the posts (0.323 and 0.340 in. per ft.) would give the best results. Some runs made this way gave a considerable improvement. While for a slope of 2 in. (0.272 in. per ft.) the saving had been only 40.5 per cent. of that of the table, it was 49.2 per cent. for 2.5 in. (0.340 in. per ft.) slope. A decrease of

Jan 1, 1910

By W. C. Ellis, E. S. Greiner, M. E. Fine

Discontinuous changes of Young's modulus, internal friction, coefficient of expansion, electrical resistivity, and thermoelectric power are evidence for a transition in chromium near 37OC. Although the X-ray diffraction pattern gives no clue, a difference between the thermal expansivity and the temperature dependence of the lattice parameter suggests a crystal-lographic change. Young's modulus data disclosed another transition near THE thermal dependence of a number of proper- ties of chromium indicates a transition occurring over a temperature range near room temperature. Bridgman' noted this first from a minimum in the electrical resistivity near 12°C. In a sample of greater purity, Sochtig' observed the minimum at 41 °C. Erfling3 reported an inflection in the thermal expansivity curve at 36°C. These temperature-dependence curves are reversible with no hysteresis being detected. No discontinuity or inflection has been observed in the heat capacity' or the paramagnetic susceptibility.' Likewise, no one has noted a change in crystal symmetry. In the present investigation Young's modulus, internal friction, coefficient of expansion, electrical resistivity, illustrated in Fig. 1, lattice constant, Fig. 2, thermal electromotive force, Fig. 3, and paramagnetic susceptibility, Fig. 4, were measured over an extended temperature range. The samples were prepared in two ways: (1) By cold pressing a sintered electrolytic powder compact,' and (2) by electroforming from an aqueous solution. The electroformed samples were prepared by R. A. Ehrhardt and G. Bittrich by plating on copper or nickel tubes from an aqueous solution according to the method of Brenner, Burkhead, and Jennings.' The pressed powder samples (method 1) were finally annealed at 1400°C in purified helium: the electroformed samples, packed in powdered chromium, were vacuum-annealed at 1000°C. From the composition of the original powder' the purity of the pressed powder samples is estimated to be 99.8 pct Cr. Spectrochemical analysis furnished by E. K. Jaycox, revealed only slight traces of impurities in the electroformed sample (less than 0.001 pct), neither iron nor nickel being detected. Chromium deposited by this method is reported to contain approximately 0.05 pct 0.- Methods and Data Young's Modulus: For measurement of Young's modulus, an annealed, pressed powder sample, 0.114 x0.237x1.845 in., and an electroformed sample, 0.10 in. od, 0.01 in. id, and 1.86 in. long, were prepared. The resonant frequencies of the rod samples in forced longitudinal vibration were measured at a series of temperatures from —192" to 200°C by a method previously de~cribed.6,7 Because the samples were nonferromagnetic, iron- silicon or molybdenum permalloy tips (0.013 in. thick) were soldered to the ends. The softening temperature of the solder limited the temperature of measurement. Young's modulus, E,, of chromium at temperature, T, may be calculated from the resonant frequency of the composite rod, f,; the thickness of the tips, t; the length of the chromium sample at 25°C, l,.; the density of chromium at 25°C, pc (7.20 g per cc);5 and the thermal expansivity, Al/l25. Modulus differences for two temperatures, ET and E, are accurate to +0.002x10" dynes per cm2. ET = 4PAlc+2tyf Young's modulus at 25°C, Fig. la, is 28.2~10" dynes per cm' (40.8xlO" si) in wrought chromium (upper curve). The modulus of the electroformed sample is apparently lower due to cracks. From the modulus measurements two transitions were observed: one with a critical temperature at 37°C, the other at —152°C. Internal Friction: The internal friction, 1/Q, was determined from the width, Af, of the strain amplitude-frequency curve at 0.707 times the strain amplitude at resonance;' the internal friction, 1/Q, then equals Af/f. Fig. lb shows a sharp peak in internal friction at 38°C. The internal friction of the electroformed sample had a similar maximum. Thermal Expansion: The expansivity measurements, shown in Fig. 2, covering the temperature range —195" to +400°C were made by D. MacNair in an interferometric dilatometer8 sing a sample consisting of three pyramids 0.25 in. high prepared from wrought electrolytic chromium. Below —120°C the experimental points deviated up to ±2x10 from the drawn expansivity curve in Fig. 2 because of decreased precision of the quartz wedge thermometer at low temperatures. Near 38°C the thermal expansivity curve, Fig. 2, goes through an inflection corresponding to a minimum in the coefficient of expansion, Fig. ld, and a relative volume decrease on heating. Electrical Resistivity: The variation of electrical resistivity with temperature measured by the po-tentiometric method is also shown in Fig. l. The resistivity of the wrought chromium (upper curve) at 20°C is 13.6 microhm-cm; of electroformed chromium (lower curve) 12.8 microhm-cm. The lower value reflects higher purity and agrees closely with a published value." A minimum at 40°C occurs in the resistivity curves of both samples. No conclusive evidence for a transition near — 150°C was observed, but the points, Fig. 1, appear to deviate from a smooth curve between —120" and —160°C.

Jan 1, 1952

By Hugh Neill, O&apos

In previous papers,' the author has reported the results of experiments on the straining in tension of a single-crystal test piece, about 0.6 in. long, of vacuum-melted electrolytic iron containing 1.8 per cent. of silicon. The crystal was originally in the "as cast" condition, and was stressed slowly along a tetragonal axis so that slipping along conjugate gliding planes finally transformed the original cylindrical portion into a pair of fracture wedges. One of these fracture wedges was sectioned along the stress axis in a plane at right angles to the edge of the wedge. A metallographic study of this plane of section led to the conclusion that slip had taken place in the (111) direction along (112) planes making a V shape with the stress axis. The present paper describes the results of scratch-hardness tests conducted on the same section, in order to determine the distribution of strain hardness therein, followed by annealing, and considers the resulting variations in hardness. These observations supplement those made by Krivobok2 on similar material reduced 25 per cent. by hammering (i. e., by impact) in the cold. In order to investigate ageing effects, two small crystals of the same alloy were also tested. The Specimens Employed The principal specimen, A, was prepared for the metallographic examination leading to the determination of the slip planes of the crystal. Therefore the work described in this paper was conducted on metal which had been repeatedly etched and had been allowed to rest for about 30 months after straining. It consisted of a section of the fracture wedge and contiguous unstrained head of the test piece taken along a tetragonal axis parallel to the direction of stressing, the plane of section originally being not far removed from the (011). Several subsequent grindings

By C. G. Dunn, F. W. Daniels, M. J. Bolton

Recent observations on grain boundary movements in sihcon iron have indicated the possibility of studying grain growth phenomena in two-grain specimens in which several variables affecting growth are readily controlled. These variables are (1) the energy per unit area (?) in the grain boundary, (2) the orientation relationship of the two grains, and (3) the radius of curvature (7) of the moving boundary. Ideally, one grain A should be a narrow rectangular parallelepiped adjacent to a second grain ß as shown two dimensionally in Fig 1. Such a two-grain group becomes unstable when one end of grain A is shaped according to the dotted line. Since the width w of grain A remains constant during growth of grain B, T should also remain constant. The other vari- ables mentioned above can be controlled in the preparation of each two-grain specimen.l,2,3 For a parLicular orientation of each grain, is not necessarily fixed; ? may also depend on the orientation of the grain boundary, but this may be controlled to some degree. The energy relationships for the gowth of grain ß may be derived from the more simple arrangement of two grains A' and B' shown schematically in Fig 2. Here B' largely surrounds A'. Assume these grains are oriented with a common plane parallel with the flat

Jan 1, 1950

By H. H. Hausner, H. S. Kalish

IN recent years zirconium and beryllium have become of great interest because of their special properties. Zirconium is known for its remarkable ability to absorb the gases oxygen, nitrogen and hydrogen, has extensive use as a getter in electron tubes and has indeed become the primary metal in the manufacture of photoflash bulbs. Beryllium is of interest because it is light metal and as such could supplement aluminum and magnesium in light metal applications. The late development of zirconium ductile at room temperature produced by both the iodide and calcium reduction methods has stimulated frequent articles on this metal in the recent literature. Beryllium is so closely akin to zirconium crystall-ographically that some investigators are of the opinion that beryllium should be ductile at room temperature if it were pure enough. The crystallographic relationship of beryllium and zirconium, the interest created in Be-Zr alloys where the zirconium is believed to function as a remover of solid solution gas in beryllium and thus increase the ductility of the beryllium rich alloy, and the amenability of these metals to powder metallurgy methods stimulated this approach to an investigation of the system Be-Zr. Preliminary work showed that a zirconium compact melted when pressed in contact with a beryllium compact and sintered at 1250°C, without any apparent final bond between the two. A search of the literature revealed nothing pertinent about the Zr-Be system or about any zirconium - beryllium alloys. In 1936 Misch³ vaguely identified the compound ZrBe2 and reported that it has a deformed cubic structure. Two patents," , were issued to Mach-lett Laboratories in 1943 and in 1946 regarding the addition of small amounts of zirconium to beryllium in order to improve the ductility of beryllium so that it may better be used for X ray windows. In considering the alloy formation of beryllium with other metals Raynor thought it unlikely that zirconium would have any solid solubility in beryllium. From this indefinite information nothing could be ascertained about the possible use of Zr-Be alloys or the use of these metals intimately. A brief preliminary study of the system Zr-Be by powder metallurgy methods was undertaken to provide regions for more intense studies of Zr-Be alloys and as a guide to a formal phase diagram determination. The investigation described in the following pages was completed in less than three weeks. The usefulness of this rapid method to facilitate phase diagram studies and new alloy investigations will be shown. Materials and Procedure Zirconium powder was produced from crystal bar stock of high purity supplied by Foote Mineral Co. The crystal bar was converted to hydride at 730°C, crushed, and the hydride decomposed in purified argon at 850°C. 60 pct of the powder passed through a 325 mesh screen, 40 pct of the powder was —140 mesh, +325 mesh and the average particle size of the total was 8 to 12 microns. The beryllium powder was used as re-

Jan 1, 1951

United Engineering Trustees, Inc. GEORGE A. EASLEY H. G. MOULTON A. L. QUENEAU The Engineering Foundation GEORGE D. BARRON E. DEGOLYER A. L. QUENEAU Engineering Societies Library Board H. K. MASTERS A. B. PARSONS, Ex-officio F. F. SHARPLESS H. H. SWEETSER ARTHUR L. WALKER

Jan 1, 1934

By Richard O. Carlson

Ions of p31 and B 11 were implanted in natural insulating diamond macles. The thin (-0.4µ) layers showed sheet resistances of 107 to 1011 ohm per sq and activation energies of 0.17 to 0.34 ev above room temperature. However, no Hall effect could be measured, indicating that mobilities were less than I to 10 sq cm per (v-sec). Such low mobilities may be due to excessive scattering due to radiation damage in the bombarded layer or to very high concentrations of active compensating impurities. Annealing did not materially change the room -temperature properties, but the temperature was limited to -800°C by surface graphitization, the latter process probably being accelerated by lattice damage in our diamonds arising from the ion bombardment. A weak n-type thermoelectric power was detected after p31 irradiation, but it cannot be presumed that we have made the phosphorus ions active as donors in diamond. The natural diamonds have a high and uncontrolled concentration of impurities and, when coupled with the radiation damage and graphitization problems, would appear to seriously limit the quality of semiconductor that we can presently achieve by ion implantation in diamond. ALTHOUGH diamonds are usually thought of as insulating in terms of their electrical conductivity, it was found about 15 years ago that natural semiconducting diamonds do occur rarely, and these were designated as type IIb diamonds. These p-type semiconducting diamonds were found to be dominated by an impurity level 0.37 ev from the valence band. Evidence today based on correlation of the concentration of acceptor states from Hall effect measurements with the impurity concentrations determined by neutron activation analysis point to aluminum as the dominant acceptor impurity.' The compensating donor is believed to be nitrogen, which has a donor level 1.6 ev above the valence band.' However, only a small fraction of the total nitrogen content in the diamond is electrically active. An infrared absorption band at 7.8 p and ultraviolet absorption near 4 ev have been associated with nitrogen, the former providing a quantitative measure of nitrogen content.3 The nitrogen content is -l020 cm-3 in insulating or type I diamonds, but is less than 10'' in natural semiconducting diamonds. Much of this nitrogen is distributed in platelets oriented in (100) planes and not atomically dispersed in the diamond lattice.4 Semiconducting diamonds have been deliberately formed by incorporating impurities into the graphite charge in the high-pressure apparatus used to form diamonds.5 These manufactured semiconducting diamonds are always p-type, and while some show the 0.37 ev level due to aluminum, most such samples have been ascribed to impurity banding effects.6 The best natural or manufactured semiconducting diamonds have hole mobilities near 1500 sq cm per (v-sec) at room temperature, and those with the 0.37-ev level can be analyzed to reveal an acceptor concentration of 3 to 8 X 1016 cm-3 and a donor concentration 3 to 10 times lower.' NO bulk n-type diamonds have ever been reported, but the electron mobility has been measured as 1900 sq cm per (v-sec) by irradiating a diamond with ultraviolet to excite electrons out of the deep nitrogen donor level or other levels.7 New hope for the formation of n-type diamond has emerged from the ion-implantation method whereby desired impurities are introduced into a crystal lattice by bombardment with a high-energy beam of the impurity ion. It was found in the case of silicon that the usual donors such as phosphorus and arsenic and acceptors such as boron and gallium could be implanted into silicon. Wentorf and arrow' produced semiconducting layers on diamonds by an ionic bombardment in a glow discharge at potentials of about 2 kv. The observed typeness from thermoelectric probing seemed to depend on the atmosphere gas (nitrogen, argon, or hydrogen) rather than on the electrode material, but the nature of the conduction process in the thin damaged surface layer is completely unknown. A Russian group under Vavilov has attempted high-energy ion implantation in natural diamonds using boron and lithium ions9 and later also phosphorus, aluminum, and carbon ions.10 Their papers claim n-type layers from lithium, phosphorus, and carbon implant and a p-type layer from boron and aluminum implant, though the methods of type determination are not described in detail. Under government contract support, the Ion Physics Corp. has studied ion implantation in several semiconductors. While the bulk of their study1' was devoted to the irradiation of silicon, they did carry out a short study on boron and phosphorus implantation into natural diamonds. They did observe surface conducting layers but did not determine the typeness of the layers. For our experiments, phosphorus and boron were chosen as the dopant ions because of their respective donor and acceptor behavior in germanium and silicon. Moreover, they are the lightest mass dopants of the shallow level donors and acceptors from columns 111 and V of the Periodic Table (excluding nitrogen which is already present in diamond), and will have the largest depth penetration into the diamond lattice. EXPERIMENTAL Diamonds. As the target diamonds for our ion implantation study, we chose commercially available macles, which are flat, twinned diamond crystals. By scanning through the stock of a wholesale distributor

Jan 1, 1970

By H. G. Moulton

The increasing scale of mining operations over the past decade, particularly in connection with the exploitation of large bodies of comparatively low-grade copper ores, has made necessary the study of the behavior of rock under failure. When extractions of as high as 40,000 tons a day are reached in steam-shovel operations and as high as 20,000 tons per day in underground mining operations, it is evident that excavations soon become of such size that the behavior of the rock will often be dependent on fundamental principles applicable to more or less homogeneous materials under stress, rather than on weathering or local planes of weakness. In the ordinary rock excavations encountered in civil-engineering practice, such as excavations for subways, highways, railroads, etc., rock faces are not carried to depths sufficient to develop any pressures, or consequently any failures, except those due to loose masses resulting from local planes of weakness. When, however, orebodies whose tonnage is measured by hundreds of thousands are to be extracted by steam-shovel operations in open pits, it is necessary to determine if possible in advance the slopes that the sides of the pits will assume, for these slopes influence the shape of the excavations and thereby the amount of ore that may be extracted by the open-pit method. When large orebodies are mined underground at depths of 300 to 500 ft. (91 to 152 m.) by caving methods, the surface subsiding as the ore is withdrawn, it is necessary to determine in advance the outermost limits of fracture in the subsiding surface, for on the delineation of these limits depends the location of surface improvements, mills, smelters, etc. and also the location of development work, such as hoisting shafts, main haulage levels, and all other underground openings that must remain undisturbed during the period of ore extraction. Heretofore, in civil-engineering practice, it has been assumed that earth and rock behave differently in failure. For the calculation of earth pressures, formulas are used in which the assumption is made that earth banks fail by sliding along the slope determined by the frictional resistance of the material. The line of failure and the resulting pressure is held to be dependent on the angle of repose, which is different for varying

Jan 1, 1920

By J. F. Peters

The term solution loss is discussed and defined. Examples are given showing that solution loss may either have a favorable or unfavorable effect on blast furnace performance. A theory is advanced explaining the contradictions encountered during earlier studies of the problem. MANY papers have been written and numerous theories advanced concerning the chemical reactions in the iron blast furnace. Richards, discussing the utilization of fuel in the blast furnace, said: "All the carbon burnt in the furnace should be first oxidized at the tuyeres to CO and all the reduction of oxides above the tuyeres should be caused by CO, which thus becomes CO,. This dictum is not Gruner's own words, but expresses their sense, and from the point of view of the present discussion, it is the correct principle upon which to obtain the maximum generation of heat in the furnace from a given weight of fuel." Richards also said the cubic feet of wind per pound of coke does not express how efficiently a furnace is running, but it will be shown later where Howland paid much attention to this figure. Richards pointed out a shortcoming of Grun-er's discussion in that Richards claimed there is not enough CO generated in a good working blast furnace to possibly combine with the oxygen of the ore, so some of it must be reduced by solid carbon. Mathesius2 made two important contributions. First, he wrote the direct and indirect reduction equations showing the heats of formation in each case and stressed that the indirect reduction reaction produces heat while direct reduction absorbs heat. Secondly, he substantiated Richards' conclusion that there may be a deficiency of CO gas and that some direct reduction is required, but he pointed out that "direct reduction in the hearth has often been confused with direct reduction in the stack, which more correctly should be termed 'premature combustion'." Then he said that "as this carbon is consumed partly by economical (direct reduction in the hearth) and partly by wasteful reactions in ever varying proportions, it is evident that the relation of this total carbon gasified above the tuyeres to the fuel consumption of a furnace cannot possibly have a direct bearing on the economy of furnace operation. The premature combustion of carbon (CO2+C?2CO) must therefore in all cases be considered a detrimental reaction." Johnson3 discussed this whole problem. Through experience Johnson found that when departure from Gruner's ideal working is considerable, the fuel economy is poor, and when the quantity of blast goes up, the fuel economy goes up in the same proportion. Johnson said that the wind per pound of coke is a measure of fuel economy, which will be shown to be wrong. Howland4 established the fact from operating data that there was no relationship between the coke consumption of a furnace and the percentage of coke burned at the tuyeres. But some of his calculations have led to questionable conclusions, such as "it is practically impossible to obtain low coke consumption unless we keep our wind low." Howland made an important contribution when, in his concluding paragraphs, he reached certain negative decisions as to why one coke works better than another. He said the reason one coke works better than another in a blast furnace is not because: 1—there is any difference in the percentage gasified at the tuyeres, or 2—there is any difference of wind required per pound of coke. Korevaar5 propounded a new theory on combustion which disagrees with Gruner because "as far as we can see, this is sufficient proof for the invalidity of Gruner's ideal, for if it was valid, the Low coke consumption should always be accompanied by a higher percentage of carbon burned at the tuyeres. This not being the case, we must deliberately give up our belief in Gruner's ideal." The part in italics will be proved to be wrong. Martin" contended that there was not enough reducing capacity in the blast furnace unless solution loss occurs. He came to a series of conclusions, such as: 1—The greatest efficiency of the blast furnace may not be attained when the reduction is performed entirely by carbon monoxide as demanded by Gruner's definition of the ideally perfect working of the blast furnace. 2—The so-called solution loss reactions, which should more properly be termed direct reduction reactions, promote furnace efficiency. 3—In modern blast furnace practice, the carbon consumption of the process is determined primarily by the carbon needed for reduction purposes, any thermal deficiency created by the reduction process being balanced in practice by the use of blast heat. From a practical standpoint further discussion of the theory of chemical reactions is of little moment. There is however one phase of the general theory of chemical reactions which is very important and that is the combustion of coke in the blast furnace. The purpose of this paper is to show that the reaction

Jan 1, 1955

By Zay Jeffries

It has been known for centuries that iron and steel could be hardened by cold hammering and that the metal could be restored to the normal condition by heating to a red heat arid cooling, either rapidly or slowly with nearly pure iron, but slowly with steels containing considerable carbon. The art of tempering steels is also very old. When a medium- or high-carbon steel is quenched from a cherry-red heat, the hardness is increased; this hardness can be reduced by heating to various temperatures below the lower thermal critical point,, which is near 700" C. The present paper will not consider these old and well known changes in iron and steel below the thermal critical range but will confine itself to the more unusual changes, some of which have been studied recently. Stromeyer,1 for example, In 1886, reports that both working steel and heat treatment of steel in the blue-heat range arc highly injurious. Recently, however, some metallurgists believe that the straiglltening of warped steel forgings at a blue heat produces a beneficial effect on the metal2 The Engineering Division of the National Research Council has constituted a committee on Physical Changes in Iron and Steel below the Thermal Critical Range, which has the following personnel: K. R. -Abbott, H. C. Boynton, William Campbell, J. V. Emmons, F. B. Foley, H. J. French, H. M. Howe, Zay Jeffries (chairman), F. C. Langenberg, J. A. Mathews, P. D. Merica, A. H. Miller, J. H. Nelson, G. A. Reinhardt, W. E. Ruder, H. F. Wood. This committee is studying several aspects of the physical changes in iron and steel. The results, reported in the literature and obtained by recent experimentation, will be given; this will be followed by a general theoretical discussion of the more important

Jan 1, 1922

By Zay Jeffries

It has been known for centuries that iron and steel could be hardened by cold hammering and that the metal could be restored to the normal condition by heating to a red heat arid cooling, either rapidly or slowly with nearly pure iron, but slowly with steels containing considerable carbon. The art of tempering steels is also very old. When a medium- or high-carbon steel is quenched from a cherry-red heat, the hardness is increased; this hardness can be reduced by heating to various temperatures below the lower thermal critical point,, which is near 700" C. The present paper will not consider these old and well known changes in iron and steel below the thermal critical range but will confine itself to the more unusual changes, some of which have been studied recently. Stromeyer,1 for example, In 1886, reports that both working steel and heat treatment of steel in the blue-heat range arc highly injurious. Recently, however, some metallurgists believe that the straiglltening of warped steel forgings at a blue heat produces a beneficial effect on the metal2 The Engineering Division of the National Research Council has constituted a committee on Physical Changes in Iron and Steel below the Thermal Critical Range, which has the following personnel: K. R. -Abbott, H. C. Boynton, William Campbell, J. V. Emmons, F. B. Foley, H. J. French, H. M. Howe, Zay Jeffries (chairman), F. C. Langenberg, J. A. Mathews, P. D. Merica, A. H. Miller, J. H. Nelson, G. A. Reinhardt, W. E. Ruder, H. F. Wood. This committee is studying several aspects of the physical changes in iron and steel. The results, reported in the literature and obtained by recent experimentation, will be given; this will be followed by a general theoretical discussion of the more important

Jan 1, 1922

By C. H. Herty

The reactions that occur in the basic open-hearth process are complicated and are subject to many different factors such as temperature, slag composition and rate of boiling of the bath. It is difficult, therefore, to present an extended theoretical discussion of open-hearth operations without confusing the theory of the process with the application of the theory. This paper attempts to present some of the theory of the open-hearth process without mentioning theory at any point, simply giving some of the practical applications of results founded both on theory and practice and on experimental work both in small and large furnaces. It is hoped that an answer to a number of questions commonly asked by the open-hearth operator may be found in this paper. Discussion of the subject matter is taken up more or less in the order in which a heat ie worked, beginning with the oxidation of the scrap charged, sulfur absorption by the scrap, calcination of the limestone, and extending into the pig iron for the charge, the slags formed during the process, and some of the phenomena occurring in deoxidation of the steel and in its action in the molds. Oxidation of Scbap When scrap is charged into a furnace it immediately begins to oxidize, Oxidation is carried out by.three reactions: Fe + H20 + FeO + Hz (absorbs heat) (1) Fe + C02 + FeO + CO (absorbs heat) (2: Fe+ ½O2 + FeO (gives off heat) (3: The product of oxidation contains some Fe3O4, but FeO usually predominates on account of the iron present in close contact with the scale formed For a given type of scrap the amount of oxidation is controlled by thc fuel and by the excess air being carried in the furnace, the temperature 01 the furnace, and the length of time that the scrap is in contact with the furnace gases. In general, less oxidation occurs when the furnace is rur hot so that the scrap melts rapidly. More important in operation thar the two variables atmosphere and temperature, is the type of scrap being

Jan 1, 1929

By E. G. Leonardon, C. Schlumberger, M. Schlumberger

Last year the authors presented a paper that discussed the various electrical measurements they perform in drill holes, which they name "electrical coring."' The object of the present paper is to give a brief account of the points of scientific interest that have been elucidated by further field work and laboratory research, as well as the economic results that have been attained recently. The practical examples given in this paper are drawn, for the most part, from the field work performed in Russian oil fields during the years 1931 and 1932. This is due to the fact that, thanks to the comprehensive cooperation of the Russian geologists and scientists, the authors are allowed to make public a large amount of recant information. In other countries in which the authors are engaged in similar work, the competition between private companies makes it imperative, for a considerable lapse of time, to avoid publication of the results obtained. The following points will be discussed successively, under separate headings: 1. Electrochemical phenomena in drill holes. 2. Stratigraphic correlations and tectonic studies. 3. Relations' between the productivity of oil horizons and their electrical resistivity. 4. Location of coal seams. 5. Summary and conclusions. Electrochemical Phenomena in Drill Holes Technical Publication 462l described the author's discovery concerning the existence of important differences of potential spontaneously gener-

Jan 1, 1934

By Heinrich Ries

Fullers' earth is a clay-like substance, which has the property of decolorizing or clarifying oils. An ultimate chemical analysis shows it to differ from most ordinary clays in having usually a high percentage of combined water and a low amount of alumina. There is probably a large amount of hydrous silica present. Fullers' earth possesses little or no plasticity, and in order to work properly has to be ground very fine. A chemical analysis is of little value at present in determining its quality; only a practical test suffices. Up to about two years ago all of the fullers' earth used in this country was imported from England; but about that time deposits were discovered in Florida, "† and since then rumors of its occurrence have been coming from all parts of the country. Next to the Florida deposits of fullers' earth, those of South Dakota are the most extensive thus far discovered in this country. The earth was first discovered near Fairburn, Custer county, and other deposits have since been prospected at Argyle, Minnekahta and other localities. Fairburn.—One of the first deposits located and opened up is five miles southeast of Fairburn, Custer county. The mine is a mile from the Fremont, Elkhorn and Missouri Valley Railroad, and the section exposed shows, beginning at the top: Feet. Micaceous sandy clay,......... 6 Fullers' earth,..........9 Micaceous sandstone,......... The fullers' earth passes upwards into the sandy clay, but in its purer portions it is a yellowish, gritty clay, with a somewhat

Jan 1, 1898

By R. C. Temps, G. E. Aiken

Compania de Acero del Pacifico, S.A., the sole Chilean steel producer, is adding to the expanding Chilean economy with development of the El Algarrobo mine. Expected to go on stream early in 1962, Algarrobo is a conventional open pit mine that will include facilities for ore extraction, crushing and screening, rail transport to the harbor at Huasco, modern ship-loading equipment and maintenance shops. CAP anticipates producing 1.38 mil- lion tons annually of high-grade ore for national and world market consumption. Chilean and North American management and engineering teams combined more than a decade ago in the financing and building of CAP'S Huachipato integrated steel plant. A similar performance is being achieved in northern Chile near the town of Vallenar with the opening of a 50-year supply of iron ore from the Algarrobo deposit. This successful intra-American undertaking deserves special mention in these times when some U.S. foreign assistance programs must be defended, particularly with respect to Latin America. North American financial participation in Algarrobo, through the Export-Import Bank of Washington, represents the greatest portion of the $24 million being invested.

Jan 3, 1962

By Thomas S. Lovering

Hot springs, geysers, steam-emanating fumaroles- these creatures of nature were until recently little more than geological curiosities, but today they are exciting the interest of engineers around the world for it has been shown that such hyperthermal areas can be profitably harnessed by man to provide heat and power for his communities. Although water from hot springs was used centuries ago to heat some Korean dwellings, is being used today by one-third of Iceland's population for similar purposes, and is finding industrial applications in New Zealand and elsewhere, the most dramatic use of geothermal energy has been its conversion into electricity. The largest installation at the present time is that at Larderello, Italy, where the Count of Larderello began to experiment in the production of electricity from geothermal steam in 1904. Eight years later after a quarrel with the local power company, the Count installed his first steam turbine, a unit of 250 kw capacity.

Jan 9, 1965

The Ortiz Mountain property is located approximately 40 km (25 miles) southeast of Santa Fe and 13 km (8 miles) from the village of Cerrillos. The property embodies a Spanish mineral grant from which Gold Fields acquired about 2, 200 hectares (900 acres of surface and mineral rights. Following a period of exploration, metallurgical testing and development of a feasibility study in 1974, the decision was made, because of the higher gold price in the fall of 1978, to place the property into production. the gold is confined in a quartzite breccia; it is an unusual occurrence because the gold in this host rock is leachable at minus 19 mm (3/4 in. ). Total ore reserves are estimated at approximately 3.6 million mt (4 million st) averaging 1.89 g per mt (0.055 oz per st) based on a cut-off of 0.7 g (0.02 oz). The ore will be recovered by open pit mining at a stripping ratio of 1. 2:l. Production is scheduled for 13,600 mt (15,000 st) of ore per week or approximately 680,000 mt (750,000 st) per year. Primary crushing of pit-run material is by a 1,070 by 1,015 mm (42 in. by 40 in.) jaw crusher. Crushed ore is conveyed to stockpile and then to a 2.13 m (7 ft) standard crusher with the screened over- size crushed in a 1.5 m (5 ft) tertiary cone crusher. The screen undersize, the final product for leaching, is minus 19 mm (3/4 in. ). A 1, 360 kg (3,000 lb) sample is cut from the crushed ore stream, further crushed in a small jaw crusher and then sampled in two more stages by Vezin samplers to produce a final 13.6 kg (30 lb) sample for assaying. Pebble lime is then added to the ore on the belt as it is sent to the conveyor gantry spanning the leach pads. A tripper on this moving gantry stacks the leach ore without compaction. The entire crushing plant and conveying system is of open-air construction. Leach pads have a total length of 515 m by 60 m (1,700 ft by 200 ft) wide with usable dimensions of 490 m by 58 m (1,600 ft by 190 ft). The directional length slope is 3. 870 with 370 on the width. The pad is constructed of 175 mm (7 in. ) thick asphalt containing a rubberized asphalt membrane. It is divided by a 300 mm (1 ft) high curb into eight segments. Each segment is loaded with 13,600 mt (15,000 st) of ore, which is one week's production. Optimum working height of a pad is considered to be 3. 0 m (10 ft) with a maximum height of 4. 0 m (14 ft).

Jan 1, 1981

By Victor O. Homerberg, Dexter N. Shaw

A study of the correlation of the mechanical properties and of the microstructure with the heat treatment of 60-40 brass has been confined, heretofore, to the rolled or extruded material as received from the mannfacturer. The results obtained by Babson and Buhler,' Bengough and Hudson12 Stead and Stedman,3 and Brayton4 have been confined to the treatment of the material as received. No attempt was made to get the material into a given condition and then to work from this basis. To start with a given structure would have the decided advantage of making the work independent of the original condition, hence, to make the results reproduceable. In a previous paper, it was shown, in connection with the study of the transformation that occurs at about 470" C., that if specimens were quenched to produce the beta structure and then reheated, the beta would begin to break down, at approximately 200" C., into a very finely divided alpha. It was predicted that important results might be obtained if test pieces were to be given a similar double heat treatment and then tested for the mechanical properties as well as a study of the microstructure. The material used in the present investigation was a 3/4-in. round bar of extruded muntz metal of the following composition: Copper, 61.05 per cent.; zinc (by difference), 38.90 per cent.; lead, 0.05 per cent.; iron, trace; tin, nil.

Jan 1, 1924

By Robert S. Moehlman

Is recent years, exploration and development by diamond drilling has become a popular attack on the problem of finding new ore shoots and developing extensions of known shoots. Diamond drilling has been used in recent years in extensive sampling of disseminated copper deposits, in preference to churn drilling. At the Harvard gold mine, near Jamestown, California, Philip R. Bradley, Jr., general superintendent, reports that: "The Harvard work was a singular example of the reliance that can be placed on diamond drilling in evaluating an ore body." Drilling at the Harvard mine will be discussed in a subsequent section of the paper. So popular has diamond drilling become, indeed, that many who have had slight experience with drilling are inclined to regard it as a cheap cure-all. This paper proposes to show some of the limitations on the application of drilling and some of the steps that should be followed in drilling programs to obtain reliable results. Cost oF Drilling Drilling has the advantage, over shaft sinking and drifting, of lower cost and greater speed. As compared with churn drilling, the advantage of bringing up a coherent sample instead of fine cuttings for a sample is obvious. Diamond drilling is generally more expensive, however, and more engineering effort is required in combining the average of core and sludge samples. Exploration of drift walls by hammer drills to a depth of less than 30 ft. is generally cheaper than diamond drilling, but beyond this depth the diamond drill is cheaper and more efficient. The principal factor in determining cost of drilling is the character of the ground drilled. Broken ground with many fissures is most expensive to drill. Hard ground is less of a problem with diamond drills than with ordinary machine drills. Hardness or softness affects only the speed of drilling. Caving, easily washed, sandy or clayey ground requires continual cementing and casing, which is the greatest cost problem. Thus, soft, incompetent ground is more costly to drill than hard, massive ground. Cost of drilling per foot in good to fair ground varies from less than $I per foot, achieved in some districts in Ontario, the Mother Lode, and Missouri, to $5 per foot in many western states. In bad drilling ground, costs may range from $5 to $15 or more per foot, thus approaching the cost of drifting. Other factors that increase the cost per foot are: I. Short total length of hole drilled, so that the cost of moving in crews and equipment must be spread over a relatively few feet. 2. Cost of drilling per foot increases with depth beyond about 500 ft.. as more time is consumed in pulling rods' 3. Cost of preparing drilling stations, getting air underground to stations? etc' 4. Inaccessibility and lack of water on the job make for higher costs.

Jan 1, 1946

By H. Hubert

The first attempts at direct utilization of blast-furnace gas in engines were made in 1895. For a considerable time the gas had been burnt in Cowper stoves for heating the blast for the furnace, and under the boilers which supplied steam to the blowing-engines, and others serving the furnaces. It was natural, therefore, that the idea of directly employing it in gas-engines should have occurred simultaneously to several engineers, notably to Lurmann and to Lencauchez, who had pointed out the blast-furnace as a powerful gas-producer. Nevertheless, nowhere had any attempt been made to apply it to this purpose up to the end of 1894, when Thwaite proposed it to Mr. James Riley, of the Glasgom Iron & Steel Company. About the same time investigations were being made in Belgium and in Germany, independently of Thwaite's experiments, which were not generally known on the Continent. The industrial world, which up to that time had hardly favored the idea, had thus been gradually prepared to receive it. The gas-engine, long restricted to small sizes and dependent upon the use of an expensive fuel obtainable only in large centers, now began to make headway. At the Paris Exhibition of 1889 two engines of 100 h.p. were shown and excited much interest among engineers. One had four cylinders, and was made at the celebrated works of the Deutz Company, and the other was a single-cylinder engine, exhibited by two French designers, Messrs. Delamare-Deboutteville and Malandin. In the meanwhile the design of gas-producers had made important progress, completely freeing the new engine from its

Jan 1, 1907