Search Documents

By Harold Markus, Gerhard Derge

THE first paper1 of this series described a technique of careful surface preparation by means of which reproducible results may be obtained from potential measurements of the behavior of tin in carbonate solutions with a pH range from 8.4 to 11.2. It then went on to establish the behavior of pure tin electrodes under these conditions and showed that the metal remains active at all times, though the steady potential attained after several hours decreases from I.I2[t] volts at a pH of 12.6 to 0.6 volts at a pH of 8.4. This behavior may serve as a norm with which all other data can be compared. In the second paper,2 small amounts of other anions were added to the carbonate solutions and the conclusion was reached that the common impurities encountered in alkaline materials packaged in tin do not increase corrosion. In fact, in some cases these anions may actually promote the formation of protective films. The present paper rounds out this survey by presenting data on the influence of cations added to the carbonate solutions, as well as the effect of alloy additions to the tin. In many cases the potential data are supplemented with weight-loss measurements. Information is also presented on the effects of some additional anions, the influence of gases above the electrolyte, the behavior of high-purity tin, and the effect of atmospheric oxidation on the corrosion resistance of the above-named alloys. Analysis of the entire body of data discloses some general rules applicable to corrosion in carbonate solutions. The experimental methods used are the same as those previously described. EXPERIMENTAL DATA Cations.-The carbonates of the cations K+, Li+, NH4+, which are soluble, were studied in the same way as the anions, by adding 0.01 mol of the metal carbonate to one liter of 0.2 M sodium carbonate solution, pH 11.2, or to 0.1 M sodium bicarbonate, pH 8.4. The other metallic carbonates are only slightly soluble, of the order of 0 7-3 mols per liter or less, and the sodium carbonate solutions were saturated by adding excess reagent several days before the experiment, shaking frequently, and filtering just before use. The chemicals were c.p. grade in each case except the indium salt. This salt was prepared by solution of the metal in hydrochloric acid and precipitation by addition of Na2CO3. These cations may be divided into two classes, according to their effect on the potential behavior of the tin: (I) normal, (2) passive. To offer a basis of comparison, curves I of Figs. I and 2 are given to illustrate the behavior of tin in carbonate solutions saturated with CaCO3. These curves are the

Jan 1, 1941

Meeting of Mar. 27, 1914.-President Thayer announced the appointment of H. S. Munroe as a member and E. Gybbon Spilsbury as Chairman of the Library Committee of the Institute. The President announced the appointment of the Committee on Papers and Publications, the Technical Committees, the Committee on Increase of Membership, and the Committee on Junior Members and Affiliated Student Societies. The President announced the appointment of Dr. George F. Kunz as a member of the Reception Committee of the International Engineering Congress, 1915. It was voted that the Institute accept the invitation of the Mining and Scientific Press to occupy space at the Panama-Pacific Exposition next to them and avail itself of the service of their representative to receive and register members of the Institute who visit this space during the exposition.

Jan 5, 1914

By E. R. Borcherdt

IT is notable that the first large-scale mine operation equipped entirely with detachable bits was the Badger State mine of the Anaconda Copper Mining Co. in Butte, Montana, just 30 years ago. This mine in 1922 was producing approximately 1200 tons of ore per day. Much of the data presented in C. L. Berrien's article1 describing the development and installation of the Hawkesworth detachable drill bit were obtained from these operations. As in any pioneering effort, no precedent existed and many difficult problems required solution, so that the changeover to detachable bits at all Butte hill mines was not completed for 6 years. There was widespread disbelief as to the probable efficiency of the new installation.

Jan 2, 1953

By G. W. Imholz

A number of interesting wells were drilled in north central Texas during 1940. The Shell Oil Company's Smith well in scc. 143, block I, H. and T. C. survey, Stonewall County, was completed for an initial production of 581 bbl. per day from the Mississippian limestone, with a total depth of 6065 ft. The same company's Patterson well, sec. 393, block D. H. and T. C. survey, Stonewall County, tested the Ellenburger limestone and was abandoned as a dry hole with a total depth of 6760 feet. In Nolan County the Tex-Harvey Oil Co. drilled a well in sec. 43, near the Tipton well, which was completed as a small producer in the Strawn section. The Tex-Harvey well tested this producing horizon but was abandoned as a dry hole with a total depth of 5210 feet. The Montour-Haggart well, sec. 184, block 2, H. and T. C. survey, Fisher County, tested the Strawn and was abandoned with a total depth of 5664 feet. The Georgian Oil Company's Blach, sec. 309, T. R. and L.. Shackelford County, encountered the top of the Ellenburger limestone at 4725 ft. After being plugged back to 3915 It. from a total depth of 4825 ft., the well tested 10 bbl, of oil per day and 300 bbl. of water. The W. I. Sothern No. 2 Carlisle well in sec. 293 was deepened to the Cambrian. The top of the Ellenburger was encountered at 6540 fcet. A wildcat well in Fisher County, the E. A. Stephenson-Maberry, apparently opened a new pool when the well encountered sand from 3298 lo 3302 ft. and was completed for 50 bbl. per day in the Cook sand horizon. In Jones County, the King Oil Company's Olsen well, sec. 158, B. B. B. and C. survey, extended the Avoca-Olander pool. The well was completed for 263 bbl. in 8 1/2 hr. from the Palo Pinto limestone, from 3298 to 3302 ft. Ungren-Frazier extended the Akard pool with No. I Akard, in the D. 'T. Bruce survey. The well was completed for 83 bbl. per day from the Cook sand, encountered from 2109 to 2126 feet.

Jan 1, 1941

By G. W. Imholz

A number of interesting wells were drilled in north central Texas during 1940. The Shell Oil Company's Smith well in scc. 143, block I, H. and T. C. survey, Stonewall County, was completed for an initial production of 581 bbl. per day from the Mississippian limestone, with a total depth of 6065 ft. The same company's Patterson well, sec. 393, block D. H. and T. C. survey, Stonewall County, tested the Ellenburger limestone and was abandoned as a dry hole with a total depth of 6760 feet. In Nolan County the Tex-Harvey Oil Co. drilled a well in sec. 43, near the Tipton well, which was completed as a small producer in the Strawn section. The Tex-Harvey well tested this producing horizon but was abandoned as a dry hole with a total depth of 5210 feet. The Montour-Haggart well, sec. 184, block 2, H. and T. C. survey, Fisher County, tested the Strawn and was abandoned with a total depth of 5664 feet. The Georgian Oil Company's Blach, sec. 309, T. R. and L.. Shackelford County, encountered the top of the Ellenburger limestone at 4725 ft. After being plugged back to 3915 It. from a total depth of 4825 ft., the well tested 10 bbl, of oil per day and 300 bbl. of water. The W. I. Sothern No. 2 Carlisle well in sec. 293 was deepened to the Cambrian. The top of the Ellenburger was encountered at 6540 fcet. A wildcat well in Fisher County, the E. A. Stephenson-Maberry, apparently opened a new pool when the well encountered sand from 3298 lo 3302 ft. and was completed for 50 bbl. per day in the Cook sand horizon. In Jones County, the King Oil Company's Olsen well, sec. 158, B. B. B. and C. survey, extended the Avoca-Olander pool. The well was completed for 263 bbl. in 8 1/2 hr. from the Palo Pinto limestone, from 3298 to 3302 ft. Ungren-Frazier extended the Akard pool with No. I Akard, in the D. 'T. Bruce survey. The well was completed for 83 bbl. per day from the Cook sand, encountered from 2109 to 2126 feet.

Jan 1, 1941

Papers published by the Institute are issued in a variety of forms MINING TECHNOLOGY, issued every other month, contains the TECHNICAL PUBLICATIONS on Metal Mining, Minerals Beneficiation (milling and concentration), Industrial Minerals (nonmetallic) and Mining Geology, Mining Administration, and Geophysics papers relating to Metal Mining (A, B, H, I, K, L ) METALS TECHNOLOGY, issued eight times a year, contains the TECHNICAL PUBLICATIONS of the Iron and Steel Division and the Institute of Metals Division, and once or twice during the year those on Non-ferrous Metallurgy (reduction and refining of nonferrous metals) (C, E, and D ) PETROLEUM TECHNOLOGY, issued every other month, contains the TECHNICAL PUBLICATIONS of the Petroleum Division, together with Geophysics papers relating to -the finding of Petroleum (G, L ) COAL TECHNOLOGY, issued four times a year, contains the TECHNICAL PUBLICATIONS of the Coal Division (F ) MINERAL INDUSTRY EDUCATION DIVISION papers appear in a TECHNOLOGY according to classification of subject matter DISCUSSIONS appear in the respective TECHNOLOGY as available MINING AND METALLURGY is the monthly magazine, which contains papers of general interest and news of the membership

Jan 1, 1952

Institute of Metals Division Iron and Steel Division Extractive Metallurgy Division Council J H Scaff (IMD) Chairman, Robert W Shearman, Secretary, J S Smart, (IMD), P T Stroup, (EMD), A W Schlechten, (EMD), J S Marsh, (ISD), A W Thornton, (ISD), M E Violin, (MED), D S Eppelsheimer, (MIED) Journal of Metals Editorial Advisory Committee J S Smart, Jr, Chairman, W A Dean, J C Kinnear, Jr, T D Jones, Evan Just, John Marsh, M Tenenbaum Pacific Northwest Regional Conference A Y Bethune, General Chairman, Frank N Marr, Chairman, General Arrangements, R J Lapee, Chairman, C P Love, (EMD Program), W M Armstrong, Chairman, Physical Metallurgy Program, L W Heinzinger, Chairman (ISD Program), J P Spielman, Chairman, (MIED Program) New England Regional Conference K H Mairs, Chairman, W A Backofen, Vice-Chair¬man, Delmar E Trout, Secretary, G W Coleman, Treasurer, F H Wilson, Past Chairman, Members at Large Sidney Siegel, Boston, G F Donahue, Connecti¬cut Representatives from Connecticut Frank Chudy, J E Chafey Representa¬tives from Boston N L Reed, E Gordon

Jan 1, 1955

Speech advocating a new law of the sea-the "common heritage of mankind." The 3rd Law of the Sea (L0S) Conference was held in Caracas in mid-1974, and a fourth UN conference, scheduled for mid-March in Geneva, will once again attempt to produce a cohesive LOS Convention to take up where the 1958 Geneva Convention left off. The 1958 Convention specified coastal state resource rights on a continental shelf out to a water depth of 200 m-a supposed technological limitation at the time. But the surge of offshore petroleum drilling and the advent of the nodule resource have long since exploded beyond the 200-m limit.

Jan 4, 1975

By Charles H. Morgan

Jan 1, 1905

Arizona ROBERT E TALLY, Chairman CARL F MILLS, Secretary-treasurer, P O Box 1462, Jerome, Ariz W. S. BOYD THOMAS H O. O'BRIEN F. W MACLENNAN Boston Meets first Monday each winter month GALEN H. CLEVENCER, Chairman HOLCOMB J BROWN, Vice-chairman F LEROY FOSTER, Secretary-treasurer, Room 8-219, Mass. Inst of Tech, Cambridge, Mass A. E WELLS H A WENTWORTH

Jan 1, 1923

EXECUTIVE COMMITTEE OF THE BOARD OF DIRECTORS W E WRATHER, Chairman A B KINZEL -EARLE E SCHUMACHER DONALD H MCLAUGHLIN - JOHN R SUMAN FINANCE COMMITTEE OF THE BOARD OF DIRECTORS ERLE V DAVELER, Chairman PHILIP KRAFT - CLYDE E WEED

Jan 1, 1952

By ROY BERENTZ

MANUFACTURE is the transformation of material by the application of energy and power. The energy of a man exerted throughout a day is equivalent to about one horsepower-hour of mechanical work an amount which can be purchased for less than 2c. It is evident that manual labor is uneconomical if mechanical energy can be applied effectively, or without disproportionate expense. Since manual energy is relatively so costly, economy demands that mechanical power be employed so as to reduce the human effort connected with mining operations to a minimum. Power, like other commodities, is most efficiently produced in large quantities. Mechanical transmission, once prevailing, is being rapidly superseded by electric drive. There are many reasons for this change; such as increased production, ease and accuracy of control, convenient application, ease of moving, etc.

Jan 1, 1930

By J. E. Tobey, David R. Mitchell, J. H. Kerrick

DETAILED knowledge of purchase specifications established by coal consumers is essential to the successful design and operation of a coal-preparation plant. ANTHRACITE Specifications should be considered by both the consumer and the producer as guide posts outlining a certain path for both to follow. Plants differ, therefore specifications must differ to meet the varied requirements. Specifications are not of themselves a "cure all" or an assurance of complete satisfaction in fuel utilization. Specifications should not be regarded as a license to engage in an orgy of buying any and all coals that may happen to fall within their limits. This would lead to the indiscriminate mixing of coals which may vary in their burning characteristics. Different coals of equal grade tend to be individualistic in their burning characteristics. Rather, specifications should be used to help simplify coal selection, to reduce the actual number of coals used over a given period; in other words, to have a stabilizing influence on coal or customer turnover. In the final analysis, the use of too many coals per year in a plant is costly to both the consumer and the producer. Too many sources usually result in higher operating and maintenance costs for the consumer and higher sales costs for the producer. Finally, the statement included in the report accompanying the com¬prehensive Coal Selection Charts prepared by the Coal Committee of the National Association of Purchasing Agents, and released in 1938, is significant. This Committee worked diligently for a period of 15 years seeking to find a scientific and reliable method for selecting coals. The two following paragraphs are quoted from its report: More important is the fact that no ready-made classification or set of specifications can possibly replace the judgment and resourcefulness of an experienced combustion engineer or fuel technologist, nor the usual need for full scale plant tests under the exact conditions of use before a final decision is made ...

Jan 1, 1943

By W. B. Mather

Arkansas' nonmetalliferous deposits are of many different types. The principal types briefly described in this paper are: clays, shales and slates; silica deposits; limestone and dolomite; barite; gypsum; celestite; nepheline syenite; greensand; phosphate; vermiculite; fuller's earth; bentonite; diamonds; sand and gravel. The future development of these deposits is expected to effect profoundly the industrial development of the state.

Jan 5, 1950

By William Marsh Baldwin

TWO of the most useful and important equations available to the metallurgist for the study of plastic deformation of metals are the Huber-von Mises-Henckyl-~ and the St. Venant7-10 equations. Huber-von Mises-Hengky Equation The Huber-von Mises-Hencky equation answers the question: When does plastic flow occur in metal that is subjected to a multi-axial stress? It occurs, according to this equation, when the three principal stresses,t UI, u2, and u3 satisfy the equation: (<ri - <r2)2 + (<r2 - <rsY + (ff! - <r3)* = 2Ki [i] Here K is the yield strength of the material as determined in an ordinary tensile test. If the quantities ul, 52, andas are assigned to the coordinates of a Cartesian three-dimensional system, this expression describes a cylinder whose axis of symmetry is inclined at equal angles to the three coordinate axes4s6 (Fig. I). The radius of this cylinder is .\/%K. For the purpose of simplicity, it is sometimes advantageous to ascribe the values al/K = sl, az/K = s2, UD/K = SJ to the three coordinate axes instead of the principal stress alone. In this case, Eq. I becomes (*i - s*)1 + (s2 - S3)2 + (si - SiY = 2 [2] and the radius of the cylinder becomes \/%. In the latter method of representation, a point lying inside the cylinder indicates that the metal will react elasti-cally, whereas a point lying on the cylindrical surface indicates that the metal will behave plastically. Some of the geometric features of this cylinder are worthy of study. Let us inquire first as to what interpretation may be placed upon what we will choose to call the "circles of latitude" of the cylinder (L in Fig. I) and the "meridians" of the cylinder (M in Fig. I). Circles of Latitude Circles of latitude are formed by allowing a plane, passing perpendicular to the cylinder axis, to intersect with the cylinder. Any point, P, on this circle is presumed to have the coordinates sl, SZ, and s3. The coordinates of the point resulting from the intersection of the plane and the cylinder axis will be a, a, and a (since the cylinder axis is equally inclined to the three coordinate axes). L?t US now pass a line through the point on the circle and the point on the axis.

Jan 1, 1946

By William Marsh Baldwin

TWO of the most useful and important equations available to the metallurgist for the study of plastic deformation of metals are the Huber-von Mises-Henckyl-~ and the St. Venant7-10 equations. Huber-von Mises-Hengky Equation The Huber-von Mises-Hencky equation answers the question: When does plastic flow occur in metal that is subjected to a multi-axial stress? It occurs, according to this equation, when the three principal stresses,t UI, u2, and u3 satisfy the equation: (<ri - <r2)2 + (<r2 - <rsY + (ff! - <r3)* = 2Ki [i] Here K is the yield strength of the material as determined in an ordinary tensile test. If the quantities ul, 52, andas are assigned to the coordinates of a Cartesian three-dimensional system, this expression describes a cylinder whose axis of symmetry is inclined at equal angles to the three coordinate axes4s6 (Fig. I). The radius of this cylinder is .\/%K. For the purpose of simplicity, it is sometimes advantageous to ascribe the values al/K = sl, az/K = s2, UD/K = SJ to the three coordinate axes instead of the principal stress alone. In this case, Eq. I becomes (*i - s*)1 + (s2 - S3)2 + (si - SiY = 2 [2] and the radius of the cylinder becomes \/%. In the latter method of representation, a point lying inside the cylinder indicates that the metal will react elasti-cally, whereas a point lying on the cylindrical surface indicates that the metal will behave plastically. Some of the geometric features of this cylinder are worthy of study. Let us inquire first as to what interpretation may be placed upon what we will choose to call the "circles of latitude" of the cylinder (L in Fig. I) and the "meridians" of the cylinder (M in Fig. I). Circles of Latitude Circles of latitude are formed by allowing a plane, passing perpendicular to the cylinder axis, to intersect with the cylinder. Any point, P, on this circle is presumed to have the coordinates sl, SZ, and s3. The coordinates of the point resulting from the intersection of the plane and the cylinder axis will be a, a, and a (since the cylinder axis is equally inclined to the three coordinate axes). L?t US now pass a line through the point on the circle and the point on the axis.

Jan 1, 1946

Jan 1, 1935

By W. A. Tiller, W. C. Johnston

A high-temperature electromagnetic stirrer is described in which heating and stirring are accomplished by independently controlled power sources. The appavatus is suitable lor use at temperatures up to 1700°C in a variety of ambient atmospheres. Some typical examples of the homogenizatimz capabilities of the system are given. THERE are few processes in solidification that are not markedly affected by motion in the melt during freezing. In many instances, the mechanisms are diffusion-controlled, and the transport in the melt may be greatly accelerated by deliberately stirring the melt. In zone-refining, stirring1 assists the removal of rejected impurities from the interface, so the process proceeds at a faster rate. The transition from a planar to a cellular interface is caused by constitutional undercooling in the melt ahead of the interface: and stirring delays its onset. Stirring is valuable for homogenization of melts: and chemical reaction with sluggish kinetics may be accelerated. Finally, it has been observed that grain refinement is related to motion in the melt. Fine grain castings are usually produced by the addition of catalysts to the -melt,&apos; catalysts which are thought to act simply as hetereogeneous nucleation centers. Even here motion is important. Richards and Rostoker 5 applied ultrasonic vibration to a solidifying A1-Cu alloy which had been innoculated with a catalyst and found that the grain diameter fell linearly with the amplitude, the peak acceleration and the power input to the melt from the transducer. Finally, mechanical and electrical stirring alone have been used to generate a fine-grained structure.6,7 Johnston ef a1.&apos; have carried out a series of systematic investigations of grain refinement by electromagnetic stirring in a number of low melting point alloys. They found, for example, that the number of grains per unit volume in Pb-Sn alloys could be increased several orders of magnitude by stirring an undercooled melt at the moment of recalescence. In general, a relation AT .H = constant prevailed for a given grain size, where AT was the undercooling of the melt and H the field strength. In more recent work, deliberate homogeneous nucleation of slightly undercooled melts established that the mechanism of refinement must be one involving crystal fragmentation and subsequent multiplication, rather than a "shower" of nuclei effect.9 It is the purpose of this note to describe a stirring device suitable for use up to 1700°C. At low temperatures mechanical stirring and direct-current methods are feasible, but at high temperatures the problem of a protective atmosphere and of electrode corrosion rules out such procedures. The most convenient method for high temperatures is to use externally generated ac fields for both stirring and heating. With rf induction heating alone, considerable stirring and agitation can be achieved, but in general the penetration of field into the melt is small, and the stirring cannot be controlled independently of the heating. In the present experiments, separate power sources of different frequencies for heating and for stirring were used. A susceptor design was chosen so that the 450 kc rf heating field was completely absorbed in the susceptor. The stirring frequency, 400 cps, hereafter called the af field, was chosen so that a high penetration of the melt proper was achieved. EXPERIMENTAL APPARATUS The apparatus, Fig. 1, consists of a quartz tube and end plates, surrounded by an rf induction coil and six equally spaced af stirring coils, four of which are shown in full and a fifth in section. Each af stirring coil is a transformer of which the secondary is a single-turn water-cooled copper loop and the primary is composed of two 10 amp-117 v Variac cores as shown. These cores are cooled by forced air, as each of the six pairs will carry maximum currents of 15 amp for short periods. Each set of Variac windings are connected in series, but opposite sets are connected in parallel with a three-phase 400 cps 400-v source. By properly phasing the coils in this way, a rotating field is produced. Capacitors C1, C2, and C3 in Fig. 2 are used to match this inductive load to the generator. Fig. 3 shows a cutaway view of the quartz tube. The sample (1 in. diam by 1 in. high) is placed in a tapered alumina crucible. An axial W-26 pct Re thermocouple, enclosed by a protection tube, is provided. The cruci-

Jan 1, 1968

By Courtenay de Kalb

REVISION of the United States mining law is needed. chiefly because of the following reasons: 1. The conceptions as to the characteristics of orebodies that were held at the time the statute of 1872 was enacted have since proved to be in many respects erroneous. 2. The operation of the existing law has been found to work unnecessary hardship upon many claimants to mineral land. 3. The existing statute fails in large degree to encourage development of mineral resources. 4. The existing law often produces conflict between placer and lode-claim rights, working unnecessary injustice to placer claimants. 5. The methods of establishing the rights of locators on United States mineral land are defective, and are not uniform throughout the States within which such lands exist. LAW OF THE APEX The objections to the so-called "law of the apex" are so well known as to require no detailed statement. It is sufficient to point out that the apex rule was based upon the notion that ore deposits consisted of well-formed veins included between definite walls, like the slice of ham in a sandwich. The fact is that veins conforming to that simple type are rare. Irregularity is the rule, and the chief metal production of the United States comes from masses which bear no resemblance to the tabular form of vein. Manifestly the law of the apex fails completely in such cases. Moreover, the tendency is constantly toward the exploitation of ores of lower grade than could formerly be worked, and such deposits exist mainly in the form of large irregular impregnated zones and masses, so that the future. development of our mineral resources would be continuously embarrassed by shadowy claims to extra-lateral rights by the locators of so-called apexes

Jan 2, 1915

By Chester T. Sims

RECENTLY, a new type of superalloy material called TD Nickel* has been marketed.&apos; It is a sim- ple, two-phased alloy, consisting of thoria particles dispersed in nickel of rather high purity (Ni-2 pct Thoz). Its mechanical properties appear relatively superior to previous experimental material attempting to use the oxide nonmetallic dispersion concept (except SAP), and superior to conventional nickel-base alloys at high homologous temperatures. This is derived from an interesting method of creating the dispersion, arising during chemical processing of the nickel and thorium salts in solution while reducing the nickel to metal. An evaluation of the thoria phase was conducted at this laboratory. Material and Procedure. TD Nickel was made available, consisting of several inches of 0.470-in. rod, extruded at a ratio of 64: 1, straightened, and centerless ground. Property determinations on this rod by the supplier at 1800°F showed an ultimate tensile strength of 11,400 psi, yield strength of 9600 psi, and 6 pct elongation. Specimens were removed from the rod for as-extruded metallography, and two 1/2-in. lengths supported on high-purity Al2O9 bricks were placed in a laboratory muffle furnace for exposure at 2000° F. The furnace door was left cracked to allow a slight amount of circulation. One specimen was removed at 200 hr for examination; the other was left for 2000 hr. Metallography. The micro structures obtained for the three conditions of exposure are shown in Fig. 1. Elongation of the grain structure in the extrusion direction is readily evident. The grains appear to be up to 0.001 in. (0.003 cm) long, with a length/width ratio of about 10: 1. Allowing for modest local in-homogeneities in structure, no significant change in thoria particle size or nickel alloy grain size occurred during the 2000°F exposure. However, etching depth varies slightly from one specimen to another, changing the number of particles visible. The thoria dispersion appears to be in the order of 0.01 (min) to 0.5 (max) p diam. The minimum diameter is difficult to estimate at X10,000, and may be less. Interparticle spacing appears to be about 0.1 p. Etching effects can be seen, depending upon grain orientation. A cubic etch-pit pattern appears in certain grains, apparently when etching is started by an anodic particle of thoria, Fig. l(c). The cubic pattern appears related to crystallographic orientation, and is prominent when the [ l00 ] direction is perpendicular to the plane of polish. The grains which present a ridged appearance in the photograph appear to be oriented with the [110} direction perpendicular to the plane of polish. Analysis. The thoria particle size was measured by a line intercept method perpendicular to the extrusion direction. Only particle sizes measuring 0.001 in. at X10,000 or larger could be extimated. Within limits of experimental error, particle size distribution appears to be unaffected by exposure, Fig. 2. To check structural stability further, a grain-growth evaluation was made. The number of grain-boundary intersections was counted at X500 on each of several traces normal to the extrusion direction for each condition. It can be seen from Table I that grain diameter appears unchanged by the 2000°F exposure. The slightly finer grain diameter after 200 hr may be attributed to variations in grain size from area to area in the original extrusion. From the present rather limited study of Ni-2 Th on, it appears that: 1) for time-temperature exposure up to 2000 hr at 2000°F (Larsen-Miller parameter = 57, homologous temperature = 0.8) thoria particles of the size studied are highly thermally stable; they do not significantly react, agglomerate, or diffuse; and

Jan 1, 1963