Search Documents

By Frank Woolley, John F. Elliott

The high-temperatzrre solulion calorimeter has been modified and an extension dynamic analysis of i/s transient behavior has provided an improved basis for interpretation of the experimental data. The partial molar heats of mixing, Him, of aluminum, copper, and silicon in the corresponding binary liquid-iron alloys haz,e been measured directly at 1600°C. The resulls in kcal per g-alom are: THE high-temperature1,2 solution calorimeter was planned and designed to obtain directly the partial molar heat of solution of solute elements in a variety of liquid metals that might serve as solvents. Results obtained in the temperature range of 1000° to 1200°C were described in the two earlier publications. However, a long-term goal in the program has been to obtain measurements at 1600°C of the heats of solution of elements in liquid iron. Hence, subsequent to the work last reported,2 and based on the experience of the first two studies, the calorimeter system has been modified and operated at 1600°C to obtain measurements on the Fe-Si, Fe-A1, and Fe-Cu systems. This paper reports the results of the work. THE MODIFIED SYSTEM It was clear from the earlier results that the most precise measurements can be obtained with the high-temperature solution calorimeter when the solution time is less than approximately 30 sec. This can be achieved only when the bath temperature, Tb, is above the melting (liquidus) temperature of the solute material being dropped. A second point of importance is that the refractories used earlier liberated considerable water so that, although the oxygen potential of the atmosphere in the system was satisfactory for work with nickel and copper, it was too high for work with iron, silicon, and so forth. Third, for work at 1550" to 1650°C, an improved temperature-sensing unit is needed. The modified calorimeter in its latest form is shown schematically in Fig. 1. The refractory brick and the Kanthal-Super heating elements which formed the furnace for heating the solute addition have been replaced by a smaller resistance-heated tube furnace which is insulated with bubble-grain alumina. A more elaborate gas purification system was installed to maintain a satisfactorily low oxygen potential in the atmosphere of the calorinieter chamber and of the solute addition furnace. As was the case in the earlier work, at the beginning of a run the calorimeter chamber is evacuated and then filled with purified argon so that a total pressure slightly in excess of 1 atm is maintained during the run. When either of the furnaces within the enclosure attains a red heat, 6 pct H2 is added to the atmosphere. Throughout the run, gas from the calorimeter is circulated through a de-oxidation system at the rate of approximately 5 standard liters per min; the changeover time for the gas within the calorimeter enclosure is approximately 1 hr. The essential stages of the deoxidation system are: a copper furnace at 600°C, a drying tube of anhydrite, and a titanium furnace at 800°C. The oxygen potential of the gas stream in the purification system can be monitored at several points by a stabilized zirconia oxygen cell. This cell is invaluable in detecting the development of leaks in the container vessel and the gas circulating system. The installation of the solute-addition furnace allowed either of two types of temperature-sensing units to be mounted on a water-cooled probe. The first was a small optical device using a silicon diode that was

Jan 1, 1968

By J. G. Savins

Certain types of macromolecules added to water and salt solutions flowing in turbulent motion can reduce the pressure gradient. Alternatively, the volumetric capacity of a pipe for these fluids is increased by the presence of these materials. Examples presented show that the drag reduction can become significant. Thus, the presence of 0.28 per cent of a gum derivative in a solution of sodium chloride flowing at 200 gal/min in a 1.89-in. pipe yields a pressure drop which is 0.44 of the single-phase drop measured under the same conditions of turbulent flow; the addition of 0.1 per cent of a vinyl derivative to a I-in. water line yields a throughput capacity which is 1.78 of the single-phase capacity at the same pressure drop. It is further shown that these phenomena are distinctly different from previous observations with other classes of non-Newtonian systems. There a simple lowering of friction factors below the levels predicted from the resistance laws for Newtonian fluids is associated with a suppression of turbulent motion. A rational physical explanation for drag reduction is advanced. Briefly, the proposed mechanism is a storage by the molecular elastic elements of the macromolecules in solution of the kinetic energy of the turbulent motion. INTRODUCTION This study was inspired by a recent review of some paradoxical drag reduction phenomena in turbulent pipe f1ow.I Under very moderate conditions of turbulent flow, the pressure gradient necessary to pump solutions containing certain specific kinds of polymers, fibers and metallic soaps may become appreciably lower than that required* to pump the solvent, i.e., water or a low-viscosity hydrocarbon, under identical flow rates in the same conduit. As shown by our review, this phenomenon of drag reduction in turbulent duct flow was first noted during the second world war, apparently arising in connection with the development of flame warfare weapons. Since that time several papers illustrating this phenomenon have appeared: Toms, Oldroyd,3 Agoston et al., Bundrant and Matthews, Robertson and Mason,6 Ousterhout and Hall,7 Daily and Bugliarello~ Lummus, Anderson, and Fox. 9 That there are practical applications for techniques which increase discharge or decrease the pressure necessary to transport a liquid through a pipeline is illustrated in the patents which have issued which take advantage of this peculiar phenomenon, e.g., Mysels,l0 Dever, Harbour, and Seifert.11 One also finds fragmentary evidence of this effect in the data pertaining to a few of the polymeric solutions studied by Shaver12 and Dodge.13 However, these investigators were concerned with the development of friction factor vs Reynolds number correlations for a variety of non-Newtonian solutions and suspensions, rather than in a study of drag reduction-. A similar kind of drag reduction effect has been observed in gases. Sproull, for example, reports that adding dust to air flowing in turbulent motion through a pipe results in a lowering of the pressure gradient at identical flow rates. There are also military applications for reducing the drag on hydrodynamic vehicles. For example, the possibility of injecting a rheologically complex fluid into the boundary layers of bodies to reduce the skin friction has been investigated by Fabulal5 and Granville.16 Along somewhat different lines are the drag reduction studies of Kramer.17118 He has shown that skin friction can be reduced by covering the surface of a vehicle with a flexible skin. The effect is apparently due to the boundary layer being stabilized by the presence of the skin. Drag reduction by means of coexisting gas and liquid boundary layers, e.g., film boiling and continuous gas injection, has been proposed by Bradfield, Barkdoll, and Byrne,19 Cess and Sparrow,20'21 Sparrow, Jonsson, and Eckert.22 Here the skin friction occurs between a vapor and a surface rather than between a liquid and a surface. There are several references in the literature to friction-factor correlations for non-Newtonian solutions and suspensions: Shaver and Merri11,23 Dodge and Metzner, Clapp,25 and Thomas.26

Jan 1, 1965

Jan 1, 1891

By Henry M. Rowe

Professor Ruff's most illuminating paper' describing his extremely valuable investigation of the carbon-iron equilibrium diagram assigns definite temperatures to certain very important lines in the diagram, viz.: the eutectic temperature EB (Fig. 1) and the " near-eutectic " temperature E'B', but without indicating clearly enough the reasoning which warrants these assignments. These temperatures are of such primary importance that it is well to indicate the apparent gaps in the reasoning, in the hope that they may be filled in. In his diagram, Fig. 1, the point X and the liues B'D'lII represent the experimental results reached by Ruff and Goecke;a AB, AEB, and SE represent the liquidus, the solidus, and the solubility of the carbon in solid austenite in the absence of graphite according to Gutowsky,3 AB being also in accordance with Spiecker's data; S'E' the solubility of carbon in solid austenite in the presence of graphite according to Ruer and Iljin;5 GS the line A3 after Ooerens and Meyer; 6 and EBC the true eutectic line as inferred by Prof. Ruff from Gutowsky's data. B'D' is the carbon content found in cast-iron which had apparently saturated itself with carbon in the presence of the graphite of the enclosing graphite crucibles in which the determinations were made. From its straightiiess and its sharp inflection near 6.67 per cent. of carbon, the carbon content of

Jan 1, 1913

By L. Himmel, R. F. Mehl, C. E. Birchenall

The rates of self-diffusion of iron in artifically prepared wustites of various compositions have been determined using the decrease in surface activity technique. Similar measurements are reported for artificial magnetites of nearly stoichiometric composition and for natural hematite single crystals. These data, together with appropriate thermodynamic data derived from the present study or from the literature, are used to calculate the rates of oxidation of iron and its oxides, taking as a basis the theoretical rate equations developed by Wagner. The calculations are compared with experimental rate constant data for these same reactions and are shown to provide essential confirmation for the Wagner theory. For the most part, the results are also consistent with the previously proposed transport mechanisms in the oxides of iron. WHEN a metal is exposed to an oxidizing atmosphere at elevated temperatures, a superficial oxide layer is formed which then thickens according to some characteristic rate law. Provided that the oxide layer is dense and continuous and does not present any paths for gaseous diffusion, continued growth must inevitably involve the migration of the reactants—either the metal or oxygen or both—through the lattice of the solid oxide. This is true whether the reaction rate is controlled by the diffusion process itself or by a slow step in a reaction at one of the interfaces. If the overall rate is limited by diffusion, and if the concentrations or thermodynamic activities of the reactants at the boundaries of the oxide layer are independent of time, the familiar parabolic rate law is observed. Under these conditions, Wagner1 has shown that the rate constant may be expressed in terms of the mobilities of the reacting components and the appropriate concentration or activity gradients which are established across the growing oxide layer. In presenting the phenomenological basis for the theory, Wagner has emphasized the role played by lattice defects in diffusion processes in oxides. The essential validity of this theory has been confirmed by experiment for a number of simple systems including the growth of Cu2O on copper.'-' One of the objectives of the present study has been to extend the Wagner approach to the more complex process of the oxidation of iron and its oxides, and particularly to wustite, which is normally the major constituent of the oxide scales formed on iron at temperatures above approximately 570°C. For this purpose the rates of self-diffusion of iron in w?stite, magnetite, and hematite have been measured by tracer techniques and the necessary thermodynamic data have been obtained from equilibrium studies involving the oxides and their atmospheres. These data have subsequently been used to test the underlying assumptions of the Wagner theory as well as the detailed mechanism of the scaling of iron previously proposed by Davies, Simnad, and Birchenall.5 Lengthy treatments of diffusion and conduction phenomena in ionic crystals have been published." * The latest, by Jost,8 also summarizes much of the existing experimental data. In general, however, the oxides of iron have not been considered specifically and hence a brief review of the available

Jan 1, 1954

Aamot, Olav Crone, (M'29) Chem. Engr., Elektrokemisk, Raadhusgt. 23, Oslo, Norway. Abadilla, Quirico A., (M'3S) Min. Engr., Dir., Bu¬ reau of Mines. Manila, P. I. Abbott, Agatin Townsend, (J'40) Jr. Engr., Phelps Dodge Corp., Morenci Branch, Morenci. Ariz. Abbott, Clarence E., (M'04) Civil Engr., V.P., Ten¬nessee Coal Iron & R.R.. Co., 1542 Brown -Marx Bldg.. Birmingham, Ala. Abel, Raymond L., (M'28) Chem. Engr., Command¬ing, Officer, Pittsburgh Chem. Warfare Procurement Dist., American Bank Bldg., Pittsburgh. Pa. Abel, Walter D., (M'32) Alin. Engr.. Div. of Cor¬porations, State of Calif., 403 California State Bldg., Los Angeles, Calif. Abele, Louis T., (M'31) 423 3rd Ave., Decatur, Ga. Abell, Leo M., (M'31) Mill Supt. & Met., Emperor Gold Min. Co., Led., Vatnkoula, Fiji Islands. Abernathy, G. E., (M'38) Geol., Kansas State Geol. Survey, Pittsburg, Bans. Abernathy, Jack H., (M'40) Peer. Engr., c/o Superior Oil Corp., National Bank of Tulsa Bldg., Tulsa, Okla. Aborn, Robert H., (M'10) Asst. Met., Research Lab., U. S. Steel Corp., Lincoln Highway, Kearny, N. J. Abraham, A. W., (M'39) Peer. Engr., Richfield Oil Corp., 555 S. Flower St., Los Angeles, Calif. Abramowitz, William L., (J'40) Chem., Industrial Inventions, Inc., 103 Foster Se., Peabody, Mass.

Jan 1, 1942

By R. B. Russell

SINCE Cahn's¹ paper on plastic deformation in orthorhombic (a) uranium an increasing amount of work is to be expected on orientation of single crystals and preferred orientation in this metal. It would seem desirable to have a table of angles between crystallographic planes (hkl) and (HKL). Table I shows these angles as distances from (loo), (0l0), and (00l), and in Fig. 1 as a standard (001) stereographic projection. Only the locations of poles whose diffracting planes produce Cu Ka reflections up to 0 = 70.5" (i.e. (154) ) are given." The relative reflection of these planes are represented by circle diameters. It is hoped that the projection may also be used in making inverse pole figures, originally suggested by Harris.' Values of 4 were calculated from the expression hH kK 1L cos = hH/a²+kK/b²-lL/c² where the lattice parameters a, b, c, and the spac-ings d were taken from the work of Jacob and Warren." (They report a = 2.852 kX (2.8578 A), b = 5.865 kX (5.8768 A), c = 4.945 kX (4.9550 A).) The parameters reported by them may be subject to revision,4,5 accordingly the interplanar angles are listed to only the nearest tenth of a degree. References ¹R. W. Cahn: Acta Metallurgica (1953) 1, p. 49. ¹G. B. Harris: Philosophical Magazine (1952) 43, p. 113. 3C. W. Jacob and B. E. Warren: Journal ACS (1937) 59, p. 2588. 4J. S. Lukesh: Acta Crystallographica (1949) 2, p. 420. ³ J. Thewlis: Nature (1951) 168, p. 198.

Jan 1, 1954

By Edna A. Dancy, Gerhard J. Derge

The specific conductance of FeOx,-CaO melts in contact with iron was found to decrease from 200 ohm-1 cm-1 for FeO, to 40 ohm-1 cm-1 for a melt containing 26.3 pct CaO at 1400°C. The temperature coefficient was positive at all compositions, but became smaller at high CaO contents. Current efficiencies for electrolysis increased from 2.5 pct in FeOx to 17.3 pct at the high CaO composition, indicating a change from predominantly electronic conduction to conduction with a substantial ionic contribution. It was shown that Ca++ ions as well as Fe++ ions carry the ionic current. A subsidiary investigation on the apparent effect of atmospheres of argon, helium, and nitrogen on the electrical conductivity showed that this could be correlated with surface temperature losses, which varied with the thermal conductivities of the gases and resulted in precipitation of metal by the reaction 3 Fe++ = 2 Fe+++ + Fe. The work described in this paper is offered as a contribution to the general fund of knowledge concerning metallurgical slags. Measurement of electrical conductivity and electrolysis are comparatively trouble -free methods for investigating molten materials, but, although these methods had been used for complex slags, it was not until the work of Bockris et al.1 that the approach of examining simple binary slag systems was employed, and CaO-SiO2, MnO-SiO2, and Al2O3-Si9 were studied. Two groups have performed work of particular relevance to the present investigation. Inouye, Tomlinson, and chipman2 studied the conductivity of wustite as a function of temperature and of the addition of 5 mol pct of a number of oxides, including CaO. They concluded that molten FeOx in equilibrium with iron is a semiconductor. Simnad, Derge, and ceorge3 demonstrated the ionic nature of liquid iron silicate slags and also concluded that, although the conductivity of FeOx in equilibrium with iron is predominantly electronic in nature, there is a small ionic contribution. The work reported here on FeOx,-CaO slags consists of three main parts, namely, the determination of the specific conductance over a wide composition range, an investigation into the nature of the conductivity through current-efficiency measurements over the same composition range, and an attempt to identify the current-carrying ions, as well as a subsidiary investigation on the apparent effect of the nature of the inert atmosphere on the conductivity. EXPERIMENTAL Materials. The slags, varying in composition from FeOx to 27 pct CaO, were prepared by heating reagent- grade Fe2O3 in an ingot iron crucible with a suitable amount of CaCO3 and, in some cases, powdered iron, in air. This prefused material was then used for the runs. At the end of each run the cell was removed from the furnace and quenched by immersing the bottom half in water. After crushing, the slags were analyzed for calcium and total iron by the usual wet methods. The oxygen content was obtained by difference. Specific Conductance: Apparatus and Method. Fig. shows the experimental setup, with the conductivity cell and leads of ingot iron. The standard four-probe method for measuring high conductivities was used. In this, the potential drop across the unknown resistance is compared with the potential drop across a known resistance connected in series, i .e., same current through both resistances. Thus there are both current and potential leads to the center electrode and to the crucible, which acts as th other electrode. Both ac and dc circuits were available for the measurements; they have been described in earlier work performed in this laboratory.4,5 The geometry of the cell was such that the center electrode was equidistant from the bottom and sides of the crucible. This ensured that the current path was the same irrespective of the magnitude of the conductivity of the material in the cell. Cell constant were measured with KC1 or NaCl solutions, which have considerably lower conductivities (0.0013 to 0.25 ohm-' cm) than the slags, and this precaution in design made sure that the determined cell constants applied to the cells with contents of any conductivity. The cell-constant determinations were made with the ac measuring circuit to prevent polarization. The four-probe method eliminates lead resistance but not the resistance of those parts of the center

Jan 1, 1967

RECORDING that the latest annual meeting was the largest and most successful ever held has be-come almost a habit, but when, as this year, the registration on the first day exceeded any other first day by two hundred, the annual dinner attracted nearly 1200, as compared with 750 at the previous largest one, and the number of technical sessions was larger than ever before, there seems no escape from so regarding it. In spite of the third day being a legal holiday (Washington's Birthday) no slackening, in attendance and interest was noted, and throughout the four days the greatest problem was to find enough meeting rooms and chairs to provide for the sessions, of which as many as twelve were in progress at one time. Solution of the problem would not have been possible (since the Engi-neering Societies building, was designed to provide only three general meeting rooms) except that a part of the eighth floor happened to be temporarily vacant. As these extra rooms will not be available next year, it may become necessary to adopt measures to keep the annual meeting down to the limit of facilities for handling it. The meeting opened on Monday with simultaneous sessions on iron and steel, geophysical prospecting, mine ventilation, non-metallic minerals, and milling, methods. The first four, which were continued after the usual recess for lunch, are reported in more detail elsewhere.

Jan 3, 1928

By R. W. Raymond

The death of Louis Janin, which took place Mar. 6, 1914, at Santa Barbara, terminated the earthly career of almost the last survivor, and one of the most illustrious members, of that group of American mining engineers and metallurgists who, in the last quarter of the nineteenth century, directed the development of the mineral resources of the Pacific slope. Louis Janin was born in 1836 at New Orleans. His grandfather, an officer in the French army, had emigrated to this country, with his family, at or before the outbreak of the French revolution. His father became an

Jan 1, 1915

By K. G. Wikle, W. W. Beaver

A general survey of the mechanical properties of commercially pure beryllium fabricated from powder by vacuum hot pressing and other consolidation methods is presented. The effect of fabrication method, grain size, strain rate, and directionality upon both room and elevated temperature tensile properties is reported. BERYLLIUM metal, in spite of its rather restricted use, has been the object of attention for many researchers in the past half century. However, such work was performed on special experimental lots of metal made in small quantities by a variety of reduction methods. Not until 1946 was there a substantial production of beryllium metal, and not until 1950 was there a steady production of a commercially standard beryllium in the United States. This output was both the result of a requirement of the Atomic Energy Commission for a high grade beryllium of consistent quality and the development of a powder metallurgy process, by the Brush Beryllium Co., known originally as Process Q, which yielded a fine grained beryllium suitable for fabrication. Because this powder metallurgy product, known as QMV, superceded other types of metal made previously and represents the great majority of beryllium in use today, it seems worthwhile to present the results of studies on the mechanical properties of this metal as currently made. To the design engineer and the metallurgist, beryllium has extremely interesting properties. It is as light as magnesium alloys while having a stiffness modulus 40 pct greater than steel and a strength-weight ratio superior to titanium and aluminum alloys and aircraft steels. The melting point is high, 1287°C (2348°F), and it has good corrosion resistance both in air and water. Also, it is highly transparent to X-rays and has good heat and electrical conductivity (electric conductivity is greater than 40 pct of Cu). To the atomic energy program beryllium is considered a valuable material because of its low neutron-capture cross section and high neutron-scattering cross section which make it a good moderator and reflector for the lower velocity neutrons. A major technical difficulty limiting the use of beryllium, especially in structural applications, has been its notch sensitivity and consequent room temperature brittleness. Kaufmann, Gordon, and Lillie1 have reported their work on the mechanical properties of beryllium performed from 1946 to 1950. They studied the room and elevated temperature properties of cast and extruded beryllium and extruded electrolytic flake, Table I. Cast and extruded alloys of 85 to 99 pct Be were tested also. They found that extruded metal developed good strength and appreciable ductility in the extrusion direction and that thermal treatment and alloying provided little improvement in mechanical properties. They concluded that preferred orientation and fine grain size were the means of obtaining optimum tensile properties in beryllium. Other investigators have measured and commented on one of the most striking mechanical properties of beryllium, namely, its abnormally low Poisson's ratio.2 Udy, Shaw, and Boulger3 presented the latest published survey on properties of beryllium but their information is based only on published data available before April 1949 and cites little information on metal fabricated by powder metallurgy

Jan 1, 1955

By T. A. Read, H. K. Birnbaum

STRESS-induced twin boundary motion in the AuCd ß'phase (52.5 at. pct Au 47.5 at. pct Cd having an orthorhombic structure (space group D h)' was discussed for the case of transformation twins.' Mechanical twinning, i.e., introduction of new twin orientations by the applied stress was sometimes observed in the ß' phase which contained two transformation twin orientations. (See Ref. 2 for experimental details.) The transformation twins terminated at the mechanical twin boundary; the two initial orientations having been twinned to the new orientation as shown in Fig. l. In a "hard" tensile instrument, formation of each mechanical twin was accompanied by a sharp drop in load (and an audible click) resulting in a typical serrated load-extension curve. The mechanical twins increased in width and additional twins were nucleated as the load increased until the entire specimen was occupied by the mechanical twin orientation. A restoring force2 caused the mechanical twin and transformation twin boundaries to return towards their initial configuration on releasing the load. In a stabilized specimen* the total strain introduced by mechanical twinning was recovered on releasing the applied stress. Initial and final microstructures were identical. After decreasing gradually to a critical width, mechanical twins suddenly disappeared accompanied by audible clicks and sharp increases in load (measured at a constant rate of crosshead motion in a "hard" machine). Mechanical twins could be stabilized in any position by maintaining the applied load for a sufficient time, indicating a decrease in restoring force with time similar to that observed for transformation twins.' Orientation relationships for mechanical and transformation twins were determined and are shown in Fig. 2. The mechanical twin, T3, was twin related to transformation twin, T,, by reflection in (1ll), and twin related to transformation twin, T2, by reflection in (111)T, . T, was related to T, by reflection in(ll1)T1 . The "average" mechanical twin composition plane lay several degrees from (1ll), . In every specimen which mechanically twinned, orientation T3 was most highly favored by the applied stress, i.e., it was the twin orientation which provided the greatest change in length compatible with the direction of applied stress

Jan 1, 1961

By Robert Isaac Williams

The Questa mine is located in northern New Mexico on the western flank of the Sangre de Cristo Mountains about 75 miles north of Santa Fe and ranges in elevation from 6,800 to 10,000 ft. GEOLOGY The rocks of the area are Precambrian metamorphic rocks covered by Tertiary extrusive andesites and rhyolites and intruded by Tertiary granitic rocks. These Tertiary intrusives are localized in an east-west belt about 20 miles long and 2 miles wide, extending from Questa to Red River. The Questa orebody is associated with a north-trending aplite intrusive about 3/4 mile wide and 1 3/4 miles long. In the area of mineralization, the metasomatism of aplite has produced a mottled porphyritic rock. This hybrid rock has caused much of the controversy about the Questa mine intrusive. The orebody is essentially monomineralic and consists of numerous closely spaced molybdenite veins varying in thickness from ' 'paint" to 3 in. and occurring in both the andesites and the intrusive. In the intrusive the veins are often siliceous. Common alteration minerals associated with the molybdenite ore vary with the original composition of the rock. The alteration of the aplite has produced phenocrysts of orthoclase, albite, oligoclase and biotite; veins of quartz, orthoclase, and biotite; and graphic myrmekitic intergrowths of feldspars and quartz. In many places near the contact, the andesite is indistinguishable from the metasomatized aplite. The dominant alteration in andesite, however, is the development of fine-grained biotite with apatite, rutile, and sphene.

Jan 1, 1969

(There are 82 Local Sections in the United States, 10 Foreign) ADIRONDACK Established June 18, 1952 Official year begins in January Meets next to last Saturday monthly April through October Local Section Dues AIME Mbrs $2 Affiliate Mbrs $3 Severn P Brown, Chairman George E Erdman, Vice-Chairman Patrick F Farrell, Secretary-Treasurer Republic Steel Corp Mineville, N Y

Jan 1, 1960

By T. B. Counselman

PROBABLY the earliest concentration of iron ore in this country was carried on in the northeastern magnetite areas. Magnetic concentration was relatively simple and gave a concentrate that, after agglomeration, and in spite of being high in phosphorus because of the dry concentrating methods then in use, was satisfactory blast-furnace feed. Production from the northeastern magnetite area languished after the discovery and development of the Lake Superior ores, where there was seemingly an unlimited tonnage of high-grade ore, first the Michigan ores, and subsequently the still larger deposits of Minnesota. For years only the higher grade, direct shipping ores of the Lake Superior district were mined. Those of Michigan, and of the Vermilion Range in Minnesota, were hard ores and came principally from underground mines. The softer ores of the Mesabi came partly from underground mines, but mostly from the enormous deposits that could be worked by open-pit methods. The costs of ore from these open-pit deposits, even with the high initial cost of stripping, were so low that the underground mines of the Mesabi could hardly compete. The so-called Old Range ores, of Michigan and of the Vermilion Range of Minnesota, were hard and lumpy, and opened up the burden in the blast furnace, therefore making possible harder driving with greater output. Also, some of these ores were of such grade and physical characteristics that they were suitable for charge ore in the open hearth. These ores, therefore, commanded a price premium, and could compete with the softer, finer, but cheaper, Mesabi ores. The big tonnage reserves, however, are on the Mesabi, and it is these big open-pit deposits that constitute our stock pile of iron ore, from which we are drawing so heavily during this war period. On the western end of the Mesabi the ore was found to be high in silica, and not suitable as furnace feed. As early as 1902, attempts were made to concentrate this so-called wash ore and by 1910 the first washing plant was put into operation. The process was very simple, consisting essentially of a sizing and washing operation, with scalping screens, logwashers, and tables, which later were replaced by classifiers. Ore particles finer than 100 mesh were deliberately wasted, because these fines were undesirable in the furnace. Fortunately, these tailings were impounded, and already are being reworked. Before long some of the low-grade ores began to require more elaborate treatment than the simple washing operation and, tables having been discarded because of their low capacity, in favor of classifiers, jigs were next introduced. These were able to discard coarser pieces of tailing than classifiers. Jigs are in active use today, various improvements having been made in their design and application. Various other machines and methods of concentration have been tried from time to time, and have in turn been discarded for more improved processes. The latest and most important process that has been

Jan 1, 1943

By Hiram B. Woon

Uranium ore deposits in the Lisbon Valley area are in an arcuate belt, 15 miles long by one-half-mile wide, on the southwest flank of the Lisbon Valley anticline. They range in size from 500 to 1,500,000 tons and by mid-1965 had yielded 6,147,000 tons containing 48,530,000 pounds of U3O8. Ore bodies average 6 feet thick, are tabular, amoeba-shaped masses, concordant to the bedding, and are in the thickest, lowest sandstone unit of the Moss Back Member of the Chinle Formation of Triassic age. The host rock is predominantly a fluviatile, calcareous, fine-grained to conglomeratic sandstone. Uraninite, the principal ore mineral, fills the pores in the sandstone and partly replaces sand grains and fossil wood fragments. During Late Permian and Early Triassic time pre-Chinle Formations were arched to form the ancestral Permian anticline. Moss Back streams truncated Moenkopi and Cutler beds which capped the ancestral anticline and then covered it with fluviatile elastics, which were subsequently covered by thousands of feet of Triassic, Jurassic, and Cretaceous sediments. Uranium, probably derived from the Chinle Formation by diagenetic processes, was transported in connate ground waters, was moved by compaction or hydrostatic forces, and was deposited under reducing conditions. Uranium was emplaced around the crest of the ancestral anticline, prior to the Laramide orogeny. During the orogeny, the Tertiary-Lisbon valley anticline was super induced on the Permian anticline and, penecontemporaneous with uplift, was faulted parallel to its longitudinal axis. The Big Indian ore belt on the southwest flank footwall block was elevated to approximately its present position, and the northeast flank hanging wall block was elevated only slightly. An extension of the Big Indian ore belt around the northeast flank of the ancestral Permian anticline may exist in the Moss Back sandstone in the downthrown block northeast of the Lisbon Valley fault.

Jan 1, 1968

By T. B. Counselman

Probably the earliest concentration of iron ore in this country was carried on in the northeastern magnetite areas. Magnetic concentration was relatively simple and gave a concentrate that, after agglomeration, and in spite of being high in phosphorus because of the dry concentrating methods then in use, was satisfactory blast-furnace feed. Production from the northeastern magnetite area languished after the discovery and development of the Lake Superior ores, where there was seemingly an unlimited tonnage of high-grade ore, first the Michigan ores, and subsequently the still larger deposits of Minnesota. For years only the higher grade, direct shipping ores of the Lake Superior district were mined. Those of Michigan, and of the Vermilion Range in Minnesota, were hard ores and came principally from underground mines. The softer ores of the Mesabi came partly from underground mines, but mostly from the enormous deposits that could be worked by open-pit methods. The costs of ore from these open-pit deposits, even with the high initial cost of stripping, were so low that the underground mines of the Mesabi could hardly compete. The so-called Old Range ores, of Michigan and of the Vermilion. Range of Minnesota, were hard and lumpy, and opened UP the burden in the blast furnace, therefore making possible harder driving with greater output. Also, some of these ores were of such grade and physical characteristics that they were suitable for charge ore in the open hearth. These ores, therefore, commanded a price premium, and could compete with the softer, finer, but cheaper, Mesabi ores. The big tonnage reserves, however, are on the Mesabi. and it is these big open-pit deposits that constitute our stock pile of iron ore, from which we are drawing so heavily during this war period. On the western end of the Mesabi the ore was found to be high in silica, and not suitable as furnace feed. As early as 1902, attempts were made to concentrate this so-called wash ore and by 1910 the first washing plant was put into operation. The Process was very simple, consisting essentially of a sizing and washing operation, with scalping screens, logwashers, and tables, which later were replaced by classifiers. Ore particles finer than 100 mesh were deliberately wasted, because these fines were undesirable in the furnace. Fortunately, these tailings were impounded, and already are being reworked. Before long some of the low-grade ores began to require more elaborate treatment than the simple washing operation and, tables having been discarded because of their low capacity, in favor of classifiers, jigs were next introduced. These were able to discard coarser pieces of tailing than classifiers. jigs are in active use today, various improvements having been made in their design and application. Various other machines and methods of concentration have been tried from time to time, and have in turn been discarded for more improved processes. The latest and most important process that has been

Jan 1, 1947

By T. B. Counselman

Probably the earliest concentration of iron ore in this country was carried on in the northeastern magnetite areas. Magnetic concentration was relatively simple and gave a concentrate that, after agglomeration, and in spite of being high in phosphorus because of the dry concentrating methods then in use, was satisfactory blast-furnace feed. Production from the northeastern magnetite area languished after the discovery and development of the Lake Superior ores, where there was seemingly an unlimited tonnage of high-grade ore, first the Michigan ores, and subsequently the still larger deposits of Minnesota. For years only the higher grade, direct shipping ores of the Lake Superior district were mined. Those of Michigan, and of the Vermilion Range in Minnesota, were hard ores and came principally from underground mines. The softer ores of the Mesabi came partly from underground mines, but mostly from the enormous deposits that could be worked by open-pit methods. The costs of ore from these open-pit deposits, even with the high initial cost of stripping, were so low that the underground mines of the Mesabi could hardly compete. The so-called Old Range ores, of Michigan and of the Vermilion. Range of Minnesota, were hard and lumpy, and opened UP the burden in the blast furnace, therefore making possible harder driving with greater output. Also, some of these ores were of such grade and physical characteristics that they were suitable for charge ore in the open hearth. These ores, therefore, commanded a price premium, and could compete with the softer, finer, but cheaper, Mesabi ores. The big tonnage reserves, however, are on the Mesabi. and it is these big open-pit deposits that constitute our stock pile of iron ore, from which we are drawing so heavily during this war period. On the western end of the Mesabi the ore was found to be high in silica, and not suitable as furnace feed. As early as 1902, attempts were made to concentrate this so-called wash ore and by 1910 the first washing plant was put into operation. The Process was very simple, consisting essentially of a sizing and washing operation, with scalping screens, logwashers, and tables, which later were replaced by classifiers. Ore particles finer than 100 mesh were deliberately wasted, because these fines were undesirable in the furnace. Fortunately, these tailings were impounded, and already are being reworked. Before long some of the low-grade ores began to require more elaborate treatment than the simple washing operation and, tables having been discarded because of their low capacity, in favor of classifiers, jigs were next introduced. These were able to discard coarser pieces of tailing than classifiers. jigs are in active use today, various improvements having been made in their design and application. Various other machines and methods of concentration have been tried from time to time, and have in turn been discarded for more improved processes. The latest and most important process that has been

Jan 1, 1947

By George Young

DURING the spring of 1910 I visited a number of open-pit brown-coal mines and underground workings in the vicinity of Halle, Halberstadt, Leipsic, Cologne and Bonn. The notes which I took and the observations which I made at the time have been condensed and make up the principal part of this paper. Certain supplementary information has been taken from several sources which are given in the paper. The mining of brown coal is one of the important industries of Germany. The coal varies in color from dark brown to almost black and is soft like loam. Pieces of wood and strips of bark and, even parts of tree trunks are frequently encountered in the excavation although the coal for the most part consists of a pulverulent, more or less matted mass of small particles of vegetal matter. It is a product between peat and lignitic coal. An analysis, taken from Coal Resources of the World shows the approximate composition of the material: Moisture, 53.73 per cent.; ash, 4.98; fixed carbon, 18.08; volatile carbon, 23.31 per cent. The principal characteristic is the amount of moisture. This seldom runs less than 48 per cent. The ash is usually low and ranges from 5 to 10 per cent. The sulphur content is usually less than 0.5 per cent. The heating effect of the fuel ranges from 2,000 to 2,500 calories.

Jan 2, 1916

By H. L. Riley, B. W. Gandrud

AS far as the present writers know, this system of flotation has not been used elsewhere in this country, but in the last couple of years it has been introduced, with minor variations, at one plant in England and one in Wales.' The system has been described and discussed in a number of publications.2-5 The following is quoted from an abstract of the latest of these,5 a paper presented at an International Conference on Industrial Combustion in 1952. On the basis of experience to date with the commercial plants, it is believed that the kerosene-flotation process incorporates all the necessary elements to make it greatly superior to anything else now available for treating of fines in wet processes of coal preparation. Additional study and investigation are still needed, however, to determine if certain phases of the process can be improved to such an extent as to make it generally satisfactory and acceptable to the industry. Further improvements will be needed with respect to the capacities of the flotation cells and the reagent consumption. The situation referred to above explains why an investigation is being made of the possibilities of achieving better cell capacities. Results obtained from this investigation, which is still in progress, are believed significant with regard to both cell capacity in general and the relation of cell design to cell capacity in particular. Commercial equipment now being used in a laboratory-type investigation should have performance characteristics similar to those of the larger machines. Equipment and Procedures: All flotation tests have been made in a standard Denver sub-A 24x24-in. unit cell of 12-cu ft volume. Cell modifications to make it more suitable for the tests were an adjustable front-wall section for varying cell depth and a perforated scraper-drag assembly for removal of the float product. There is also an apron dry-coal feeder, a gravity-feed water supply, reagent feeders, and a centrifugal pump that feeds the mixture of coal, water, and reagents into the flotation cell. A wattmeter connected into the drive-motor circuit records the power requirements of the impeller throughout each run. Dry coal, water, and reagents are all fed through a pan-type intake to the feed pump. A Sturtevant blower was set up to furnish air for supercharging. A centrifugal pump with a garbage-can intake provides for disposal of refuse flow to an outside settling tank. Figs. 1 and 2 show the flotation cell; Fig. 2 also illustrates the blower for supercharging. For purposes of this investigation, the percentage by weight of the feed coal recovered in the float product under a standard set of conditions has been considered as the criterion of cell capacity. The authors realize that such a criterion may be somewhat unorthodox, as the term cell capacity is usually understood to refer to feed input and ordinarily takes into account the ash analyses of the float product and refuse. However, the word capacity is flexible enough so that Webster gives one definition as maximum output, a definition which seems to justify, at least partly, acceptance of the above criterion. It has been the authors' experience in the Birmingham district that the ash-reduction efficiency of the coal-flotation process is generally satisfactory and that the only real problem is to increase the rate of float recovery so that the feed rate to any given bank of cells can be increased without undue loss of coal in the refuse. Originally it was planned to operate the flotation cell to simulate continuous operation during sampling periods. It was assumed that operating for reasonable time with feed coal, water, and reagents turned on would stabilize conditions so that the weight of float coal discharged during a fixed time interval would be an accurate measure of the rate at which the coal was being floated. It developed, however, that this supposition was erroneous. The float coal, caught for fixed time intervals and weighed, gave widely varying results in duplicate runs. Efforts to correct this trouble failed, and it was decided to try to operate on a batch-test basis, whereby all the float coal produced during a run on a known weight of feed coal would be caught in tubs, dewatered, and weighed. This method gives consistent and reproducible results, with total float product weight rarely varying by more than 3 or 4 pct on duplicate runs. The standard test procedure is as follows: A 132-lb sample of dry feed coal is weighed and placed in the feed hopper. The feeder is adjusted for a rate of 800 lb per hr. Feed water and reagents are turned on, and the feed and refuse pumps are started. One minute later the impeller is started. Six minutes are allowed for the cell to fill up with the water-reagent mixture. The feed of dry coal is started at the end of this 6-min period. One minute later the float-coal removal drag is started. The float coal is caught in one tub for the first 6 min after the flow of feed coal starts. Tubs are then changed, and the float coal is caught in a second tub until the feed coal runs out, when the tubs are again interchanged to catch the float coal for the remainder of the run in the first tub. The cell is kept running for 3 min with the water and reagents on after the feed stops to allow residual float coal to be removed. At the end of a test the wet float coal in both tubs is weighed and the total weight recorded. The product in the second tub is used for moisture determination and screen-size analyses. When the

Jan 1, 1956