Search Documents

By Frank Firmstone

IN the early decades of the past century the method of starting iron blast-furnaces by "scaffolding-down" seems to have been in universal use for coke-furnaces and, at least in this country, for charcoal-furnaces also. It was likewise used at some of the early anthracite-furnaces, as is stated in the important "Reminiscences" printed by the late Samuel Thomas. I It had been generally superseded in Great Britain as early as 1850, by some variations of the plan now used, and was rarely used when Percy wrote.' On the Continent it was still followed in the 60's,3 and was elaborately described by Valerius in 1852. I have never read any statement as to when and by whom '4 scaffolding" was first dispensed with, but the following extracts from journals of my father seem to fix an authentic date for an instance in this country:

Mar 1, 1907

By M. van Swaay, C. E. Birchenall

Palladium has a large capacity for the dissolution or occlusion of hydrogen; the gas also diffuses very rapidly through the metal. Palladium thimbles are widely used in the laboratory for purification of hydrogen by diffusion. The use of palladium filters could be extended to several large-scale applications if greater stability of the permeation process could be attained. In this paper a number of aspects contributing toward this goal are discussed, and new data on solubility and diffusivity are given. Palladium sheets of 0.005, 0.010, or 0.020 in. thickness were prepared by three procedures: casting and rolling, sintering palladium powder, and sintering palladium powder to which 0.1 pct thorium oxide had been added. Half-inch diam circular specimens were cut and clamped in a stainless steel holder provided with knife edges to seal the palladium sheet with soft copper gaskets. The seals were tested for leaks at l0-5 mm Hg. No difficulties from this source were encountered even after many temperature cycles in the system. The holder was silver-soldered to Kovar-glass seals and attached to the system through glass ball joints. Each joint was sealed with Apiezon wax and was adjacent to a cold trap. In several experiments the holders were fused directly into the system, eliminating the ball joints, to show that the wax did not affect the filter. Three filter holders were supported in holes in a stainless steel cylinder, which also acted as a temperature equalizing block inside the resistance wound furnace. The measuring thermocouple was inserted in one of the holders. A potentiometric controller with control thermocouple on the furnace heater winding maintained ± 0.2oC. Electrolytic hydrogen was purified and stored as shown in the flow diagram, Fig. 1. It could be admitted to either or both sides of the palladium specimens. Only a mechanical pump was used, for even high pumping speeds would not bring the pressure on the off-gas side of the filter below 10 to 50p Hg owing to the rapid hydrogen flow through the filters. A series of steady-state permeability studies allowed identification of several conditions of permeability loss. A constant fore pressure was maintained while the low-pressure face was pumped. After enough time had elapsed for a steady flow to be established the pump was cut off, and the rate of pressure increase in a thermostated bulb was measured to determine the flow rate. The time delay method of Daynes1,9 was adopted since it offered the possibility of determining solubilities and diffusivities. For each measurement both sides of the filter were evacuated for 15 min, which gave about 10-4mm Hg residual pressure. Hydrogen was admitted to one side or the other of the filter at a fixed pressure. The pressure on the off-gas side was observed as a function of time. A

Jan 1, 1961

By W. P. Sykes

SEVEN years ago, Dr. S. L. Hoyt1 presented a masterful discussion of the hard metal carbides and cemented tungsten carbide. His lecture summarized most of the data then available in the field; many of the details relating to the production, properties and structure of cemented tungsten carbide had never been previously published, for, in fact, this information was only then being acquired. During the intervening years, the cemented carbides have assumed a place of real importance in the commercial field, with an ever widening variety of applications due to constant improvement in the control of production technique and the unremitting search for new compositions that might better the performance of the alloys in one or another type of service. The most recent summary of production methods, properties and guides for the successful application of the cemented carbides appears in the 1936 edition of the Metals Handbook. Of necessity, much detailed information relating to structures and physical properties is not included in such a summary, and it is with such details that the present discussion is concerned.

Jan 1, 1938

Report of the Secretary TO THE BOARD OF DIRECTORS OF THE AMERICAN INSTITUTE OF MINING AND METALLURGICAL ENGINEERS Gentlemen:-To a Board of Directors keeping in as close touch with all of the affairs under their care as do the Board of Directors of the A. I. M. E., through their monthly meetings, a report of the year's progress is almost superfluous. To the members who read the monthly reports of. the Board Meetings and of the various activities of the Institute as published each month, a yearly report cannot carry much fresh information; yet for both it may be well, as is the custom, to glance over the field of our activities during the past year, and to make an estimate for the year to come. The beginning of 1924 was not propitious for the members of the mining profession, though tonnage production for 1923 had been high and the gross value higher than for several years. The margin of profit had been narrow, prospecting and development were limited, and many of our members were unemployed, or were working in other industries. Toward the end of the year, higher metal, prices were in sight. Old-time optimism began to grow, and it now brightens the outlook for 1925. An excellent barometer of the prosperity of the industry, and that of the Institute, for they go hand in hand, is the work of our Employment Bureau. During the past few months, the percentage of our members for whom openings have been found has been increasing to a marked extent, and many members who had fallen in arrears are placing themselves in good standing. The number of new members joining has remained about as it was in 1922 and 1923. The Directors have reason to congratulate themselves on the interest maintained during a dull period, for it is not humanly possible to take a keen interest in the technology of an industry when our hands and minds are not actively engaged in it Now, with a much brighter outlook, we can look forward to a year of increasing prosperity for the industry and for the Institute.

Jan 3, 1925

By Michael Perch, Charles C. Russell

Nearly 75 per cent of the total coke production in the United States in 1940 was consumed in blast furnaces. In 1939 the percentage was 69.9, and in 1938 it was 61.3. To produce a net ton of pig iron 1757 lb. of coke was required in 1940 and 1760 lb. in 1939. These figures indicate how dependent the production of pig iron is upon the production of coke. The rate of iron production is in some measure influenced by the physical and chemical characteristics of the coke. Blast-furnace operators believe that the physical properties of coke profoundly influence the operation of the furnace. Although it is true that coke of a wide variety of physical properties is used in American blast furnaces, the periodic fluctuation of these properties is one of the causes of irregularity of blast-furnace operation. The purpose of this paper is to present a broad picture of the physical properties of by-product coke that are generally considered to be important by coke-oven and blast-furnace operators. Effects of the kind of coal used, the preparation of the coal, the rate of coking, and other factors will be considered. Of all these variables, the kind of coal used is by far the most important. In this discussion use will be made of the method of coal classification by rank' standardized by the American Society for Testing Materials. Although this method of classification has been an American stand¬ard for several years, it has not been given the attention it deserves, especially in connection with the selection of coal for production of coke. Despite the fact that many producers of blast-furnace coke are limited to some particular source or sources of coal, a good understanding of the principles involved in setting up the standard method of classification may lead to a better appreciation of the causes of changes in coke characteristics. Furthermore, where it is necessary to select new coals as a substitute for the original supply, this method of classification can be of great assistance. The data presented have been gathered from many sources, but no attempt has been made to cover the vast literature. Instead, some of the more important data have been selected to show how coals and their carbonization affect some of the physical properties of coke. It must be emphasized that generalizations concerning the behavior of coking coals are presented and that individual coals may vary widely from the specific behavior depicted. Nevertheless, it is believed that the data illustrate certain typical behaviors. Neither was it possible to cover completely all the factors involved; for example, the macroscopic constituents of coal are believed to have important effects on the physical properties of coke, but since there is little information available for such study, and since vitrain, clarain, and durain are neither

Jan 1, 1944

By D. H. Newland

CERTAIN observations from the field and laboratory suggest the need for recasting some of our ideas about gypsum as a rock-forming mineral and in relation to supplies for industrial use. Until about 25 years ago, the use of gypsum was confined almost entirely to agriculture. During the past quarter century, though, its usefulness has been greatly developed, particularly in the building trades, which now absorb most of the gypsum produced. In 1919, according to the U.S. Geological Survey, the output of crude gypsum was 2,240,163 tons, a gain of 912 per cent. in 25 years. About one-half of this production was mined in New York, Ohio, and Michigan, where the proved supplies can hardly be regarded as over-large when viewed in relation to the rapid expansion of industrial requirements. The occurrence of gypsum in the United States is treated by R. W. Stone and others.1 The deposits of Canada are described by L. H. Cole.2 Several states, including Kansas, Oklahoma, Iowa, Michigan, and New York, have had special surveys made their of gypsum deposits, but the reports, as a rule, refer to conditions as they existed from 15 to 20 years ago.

Jan 9, 1921

By F. H. Wilson, R. M. Brick

With the papers of Palmer and Smith1 and of Burghoff and Bohlen,2 published in 1942, understanding of the problem of the development of ears on deep-drawn brass cups was brought to the point where, from a practical standpoint, producers of brass sheet could keep earing under control. However, these very practical results raised questions concerning the reasons for the observed behavior. Since plastic deformation is fundamentally a function of crystallographic slip, these reasons must be considered in the light of the textures to be found in the annealed sheet. Various attempts have been made. to interpret the mechanism of ear formation by correlation with the preferred orientation and the anisotropy of the sheet. However, none of these has satisfactorily explained why ears are usually found in the rolling and transverse directions for copper but at 45' to these directions for brass. This paper offers additional data on these two related subjects and has been divided into two sections The first section provides a survey of the recrystallization textures of brass as affected by annealing temperatures and prior reductions, and an account of the caring behavior which accompanies these textures. The second section reports new data on the anisotropy that accompanies a characteristic texture for brass and endeavors with partial success to establish the factors that account for the difference in earing behavior between copper and brass Earing BehavioR oF Brass Review of Textures The recrystallization texture of severely rolled brass was first reported by Bass and Glocker.3 The preferred orientation to which this texture, obtained from metal annealed at 500°C., was most akin was (II3)[I12] This texture has been confirmed by Bauer, von Göler and Sachs;4 Brick;' Brick, Martin and Angier;6 and Cook and Richards7 who, in general, used annealing temperatures under 500°C. Bass and Glocker3 also reported the recrystallization texture at 850°C. to be the same as at 500°C. They analyzed their textures by means of single photograms obtained with white radiation. The photo-grams for both temperatures are reproduced in their paper, and there is a strong similarity between the two. However, for the latter temperature, the number of spots registered on the film was remarkably large for the grain size to be expected, and the authors made no mention of using a technique that would integrate a large enough area of the specimen to produce so many spots. The only other attempt to determine textures resulting from high temperature

Jan 1, 1945

By H. G. Doll

A new logging method, called induction logging, is described; it measures the conductivity, or resistivity, of the strata traversed by a bore hole. The apparatus, which is briefly described, comprises a coil system coupled with the ground by induction, so that there is no need for direct contact with the mud, or with the formations. For that reason, the method is particularly useful in oil base mud, and it was first applied to that case. A discussion concerning the respective contribution of each region of ground in the vicinity of the coil system is given. Through the concept of a geometrical factor, it is demonstrated that the total signal, which measures the apparent conductivity, is the summation of the partial products — geometrical factor by conductivity — for the different regions of the ground under consideration. It is thus possible to establish, for each type of coil arangement, investigation characteristic as well as departure curves and correction charts for beds of various thicknesses. This should greatly facilitate the quantative interpretation of the field logs, even in cases where such interpretation would have been difficult on electric logs taken with electrodes. It is also shown that focussing combinations of coils can be used, which give, directly on the recorded log, a value close to the true conductivity, even for fairly thin beds, thus eliminating in most cases the need for corrections. These focussing systems also give a sharper definition of the boundaries between successive strain.

Jan 1, 1949

By H. G. Doll

A new logging method, called induction logging, is described; it measures the conductivity, or resistivity, of the strata traversed by a bore hole. The apparatus, which is briefly described, comprises a coil system coupled with the ground by induction, so that there is no need for direct contact with the mud, or with the formations. For that reason, the method is particularly useful in oil base mud, and it was first applied to that case. A discussion concerning the respective contribution of each region of ground in the vicinity of the coil system is given. Through the concept of a geometrical factor, it is demonstrated that the total signal, which measures the apparent conductivity, is the summation of the partial products — geometrical factor by conductivity — for the different regions of the ground under consideration. It is thus possible to establish, for each type of coil arangement, investigation characteristic as well as departure curves and correction charts for beds of various thicknesses. This should greatly facilitate the quantative interpretation of the field logs, even in cases where such interpretation would have been difficult on electric logs taken with electrodes. It is also shown that focussing combinations of coils can be used, which give, directly on the recorded log, a value close to the true conductivity, even for fairly thin beds, thus eliminating in most cases the need for corrections. These focussing systems also give a sharper definition of the boundaries between successive strain.

Jan 1, 1949

By George K. Burgess, Robert A. Hadfield

1. Introduction.—The methods of production of sound steel ingots have been described in several papers read recently before this Institute. It was thought by Director Stratton, of the U. S. Bureau of Standards, and ourselves to be of sufficient interest and importance, as a further contribution to this subject, to compare the properties of rails rolled in one mill according to American practice, from several types of ingot of substantially the same chemical composition but cast by several processes; and to compare in considerable detail the properties of an ingot manufactured by the Hadfield special-feeding process and one of the usual type for rolling into rails. We are greatly indebted to F. W. Wood, President of the Maryland Steel CO., who made this investigation possible by kindly placing his rail mill at our disposal; and he and his associates at Sparrows Point did everything possible to make the experiment a success, including the execution of several of the tests and analyses. 2. Classification and Manufacture of Ingots.—Of the ingots used in this investigation, eight were made in Sheffield and furnished by Sir Robert Hadfield, and one was made and furnished by an American steel company,l as a comparison ingot, and was supposed to represent the usual type of ingot from which rails are made. The characteristics of the ingots are given in Table I. Ingots 1, 2, 3, and 4 were cast large end up and fed by the Hadfield method in the usual manner with charcoal and blast continued until the molten steel has set on the top of the head, say varying from 20 to 40 min. To ingots 1, 2, and 4 was added 0.1 per cent. aluminum, and to the nickel-chrome ingot, No. 3, 0.125 per cent. For sake of comparison, there were also included two ingots, Nos. 8 and 9, cast with the small end up and fed by

Jan 1, 1915

By W. F., Netzeband

SEVERAL criteria have been used more or less successfully in finding and developing orebodies in this district. Among them is the relation of the fracture to the orebodies. It has been known for some time that there was some relation, but it has been but recently. that careful study has been given to this subject. Like all the criteria used in this district, this relationship must be used with caution, for what-is true in one part of the district is not necessarily true in another.

Jan 1, 1928

By P. L. Russell

The use of nuclear explosives for excavation has been demonstrated to be feasible and practical. Application of nuclear explosives for overburden removal from large ore deposits appears to offer economic advantages over present methods, but under the present pricing schedule, high-yield devices must be used to obtain an economic advantage. The use of nuclear explosives presents problems not inherent in the use of conventional explosives, and thus they can be used only in areas where large explosions and associated phenomena can be tolerated. Stripping of coal with nuclear explosives does not appear practical at this time, but stripping overburden from copper or iron ore deposits may be a potential use. Even here, however, the use of nuclear explosives would require isolation, favorable topography, favorable ground-water conditions, and a low population density. If these basic requirements can be met, the use of nuclear explosives for overburden removal would offer both economic and time advantages. The possibility of using nuclear explosives for peaceful purposes was a subject for speculation as early as 1945. The PLOWSHARE Program was formally established by the AEC in June 1957 for the purpose of developing and demonstrating peaceful applications for nuclear explosives. The technical direction of the program is the responsibility of the Lawrence Radiation Laboratory, Livermore, Calif. Mining and excavation were two fields that received early consideration as areas in which nuclear explosives might be used. Knowledge gained from underground weapons testing increased this possibility, and the development of the thermonuclear device which has a small fission-to-fission ratio, reduced the hazard of radiation, and spurred interest. Nuclear explosives appear to have the greatest potential in the following mining operations: 1.— Surface Mining a) Stripping of waste for open-pit excavation b) Breaking of ore in open-pit mining c) Quarrying d) Blasting for production of aggregate, riprap, etc. 2. — Underground Mining a) Block caving application b) Crushing of ore for in-situ leaching, etc. c) Preparation of underground waste disposal areas Of the potential applications, excavation is perhaps the most obvious and the best understood, and probably the most practical for use in the near future. Large quantities of rock and earth can be moved by proper emplacement of nuclear explosives, but economic and practical relationship must be determined between the known capabilities of nuclear explosives and the required excavating to remove overburden. REMOVING OVERBURDEN IN OPEN-PIT MINING Removing the overburden is one of the largest jobs in open-pit mining. In 1960 open-pit mines produced approximately 130 million tons of coal, 108 million tons of copper ore, and 135 million tons of iron ore. To obtain this much production, an estimated 3-billion tons of overburden were removed from the coal, 216 million tons from the copper ore, and 135 million tons from the iron ore. These figures do not include the initial stripping required before ore production. For example, the ASARCO Mission mine started stripping operations in August 1959 and by mid-November 1961 had removed 46.3 million tons of material including 1.2 million tons of ore.* Initial excavation of this type offers the most favorable conditions for utilizing the earth-moving ability of nuclear explosives. EXPLOSIVE CASTING FOR REMOVING OVERBURDEN The use of explosives to remove overburden is not a new idea. Conventional explosives have been used for this purpose for many years with varying degrees of success. Several small coal strip operators have used this idea to increase production. At these mines about one-third or more of the overburden is thrown by explosives across the pit and onto spoil piles. The additional costs of drilling more blast holes and more explosives are more than compensated for by a reduction in the time required to uncover the coal, and by an increase in coal production.

Jan 1, 1964

By W. L. Fink, L. A. Willey

This paper is the nineteenth of a series from the Aluminum Research Laboratories, presenting the results of the investigations of equilibrium relations in aluminum-base alloys made from electrolytically refined aluminum. In previous papers equilibrium relations have been determined and correlated for 12 binary systems. Equilibrium relations have also been determined for portions of the aluminum corners of three ternary systems (aluminum-iron-silicon, aluminum-magnesium-silicon and aluminum-copper-magnesium). The object of the present paper and those to follow is to increase our knowledge of the aluminum corner of the more important ternary systems. In 1926 Dix and Keith † suggested a new method for designating the phases encountered in alloy systems. The system has been used to a very limited extentl,2,3 The system has since been slightly modified and will be used in this and future papers. In the system as modified, a phase is designated by placing in parentheses the chemical symbols of the elements essential to the formation of that phase. The symbols in the parentheses are separated by dashes in order to clearly distinguish them from a chemical formula. Elements that are not necessary to the formation of the phase in question, but which may be present in solid solution, are not indicated in the designation. If two or more phases would have the same designation according to these rules, they are distinguished by prefixing Greek letters, and are definitely identified by X-ray diffraction patterns. Previous Investigations The solid solubility of magnesium in aluminum has been well established by the work of Dix and Keller4, Schmid and Siebe15, and Saldau and Sergeev6. There is no agreement as to the composition of the magnesium constituents at the aluminum end of the binary aluminum-magnesium system. Hanson and Gayler7 report Mg2Al3; Boyer8 found that the alloy

Jan 1, 1937

By John A. Gann

WITHIN a very few years magnesium has sprung from oblivion, from classification as a technically unknown, little appreciated, and expensive material to front-page importance in many fields of engineering. Bunsen may be considered the real founder of our present magnesium industry. In 1852; he prepared this metal by the electrolysis of fused magnesium chloride in a porcelain crucible. In the following years the electro¬lytic process became recognized as superior to chemical reduction methods and Germany became the world's chief producer, installing the first electrolytic magnesium plant in 1886. ' Thirty years later, national defense requirements, occasioned by the outbreak of the World War and the cutting off of imports, caused France, England, and the United States to begin production. Most of this magnesium was used for military purposes so the close of the war resulted in a large curtailment in production. A few companies, however, encouraged by the early success of the Germans and by the rapid developments taking place in aeronautics, and confident in the certain future and ultimate value of this metal, undertook extensive re¬searches in its production and utilization. A variety of production methods, both chemical and electrochemical, were investigated and some of them operated on a commercial scale. Reduction of the oxide with carbon at high temperatures and the electrolysis of the oxide in a fluoride

Jan 1, 1932

By Dilip K. Das, Douglas T. Pitman

ONE of the major uses of barium in metallic form is as a getter material in vacuum tubes. Because of the high chemical reactivity of the metal, Ba-Al alloys are extensively used. Numerous methods for the preparation of Ba-Al alloys have been published, a few of which1-4 are cited here. Most of these methods were found to be quite elaborate, involving the reduction of BaO, and not too well adapted for the close control of the final composition of small amounts of alloys prepared for laboratory use. A simple laboratory method for the preparation of Ba-A1 alloys in small batches starting from pure metals was devised, so that it was possible to control the desired compositions to within 1 pct. The pertinent features of the alloy system Ba-Al5 are 1) an intermediate compound BaAl, with the melting point of 1050°C, and 2) a eutectic between aluminum and BaAl4 at 98 pct Al. The accompanying sketch shows the experimental arrangement for the preparation of the alloys. Weighed amounts of aluminum and barium were placed in an alumina and a stainless steel crucible, respectively. According to the supplier's specification, the purity of the metals used in the alloys is as follows: a) aluminum rods—99.9 pct Al, and b) barium rods—99.5 pct Ba. The stainless steel crucible, tapered at the bottom and having a 1/16 in. diam hole, rested on top of the alumina crucible. The assembly was placed inside a graphite sleeve which rested on a refractory platform. The platform moved the assembly up and down through the field of a radio frequency coil. A glass bell jar was placed between the crucible assembly and the radio frequency coil to maintain a steady flow of helium around the melt. A small window was cut out on the wall of the alumina crucible to observe the progress of the re- action and to record the temperature with an optical pyrometer. The platform was first raised high enough to move the barium out of the radio frequency coil field in order to allow only the aluminum to melt. The assembly was then lowered so that the barium began to melt and flow out through the small orifice into the molten aluminum. In order to keep the violence of the exothermic reaction under control, the rate of flow of barium was carefully regulated by raising or lowering the crucible assembly. All the samples prepared by this technique were examined by a Norelco X-ray diffractometer using CuKa radiation, The diffraction specimens were prepared by placing the finely powdered samples in flat specimen holders. The Ba-Al alloys prepared with a high barium content were found to consist mainly of BaAl4. The structure of BaAl4 has previously been reported by Alberti and Andress.8 They found that BaAl4 was body-centered-tetragonal with an a0 = b0 = 4.530Å and c0 = 11.14Å. An alloy whose composition was found by chemical analysis to be almost 100 pct BaA1, was used to determine the relative intensities. The d-spacings were obtained from the same alloy to which a small amount of tungsten had been added as a calibrating material. Accurate values for a, and c, were calculated according to the method proposed by Taylor and Floyd.' The calculated values are: a, = b, = 4.566Å and c0 = 11.250Å. The measured d-values for BaAl4 are shown in Table I along with relative peak intensities above background and hkl indices. Acknowledgment The authors are grateful to L. J. Cronin, the head of the Techniques Dept., for suggesting the problem and for his constant interest. References 1Froges and Camargue: German Patent No. 809107, 1951. French Patent No. 935324, 1949. 2E. Bonnier: Annales de physique, 1953, vol. 8, pp. 259-312. 3M. Orman and E. Zemhela: Prac Institute of Metals; 1952, vol. 4, pp. 437-445. 4E. Fujita and H. Yokomizo: Reports Gov. Chemical Industrial Research Institute, Tokyo, 1952, vol. 47, pp. 291-297. 5E. Alberti: Ztsch. fur Metallkunde, 1934, vol. 26, p. 6. 6E Alberti and K. R. Andress: Ztsch. fur Metallkunde, 1935, vol. 27, p. 126. 7 A. Tnslor and R. W. Floyd: Acta Crystallographica, 1950, vol. 3, p. 285.

Jan 1, 1958

By Charles H. Fulton

(Cleveland Meeting, October, 1912.) I. INTRODUCTION. THERE are comparatively few accurate data on the melting-or the freezing-point temperature of metallurgical slays, or on related physical phenomena, such as fluidity near the melting-point, specific heat, latent heat, etc. With the exception of the work of H. 0. Hoffman,1 and some older work by R. Akerman, P. Gredt, and H. M. Howe, no information is available that is of direct interest to the metallurgist. Hofman's valuable work is the only one that refers to slags produced in the metallurgy of copper and lead. The classic work of J. H. L. Vogt,2 who views slays from the standpoint of physical mixtures (solutions in which the entities are minerals), has opened up a. new field in the study of slags, and has placed the investigation of such properties as melting-temperatures, etc., on a rational basis. The recent work of A. L. Day, E. T. Allen, and W. P. White, of the Carnegie Institution, at Washington, and of European investigators 3 on certain systems of silicate minerals confirms the value of the investigation of silicate series from this standpoint, and it is my aim to apply this method to metallurgical slaws, in order to gain exact data of value in metallurgy. The work recorded in the present paper is the result of an investigation of reverberatory-furnace slags made for a Western smelting company to determine exactly the influence of change in composition, within comparatively narrow limits, on the melting-point. For a general discussion concerning the mineralogical character of slaws and the principles on which this investigation is based, reference should be made to other work,4 for the subject is too large to be stated in this paper, except very briefly in the following outline 1 Trans., xxix., 682 (1899). 2 Die Silikatschmelzlösungen; I. Ueber die Mineralbildung in Silikatschmelzlösungen; II Ueber die Schmelzpunkt-Erniedrigung der Silikatschmelzlösungen (Christiania, 1903-04). 3 Doelter, Handbuch der Mlineralehevu:e (1911) 4 C. H. Fulton, Principles (of Metallurgy. Chapter viii., on Slags, p. 24.5 (1910).

Dec 1, 1912

By H. Y. Yancey, B. M. Bird

During the past four years the experimental work in coal washing carried on by the U. S. Bureau of Mines and the University of Washington has been devoted mainly to the development of special methods for the tabling of fine sizes of coals that are difficult to wash. One important outgrowth of this investigation has been the application of hindered-settling classification to coal tabling. Although used for many years in ore dressing, the term "classification" as used here may be new to many readers. It may be defined as the separation obtained when a bed of particles is held in a uniform state of suspension in an upward current of water, either continuous or pulsating, just sufficiently strong to keep the bed in a mobile condition. A common example of this type of separation is a jig in which there is no suction stroke. When the hindered-settling classifier is used with the coal-washing table, the fine-size raw coal, instead of being fed direct to tables, as is the prevailing practice, is first fed to the classifier and grouped, according to the rate of settling against the upward current of water, into perhaps six separate products. After dewatering, each of these except the sixth, a refuse product, is elevated to a seperate feed bin arid washed on a separate table. This paper gives a brief discussion of the basis for the use of hindered-settling classification of a table feed; a description of the experimental work; a comparison of the results obtained with and without classification; and a discussion of the application of the classifier in commercial coal washing. Basis for Use oF Hindered-settling Classification of Table Feed Although theoretical reasoning might be used to justify treating a table feed by hindered-settling classification,l the simplest method of demonstrating the need of such a step before tabling is to show the

Jan 1, 1930

By Chas. B. Dudley

A Discussion of the papers of Mr. James Gayley, on "The Application of the Dry-Air Blast to the Manufacture of Iron," and of Mr. J. E. Johnson, Jr., on "The Physical Action of the Blast-Furnace," by Messrs. Charles B. Dudley, R. W. Raymond, J. E. Johnson, Jr., William F. Mattes, James Gayley, David Baker, John Birkinbine and F. E. Bachman. (Washington Meeting, May, 1905.) CHAS. B. DUDLEY, Altoona, Pa.:-Pam not a blast-furnace man, and this always puts me it a disadvantage because I cannot go into the details of the making of iron and steel. I have not the experience, and have to take the statements of other people, so what I say regarding the subject of this paper is not in the sense of an expert. When I first heard of Mr. Gayley's experiments, I said to myself, " I fear they will result in failure, since, apparently, Mr. Gayley has forgotten one chemical fact, namely, that carbon does not combine with oxygen in the absence of water-vapor." This fact which was so astonishing when it was first brought out some years ago, and which those who are interested may find in the Journal of the Chemical Society of London, for 18S5, page 349, and 1894, page 611, led me to think that the drying of the air would be a mistake. The general subject of the influence of water-vapor on chemical action is a large one; but the special point in which we are for the moment interested, namely, the influence of water-vapor on the combustion of carbon, was especially treated by Mr. H. B. Baker, in the papers referred to. Apparently, however, as the result of Mr. Gayley's experiments, we are to learn that the amount of moisture still left in the desiccated air is sufficient to secure perfectly satis¬factory combustion. In thinking over Mr. Gayley's paper, it occurred to me that there were two alternatives, either of which might be chosen, namely, we might dry the air as Mr. Gayley does, or possibly we might, in a very much simpler way, simply saturate the air at a constant temperature, and thus get uniform working and

Sep 1, 1905

F. E. Bachman, Port Henry, N. T. (communication to the Secretary*):—In discussing Mr. o.o.Laudig's paper, the Action of Blast-Furnace Gases Upon Various Iron-Ores,' I took the ground that Mesabi-ore explosions were entirely mechanical; but more observation and later experience has caused me to

Jan 1, 1905

By F. C. Stanford

The work of an engineer is to direct natural forces so that the: bring about the results that he wishes to secure. Heretofore he ha concerned himself chiefly with physical forces and inanimate objects until he has secured a truly marvelous degree of control over them The great problem of the present age is to secure a like degree of know1 edge and control of the human factor. Progress has already been made along this line, but it is only a beginning. Wilhelm Ostwald says tha scientific knowledge enables a man to be a true prophet; but it must be remembered that a good many people do not seem to be able to main tain a high average in prophecy. In short, 'the average of knowledge is not equal to the average needs of the present time, but continually fails to keep pace with it. It has been aptly said that the really essentia need of the period is for more brains; if we only had sufficient knowledg and sagacity we could not only solve all difficulties, but prevent then from arising. This generalization holds good for an industrial organization. Th most vital need of the management is for more brains. The logica course for an engineer in charge of an industrial organization is, therefore to direct whatever forces may be at his command toward the development training, and guiding of all the brains in his organization. This is easie said than done, for it involves the carrying on toward two objective: the maximum of productive work, and the development of the individual who perform it. This is essentially like the rebuilding and enlarging of plant, keeping it in full operation the while. On the other hand, if th aim is merely for maximum production from an organization, withou offering opportunity for development, the final outcome will necessari be like that of a plant that is driven at full capacity without stoppin for repairs or improvements; it eventually becomes so run down th either a complete rebuilding is necessary or else it has to be abandone

Jan 1, 1918