Search Documents

By D. Goossens

Quality control is a system which should guarantee that quality is achieved. It is the execution and verification of a project in an organised way, in order to obtain the maximum of certainty that the results meet the requirements. This concerns all stages of the project, from the soil investigation, over the design, to the execution. Quality control can and has been successfully realised for important projects by means of a quality plan. A quality plan is based on a number of general considerations, but should certainly be focussed on the particularities of a specific project. Practical examples of quality plans, which have been realised on sites in Belgium, are developed and the advantage of the system is shown by concrete case studies.

Jan 1, 1996

Jan 1, 1970

By Bernard Baum

Combined preservative/fire retardant systems were pressure impregnated into Douglas fir and Ponderosa pine samples and evaluated for decay, flammability, and mechanical properties. The objective of the evaluation was to identify cost-effective systems for use with mine timber, and to provide an information and data base from which Federal code regulations could be established. Thirty systems, based on combinations of commercially available preservatives and fire retardant impregnants and coatings, were applied to Douglas fir samples and evaluated for decay and flammability. The ten most promising systems were ap¬plied to both fir and pine and reevaluated for decay and flammability before and after water leaching. The five best systems were given a thorough laboratory evaluation using both pine and fir. Evaluations included flame spread, smoke density, toxic gases, decay, compressive strength, flammability after artificial weathering, and cost. All systems had acceptable toxic gas levels and smoke densities, but flame spread was only borderline acceptable for most of the samples tested. A trade-off analysis showed Acid Copper Chromate/Fyrprufe with Albi-107A/144 intumescent paint and Koppers NCX to be the-best systems. Recommendations are made for further large-scale testing using the two best Systems.

Jan 1, 1978

By P Fullagar

Automated multi-sensor core loggers (MSCL) measure petrophysical properties of diamond drill cores, including gamma density, P-wave velocity, electrical conductivity and magnetic susceptibility. A Geotek MSCL system has been used to record petrophysical data on archival drill core from Cadia East Au-Cu porphyry deposit, New South Wales, Australia, for correlation with metallurgical parameters. P-wave modulus, calculated from density and P-wave velocity, exhibits a correlation with small-scale crushability (A*b) test results, and hence offers a means for æcontinuousÆ characterisation of ore crushability at Cadia East. Magnetic susceptibility has proved to be a good indicator of alteration styles, and is a possible indicator of crushability.

Jan 1, 2009

By Thomas Leonard Watson

Jan 1, 1906

By J. Torma-Krajewski, M. Lehman

In 2005, NIOSH and Badger Mining Corporation entered a partnership to implement ergonomic interventions, including a systematic process, to address exposures to risk factors that may result in musculoskeletal disorders or other types of injuries/illnesses. As a result of this partnership, an ergonomics process was integrated with the existing safety and health program to promote an on-going application of ergonomic principles, and over 40 task-specific interventions were implemented during the first year of the process. This paper presents details of the process integration, and several examples of task-specific interventions that reduced exposures to risk factors.

Jan 1, 2007

By W. K. Gowans

The Sullivan Concentrator treats a complex sulphide ore consisting mainly of galena, marmatite and pyrrhotite. The ore carried minor values in silver, antimony, bismuth, indium and tin. The products of the concentrator are lead, zinc, iron and tin concentrates. The minor metal values other than tin are recovered from the concentrates by the refining processes in the smelter at Trail.The concentrator was completed in 1923 and first operated with a capacity of 2,500 tons per day. In the years 1926 to 1929 changes to equipment and buildings brought the operation up to 5,500 tons per day and then, in the years 1935 to 1945, the daily tonnage was raised to 8,500 tons. After 1945, the rising insoluble content of the ore made it necessary to consider the construction of a Sink-Float plant. At this time consideration was also given to the construction of a new crushing plant underground to replace the rolls crushers and cone crushers located at the concentrator. By 1949, construction of the Sink-Float plant was completed along with a new underground crushing plant, and an electric haulage way between the underground crushing chamber and the Sink-Float plant. The ore was hauled in forty 14-ton car trains which discharged into a 3,000 ton receiving bin by means of an air operated five car rotary dumper. With the start up of the,Sink-Float plant, a 1 ½ ft. by 12 ft. Hardinge rod mill was also brought into operation. The Sink-Float plant made it possible to treat 12,000 tons/day of mine run ore with up to 40% of this being rejected as float.

Jan 1, 1975

By Patrick O. Shires, Harry W. Schnabel

With stable building sites becoming scarce in the greater San Francisco Bay Area, the new Summit Senior Care Facility is being built into the side of an unstable hillside adjacent to the San Ramon Regional Medical Center in San Ramon, California. This hillside has had a long history of instability and the site of the new Senior Care Facility required excavation into both a historic old landslide and a more recent active landslide. After a thorough geotechnical study, it was concluded that the best way to build the new facility would be to construct a tied-back retaining wall in the area of the old landslide, since it extended off-site onto two adjacent properties, and remove the active landslide and replace it with compacted fill before cutting into its toe area with an additional tied-back retaining wall. The design was further complicated by the proximity of the site to several active faults. In the area of the old landslide, the combination of an ascending slope behind the wall, landslide forces and seismic forces resulted in total design pressures between 365 to 4,575 PSF for a wall with a maximum height of 30 feet. The wall for the old landslide was constructed by first drilling and placing steel soldier piles in concrete. The tip of the soldier piles extended a minimum of 12 feet below the landslide plane that was up to 36 feet below the bottom of the wall. Permanent double corrosion protected tiebacks were then installed through the soldier beams and anchored below the slide plane. A shotcrete facing was then installed on the face of the wall. BACKGROUND The site of the Summit Senior Care Facility is located on the southwest flank of Mount Diablo adjacent to San Ramon Valley which is characterized by gently rolling hills. The San Ramon Valley Regional Medical Center, which opened in 1990, is located to the north and an existing church is located to the southwest. There are also private residences located to the southeast. The site is shown in Figure 1. Numerous faults run close to the site, the most significant of which are the Calaveras and Pleasanton faults. The site has also had a long history of slope instability and has been the subject of numerous investigations. Studies conducted in 1979 and 1984 concluded that there was a landslide in the area and recommended that a buttress shear key be constructed between the subject site and the existing church for a sewer main as well as removal and replacement of the head area of the old landslide to stabilize the hospital site. While two previous geotechnical studies in 2008 and 2016 identified slope instability, they did not recognize the genesis and limits of the old landslide on the western portion of the site or the limits of the active landslide on the eastern portion of the site.

Jan 1, 2018

By Stan Henning

The monthly summary of the climatological record for the demonstration mine is presented in Table 1. Tear normal temperatures occurred throughout the growing season. From May to October precipitation was more than normal except in June when it was 2.55 inches below normal. Corn and soybean plantings were delayed until June 2-7 because of wet field conditions. This is about one month later than normal for corn planting. Insect infestations were much less than those encountered in previous years. Cutworm activity was not noticed and alfalfa weevil infestation were small and patchy. Stalk rot in corn was a significant problem at harvest and resulted in much Milk lodging. The wet and generally overcast conditions of July, August and September were bend 10 beneficial al to certain plant disease organisms. For example, pumpkins planted in a small garden area at the demonstration mine did not ripen because of a powdery mildew resulting from overcast, wet conditions. Field operations and row crop plantings were greatly delayed by wet field conditions. It was difficult to plant by conventional tillage because the soil remained soft and sticky where the moldboard plow had been used. Plots in the no-tillage system could he planted before conventionally tilled plots could be traversed. Plant emergence and plant density at

Jan 1, 1982

The Skorpion process comprises three processing steps, atmospheric leaching in sulphuric acid, zinc solvent extraction and electrowinning to produce special high grade zinc. The major mode of impurity transfer was attributed to crud runs in the solvent extraction circuit. Crud may be described as a heterogeneous, partly inorganic, partly organic mass of material which accumulates predominantly at the interface between organic and aqueous solutions. The paper describes the route causes of the crud formation in the solvent extraction circuit and optimisation strategies which are being followed to prevent impurity excursions in electrowinning. Keywords: zinc oxide, solvent extraction, crud formation, colloidal silica

Jan 1, 2007

By E. J. Gleim

The importance of "good voltage," especially for direct-current systems in coal mines, is not always fully appreciated. From the practical aspect there are three viewpoints from which low voltage may be considered, namely: (a) its effect upon operation of electrical equipment, (b) its effect upon cost of maintenance and power, and (c) its effect upon safety in the mine. The design of electrical motor-driven equipment usually is based upon a given or assumed constant value for the voltage of the system; consequently, when there is an appreciable drop below this value, unsatisfactory operation is likely to follow. In the case of shaker conveyors, for example, one manufacturer has pointed out that these conveyors must be operated at a certain definite speed if maximum output is to be secured. As shunt motors are used in the conveyor drives, either a rise or fall in voltage will produce corresponding changes in speed and thus seriously affect the efficiency of the conveyor. The introduction of automatic control for mine equipment has been greatly retarded because the relays, contactors, and other special devices required have failed to function properly when attempt was made to operate them on systems subject to variable and low-voltage conditions.

Jan 1, 1937

"In mining operations, it is widely accepted that strategies to drive operational goals must revolve around improving plant availability, reliability and process efficiency. In this paper, an integrated solution framework for reducing process variability, increasing process efficiencies and maximizing plant availability and reliability is discussed within the context of a typical milling circuit. The framework exploits a real-time analysis “gap” evident in production operations that prevents timeous identification of equipment and process failures. This is achieved by leveraging predictive analytics for equipment health monitoring, control loop monitoring and advanced regulatory control solutions towards enhanced process performance, improved asset management and regulatory compliance. The framework provides for early and actionable warnings on equipment and process degradation using real-time operational data.INTRODUCTION The changing landscape of gold mining and processing presents many challenges that threaten sustainability of existing (marginal) operations as well as deter investment in new projects. As existing “shallow” ore resources become depleted, mining operations are increasingly treating low-grade ores with complex and randomly variable mineralogical characteristics. For example, in South Africa, historically one of the major gold producers, the average grade of ore treated has been decreasing from averages above 4.5 – 5 g/t to current grades averaging less than 3 g/t within a decade (Chamber of Mines, 2012). Moreover, lower tonnages are being treated as a result of the narrowing of the available resource base. Also, the regulatory framework has tightened over the years due to heightened concerns on the safety, health and environmental impacts of mining and related activities."

Jan 1, 2014

By E. A. Mihok

A pilot plant for treating mine drainage by neutralization with limestone was designed, fabricated, and operated by the Bureau of Mines. The process consists of (1) producing a very fine (minus 400-mesh) limestone slurry, (2) mixing the slurry with the mine water, (3) aerating the resulting mixture to remove carbon dioxide and precipitate iron, and (4) separating the solids from the liquid by sedimentation. A mine discharge of pH 2.8, containing 1,700 ppm total acidity, 36 ppm ferrous iron, and 360 ppm total iron, was treated at rates from 300 to 400 gpm. The treated water ultimately reached a pH of 7.4 and contained no detectable iron. The resulting sludge compacted to approximately one-third the volume of sludge from mine water neutralized with lime. The advantages of the limestone process, compared with the conventional lime process are as follows: Widespread distribution and lower cost of run-of-mine, indigenous limestone; simplicity of plant design; reduced hazards and plant operating and maintenance costs accruing from the use of a less reactive chemical agent; higher solids concentration of the precipitated sludge; and no deleterious effect caused by accidental overtreatment. While total process costs could not be determined, it is conservatively estimated that the cost of treating mine water by the limestone process is one-third to one-half the cost of the lime process, depending on the characteristics of the water to be treated and the availability and quality of limestone used.

Jan 1, 1968

By M. Zanotto

[ ] A period of heavy rains caused the river Adda to flood parts of the Valtellina, one of the Alpine valleys of Northern Italy. The exceptionally high waters put under considerable strain the whole system of embankments and levees controlling the river and protecting the adjacent towns and lands. In some places the water breached and washed away the embankments, submerging large tracts of cultivated land, buildings, roads and railway tracks. The town of Talamona, in the lower Valtellina, was hit particularly hard: in its proximity the river overrun and then washed away 300 m (1,000 ft) of embankment (see vicinity map, fig. 2), depositing large amounts of riverbed debris onto over 400 hectares (1,000 acres) of fertile land.

Jan 1, 1992

By Robert S. Hill

"In November 1942, a preliminary report on the Swartz Mining District by John H. Soule, an engineer of the Bureau of Mines, recommended an exploratory program of diamond drilling. The existence of zinc and lead deposits in this region had been known for many years. In 1943 and 1944, the Federal Geological Survey made a detailed study of the same area. Later work done by the Bureau of Mines in this district followed the suggestions made by these geologists.3/In the latter part of 1944, Felix A. Vogel, Jr., another Bureau engineer, made a study of the Grey Eagle mine in the Kingston Mining District, a few miles northeast of the Swartz district, and his recommendations for diamond drilling were followed in so far as funds permitted. Drilling was started in October 1943 and was completed in June 1945.4/In its program of exploration of Mineral deposits, the .Bureau of Mines 'Ms as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution t national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, R. G. Knickerbocker, chief, analyzes samples of ore and performs beneficiation tests. Both these branches are under the supervision of Dr. R. S. Dean, assistant director.With respect to this report, special acknowledgment for assistance is due to C. H. Johnson, chief of the Rolla Division, Mining Branch, and to various members of the Geological Survey."

Sep 1, 1946

The history of the industry which recovers rutile and zircon from the heavy mineral beach sand deposits of Eastern Australia began with the initial discovery of zircon in 1895. Whereas a large number of small companies operated during the rutile boom of 1955-57, the industry is now controlled by a few large groups.Mining is mainly by suction dredging. Metallurgical practice is a two-stage process in which a bulk concentrate of heavy minerals, recovered by gravity methods, is separated into its constituent minerals by processes based mainly on surface, electrical, and magnetic properties.Various separating devices using these principles have been developed in the industry and combined in various ways in the operating plants.There is scope for future metallurgical developments.INTRODUCTIONThe existence of deposits of heavy minerals ("black sands") on the northern coast of New South Wales has been known for at least 90 years. The earliest metallurgical operations aimed at the recovery of gold, platinum, tin and monazite. Mainly because of the low grade of these deposits with respect to these minerals, but also due to metallurgical difficulties, such operations were abandoned by about 1895 (Whitworth, 1959). The presence of zircon was recorded quite early (Carne, 1895) but Raggatt (1925) appears to have been the first to report the presence of rutile.The economic exploitation of the deposits was initiated in 1928 when D. H. Newland, State Geologist of New York, made an examination on behalf of The Titanium Alloy Manufacturing Company of America. Developments were then delayed by the world-wide depression, and the first commercial separation of the heavy minerals was made at Byron Bay in 1934 by Zircon Rutile Ltd. using a froth...

Jan 1, 1963

By M. Jacobs

Keywords: Smelting, converting, sulphide, sulphide smelting, platinum, platinum group metals, PGM, base metals, nickel, copper, matte, slag, furnace, electric furnace, Söderberg, electrode, granulation, converter, flash drier, sulphuric acid, acid plant, Ausmelt, Sirosmelt, pyrometallurgy, metallurgy, Anglo Platinum, South Africa Waterval Smelter complex is situated in Rustenburg, in South Africa?s North West Province. The smelter objective is to process wet concentrate to produce crushed, slow-cooled, sulphur-deficient nickel-copper matte rich in platinum group metals (PGMs), gold, and base metals for despatch to the Magnetic Concentration Plant at the Base Metals Refinery. Throughout its history, the smelter complex has been continuously upgraded in line with increasing production demand, changing feeds, environmental initiatives, and advances in available technology. The smelter receives filter cake and slurry from Anglo Platinum concentrators and joint ventures. Wet concentrate is fed through a flash drying process utilising coal-fired, fluidised bed hot-gas generators, to produce dry feed material for the electric furnaces and slag-cleaning furnace. For primary smelting, two electric furnaces are used, each with a rated capacity of 34MW. Furnace matte, containing the bulk of the base metal sulphides and PGMs, is tapped periodically into refractory-lined ladles and granulated using high-pressure water jets, then dried through electrically powered pneumo-driers to become the main feed to the Anglo platinum Converting Process (ACP). Slag is tapped semi-continuously, granulated, and treated through the slag mill. The ACP treats the combined matte output of Waterval, Polokwane, and Mortimer smelters. It is a top-blown furnace, with furnace matte, air, and oxygen being injected into the converter via a lance submerged in the slag. Converter matte is tapped and bottom cast into moulds, slow-cooled, crushed, and despatched to the refineries. Slag is granulated and dried for recycling to the slag-cleaning furnace. ACP slag is fed to the slag-cleaning furnace along with a reductant and a sulphur source. Slag-cleaning-furnace matte is granulated for processing by the ACP, while slag is granulated and processed in the slag mill. The slag mill and flotation circuit treats granulated slag from the electric furnaces and slag-cleaning furnace to recover entrained matte containing valuable PGMs and base metal sulphides.

Jan 1, 2006

By J. F. Reddick

The South African coal mining industry is currently disposing of about 10 million tons of ultra-fine coal (<150 µm) per year. Once discarded, these sulphur-containing ultra-fines contribute to several environmental problems. As part of a project initiated by the Water Research Commission to investigate the use of Cleaner Production (CP) in the mining industry, a study was carried out to determine whether a CP approach could be used to identify opportunities to reduce this coal waste, and to determine which of these opportunities would be most feasible. In order to do this, a CP assessment was conducted at three case study collieries in the South African Witbank coalfield. Mass-balancing and sampling, followed by laboratory characterisation tests and site surveys, were used to determine the quantity, quality and sources of the ultra-fine coal at the three collieries. Literature reviews, brainstorming sessions and interviews then followed to generate the CP options. An environ-mental, economic and technical feasibility assessment was then prepared for each option, to determine the most viable interventions for implementation. A number of opportunities were identified through the assessment. By preventing coarser coal from being discarded with the ultra-fine coal, the quantity of coal disposed of could be decreased at all three collieries, and by up to 24% in one case. Increasing the crusher top size would reduce the amount of coal that is milled to less than 150 µm, so that less is wasted. The ultra-fines that have already been disposed of on slurry dams can be completely reclaimed and converted into a valuable product, which can be sold as power station feedstock. The newly processed ultra-fines could be beneficiated using flotation and exported together with the coarser coal. The results of the assessments thus suggested that workable CP opportunities to reduce ultra-fine coal wastage exist at the sites investigated, and that their feasibility is colliery-specific. The associated financial benefits of the proposed options suggested that CP is a realistic approach to addressing environmental problems. Keywords: Cleaner Production; coal mining; coal-washing; ultra-fines

Jan 1, 2007

By G. Major-Marothy

"INTRODUCTIONA beneficiation plant to upgrade earthy iron ores is being installed by the Iron Ore Company of Canada in Sept-Iles, Quebec.The crude ore for the plant will come from the Knob Lake area, located in Northern Quebec, where mining has been in progress since 1954.Some 170 million tons of ""direct 11 ores have been mined and shipped in the past eighteen years, with an overall silica content of 7 to 8 percent. No beneficiation - except the reduction of the top size to about 2 inches - took place during this period, but extensive research work has been carried out, in order to find a feasible process.Since “washing"", gravity separation, roasting and magnetic separation experiments did not indicate positive enough results, flotation was tried and found to be feasible.The beneficiation complex being installed will consist of grinding, flotation, dewatering - i.e.: thickening, filtering and drying - balling feed preparation, and agglomeration - i.e.: balling and induration.This process will result in a product superior to the ""direct shipping"" ores and will also expand the ore reserves by allowing material with a higher silica content to be utilized.THE OREThe Knob Lake ores are grouped by mineralogical composition and by grade.BLUE ORES, representing roughly two thirds of the reserves, carry their iron content mostly in the form of massive, blue hematite and martite.YELLOW ORES, about one sixth of the reserves, have predominantly hydrated iron oxides as the iron bearing minerals.RED ORES, the other sixth of the reserves, carry the iron mostly in the form of red hematite.The gangue in all ores is mainly quartz, but aluminum oxides and hydroxides are also present, particularly in the red ores."

Jan 1, 1972

By E. R. Maize

This report is the third of a series on convergence of roof and floor in coal mines and subsidence of surface that accompanies it. The first papery dealt with extraction in a mechanized mine (Montour 10) having relatively short rib lines that retreat rapidly. The second 6/ dealt with extraction in a mine (Crucible) in which coal was loaded by hand and in which the rib lines were long and slow-moving. The present report deals with a mine (Gibson) in which conditions approximated those in the Crucible mine, except that the distance between room centers was considerably less and the pillars were narrower in consequence. Moreover, the average cover was less and the studies were made under the steep hillside of a stream valley compared with a gently rolling surface over the portions of the second mine studied. Gibson mine lies in the east-central part of Washington County, Pa., approximately midway between the Montour 10 and Crucible mines on a north-south line. A cooperative agreement covering the work was made with the Hillman Coal & Coke Co. through W. L. Affelder, vice president. This paper describes the methods used in the investigation, gives excerpts from the data obtained, and offers such generalisations as appear to be justified.

Jan 1, 1940