Search Documents

By T. van Heerden

A range of supported gold catalysts was prepared by ion exchange, varying many of the preparation variables, including concentration in the precursor solution, washing procedure, as well as drying and calcination procedures. These catalysts have been characterized extensively. TEM images show essentially the same crystallite size distributions, between 2?5 nm, for almost all catalysts, the only exception being catalysts not washed in ammonia, which did not show any small crystallites. Additional characterization with SEM yielded an interesting discovery. Catalysts that appear identical on the TEM also contain some large crystallites in the range of 50?500 nm. Differences in dispersion due to the drying procedure not seen on the TEM can now be observed. Oxygen chemisorption is being investigated as an additional method to characterize gold based catalysts to complement the typically used electron microscope techniques.

Jan 1, 2012

By D. E. Larson

The U.S. Bureau of Mines investigated Fe-base alloys containing 8 pet Crwith Ni, AI, and Si additions as substitutes for standard AISI Type 304 stainless steel (SS) in high-temperature oxidizing applications. The objective of this study was to reduce the amount of Cr required to make an austenitic stainless steel while retaining satisfactory workability, mechanical properties, and oxidation resistance. Alloys prepared in this investigation had a composition of Fe-8Cr-lMn-0.07C with varying amounts of Ni, AI, and Si. A minimum of 10 pet Ni was required to achieve an austenitic composition. The microstructures of the austenitic alloys were very susceptible to room-temperature, deformation-induced martensitic transformations. When the alloys were cold worked or stressed, the materials had far greater tensile strengths than Type 304 SS at room temperature. At higher temperatures, tensile strengths and workability of several of the alloys were comparable to that of Type 304 SS. Although martensitic transformation caused the room-temperature properties of the experimental alloys to be quite different than those of Type 304 SS, the superior oxidation resistance and similar hot workability of several alloys encourage their use as replacements for Type 304 SS.

Jan 1, 1989

By Franklin D. Cooper

The value of nonfuel raw mineral production in the United States for 1977 increased over that of 1976 by 5%, from $16.7 billion to $17.5 billion. Metals declined by 5% from $6.1 billion to $5.8 billion, chiefly because of strikes in the iron ore industry and a depressed copper market. Subsidization of mining industries in some foreign countries accounted in part for the excess of copper and some other metals on world markets. Weak metal markets and continued slowdowns in the world economy were the main reasons of the virtual absence of new mine projects. Increasing domestic governmental involvement affecting mineral industry activities, such as pricing controls, public land withdrawals, and the Surface Mining Control and Reclamation Act, effective August 3, continued to be controversial and to be criticized by various segments of the industry.

Jan 1, 1980

By James W. Pennington

MERCURY, also widely known as quicksilver, ranks tenth in quantity in world output of nonferrous metals. However, its unusual and desirable combination of properties- liquid liquidity at ordinary temperatures, high density, uniform volume expansion, electrical conductivity, ability to alloy readily, high surface tension, chemical stability, and toxicity of its compounds -gives mercury an industrial and military importance out of proportion to the small physical size of the production industry. Although mercury has been known and used for over 20 centuries, until the 16th century consumption was small and chiefly in medicine. Since then mercury's applications have paralleled scientific advancements, kind current principal uses of mercury are in electrical apparatus, industrial and control instruments, agriculture, pharmaceuticals, and the electrolytic prepa¬ration of chlorine and caustic soda. Other materials may be substituted for mercury in come applications; yet, for those uses that require mercury's unusual combination of physical and chemical properties, there is no ideal substitute.

Jan 1, 1959

By D Craw, J Becker

Post-metamorphic structural evolution of Otago Schist resulted in a pattern of northwest and northeast striking faults and fractures cutting the basement rocks. These faults have been reactivated several times since Mesozoic metamorphism. Gold-bearing quartz veins which have been exploited sporadically over the past 130 years are almost invariably hosted by northwest striking structures, and most exploration has been focussed on these structures. There is evidence for hydrothermal activity and mineralisation along some of the northeast striking structures, although there has been very little work done on these structures. Our study is attempting to characterise the hydrothermal processes in the northeast structures, in comparison to the northwest structures, in order to see if further detailed exploration is warranted. There is evidence for both normal and reverse senses of movement on northeast striking faults, and some of the faults have evidence for early ductile deformation overprinted by later brittle structures. Northeast striking structures host stibnite mineralisation in places, and faults are locally silicified or extensively impregnated with ankeritic carbonate. Sulphides are rare in veins, but do occur in some hydrothermally altered host rocks. Hydrothermal haematite accompanies extensive silicification along the Manuherikia fault zone near Alexandra. Anomalous gold concentrations occur in some hydrothennal zones, and in downslope sediments in some localities.

Jan 1, 1998

By Thomas A. Phillips

The Bureau of Mines presents an economic evaluation of its leach- electrolysis process for recovering lead from galena concentrate. In this process, galena concentrate is leached at 200° F with a ferric chloride-brine solution to extract lead while leaving sulfur in the residue, which is discarded. The solution after leaching is concentrated and cooled to 100° F by vacuum evaporation to crystallize lead chloride from which metallic lead and chlorine are produced by fused-salt electrolysis. Chlorine is used to regenerate the spent leach solution before it is recycled. A cost estimate was prepared for a plant capable of producing 300 tons per day of lead, 330 days per year. The fixed capital cost on a third-quarter 1977 basis Fs $27,500,000, and the estimated operating cost without a charge for the concentrate is 4.9 cents per pound of lead product. Assuming a selling price for corroding-grade lead of 31 cents per pound and a charge for the concentrate of $332 per ton, the interest rate of return on investment after taxes is 16 percent. The leach-electrolysis process, therefore, appears to be economically attractive under the assumed market conditions.

Jan 1, 1978

By Andrey V. Tarasov

To carry out a physicochemical substantiation of a transition to ?soft? modes of reduction of calcine obtained by desulfurizing roasting of nickel concentrate produced as a result of copper-nickel converter matte separation in a nickel anode production circuit, an analysis has been conducted of the macrokinetic behavior of actual calcine samples in the presence of gaseous H2-CO mixtures and solid reductant additives. Within a temperature range of 900°C to 1100°C the main regularities typical of the calcine reduction process with individual gases (H2, CO) also take place when using a gaseous mixture. Under the conditions of low-temperature (900°C to 1000°C) nickel oxide reduction with products of fuel oil conversion in the presence of coke, the role of the latter is insignificant from the technological viewpoint. As a result of the present investigations, we have obtained analytical expressions of macrokinetic parameters of the reaction interaction within the [NiO] calcine-H2-CO-C-CO2-H2O-O2-N2 system.

Jan 1, 2005

By Akira Yazawa, Alžbeta Gubcova

RECENT lead-smelting techniques have tended toward use of high-grade concentrates with minimum amounts of flu, accompanied by profitable employment of roast reaction.1-5 In order to better understand these smelting processes, thermodynamical calculations have been carried out on the Pb-S-0 system, and the results obtained have been presented in isothermal reaction diagrams in which log Ps, and logPo, were the axes. The diagram thus constructed seems to be more convenient to grasp the equilibrium aspect than those published hitherto.6-8

Jan 1, 1968

By J. R. Cole-Baker

An independent technical audit by a consultant is part of the accountability process of publicly owned or publicly quoted companies when raising finance through share issues or loans or the sale of equity, and of banks or development funds when granting loans. Africa is undergoing a renaissance in investment in its mining industry. It is forecast that capital investment, in major mining projects in Africa, will be over US$ 4.4 billion, in the next few years. Most, if not all, of the capital to be raised will require an independent technical audit. The aim of this paper is to assist the management of mining companies seeking finance in appreciating the role of such technical audits. The reasons for such audits, especially to attract international investment, are listed. The role of the audit is explained in assessing the underlying robustness of the company as ?a going concern? and the viability of any ?expansion plans?. Its use is emphasised in establishing the underlying value of the company based on the mine life as supported by the mineral reserves. The independent consultant role is stressed as a representative of the parties in a finance deal who cannot, in practice, carry out their own detailed and specialized technical due diligence. The various components of a typical audit are examined with examples of critical matters which may require resolution. The definitions, which are used commonly in audits, in respect of competence and reserves and resources, as stated by various regulatory bodies, are compared.

Jan 1, 1998

By J. C. Fowler

The field testing of the Seismic Mine Monitor System is described. This system consists of nine geophones buried about 40 feet deep over a ten-square-mile area, the amplifiers and electronics needed to get the signals to the mine office, and a central processor unit to detect and locate explosions and large roof falls. Since the problems associated with the original installation were solved, this system has worked for 2 1/2 months. The system has detected roof falls in the pillar areas and has located blasts as small as 114 pound of dynamite. The location accuracy has, in general, been within 250 feet. The system is now being used to gather long-term data on the seismic activity of the mine.

Jan 1, 1974

By Walter D. Holland

This is one of a series of instruction guides developed to help instructors present health and safety training courses to workers in the metal and nonmetal mining industry. This course is intended for training those, usually the safety officers, who perform surveys for inhalation contaminants in above ground work areas. The handbook entitled ?Handbook for Surveys of Inhalation Contaminants in Above Ground Metal and Nonmetal Mining and Processing Work Areas? is used as a manual for the course and as a prime reference when performing the actual surveys or interpreting the sampling results. There are six experiments for the students to perform during the course to familiarize them with the sampling devices routinely used during the surveys.

Jan 1, 2011

By Roger A. Archabal, Omar A. Conte, Gustavo Langoni

This international case study focuses on the rigorous geotechnical interaction and results of a soil improvement program utilized to mitigate consolidation settlements of over 1.5 m [5.0 ft]. The extreme settlement results from very deep, nearly normally consolidated clay and the required high floor loading of a new Logistics Park near Bogota, Colombia. The general subsurface conditions consist of very soft clay extending to depths beyond the 50 m [164.0 ft] explored. A required 1.2 m [3.9 ft] thick fill combined with high floor loads resulted in an applied areal load of approximately 7 ton/m2 [1300 psf] (equivalent to about 4.5m [15.0 ft] of fill). Langan recommended performing a test section to validate the initial consolidation settlement calculations and evaluate possible optimization of the prefabricated vertical drain (PVD) spacing and length. The test section sizing was designed to accurately represent the stresses at depth of the future structures. Extreme settlements of over 1.5 m [5.0 ft] in the center and large differential settlements of over 0.6 m [2.0 ft] were measured between the center and corners of the test section over a relatively short test time. Discussion on the methodology, instrumentation, measured results and future optimization are presented. The recommended soil improvement varied from the standard approaches typically utilized in the area. PROJECT LOCATION AND DESCRIPTION The project site is immediately north-northwest of the city of Bogota in the Bogota Valley. The site is bordered with, and has historically been, farming land bordered to the south by the El Rosal-Bogotá highway. The overall site encompasses about 570,000 m2 [141.0 acres] of gross area and about 484,000 m2 [119.6 acres] of net buildable area. The warehouse complex will consist of 10 very large warehouses with footprints ranging from about 15,000 m2 [3.7 acres] to 30,000 m2 [7.4 acres]. The total building area is about 210,000 m2 [51.9 acres] with most of the remaining areas being paved principal drives, truck parking or administrative parking. The topography of the site is relatively flat and close to final grade in roadway areas. However, the warehouse floors will be raised about 1.2 m [3.9 ft] (equivalent to about 2 t/m2 [370 psf] considering engineered fill) to allow for truck docking. In addition, the design floor loads are heavy and estimated to be up to 5 t/m2 [930 psf] and equivalent to about 2.5m [8.2 ft] of fill. Geotechnical conditions at the site are very weak at depths of 50 meters [165 ft] or more, with soft compressible clays comprising the majority of the soil profile. The Bogota Valley is composed in some areas of very deep alluvial deposits. These deposits have been classified as an important challenge and limitation to the development of high/heavy structures such as the project in question for many years (Orozco, 2006). Soft clay deposits have been encountered even beyond depths of 100 meters [328 ft] in some regions of the Bogota Valley (Sanz, 1994). Extreme settlements can be expected if extensive and high permanent loads (above preconsolidation stress levels) are supported in these thick alluvial deposits.

Jan 1, 2018

By S. G. Beattie, N. Mojtabai

A study was carried out which aimed to: determine the effects of blasting on excavation perimeters and nearby slopes; establish a low-cost blast monitoring and field observation programme to determine peak particle velocities and blast damage; and to develop criteria for observable blast damage that are based on the peak particle velocity. Full-scale production blasts in a large open pit copper mine were monitored and studied to develop damage criteria for various rock types. Better blast designs can be achieved by correlating the results of blast monitoring with field observations of damage at the pit walls and on benches. Back-break and damage are related to blast-induced ground vibration. Peak particle velocity is accepted as a reliable measure for the prediction of ground vibration levels. Empirical models for the estimation of rock damage can be developed and used for blast design. The models are used to determine the zones of damage within the rock face. Rock damage models can also be used to design trim shots to achieve further reduction of back-break in more critical areas

Apr 1, 1996

By Michael Alber

Resin grouted rock bolts are the major support measure in coal mining. They are rather easy and foolproof to install, take immediately load and are the least time consuming support measure for controlling gateroad deformation. The use of only resin grouted bolts allows fast gateroad development which is essential for economical resource exploitation. The design of reinforcement / support systems for coal mining typically bases on empirical methods, which work fine when encountering known or usual ground conditions. However, coal mining approaches depths where little experience exists and numerical modeling is often the only method to estimate ground behavior. This paper discusses the geotechnical properties relevant to numerical model and focuses particularly on input values for modeling resin grouted rock bolts for safe gate design.

Jan 1, 2006

By D. Brady

There are many examples, historical and recent, from the underground coal mining industry where during emergency response the response and ultimately the outcomes, could have been significantly improved if adequate systems had been in place for the collection and management of relevant information preceding the incident, the acquisition of information during the incident and the use of the information for risk mitigation and decision making purposes. The subject and process of knowledge management is possibly the most critical for would be rescuers of endangered coal mine workers, as it has been demonstrated at numerous coal mine incidents that a lack of or mismanagement of crucial information can be fatal for both the rescuer and/or the endangered coal mine worker. This paper will underline the scope and importance of robust knowledge management systems for emergency response within the underground coal mining industry and the process by which it is being achieved within the Queensland Mines Rescue Service and the NSW Mines Rescue Service.

Jan 1, 2012

By B. Erdem

This article introduces a computer model, which emphasizes panel design for draglines deployed in direct side-casting mode. The study covers flat and inclined coal-seam conditions with the dragline operating along the strike-line. Two casting methods are embedded in the model: material is placed in the open set adjacent to the one on which the dragline is located (the DNS method) and material is placed in the open set adjacent to the one the dragline excavates (the DND method). While in the first method the unproductive walking time is reduced as the set is enlarged, in the second method the cycle time is lessened as the dragline swings along an acute angle. The side-casting model is shaped so as to provide several panel configurations instead of a single one to conform to the characteristics for an opencast mine. This is achieved by assigning the pit width an interval of values ranging from a minimum to a maximum. The model includes solutions to other critical design parameters such as: set length, swing angles at key cut and main cut positions, and required dragline reach at key cut and main cut positions. The model outcomes reveal the following: the stripping operation is largely affected when the coal-seam is inclined. The downhill spoiling mode should be applied wherever possible. The DNS pattern allows wider pit width intervals as well as longer sets and longer reaches.

Jan 1, 2004

By Tony S. Calayag

Throughout the mining industry today, new bearing materials - ZA* high-performance zinc-aluminum alloys - are reducing costs of maintaining and rebuilding a wide range of equipment. As replacements for bronze bearings, installed in original equipment at the plant or during maintenance and repair operations in the field, the zinc alloys frequently provide better or equal performance at lower cost. The ZA Alloys The ZA alloys are a family of three high-performance zinc-aluminum alloys that compete in cost and performance with cast iron aluminum and bronze. The growing number and uses testifies to the versatility of these alloys and is encouraging their consideration in a wider range of applications. The ZA alloys are referred to as ZA-8, ZA-12, and ZA-27, the numbers corresponding approximately to the percentage of aluminum each alloy contains. ZA-8 is a permanent-mold casting alloy and is usually selected for decorative purposes; ZA-12 provides both performance and cosmetic benefits; ZA-27 offers the greatest functional strength. The term high performance ZA alloys distinguishes them and their improved engineering properties from traditional zinc die casting alloys. Maintenance Savings At its mine in Timmins, Ontario, Kidd Creek Mines Ltd. operates over 40 Joy VCR- 150 crawler-mounted air-powered rock drills. Most of the drill components undergo severe stress as the drill batters through the under-ground rock. As the components wear, the drill bits wobble; when the wobble becomes excessive, the drills are rebuilt. In the gear train, which rotates the drill steel, there are three planetary gears with - historically - bronze bushings. Since the planetary gear bushings are wear items, they are routinely replaced during overhaul. The bronze planetary gear bushings (three bushings per assembly) were replaced up to five times annually. With 43 drills in use, bushing consumption approached 600 per year. At the manufacturer's replacement part cost, the 600 bushings and gears would cost more than $20,000 a year. Even though a major saving was achieved by having the bronze bushings manufactured locally, the 600-unit annual usage provided ample incentive to investigate other ways of lengthening drill life and reducing the part costs. One approach was to consider using a bushing material that offered good bearing properties, but was lower in cost. About three years ago, ZA-12 zinc-aluminum casting alloy, costing less than half as much as bronze, was evaluated and selected for testing. One hundred ZA bushings were manufactured and placed in service as the drills came in for rebuilding. At the next rebuild the "drill doctor" (drill maintenance mechanic) noticed that, although the bronze bushings were completely destroyed, on occasion the zinc alloy bushings were not. In addition, he noted that some of the ZA bushings showed less wear than the bronze bushings. Because the bushings were changed routinely during each overhaul, the actual operating life of each bushing was not determinable. Therefore, it was not possible to statistically compare the life of the ZA bushing against the bronze. However, the desired life of the part was from overhaul to overhaul. So the ZA alloy obviously met the objective, giving equal or better life than bronze at a significantly lower price. Based on the favorable results of the testing under actual operating conditions, Kidd Creek maintenance personnel decided to switch permanently to the ZA bushings for rebuilding the VCR-150 rock drills. Original Equipment Application As one of the leading companies marketing the ZA alloys, as well as a zinc -copper-silver mining company, Kidd Creek is interested in developing applications for the alloys by original equipment manufacturers such as joy Manufacturing. Kidd Creek marketing representatives provided joy with information on the Timmins mine tests, along with ZA-12 bushings for evaluation and testing. Based on this information, joy installed ZA bushings in 12 new VCR-150 units and delivered them to customers for use in such areas as granite quarries and copper, lead, zinc, and limestone mines. During the following year, joy engineers closely monitored repair reports to verify the performance of the ZA part. The engineers' findings convinced them of the advantages of ZA-12. As a result, joy now uses ZA-12 bushings in the manufacture of its VCR-150 air tools. Advantages for Casters and Users In the foundry, the new alloys have proved their castability and profit potential in sand and metal permanent-mold processes, as well as the new graphite permanent-mold gravity casting process. The energysaving, pollution-free and ease-of-machining benefits they offer are important to all of these processes. Most recently, the high-performance alloys entered the arena of cold-chamber die casting, where they provide properties beyond those of

Jan 7, 1983

By H. C. Li

Mechanical models are established in accordance with the degree of mining on both sides of the coal pillar, and formulae were derived which calculated the superposition stress distribution and the width of the plastic region. The stability of the coal pillar was analysed and a reasonable size of coal pillar determined, in accordance with the elastic region rate. Further practical examples for the stability of the coal pillar are calculated and simulated.

Jan 1, 1992

By Greg Barnes

Agenda ? The Mining Stock Life Cycle ? Current Environment ? Valuation ? Golds ? Valuation ? Base Metals ? Case Study ? Quebrada Blanca Hypogene Commodity Investment Cycle ? Macro-Economic Indicators ? LME Inventories ? watch the trend; rising inventories ? bad for prices, declining inventories good for prices ? OECD Leading Indicators ? PMIs ? Purchasing Manager Indices ? Industrial Production ? more important for metals consumption than GDP ? Housing Starts ? US, Europe ? Auto Sales ? All things China ? metal imports/exports; SHFE inventories; SRB stockpiling ? Seasonality ? it does play a role ? What is Chris Dutton (TDSI Quantitative Analyst) saying?

May 1, 2010

By C. F. McCarroll

The effectiveness of an industry's safety activities can be gaged best by the accident records of that industry. In an effort to gage conditions in the petroleum industry, and with the objective of helping to reduce the number of accidents in it, the Bureau of Mines from time to time has tabulated, analyzed, and published pertinent statistical information.3/. These reports have dealt with distribution, causes, and costs and related phases of accidents for various and collective divisions of the petroleum industry in several sections of the country. This type of study aids the personnel of the Bureau in planning the course of its activities in accident-prevention work and gives useful data to persons engaged or interested in the promotion of safety in the petroleum industry, which will aid them in their efforts to reduce the number and severity of accidents. A majority of petroleum operators and "service? contractors have acknowledged their responsibility to provide their employees with safe working conditions and to their stockholders for greater economic value of invested capital by establishing safety divisions within their respective organizations. Such divisions have a primary duty, namely, to see that properly designed and guarded machinery and working equipment are furnished the employees and that they are trained in the safest practical methods of performing their work. Some companies and individual operators, however, have shown little or

Jan 1, 1939