Search Documents

By Bernard Hertlein

¦ Drilled shafts resist scour seismic loads better than groups of driven piles ¦ Drilled shaft construction creates less noise and vibration than driving piles ¦ Drilled shafts permit direct observation of bearing stratum, and confirmation of location ¦ Drilled shafts are cost effective

Jan 1, 2001

By Calvin K. Lee

This Bureau of Mines report describes a simple fire-retardant treatment for wood. The treatment involves preheating the wood surface at high heat flux (~0.6 cal/cm2 sec) to form an in situ surface char layer (~3 mm thick) on the wood. Laboratory-scale fire tests show that the precharring technique improves the fire-resistance of virgin wood by decreasing and delaying generation of volatile gases through thermal insulation effect of the surface prechar layer.

Jan 1, 1978

By C. W. Owings

One phase of Bureau of Mines health and safety work is promotion of the use of safe and effective dust-collecting devices in connection with rock drilling in coal mines. To insure that adequate equipment of this type is available to the coal-mining industry, the Bureau of Mines conducts investigations and issues approvals for dust-collecting equipment that meets the requirements of a schedule established for testing dust collectors intended for use in connection with roof drilling for roof bolting and for other rock drilling. 6/ Performance tests are conducted under the provisions of this schedule by engineers of the Branch of Health Research. This circular describes briefly the requirements and procedure for approval and lists drill-dust collectors that have been granted approval as of January 31, 1956. The addresses of manufacturers of approved devices are listed alphabetically at the end of this circular.

Jan 1, 1956

Particles of a complex nickel sulphide concentrate (containing pyrite, pyrrhotite, pentIandite, and violarite as the major mineralogical constituents) were entrained in a stream of hot gas the temperature of which was varied from 500 to -1000°C. Chemical analysis of the particulates collected from the furnace was used to detect the rapid change in sulphur content which accompanied the ignition temperature jump. X-ray diffraction analysis was used to characterize the oxidized material.These techniques showed that ignition was dependent on the mineralogical composition and occurred over the temperature range 500-900°C. Pyrite ignited first in the range 500-600°C; pyrrhotite was the least reactivemineral and required temperatures in excess of 800°C for ignition. The nickel minerals <pentIandite and violarite decomposed before ignition and ignited at temperatures intermediate to those required for the pyrite and pyrrhotite. The ignition temperature for the pyrite was found to be independent of particle size and concentration of oxygen in the atmosphere.Ignition temperatures determined by the simulated flash smelting method were compared with the results of differential thermal analysis (DTA) measurements performed on the same concentrate. Temperaturesdetermined in the DTA test as corresponding to the start of exothermic activity were shown to be at least 100°C below those determined by the simulation test.

Jan 1, 1978

By Derek Ellis

Volume II of this two-part series on Submarine Tailings Disposal (STD) as a tailings management option for coastal and island mines contains descriptions of lesser known case histories. The Misima gold mine (Papua New Guinea) and the Black Angel lead-zinc mine (Greenland) are described in some detail as the best documented cases. Atlas copper mine (The Philippines) is less fully described due to relative lack of documentation. The Misima and Atlas STD systems are working to their design criteria. At Black Angel the system adopted did not prevent contamination for a number of reasons, which are now understood. Two cases are described where STD is being developed. They are the Cayeli Bakir copper mine Turkey), and the Toquepala and Cuajone mines (Peru). There is excellent documentation available for both cases. Three case histories are described where tailings have reached the sea either through beach or river discharge. In one case the STD option has been explored (Marcopper Mine, The Philippines). In the others we explore in hindsight whether STD might have been a viable alternative using the Screening Criteria that this Volume develops - see below. The mines are Bougainville Copper Mine in Papua New Guinea, and Jordan River Mine (Canada). There is potential for STD at all three sites. Finally, the Volume presents Screening Criteria for appraising STD, based on the experience in design, operation and environmental impact reviewed in the case histories.

Jan 1, 1994

By Benoit Virollet

Over the last 10 years the diameter of unbraced, unlined and unanchored circular shafts has grown dramatically in many parts of the world. This progress has taken place through improvements in: construction methods; concrete rheology; and design capabilities. Excavation equipment has become more precise in terms of operator control and ability to correct alignment of digging elements leading to better alignment tolerances. Also contributing to the increases in shaft diameters is the evolution of design models. A better understanding of soil structure interaction is being incorporated into the analyses in terms of radial soil stresses and imposed loads on the shaft. This paper provides an overview of the recent progress made in circular shaft construction, the primary design considerations, and some innovative uses of efficient arc elements to develop unsupported structures of other shapes. In addition, a summary of recent circular shafts constructed worldwide is provided.

Jan 1, 2006

By B. J. Madden

Over 206 million tons of hard coal were mined in South African collieries in 1996. Some 132.5 millions tons came from underground operations and approximately 120 million tons came from bord-and-pillar workings resulting in between 100 000 and 150 000pillars being formed. Coal pillar design remains a significant feature of South African mining. This paper reviews South African coal pillar design procedures in the light of 90 pillar collapses that have occurred since 1904. It shows that, while the current pillar strength formula is still valid within the original empirical range of Salamon1,cognisance must be taken of local conditions. Current South African coal pillar research is attempting to account for the variations in local conditions with the emphasis on the effect of discontinuities and pillar deterioration. It is suggested that a more holistic approach to pillar design be adopted to include a design methodology that examines the stability of the roof, pillar and floor of the underground workings. Using this approach, deviations from the empirical database used by Salamon and Munro will be incorporated into the design methodology resulting in more stable underground workings.

Jan 1, 1998

By Alexander Filotti, Stanley Merjan

"Abstract. The paper shows the benefits and accomplishments of this relatively new but established product on the pile foundations market in the United States. The first part of the paper describes general aspects of the design, construction, and geotechnical capacity (designed and in situ) of Tapertube piles. The qualities resulting from the design and manufacturing of the Tapertube pile will be presented first.The second part of the paper describes the installation of Tapertube piles for an addition to Terminal One at JFK International Airport and The Edge development. A carbon print analysis for both projects is developed using the EFFC-DFI carbon print calculator. For the JFK project the benefits of using BIM in redesigning the project for Tapertube piles are explored.General description.The tapertube pile consists of a tapered tubular bottom section attached to a conventional pipe extension. The 50 ksi steel for the taper is mechanically folded into a polygonal cross-section (usually 12-sided) with a longitudinal welded seam. The tapers are fabricated in many sizes with bottom diameters varying from 8 to 14 inches, top diameters from 12 to 20 inches, lengths from 10 to 35 feet, and steel thicknesses from 3/16 to 1/2 inch. A conical steel shoe or a flat plate is welded to the bottom of the taper and the top of the taper is circularized to match the outside diameter of the pipe extension. The inclination of the tapers is generally between 1.5% and 2.5%.The pipe extension is fully butt welded to the taper and has the necessary length for the pile to develop the requisite capacity. Concrete fill for the piles is generally 4,000 p.s.i. or more. Typically the piles are shopassembled and shipped to jobsites in lengths to 80 feet."

Jan 1, 2014

By M. R. Geer

Efforts to evaluate washery performance are nearly as old as the art of coal cleaning, and in former years there was no uniformity in either the methods used or the basic terminology employed. This situation, and the con- fusion it bred, prevailed until about the time of the First International Coal Preparation Conference in 1950, Largely because of the interest of the French coal research organization Cerchar, the subject of evaluating performance was given prime importance at this conference. As a result, there is now a much greater degree of uniformity in terminology and methods of expressing cleaning results. The International Standards Organization currently is working toward international standards of terminology and methods that should improve the situation even more. The various criteria that are used to evaluate the performance of coal- cleaning equipment fall into three categories, depending upon the extent to which they are dependent on the density composition of the raw coal; some are directly dependent, others are only indirectly dependent, and still others are substantially indenpendent.

Jan 1, 1962

The following report summarizes the results of engineering feasibility studies whose purpose was to assess the probable efficiency, reliability, safety and cost of a number of possible methods for removal of radon gas from the ambient air in underground mines. Fourteen candidate techniques were evaluated. Seven of these were based on specific individual principles, and seven were based on combinations of these principles. The individual principles were as follows: 1. Activated charcoal 2. Organic fluids 3. Semipermeable membranes 4. Molecular sieves 4. Cryogenics 6. Chemical reaction 7. Centrifuge The combinations were: 8. Cryogenics and activated charcoal 9. Cryogenics and molecular sieves 10. Cryogenics and chemical reactions 11. Membrane filters and organic fluids 12. Membrane filters, cryogenics and activated charcoal 13. Membrane filters and chemical reactions 14. Silica and an Organic Fluid

Jan 1, 1975

By K. K. Landes

The north central and northeastern states supply over 50 pct of the chemical and metallurgical limestone produced annually in the United States, and Ontario is the leading source of this material in Canada. About three fourths of the chemical and metallurgical stone produced in this area comes from Michigan, Pennsylvania, Ohio, and Ontario. The specifications, physical and especially chemical, for chemical and metallurgical stone depend upon the end use, but in general the tolerance for impurities is so low as to rule out most limestones and dolomites. Both high calcium limestone and dolomite are used in the metallurgical and chemical industries. The principal metallurgical use is as a flux in iron ore blast furnaces and open hearth steel furnaces. The major chemical uses are in lime burning and soda-ash manufacture. Other important uses include glass manufacture, in making calcium carbide, and in sugar factories. All deposits of high quality carbonate rock are definitely finite. Invariably and inevitably they diminish in either thickness or quality laterally so as to become unworkable as chemical and metallurgical stone. The size of these high quality lenses ranges from a few thousands of tons to hundreds of millions of tons. The best hunting for new supplies is in the geologic formations known to contain premium quality deposits. However, because of high transportation costs, carbonate rocks, to be workable, must be close to market, dollarwise. Definitions: Chemical stone is limestone or dolomite used as a raw material by the chemical industry. The major chemical uses are in lime burning and soda-ash manufacture. Other important uses include glass manufacture, making calcium carbide, and in sugar factories. The specifications for chemical stone depend entirely upon the end product. Some uses require dolomite, some require high calcium limestone; in a few instances, notably in lime burning, either type of carbonate rock can be used as raw material. As a general rule, a fairly pure stone is necessary and for certain particular uses the tolerance for some elements such as sulfur, iron, and phosphorus may be extremely small. Metallurgical stone is used as a flux in furnace operations, especially in the blast furnace where iron ore is converted into pig iron and in the open hearth furnace where pig iron is made into steel. Either limestone or dolomite can be used in the blast furnace, but only high calcium stone is charged in the open hearth (except for rice-size dolomite used as a refractory). There are no rigid chemical specifications for blast furnace stone, but low silica, alumina, sulfur, and phosphorus are desirable. For open hearth use, in addition to low magnesia, a very low sulfur content is also specified by many furnace operators. For furnace use, fluxstone also must be sufficiently shatter resistant that it will remain in lump form during transport and charging into the furnace. Commercial stone is the term applied in the trade for crushed stone used for roadstone and in concrete aggregate. Many of our best chemical and metallurgical limestones are too soft to qualify in the Los Angeles abrasion test for use as commercial stone. However, some limestones, and a higher proportion of dolomites, do qualify for commercial stone and so can be sold to either market. Place Value: Even the highest grade limestone is still a bulk commodity with a relatively low value per ton. As a matter of fact there is very little difference in the average price per ton between high grade chemical and metallurgical stone and crushed limestone used commercially. Most high quality stone is produced in large operations with consequent low cost per ton whereas most commercial stone is produced in relatively small local quarries. As in the case of other bulk commodities most limestone buyers pay more for transporting the raw material than the cost of the stone at its source. For this reason steel furnaces and chemical plants

Jan 1, 1961

By K. A. Lewandowski

The efficiency of heap leaching is reduced by poor solution flow characteristics (i.e., channeling and ponding) that result from fines migration. Agglomeration of the ore can immobilize fines, but for agglomeration to be successful in copper leaching, an acid-resistant binder is needed to stabilize the agglomerates. Until now, there has not been a satisfactory method to evaluate whether a binder was effective, other than squeezing a handful to see if it ?feels right.? This paper reports on several procedures that have been developed to quantitatively determine whether a binder gives good performance in an acidic solution. These procedures have been used to identify binders that would be suitable for copper heap leaching.

Jan 1, 2008

By Thomas M. Barczak

Wood cribs are used extensively to stabilize openings in underground coal mines. This U.S. Bureau of Mines report describes the results of full-scale testing of several multitimbered wood crib configurations. Multitimbered configurations are wood cribs that are constructed with two or more timbers per layer. Nine different crib configurations were evaluated. Configuration parameters under study included the aspect ratio (height-to-width relationship) and the percentage of solid rr:aterial used in crib construction. Test results and generalized wood crib behavior are discussed and recommendations are made concerning crib constructions to maximize strength and stability. Crib performance is enhanced by reducing buckling effects by decreasing the aspect ratio and geometry considerations that increase the moment of inertia. A cost benefit analysis of multitimbered wood crib configurations is made. Generally, increasing the percentage of solid provides more resistance at less unit construction cost. A comparison of laboratory results and underground observations of several wood pack wall supports suggest in situ load capacity is less than that measured in laboratory testing. Reasons for the apparent decrease of in situ load-bearing capability include load rate effects, stiffness of reaction surfaces, and varying boundary conditions that alter the load transfer mechanics of the crib structure.

Jan 1, 1991

By Henning E. Soderberg, Robert Brien, O&apos

Coal may be the answer to US energy problems, but it also has its drawbacks. If it is crushed, screened, dumped, or moved, the environmental engineer is faced with a dust problem. To control coal dust, at both minimum initial cost and reasonable operating cost, demands a working knowledge of dust control equipment design, as well as the coal handling operation. Here are some guidelines to reduce air volume requirements and cut overall system costs.

Jan 10, 1981

By James H. Prout

Roof warning signals were studied in 18 mines covering 5 coal seams. The results of this study confirmed that roof talk must be interpreted for each individual mine after all other conditions are present that indicate danger of roof fall. Characteristics of roof talk pulses were studied to ascertain features used in interpretation. Roof talk pulse decay time was found to be typically 0.1 to 0.5 seconds depending on the dimensions of the entires. Time between roof talk pulses was found to correlate inversely with the degree of danger under certain conditions. Roof talk and machinery noise recordings obtained during this study were used for subjective tests of ear protectors in a simulated coal mine noise environment. These tests required a detailed interpretation of roof talk and yielded results with high statistical power. Results of these tests showed that the use of personal ear protectors in high noise levels does not degrade a miner's ability to discriminate speech and roof talk. A training course was developed to encourage coal miners to pro-tect their hearing by proper use of personal hearing protectors.

Jan 1, 1973

By D. H. McCain

Through a unique partnership between the Colorado Mine Safety and Training Program (CMSTP), the Colorado Rock Products Association (CRPA) and the Higher Education and Advanced Technology (HEAT) Center, a video packed, dazzling CD-ROM training program was developed for new miners entering the aggregate industry. Why this product was developed, and why the aggregate industry, will be discussed along with the challenges faced throughout the project. Cooperation from every one involved including MSHA made this the product of which all other training materials in the mining industry will be measured against in the 21st Century. This product's versatility and wide application makes it a tool that is as critical to a mine's success as any earth moving machine. Developed with both state and federal grant moneys allows this product to be affordable to small operators and independent contractors. The quality of this two CD-ROM set rivals any commercially made CD-ROM training.

Jan 1, 2001

By LaMar G. Evans

The rapid determination of uranium in ores by radiometric means was investigated by the Bureau of Mines. Among the various procedures and schemes tested, two showed most promise. They were the ratio scheme developed in the Bureau's Tucson, Ariz., laboratory and the equilibrium method developed by the Canadian Department of Mines and Technical Surveys. The ratio method is a simple, empirical procedure for classifying the state of equilibrium in ores by measuring their radioactivity by means of a Geiger-Muller counter under three different conditions, using filters. The principal merit of the method is in providing a clue as to the reliability of equivalent uranium determinations.

Jan 1, 1958

By C. Wen

In Huoqiu region of Anhui Province, Fe2O3 occurs mainly in the form of specularite. Besides quartz, the gangue minerals include iron-bearing silicates such as chlorite and sericite which account for about 10% of the total gangue. The separation effect of conventional collectors is poor in the flotation of the minerals, that is, the average grade of iron concentrates is only 60-62%. Using the developed amphoteric collector can successfully realize not only the separation of specularite from various gangue minerals with results of iron concentrate grade above 65% and iron recovery of above 80% but also low temperature flotation at 15°C.

Jan 1, 2012

By Bali. D. D., S. Chattopadhyay

"The planning and construction of prime coking coal beneficiation plants in the nationalized mines in India are reviewed. Flow schemes, construction practice, materials consumption, and costs are detailed.Medium-capacity beneficiation plants with multiple loops are recommended under Indian conditions.IntroductionThe reserve of high-grade and easily washed metallurgical coal in India are quite limited. Prime coking coal constitutes approximately 22% of the total resources and occurs exclusively in the Jharia coalfield in the state of Bihar. Bharat Coking Coal Limited (a subsidiary of Coal India Limited (CIL) the nationalized mining sector of India) owns 80% of the Jharia collieries. The development of Jharia coalfield in the pre-nationalized period before 1971 has been characterized by a large number of small mines with primitive mining methods and low productivity. The production of prime coking coal to meet the demand of the steel industry in India has to increase from the existing level of 11.1 million tonnes to 43.4 million tonnes per annum by 2000 AD, thereby producing 5.61 million tonnes and 22.7 million tonnes of clean coal respectively. An ambitious program has been undertaken for development of bigger mines with an average production of 1 to 3 million tonnes per annum. With the fast dwindling reserves of good quality coking coal, more inferior grade coal seams, having difficult washing characteristics, are now being mined. All the coal from the future mines will have to be beneficiated to make it suitable for consumption of steel plants; the following washeries are being planned for construction by 2000 AD:"

Jan 1, 1986

By Nicholas J. Grant, H. C. Chang

TRANSCRYSTALLINE fracture surfaces of the cleavage type have been examined by microscopy and X-rays for several metals.' These investigations revealed that the fractured surfaces were not flat and invariably had cleavage and other deformation markings on them. On the other hand, the study of inter crystalline fracture surfaces has been limited. Perryman, in a recently published paper on the inter crystalline fracture of ß-brasses,' found that a thin layer of heavily deformed metal was invariably associated with these surfaces. Furthermore, the thickness of this layer was found to depend on the orientation of the grain boundary surface with respect to the applied stress. The mechanisms of grain boundary sliding and intercrystalline fracture have been presented in two previous papers,which described certain aspects of the deformation of a 20 pct Zn-A1 alloy. It is the purpose of this paper to present some observations on the structure of intercrystalline fracture surfaces and to correlate the structure of such surfaces with the mechanism of intercrystalline fracture. Experimental Techniques—The high purity 20 pct Zn-Al alloy was generously supplied by the Research Laboratories of the Aluminum Co. of America. Two sizes of specimen were used; the first had two parallel flat surfaces of dimensions 1x0.17x0.09 in. and the second was round with a 0.25 in. diam. A grain diameter of 1 to 3 mm was obtained by annealing the specimens at 1000°F for 24 hr. The specimens were then air cooled. The specimens were subjected to creep at 500°F and 2300 psi. The rupture times ranged from % to 3 hr, with one room temperature tensile test. It has been mentioned previous1y" that the intercrystalline fracture surfaces of this alloy, when tested under the conditions given above, are sharply defined. In the optical examination of the fracture surfaces, whenever possible, magnifications of at least X250 were used. The locations of the regions examined, both optically and by X-rays, were selected to give several fracture surface orientations with respect to the stress axis and to the specimen surfaces. This was possible for the X-ray studies since the grain diameters were large compared to the X-ray beam. A film to specimen distance of 3 cm, a 1 mm pinhole and Cr radiation were used for the Laue back reflection pictures.

Jan 1, 1957